1 Contents 1Introduction................................................................................................................................................. 3 1.1 Application background........................................................................................................................... 3 2 System (the) introduction................................................................................................................................... 4 2.1 System composition and principle block diagram in the paper......................................................... 4 2.1.1 Diagram of the system of the..................................................................................................... 4 2.1.2 System principle outlined............................................................................................................ 4 2.2 The composition and principle block diagram in the paper............................................................... 5 2.2.1 The block diagram of................................................................................................................... 5
................................................................................................................................................................... 5 2.2.2 The principles outlined ................................................................................................................ 5 3Function .................................................................................................................................................................. 6 3.1.1 Rf index.................................................................................................................................................. 6 3.2 structure .................................................................................................................................................... 7 3.2.1 cooling............................................................................................................................................ 7 3.2.2 appearance.................................................................................................................................... 7 3.2.3 installation .................................................................................................................................... 7 3.2.4 Interface and function is introduced ......................................................................................... 7 4 performance.......................................................................................................................................................... 8 4.1 environment.............................................................................................................................................. 8 2 We declare that:
the product is installed with battery separately in the box. The FCC ID label is placed on Mobile Payment Terminal clearly visible to all persons at the time of purchase. the user is cautioned that changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Do not attempt to disassemble the Mobile Payment Terminal and battery by yourself. Non-expert handling of the devices may damage them. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment FCC Radiation Exposure Statement: To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of 20 cm is required between the antenna and all occupational persons, and a minimum separation distance of 20 cm is required between the antenna and all public persons. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. It was required to meet requirement of RSS-Gen Section 7.1.3. 1 Introduction 1.1 Application background Due to the mobile communication network covers not perfect, the remote suburbs highway, cell phone signal existence covered blind spots. Residents drove go out, mobile phone often appear weak signal, the phenomenon such as no signal. In order to solve the problem, the residents used to buying their own cell phone signal amplifier products, local area signal coverage, in order to meet the communication needs. 3 2 System (the) introduction 2.1 System composition and principle block diagram in the paper 2.1.1 Diagram of the system of the Cell phone signal amplifier communication schemes 2.1.2 System principle outlined 1. This product is suitable for WCDMACDMA and GSM type of network 2. Cell phone signal amplifier (and amplifier for synonyms hereinafter referred to as the amplifier), amplifiers, feeder, antenna etc 3. The amplifier's working principle is descending amplifier through the installation in the OUTDOOR antenna base station downline weak signal, and then through the rf feeder will signal is introduced into equipment. Amplifier to the introduction of the weak base station downside signal filter and amplification, and through the INDOOR antenna will enlarge the signal after launch out to meet demand cover 4. Uplink working principle: the amplifier INDOOR antenna to mobile terminal of the uplink signal, through the rf feeder introduced to the equipment. Equipment will be up for filter and amplification signal, and then through the rf feeder connected to the OUTDOOR antenna, the signal will launch out. Return to base station, so as to establish the whole communication links process 4 2.2 The composition and principle block diagram in the paper 2.2.1 The block diagram of 850M UP_LNA filter UP_PA duplexer duplexer DW_PA filter DW_LNA Combiner INDOOR x2 x1 u1 f(x1...xn) Combiner f(x1...xn) u1 x1 x2 OUTDOOR UP_LNA filter UP_PA duplexer duplexer DW_PA filter 1900M DW_LNA The principle diagram amplifier 2.2.2 The principles outlined Mainly by 850 M amplifier and 1900 M two amplifier moduleThe distribution of the method of frequency by close to completeFirst downside (BTS) signals through the OUTDOOR antenna into the method of close Close to 850 M and PCS1900M method of two signals to choose apartAnd then sent into the corresponding amplifier module will ampli Signals into the amplifier moduleFirst after duplex deviceDownlink signal to choose filterEnter LNA (low noise amplifier) preliminary amplificationAnd then after surface acoustic filter filterEnter UP_PA (downside power amplifier) to signal further amplificationAfter double work of choice is again after filteringEnter and method, and then through the heavy start antenna launch out 5 3Function 3.1.1 Rf index Nmber ITEM 850MHz band 1900MHz band Uplink Downlink Uplink Downlink Specification 1 2 3 4 5 6 7 8 9 10 11 12 Frequency Range 824~849MHz 869~894MHz 1850~1910MHz 1930~1990MHz Output Power 192dBm 112dBm 192dBm 102dBm Max .Gain 592dB 622dB Noise Figure 6dB Amplitude ripple 6dB Input V.S.W.R/
Output V.S.W.R 2.0 622dB 592dB 7.5dB 14dB Spurious 9kHz~1GHz -36dBm/100KHz Emission&Output inter-modulation 1GHz~12.75GHz -30dBm/1MHz ZPORT 50 Operable temperature
-30 70 range operating current Operating voltage range Contour dimension 2.5A DC+5~6V 14012222mm 3.1.2 The input and output signal 1. OUTDOOR IN(869~894MHz\1930~1990MHz)INDOOR OUT 2. INDOOR IN(824~849MHz\1850~1910MHz)OUTDOOR OUT 6 3.2 structure 3.2.1 cooling The overall structure and the floor flats and combinationsThe bottomCover for the metal aluminium materialHeat dissipation goodInternal electroplating metal layerCan effective signal, shielding 3.2.2 appearance 3.2.3 installation Add install board, wall hung installation 3.2.4 Interface and function is introduced 1. The indicatorGreen light 2. Status indicatorRed lightWhen the power output full UP850M UP End and the 1900M UP endOr equipment of self-excited will light on 3. Power sourceThe input power 4. Gain selected switchThe switch has three gearH is gap not attenuationL for 20 dB attenuationM for 10 dB attenuation 5. Power amplifier state selector switchThe switch has two gearOn one side is normal mode, On one side is energy-saving modeWhen there is no users will greatly reduce the power consumption of the call 6. USB+5V: Only as the USB interface charging terminal use 7 Power source OUTDOOR Power amplifier state selector switch Status indicator The indicator INDOOR Gain selected switch USB+5V 4 performance 4.1 environment NO. Technology parameters Working temperature Storage temperature Relative humidity vibration Vibration direction
-30~70
-30~70 95%30 10Hz30Hz0.38mm 30Hz55Hz0.19mm Normal work direction impact 6g 8