FCC ID: 2A5W7YZC-06 xbox 360 wireless 2.4G controller

MUTI-PLATFORM WIRELESS CONTROLLEP

(wireless receiver) Product Features 1. The handle is mainly X-360 host, but also supports Windows computer and P3 host. 2. The handle supports dual motor vibration function. 3. Wireless 2.4G connection, strong anti-interference ability, stable connection signal, and free control. 4. There is no need to load any drivers, the handle is connected to the 360 host/

P3 host / PC computer be usable. 5. The PC can be switched to X-input or D-input at will without loading any drivers. 6. When the handle is charged, the game can also be played normally. 7. The handle (receiver) can be upgraded with updated software by connecting to a computer. Warm Tips: The wireless receiver only can compatible with this controller,it can`t work with the original X-360 cantroller. Function key Back Start Left Joystick D-pand RB Key RT Key Y:

X:

B:

A:

Body sensors Tracking Install/Right Joystick Back Confirm Right Joystick LB Key LT Key Instruction Manual Battery box Charging Port Pairing Key 1. Introduction to buttons Handle end:

1. X-360 key*1: Turn on the handle or execute commands from the host, and switch between X-Input and D-input. 2. Direction keys*1 group: up, down, left, right. 3. Function control keys *10: A, B, Y, X, LB, RB, LT, RT, BACK, START 4. Left and right joysticks*2: 3D joysticks, including joystick buttons. 5. Reset button *1: Press this button to turn off the power of the handle, and disconnect the handle from the receiver (reset). Second, even machine guidance 1. Connect to the 360 host via 2.4G wireless Note: In P3 host/PC computer mode, there is no vibration function. 3. Connect to PC computer wirelessly via 2.4G When the PC computer is turned on, connect the USB connector of the receiver to the PC computer. At this time, the receiver LED light starts to flash to enter the pairing mode, and then press the X-360 button on the handle to wake up the handle, and the handle LED1~LED4 flashes for pairing, the pairing is successful After the receiver LED is always on, the handle LED2 is always on to operate, and the PC computer is connected to the X-input mode by default; long press the handle X-360 button for 5 seconds, it will switch to D-input mode, at this time the LED1 on the handle, LED2 is always on, and the handle is in PC digital mode at this time. Short press the X-360 key to switch the cross key mode, when LED1 is on, it is the PC simulation mode.Remark 1: In PC mode, there is no vibration function. When the 360 host is turned on, connect the receiver's USB connector to the 360 host. At this time, the receiver's LED light starts to flash to enter the pairing mode, and then press the X-360 button on the handle to wake up the handle, and the handle LED1~LED4 flashes for pairing, pairing After success, the receiver LED is always on, Handle battery display and the handle channel light is always on to operate. 2. Connect to P3 host via 2.4G wireless When the host is turned on, connect the USB connector of the receiver to the P3 host. At this time, the receiver's LED light starts to flash to enter the pairing mode, and then press the X-360 button on the handle to wake up the handle, and the handle LED1~LED4 flashes for pairing, the pairing is successful After the receiver LED is always on, and the handle channel light is always on, the operation can be performed. charged. 1. When the handle is connected to the X-360 dedicated charging cable for charging, the red LED on the charging cable lights up, indicating that the handle is charging. When the light on the X-360 dedicated charging cable turns green, it indicates that the hand is now fully charged and the handle The battery pack is fully 2. The handle can work normally and vibrate when the battery power is greater than 2.2V, but the handle will be disconnected when the power is too low when the battery power is lower than 2.1V. At this time, replace the battery (dry battery) or charge the Note: When the handle uses 1.5V dry batteries, do not charge the handle to avoid battery (battery pack). danger! ! !

Specifications Connection Way:

2.4GWireless (Include receiver) working voltage :

3.0V Working current :

25mA(motor doesn`t vibrate) 180mA(motor vibrate) Range:

Size:

Weight:

Color:

8~10m 152*105*58mm 249g Black / White Plug the wireless receiver into the USB port of the X-360 host. Install the 2AA or rechargeable batteries in the battery box(Battery is not included.) Connect TV Havge fun playing games Applications:

X-360 Console,PC,P3 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction

Shenzhen SND Electronics Co., Ltd. Agent Authorization Company: Shenzhen SND Electronics Co., Ltd. Address: 4 Floor, Building1#, Laobing industry, Tiezi Rd, Gongle, Xixiang, Baoan, Shenzhen Product Name: wireless controller Model Number(s): YZC-06, YD-089 Product Description: wireless controller We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: 2022-04-06 Signature:

Name:

Lisa Fu Title:

Manager Company: Shenzhen SND Electronics Co., Ltd.

Shenzhen SND Electronics Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022/04/06 Subject; Request for Confidentiality FCC ID: 2A5W7YZC-06 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Lisa Fu Title: Manager

Shenzhen SND Electronics Co., Ltd. Model Difference Data2022.04.06 Product description: wireless controller Model name: YZC-06, YD-089 Trade Name: N/A FCC ID: 2A5W7YZC-06 All the model are the same circuit and RF module, except model names . Regards Sincerely Clients signature :

Clients name / title : Lisa Fu (Manager) Contact information / address: 4 Floor, Building1#, Laobing industry, Tiezi Rd, Gongle, Xixiang, Baoan, Shenzhen