Bluetooth Headset SH26 FCC ID:2ABFFSH26 Operation Instructions 1.TO TURN ON:Press and hold the MFB for 4 seconds, the blue indicator will flash fast 5 times. 2.TO TURN OFF:Press and hold the MFB for 4 seconds, the red indicator will flash fast 5 times . 3.TO PAIR:When the headset is off , hold down the MFB Button for 7 seconds and the Blue and Red indicator light will flash quickly and youll hear an audio tone. The headset is ready to connect to the device 4.TO ANSWER A CALL: Short press the MFB button once to answer an incoming call.You will hear an indication tone. 5.TO HANG UP: Short press the MFB button once to end the call. You will hear an indication tone. 6.TO REJECT A CALL:Hold the MFB button for 2 seconds to reject an incoming call. You will hear an indication tone and the call will be ended. 7.TO REDIAL THE LAST NUMBER:In the standby mode, double press the MFB button to redial the last number. 8.TO VOICE TRANSFER:During a call, hold the Vo+ for 2 seconds until you hear a tone. The call will be transferred from your HEADSET to your mobile device. You can repeat the step to transfer to call back to your HEADSET 9.TO MAKE VOICE CALLS:If the voice recognition function is turned on for your device and it is connected to the speaker, you can make voice calls. Heres how:
1) Press Vo+ and Vo- button at the same time, you will hear a tone to indicate that voice function has been activated. 2)Say clearly the name of the person you wish to call.
(dependent on individual phone device) 10.TO MAKE VOICE CALLS: Short press the MFB button to play or pause music . 11. TO PLAY/ PAUSE MUSIC: Press PREV, play PREV song. 12.TO NEXT MUSIC:Press NEXT, play next song. 13. TO ADJUST VOLUME: Short press Vo+button to increase volume, and you will hear an indication tone when increase to maximum volume. Similarly, short press Vo- button to decrease the volume, and also an indication tone when decrease to minimum volume. 14.TO MUTE:While taking a phone call,press and hold Vo- with 3 seconds to mute your MIC,and you can repeat the operation to open the MIC. 15. After you have successfully connected with an Apple devices like iPhone or iPad, you will see a small battery icon indicating the battery level of your headset so you are always ready to party. (only applicable for selected Apple devices) Battery charging and low-voltage alert When connected normally to charge, the red LED is on when charging and Blue LED turns on when charging is complete. This takes 2-3 hours. When the battery is running low, the alert tone sounds and the red LED flashes twice every fifteen seconds.Charge as soon as possible or it will automatically shut down. Charging Charging voltage:5V Charging time: 20.5H Voltage after complete charging:4.104.20V Remarks 1) If headset stand by with paring mode for 5 min and without connection, It will be exit paring mode automatically, also, the device will power off after more 5 min.. 2) Automatic re-connection can happen in the two cases:
a. If headset is turned off, it will connect to the pre-set device automatically when turned on manually. b. When headset disconnects from the device due to an exceeded effective range (normally < 10 meters), it will re-connect to your device if it is back in the effective range within 5 minutes. LED Indicator Status Power on Power off Charging Charging complete Blue LED flashes 5 times with fast Red LED flashes 5 times with fast Red LED lights Blue LED lights Standby Talking BlueLED flashes twice every seven seconds Blue LED flash once every seven seconds Incoming call Blue LED flash once every second Playing music with Bluetooth Blue LED flash once every two seconds Playing music with TF card Blue LED flash once every ten seconds Battery low Pairing mode Red LED flashes twice every fifteen seconds LED flashes in red and blue alternatively This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.