FCC ID: 2AOVU-IPA1104HDW 4K HDMI dongle

These devices comply with part 15 of the FCC rules, as well as the Canadian Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:: (1) the device should not cause harmful interference; and (2) the device must accept any interference received. Including interference that may cause poor operation Ce matriel est conforme la partie 15 des rgles FCC [et aux critres d 'exemption des licences industrielles canadiennes (RSS)].L 'opration d 'exemption des licences industrielles canadiennes (RSS)].L 'opration doit satisfaire aux deux conditions suivantes: 1) l' quipement ne doit pas causer d 'interfrences nuisibles; et 2) l' quipement doit accepter toute interfrence reue, y compris toute interfrence pouvant conduire des oprations indsirables Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body. Pour se conformer aux directives de la Commission fdrale des communications Pour se conformer aux directives de la Commission fdrale des communications relatives l 'exposition aux radiofrquencesLa distance minimale entre l'installation et le fonctionnement doit tre de 20 cm.

Label & Label Location FCC ID: 2AOVU- IPA1104HDW This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Size: 45mm(L)*30mm(W)

Label & Label Location FCC ID: 2AOVU- IPA1104HDW IC: 25669-IPA1104HDW Model: IPA1104HDW-01-400-05T-TiVo Size: 45mm(L)*30mm(W) Label & Label Location FCC ID: 2AOVU- IPA1104HDW IC: 25669-IPA1104HDW Model: SN8BABB Size: 45mm(L)*30mm(W)

Shenzhen SEI Robotics Co., Ltd. 501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China Date: 2020/7/15 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID:

Original Grant Date:

Applicant:

Shenzhen SEI Robotics Co., Ltd. 2AOVU-IPA1104HDW 01/08/2020 Dear Examiner, This is to request a Class II permissive change for FCC ID:

2AOVU-IPA1104HDW and 5500 5720MHz evaluated 5260-5320MHz and in UNII bands by software. upon EMC and RF exposure to ensure RF characteristics do also without The major change filed under this application is:

1. Enabling channels Evaluation has been done not degrade and comply with rule part 15.407. The mechanism of radar detection is been radar detection capability. 2. unchanged in this permissive change application. 3. The security mechanism in the firmware is remained unchanged as it is in original grant conditions. requirement compliance transmitter hardware remained 905462 Comply design device affect Client may KDB The that this with of as is a Sincerely, Signature Jason Zhao Attestation Engineer Shenzhen SEI Robotics Co., Ltd.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: July 16, 2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name IPA1104HDW- 01-400-05T-TiVo,SN8BABX(X=A TO Z) 2AOVU-IPA1104HDW For the product stated above, we request that the following information be held confidential;

Exhibits Long-Term Short-Term Short-Term Confidentiality Confidentiality Confidentiality Days 180 180 180 180 External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions Label and Label Location The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name:

Jason Zhao Company:

Shenzhen SEI Robotics Co., Ltd. Address:

501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China Phone:

86 0755-26613121 Fax:

86 0755-26734204 E-Mail:

zhaoys@seirobotics.net

Shenzhen SEI Robotics Co., Ltd. 501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China 7/28/2020 We, Shenzhen SEI Robotics Co., Ltd., the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID:

2AOVU-IPA1104HDW including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

Sincerely, Signature Jason Zhao Attestation Engineer Shenzhen SEI Robotics Co., Ltd.

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID2AOVU-IPA1104HDW

(1) DFS Device:

Master N/A Client with Radar detection capability Client without radar detection capability,

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning

(where the device is can listen only with no 5745-5825 5755-5795 5775-5775 5180-5240 5190-5230 5210-5210 5260-5320 5270-5310 5290-5290 5500-5720 5510-5710 5530-5690 Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No probes) Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No No

(3) Country code selection ability Yes If yes, pls explain how it was implemented:

Ad Hoc Mode Capability Access point Capability Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No

(4) Meet 15.202 requirement Yes No pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non- DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Does not apply Sincerely, Name:

Company:

Address:

Phone:

Fax:

E-Mail:

Jason Zhao Shenzhen SEI Robotics Co., Ltd. 501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China 86 0755-26613121 86 0755-26734204 zhaoys@seirobotics.net

Difference description FCC ID: 2AOVU-IPA1104HDW Model: IPA1104HDW- 01-400-05T-TiVo,SN8BABX(X=A TO Z) The 4K HDMI dongle manufactured by Shenzhen SEI Robotics Co., Ltd. needs to apply for FCC certification. The applied models are as above. They are All the same except for the shape and color of cover, even the principle of the circuit, the electrical structure and all key components related to safety and electromagnetic compatibility are the same. The difference does not affect electromagnetic compatibility and safety. Company:

Name:

Jason Zhao Company:

Shenzhen SEI Robotics Co., Ltd. Address:

501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China Phone:

86 0755-26613121 Fax:

86 0755-26734204 E-Mail:

zhaoys@seirobotics.net

Shenzhen SEI Robotics Co., Ltd. 501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

1/4/2020 We, Shenzhen SEI Robotics Co., Ltd., the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID:

2AOVU-IPA1104HDW including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Signature Jason Zhao Attestation Engineer Shenzhen SEI Robotics Co., Ltd.

501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, Shenzhen SEI Robotics Co., Ltd. China Date: January 8, 2020 FCC ID: 2AOVU-IPA1104HDW IC: 25669-IPA1104HDW FCC Model No.: IPA1104HDW-01-400-05T-TiVo, SN8BABX(X=A TO Z) ISED Model No.: IPA1104HDW-01-400-05T-TiVo, SN8BABB To:

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Certification and Engineering Bureau Industry Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 To Whom It May Concern, We, Shenzhen SEI Robotics Co., Ltd., declare that this EUT (FCC ID:

2AOVU-IPA1104HDW/IC:25669-IPA1104HDW) doesnt have Ad Hoc mode function onnon-US/Canada frequencies. Inaddition.The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Jason Zhao Shenzhen SEI Robotics Co., Ltd. 501, Block A, Productivity Building #5 Hi-tech Middle 2nd Road, Nanshan District, Shenzhen, China 86 0755-26613121 86 0755-26734204 zhaoys@seirobotics.net Name:

Company:

Address:

Phone:

Fax:

E-Mail: