LED Controllers SR-ZG9101FA-RGBW 09.ZG3FW.04282 Important: Read All Instructions Prior to Installation Function introduction 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller. Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15 seconds timeout, repeat the operation. 12-36VDC Input AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Step 4: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller's menu and can be controlled through controller or hub interface. ZigBee RGBW Receiver Prog. T U P T U O D E L 1/R-
2/G-
3/B-
4/W-
Common Anode output (+) CH 1 (R) output (-) CH 2 (G) output (-) CH 3 (B) output (-) CH 4 (W) output (-) Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity Note: W channel can only be turned on through color temperature control command since Zigbee only has tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels. Product Data No. Input Voltage Output Current Output Power Output Type Dimension (LxWxH) 1 2 3 12-36VDC 12-36VDC 12-36VDC 4CH, 5A/CH 4CH, 0.35A/CH 4CH, 0.7A/CH 240-720W 16.8-50.4W 33.6-100.8W Constant voltage Constant current Constant current 170x53.4x28mm 170x53.4x28mm 170x53.4x28mm ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights W channel can only be controlled through color temperature control command Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white ZigBee end device that supports Touchlink commissioning Supports self-forming zigbee network without coordinator Supports find and bind mode to bind a ZigBee remote Supports zigbee green power and can bind max. 20 zigbee green power remotes Compatible with universal ZigBee gateway products Waterproof grade: IP20 Safety & Warnings DO NOT install with power applied to device. DO NOT expose the device to moisture. Operation 1.Do wiring according to connection diagram correctly. 2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system. ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
4. TouchLink to a Zigbee Remote Step 1: Method 1: Short press Prog button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation. Method 2: Re-power on the device, Touchlink commissioning will start after 15S if its not added to a zigbee network, 165S timeout. Or start immediately if its already added to a network, 180S timeout. Once timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
< 10cm Zigbee Remote ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 4: There shall be indication on the remote for successful link and connected light will flash twice. Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to corresponding remote or touch panel manual to learn how. Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. 3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink. 4) After TouchLink, the device can be controlled by the linked remotes. 5. Removed from a Zigbee Network through Coordinator or Hub Interface From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset. 6. Factory Reset Manually Step 1: Short press Prog. key for 5 times continuously or re-power on the device for 5 times continuously if the Prog. key is not accessible. 9. Learning to a Zigbee Green Power Remote Step 1: Short press Prog. button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Step 2: Connected light will blink 3 times to indicate successful reset. ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Note: 1) If the device is already at factory default setting, there is no indication when factory reset again . 2) All configuration parameters will be reset after the device is reset or removed from the network. 7. Factory Reset through a Zigbee Remote (Touch Reset) Note: Make sure the device already added to a network, the remote added to the same one or not added to any network. Step 1: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Step 4: There shall be indication on the remote and connected light flashes 3 times for successful reset.
< 10cm Zigbee Remote ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to corresponding remote or touch panel manual to learn how. 8. Find and Bind Mode Step 1: Short press Prog. button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 3: Connected light will flash twice to indicate successful learning. Then the remote can control the device. Step 2: Set the green power remote into Learning mode, please refer to its manual. Note: Each device can learn to max. 20 zigbee green power remote. Zigbee Green Power Remote 10. Delete Learning to a Zigbee Green Power Remote Step 1: Short press Prog. button 3 times (Or re-power on the device 3 times) to start delete Learning mode
(connected light flashes slowly), 180 seconds timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Step 3: Connected light will flash 4 times to indicate successful deleting. Zigbee Green Power Remote ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 2: Set the paired green power remote into Learning mode, please refer to its manual. 11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required) Step 1: Short press Prog. button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation. AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Zigbee Remote AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
Zigbee Remote ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it to find and bind initiator, please refer to corresponding remote or touch panel manual. Step 3: There shall be indication on the remote or touch panel that it bind the device successfully and can control it then.
< 10cm TouchLink ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
ZigBee RGBW Lighting Device Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals. Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals. Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals. Note: 1) Each added device can link and be controlled by max. 30 added remotes. 2) Each added remote can link and control max. 30 added devices. 12. ZigBee Clusters the device supports are as follows:
Input Clusters 0x0000: Basic 0x0006: On/off Output Clusters 0x0019: OTA 0x0003: Identify 0x0008: Level Control 0x0004: Groups 0x0300: Color Control 0x0005: Scenes 0x0b05: Diagnostics 13. OTA The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically. Wiring Diagram AC Power 50/60Hz L N G I N P U T 12V/24V/36V CV PSU T U P T U O V-
V+
ZigBee RGBW Receiver Prog. ZigBee RGBW Receiver Prog. 1/R-
D 2/G-
E L 3/B-
4/W-
1/R-
D 2/G-
E L 3/B-
4/W-
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V+
R- R-
G- G-
B- B-
W- W-
Connect with RGBW LED Strip Connect with RGBW LED Strip FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.