Using the System Powar ON/OFF Press the [ 6 1 button on the side of the main speaker or the remote oontrol to power the system ON. When powered ON, the LED light panels will turn on and the speaker will enter Bluetooth pairing mode, automatically re-pairing to any nearby previously-
paired device that has Bluetooth enabled. Press the [ 6 I button on the main speaker or the remote to power the system OFF. Bluetooth Pairing 1. Power the speaker ON. A tone will ba heard. 2. Sat your mobile device to search for Bluatooth devices. Whan it appears, select BSSK9000 from the list of found devices. 3. After a successful pairing, a tone will be heard again, indicating the system is paired. 5. Protect the power cord from being walked on or pinched, particularly at plug outlets, convenience receptacles and the point where it exits the unit. 6. Do not allow cord to touch hot surfaces. Wrap cord loosely around the unit when storing. 7. The unit should be situated froNlr'/ from direct sunlight or heat sources such as radiators, electric heaters, heat registers, stoves, or other units (including amplifiers) that produce heat. Avoid placing an top of stereo equipment that radiates heat. B. Do not overload the electrical outlet. Use only the power source es indicated. 9. Do not carry this unit by its card or use the cord es a handle. 10. Never operate this unit if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, do not attempt to fix it yourself. 11. Ta avoid the risk of electric shack. do not disassemble or attempt to repair the unit. Incorrect repair can cause risk of electric shock or injury ta persons when the unit is used. 12. Do not operate in the presence of explosive and/or flammable fumes. 13. Never remove the plug from the outlet by pulling the power cord. lnsbllllng Ramote B a t t a r l The remote control will already have a CR2025 battery installed, just remove the plastic tab sticking out of the compartment. To replace a battery, remove the compart-
ment from the side of the remote control. Place a new CR2025 battery with the polarity facing up and slide the compartment beck in so that it clips into place. 14 3 FCC Information Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can ba determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected.
- Consult the dealer or en experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Information This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. The LED panel has a single position pin hale that can only be connected to a bracket in a single orientation. The Main speaker panel has a single, central position pin hole and the Secondary speaker panel has multiple position pin hales, and can be connected ta the bracket in any orientation. Note: The main speaker MUST be connected ta the main speaker bracket. The bracket will be marked with a sticker. 1. Connect a panel by placing on the bracket, aligning the position pin and position pin hole then firmly pressing dawn, making sure that
.u thrrHI a m o f t:lipa . , . SIICUNly r:onflflt:t-
" " and in plar:11. 2. Continue connecting the other speaker and light panels. Make sure the unit is completely connected and that ell three metal contact pin sections are fully touching the wall bracket connectors. 3. Once finished, insert the pin of the supplied power adapter into the DC power input jack an the corner of the main speaker. Plug the adapter into an electrical wall outlet. 4 13