FCC ID: V7TMESH21XEP AXE5700 Whole Home Mesh Wi-Fi 6E System

Quick Installation Guide AX5400 Whole Home Mesh Wi-Fi 6 System AXE5700 Whole Home Mesh Wi-Fi 6E System MX15 Pro/EX15 Pro/MX21 Pro/EX21 Pro

( 2-pack, 3-pack ) Please read this guide before you start with the quick setup upon the first use. You can see the product name and model on the product label. MX15 Pro is used for illustration here unless otherwise specified. The actual product prevails. This guide instructs how to install and connect the device. For more information such as the description of symbols displayed on relevant materials, please visit www.tendacn.com or scan the Product Documents QR code in this guide. Package contents MX15 Pro (3-pack) & EX15 Pro (3-pack) MX21 Pro (3-pack) & EX21 Pro (3-pack) Mesh15XP/Mesh21XEP x 3 Power adapters x 3 Ethernet cable x 1 Quick installation guide x 1 MX15 Pro (2-pack) & EX15 Pro (2-pack) MX21 Pro (2-pack) & EX21 Pro (2-pack) Mesh15XP/Mesh21XEP x 2 Power adapters x 2 Ethernet cable x 1 Quick installation guide x 1 Appearance T E S E R H S E M 3 2 1 r e w o P Reset button MESH button WAN/LAN auto-adaptive port Power jack Button Description MESH MESH button. As a networking button: Press this button on this device for about 1 to 3 seconds. The LED indicator blinks green fast, which indicates the device is searching for another device to form a network. Within 2 minutes, press the MESH button of another device for 1 to 3 seconds to negotiate with this device. As a de-networking button: Press this button for about 8 seconds and release it when the LED indicator blinks red fast. The node is restored to factory settings, and also removed from the network and no longer automatically joins in again. Tips Do not hold down the MESH button for 8 seconds if unnecessary. RESET Reset button. When the device completes startup, hold down this button using a needle-like item (such as a pin) for about 8 seconds, and then release it when the LED indicator blinks red fast. The device is reset successfully. I Connect the primary node II Connect the primary node to the internet

* Choose one device from the kit to connect to the internet as the primary node in the network. Tips If you do not use a modem for internet access, please skip steps 1 and 3. 1. Power off your modem. 2. Use the included Ethernet cable to connect the 1, 2 or 3 port to your modem or the Ethernet jack. 3. Power on your modem. 4. Power on the primary node, and wait until the LED indicator blinks green. Method 1: Setup through Tenda WiFi App 1. Download the Tenda WiFi App onto your mobile device by scanning the QR code or by searching for Tenda WiFi in Google Play or App Store. Then install the Tenda WiFi App. or Tenda WiFi T E S E R H S E M 3 2 1 r e w o P Power outlet T E S E R H S E M 3 2 1 r e w o P Gigabit port Internet Modem(such as optical modem) Ethernet cable or Ethernet jack 2. Connect the mobile phone to the WiFi network of the primary node. The SSID and password can be found on the bottom label of the device. Settings NOVA_XXXX_XX SSID: NOVA_XXXX_XX SSID:

NOVA_XXXX_XX 3. Run the Tenda WiFi App and follow the onscreen instructions to connect the device to the internet. After the device is connected to the internet, its LED indicator lights solid green, and the device has become the primary node in the network. Method 2: Setup through web UI 1. Connect the client to the primary node. Method 1: Connect the wireless client such as a mobile phone to the WiFi network of the primary node. The SSID and password can be found on the bottom label of the device. Method 2: Use an Ethernet cable to connect the computer to the 1, 2 or 3 port of the primary node. Extend network III 1. Place the other devices in the kit within 3 meters from the primary node to power them on. Wait for about 3 minutes. When the LED indicators of these devices light solid green, the networking is successful and these devices become secondary nodes in the network. 3. Power on the secondary nodes again till these LED indicators blink green slowly. The MX15 Pro(3-pack) is taken as an example here. Tips If the LED indicator of secondary node keeps blinking green slowly for more than 3 minutes, relocate the secondary node and move it closer to the primary node. LED indicator Power outlet T E S E R H S E M 3 2 1 r e w o P SSID: NOVA_XXXX_XX SSID:

NOVA_XXXX_XX Settings Wi-Fi Wi-Fi NOVA_XXXX_XX CHOOSE A NETWORK or Ethernet cable LED indicator 2. Start a browser on the client and enter tendawifi.com in the address bar to access the web UI, and follow the onscreen instructions to connect the device to the internet. Tips If you cannot log in to the web UI, refer to Q3 in FAQ. 2. Please refer to the following relocation tips to locate the secondary nodes to a proper position:

Ensure that the distance between any two nodes is less than 10 meters. Keep your nodes away from electronics with strong interference, such as microwave ovens, induction cookers, and refrigerators. Place the nodes in a high position with few obstacles. 4. Observe the LED indicator of the secondary nodes until the LED indicator lights one of the following colors:

Solid green Networking succeeds. Excellent connection quality. Solid yellow Networking succeeds. Fair connection quality. Solid red Networking succeeds. Poor connection quality. 5. If the secondary node's LED indicator lights solid red, relocate it according to step 2 in III Extend network to get an optimal connection quality. Done. To access the internet with:

- Wired devices: Connect to the 1, 2 or 3 ports of your nodes.

- Wireless devices: Connect to your WiFi network using the SSID and password you set. (All nodes share the same SSID and password) If you configure the nodes using the Tenda WiFi App and you want to manage the network remotely, tap on the App home page and use your account to log in. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Operations in the 5.15-5.25GHz band are restricted to indoor use only. This equipment should be installed and operated with a minimum distance 20cm between the device and your body. The mains plug is used as disconnect device, the disconnect device shall remain readily operable. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. Declaration of Conformity Declaration of Conformity Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the device is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://www.tendacn.com/download/list-9.html Operating Frequency:

2.4 GHz: EU/24122472 MHz (CH1-CH13) 5 GHz: EU/51505350 MHz (CH36-CH64) 6 GHz: EU/5945-6425 MHz (CH1-CH93) (Mesh21XEP, MX21 Pro, EX21 Pro) EIRP Power (Max.):

2.4 GHz: <20 dBm 5 GHz: <23 dBm 6 GHz: <23 dBm (Mesh21XEP, MX21 Pro, EX21 Pro) Software Version: V16.03.37. (Mesh15XP, MX15 Pro, EX15 Pro), V16.03.40. (Mesh21XEP, MX21 Pro, EX21 Pro) FAQ Q1: Can I add another new set of nodes to expand my network coverage?

A1: Yes. Try the following solutions:

Tips Please ensure that the new node you want to add has never been used. If not, reset it first. Method 1: Press the MESH button for about 1 to 3 seconds. The LED indicator blinks green fast, which indicates the device is searching for another device to form a network. Within 2 minutes, press the MESH button of another device for 1 to 3 seconds to negotiate with this device.

Method 2: Run the Tenda WiFi App and manage the network, tap on the My WiFi page, and follow the on-screen instructions. Method 3: Log in to web UI of the node, tap on the Network Status page, and follow the onscreen instructions.

Q2: How to restore my device to factory settings?

A2:

When your device is working properly, hold down the RESET button of your device using a needle-like item (such as a pin) for about 8 seconds, and release it when the LED indicator blinks red fast. When the LED indicator lights solid green, your device is reset successfully. Q3: I cannot log in to the web UI by visiting tendawifi.com. What should I do?

A3: Try the following solutions:

If you are using a wireless device, such as a smart phone:

Ensure that it is connected to the WiFi network of the node. Ensure that the cellular network (mobile data) of the client is disabled. If you are using a wired device, such as a computer:

Ensure that tendawifi.com is entered correctly in the address bar, rather than the search bar of the web browser. Ensure that the computer is connected to the LAN port of the node properly using an Ethernet cable. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device is for indoor usage only. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment should be installed and operated with minimum distance 20cm between the device and your body. FCC regulations restrict the operation of this device to indoor use only. (Mesh21XEP, MX21 Pro, EX21 Pro) The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.

(Mesh21XEP, MX21 Pro, EX21 Pro) Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. (Mesh21XEP, MX21 Pro, EX21 Pro) Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Ensure that the computer is set to obtain an IP address automatically and obtain DNS server address automatically. If the problem persists, please reset the node by referring to Q2 and try again. Q4: The device failed to be detected by the Tenda WiFi app upon my first time using the device. What should I do?

A4: Try the following solutions:

1. Ensure that your mobile phone is connected to the default WiFi network of the device. 2.Ensure that the network permissions of Tenda WiFi app is enabled. You can tap Settings > Tenda WiFi to enable it. If the problem persists, please reset the node by referring to Q2 and try again. LED indicator status After the device is powered on for about 40 seconds, the system completes startup. The status of the LED indicator is shown in the following table. LED indicator status Description Solid green Solid yellow Connected to the internet. Networking succeeds. Fair connection quality. Solid red Networking succeeds. Poor connection quality. Blinking green slowly Connecting to other nodes or waiting to connect to other nodes. Blinking green fast Networking by MESH button. Blinking red slowly Failed to connect to the internet. Operating frequency: 24122462 MHz, 51505350 MHz, 57255850 MHz, 5925-7125 MHz

(Mesh21XEP, MX21 Pro, EX21 Pro) NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. Caution:

Adapter Model:

GQ24-120200-AB, GQ24-120200-AG, GQ24-120200-AU, GQ24-120200-AA

(Mesh15XP, MX15 Pro, EX15 Pro) GQ24-120250-AA, GQ24-120250-AB, GQ24-120250-AG, GQ24-120250-AU

(Mesh21XEP, MX21 Pro, EX21 Pro) Input: 100-240V AC, 50/60Hz 1.0A Output: 12V DC, 2A (MX15 Pro, EX15 Pro, Mesh15XP); 12V DC, 2.5A (MX21 Pro, EX21 Pro, Mesh21XEP) Manufacturer: DONGGUAN CITY GANGQI ELECTRONIC CO., LTD

: DC Voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment

(WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. For EU/EFTA, this product can be used in the following countries:

Get support and services Scan the Product Documents QR code to get related documents, such as the datasheet and user guide.

* The product model can be found on the label of the device. Product Documents

(such as datasheet and user guide) Safety Precautions Before performing an operation, read the operation instructions and precautions to be taken, and follow them to prevent accidents. The warning and danger items in other documents do not cover all the safety precautions that must be followed. They are only supplementary information, and the installation and maintenance personnel need to understand the basic safety precautions to be taken.

- The device must be horizontally mounted for safe use.

- Do not use the device in a place where wireless devices are not allowed.

- Please use the included power adapter.

- Mains plug is used as the disconnect device, and shall remain readily operable.

- The power socket shall be installed near the device and easily accessible.

- Operating environment: Temperature: 0 - 40; Humidity: (10% - 90%) RH, non-condensing; Storage environment: Temperature: -40 - 70;

Humidity: (5% - 90%) RH, non-condensing.

- Keep the device away from water, fire, high electric field, high magnetic field, and inflammable and explosive items.

- Unplug this device and disconnect all cables during lightning storms or when the device is unused for long periods.

- Do not use the power adapter if its plug or cord is damaged.

- If such phenomena as smoke, abnormal sound or smell appear when you use the device, immediately stop using it and disconnect its power supply, unplug all connected cables, and contact the after-sales service personnel.

- Disassembling or modifying the device or its accessories without authorization voids the warranty, and might cause safety hazards. Technical Support Shenzhen Tenda Technology Co., Ltd. Floor 6-8, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 Website: www.tendacn.com E-mail: support.nova@tenda.com.cn support.de@tenda.cn support.de@tenda.cn support.fr@tenda.cn support.es@tenda.cn support.it@tenda.cn support.uk@tenda.cn Copyright 2023 Shenzhen Tenda Technology Co., Ltd. All rights reserved. Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to change without notice. UK(NI) V1.0 Keep for future reference.

AXE5700 Whole Home Mesh Wi-Fi 6E System Model: EX21 Pro Power: 12V 2.5A Login address: http://tendawifi.com FCC ID: V7TMESH21XEP SSID: XXXX_XXXX_XX Password: XXXXXXXX MAC: XXXXXXXXXXXX SN: XXXXXXXXXXXXXXXX Indoor Use only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. www.tendacn.com Made in China Add: 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. Importer:

AXE5700 Whole Home Mesh Wi-Fi 6E System Model: Mesh21XEP Power: 12V 2.5A Login address: http://tendawifi.com FCC ID: V7TMESH21XEP SSID: XXXX_XXXX_XX Password: XXXXXXXX MAC: XXXXXXXXXXXX SN: XXXXXXXXXXXXXXXX Indoor Use only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. www.tendacn.com Made in China Add: 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. Importer:

AXE5700 Whole Home Mesh Wi-Fi 6E System Model: MX21 Pro Power: 12V 2.5A Login address: http://tendawifi.com FCC ID: V7TMESH21XEP SSID: XXXX_XXXX_XX Password: XXXXXXXX MAC: XXXXXXXXXXXX SN: XXXXXXXXXXXXXXXX Indoor Use only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. www.tendacn.com Made in China Add: 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. Importer:

--.. /012,%3#4,+5665,$7.89-,..,

&8 !

&8 &

9:.;7 <.+9.(

7&:8 =%(>+

--.. +4?.775.9-,!@,7%3

&8 7)

&8 &

.-::8&-.77--.37:-A.B,

-7C45A.B

D--.:

E#FC66"<.02/#!8.

%8:-.7

<.G5E#DH<EG5DH#EG5D

%-I %- 2&&> JC%<#!"G5E#D

K+

G6G406C06C

&8 !

2 #7

!7 LLLLLLLLLL+

MNOPQR

STURVPWXYZP[\NZ]^^_aYb_OYNc defghijhkklmnopmqrmsrtjuvmrrkiwrxiyvrjzijmsruomsijl{rwu|rvm}

"#$" 4

%&()&(*(+,*-&(./.01-.23/*+2

56789::;3*:<=;>3(:2?@@?3)A:BCDAEBFGEB H:EI3(EBDAEB+JDK;JLK3

%A=BMA=B

-AJBE

%GNO=LKP$

H=W=;=BL=BGXN=;PYYYYYY

QR*S%&T?UV

Z[

?2/:BC6*=;X-:BWJI=BKJE9JKF

\]^_\abcadbefd$"

fe!"d"####

[abg

[h!"

i## ^f"!"

Z#

4d"##$f"effe"$d

!""#\]_\]abab_#d$#

f"#$"f#d"#f"#

jd"#_

T2%A:;K6*=;X-:BWJI=BKJE9JKFk%*-l

d4\mnopqrstuvqwwxyyxqz{y|q}x~xzqusq~qw|}xststuwusxz

!\]_f"#\]_\

^fZ""fe!"ab fd$

f yu{yz}

Z^# f

f

T@T>6@R6@R

%A=B1G=

()(*+,-.//0123+42.15

-.//2552.16047.*28+42.1+1)

9:+,0+42.1;2:252.1

<=>?@+A,+1)B2,,5C.+)-.,0/D2+EB;FGH=I

JKKLMNOPQRSTUVQ!

W.X7./Y4B+Z-.13(*1 X(E[\]^_\]^]^ab]c\^dedfgcdhieahjkllmnoopqrstuvvmwxvynmz{w

|v}~~wvovlw|oomwnnw}~sE

+44(5447+44725Y1)..*633(55.214)(:23(3./,2(524747(.,,.21*(02*(/(145

.+*4G?9.47(--*0,(5.*ID+1)5

! L

--Y;<WB9FG9 W.X7./Y4B+Z-.13(*1

!#L X(E99W9;6W9-@@-@EW;+44(5447+44725,..(*21)..*

+33(55.2143./,2(524747(.,,.21*(02*(/(145.+*4G?9.47(--*0,(5.* 47(?F?'<GF?8D+1)

W725)(:23(4*+15/24.(*5(34*+,)(1524Z2521+33.*)+13(24747(*0,(5.*,. (*21)..*+33(55.2145 F-.14(142.1D+5()*.4.3.,E+5)(/.154*+4()2147(4(54*(.*4E25(*/+1(14,Z

(/D())()2147(372j-B?>G>=@-BI<?I6G9+1)251.47.54

)((1)(14

>61GG+Y9996W*+15/24.(*91:(,.((,(/(147+521.*/+42.12(,)5.*.(*

,2/245.*3.11(34213,2(1450D.*)21+4()(:23(5W7(W921.*/+42.125(/D())()214725

)(:23(521+,5+1)05()4.4(,,47(3.11(34213,2(14550D.*)21+4(47+447(/+W.(*5 2425+,,.()4.4*+15/24W7(*(25+*(0,+4.*Z21.2(,)214725)(:23(5D(+3.1+1)*.D(

*(5.15(*+/(57237)(4+2,54725)(:23(4Z(7(147(3,2(1450D.*)21+4(+55.32+4(54. 4725)(:23(

UN6GHZ PRE-APPROVAL GUIDANCE CHECKLIST 1. Antennas 1.1 Information for all the antennas, i.e., type, gain and relative positions within host, must be included in the filing. Please refer to page6 of MX21V1.0 for antenna specification. Please refer to document EP-2303C106-1 Appendix for Internal Photographs &

MX21V1.0 for the antenna positions. 1.2 Show how the (aggregate, if applicable) antenna gain was computed/measured (as in TCB Workshop Presentation Aggregate Antenna Gain Review, April 2021). Provide equation(s) used to calculate Directional Gain and provide example calculation showing how the DG was calculated with the antenna gain of individual antennas. Provide details (references or attached documents) on how the individual antenna gains were derived, i.e., declared by the host manufacturer, based on data sheet, or measured. Since the CBP needs to detect a small signal, the worst case scenario to consider is when the receiver has the lowest antenna gain. The device has the same maximum antenna gain for each antenna. According to FCC KDB 662911 D01v02r01:

CDD Directional Gain = Antenna Gain + Array Gain, Array Gain = 0 dB for NANT 4;

Beamforming Directional Gain = Antenna Gain + 10*log (NANT/NSS). Please refer to page11 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for detailed above antenna information. 1.3 For conducted test in MIMO cases, show that the testing was done for that path that has the lowest antenna gain. The device supports CDD and not supports MIMO. 2. Contention Based Protocol (CBP) 2.1 CBP testing shall be performed on one channel in each sub-band of operation for both narrowest and widest bandwidths. Please refer to page 233 of BTL-FCCP-4-2303C106 R00_Wi-Fi 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test channel and bandwidth information as follows. The narrowest and widest bandwidths were test for each UNII band. 2.2 Use three separate 10 MHz AWGN signals when testing a 160 MHz channel. The simulated incumbent signal must be a 10 MHz wide AWGN signal Please refer to page 233 of BTL-FCCP-4-2303C106 R00_Wi-Fi 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test summary information. Please refer to page 224~232 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the AWGN signal plots. for the AWGN signal plots. 2.3 Report lowest AWGN signal detectable by EUT Please refer to page 233 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for lowest AWGN signal detectable by EUT. 2.4 Verify that the testing was performed with the AWGN signal set to lowest level (for example,

- 100 dBm) and increased until the EUT detects and stops transmitting. The test was performed with a lowest AWGN signal level and increased until the EUT detects and stop transmission, and the AWGN level of AWGN signal detected (Stop but with Beacon signal) and AWGN level of the stopped transmission are recorded in the report. Please refer to page 233 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 of RF report for the information. 2.5 If conducted measurements are used, the detection threshold needs to be corrected to refer to a 0 dBi gain antenna and include all the applicable losses (cables, etc.). For instance, the report should show (at least): Detection Level = Injected AWGN Power (dBm) Antenna Gain (dBi) +

Path Loss (dB) Conducted test is performed for this device. Please refer to page 33 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test setup diagram as below. Please refer to page 31 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the relevant description. 2.6 Include plots showing EUT has stopped transmitting after detection of AWGN signal. Please refer to page 234~241 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test result. 2.7 Describe whether channel puncturing and/or bandwidth reduction mechanisms supported. The report needs to include a plot as an example for at least one of the AWGN signals used. Not Support. 2.8 If radiated testing is used, show that spot-checks were done to identify which side of the EUT has the lowest sensitivity to the incumbent signal detection, and that side was indeed chosen for the test. Conducted test is performed for this device. 3. Client Device Limitations This device is not a client device. 4. Emission Mask 4.1 Power spectral density suppression complies with 47 CFR 15.407(b)(6). Please refer to APPENDIX F of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test result of Emission Mask. 4.2 If EUT supports OFDMA discuss testing of partial Resource Unit (RU) configurations. In any case the shape of the mask shall be based on full RU. This device supports one configuration only in 802.11ax full RU mode. This information is noted on page 13 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 4.3 OOBE limits only apply outside of the 5.925-7.125 GHz band. All in-band emissions need to meet the channel mask. In case a higher RBW for the in-Band Emissions Mask is used (i.e., a more conservative case) that should be noted. Please refer to APPENDIX F of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-

NII 5, U-NII 6, U-NII 7, U-NII 8 for the test result of in-Band Emissions Mask. 5. Filing 99% of the occupied bandwidth must be contained within all the U-NII sub bands authorized for that equipment class. Please refer to APPENDIX B of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8 for the test result of 99% of the occupied bandwidth. 6. Hearing Aid Compatibility (HAC) Not Applicable. 7. Labelling 7.1 Label showing indoor only for Subordinate and APs. Please refer to the document Label and Label Location. The label showing Indoor User only. 7.2 E-labelling may be acceptable if proper justification is provided Not Applicable. 8. Modular Certifications (when applicable) Not Applicable. 9. RF Exposure 9.1 Demonstrate applicable classification (portable/mobile/fixed) in reference to worst-case scenario use cases The RF Exposure report is BTL-FCCP-5-2303C106 R00_MPE. Page 9 of the report states that this device is a fixed device and the calculated distance is 20 cm. 9.2 Address f > 6 GHz RF exposure via most recent applicable KDB or TCB Workshop procedures. BTL-FCCP-5-2303C106 R00_MPE was used the most recent KDB to count the RF exposure via. 9.3 Address all applicable simultaneous transmission conditions using the compliance condition TER1. The RF Exposure report is BTL-FCCP-5-2303C106 R00_MPE. Page 8 of the report states that the device compliance simultaneous transmission conditions. 10. Security Provide specific exhibit with device security description is required (complying with 47 CFR 15.407(i)) 11. Spurious Emissions Show that measurements are made at the prescribed antenna heights, per KDB Publication 987594 D01, including measurements along all three axes, as per ANSI C63.10. Spurious Emissions test items refer to page 23-26 of BTL-FCCP-4-2303C106 R00_WI-FI 6E U-

NII 5, U-NII 6, U-NII 7, U-NII 8. Spurious Emissions test result refer to APPENDIX D & E of the BTL-FCCP-4-2303C106 R00_WI-FI 6E U-NII 5, U-NII 6, U-NII 7, U-NII 8. All the test is performed according the KDB 987594 and ANSI C63.10 requirements. For spurious emission test, every axis (X, Y, Z) was also verified. The test results shown in the report represent the worst-case emissions.

+%),#- )#& &./ !% )#&0/*#& 12345 6! &7!!*8#

"#!%$9 :70;<=2>

0 )A=1B=1B;=;3

8CA+))*) )#&@) )$&)*D );EF<<1!&G

""H0#I &)"#AJ1K7.@L;<M.D

NOPQROPQSPQTUSPVOQWXWYZVW[\XST[]^_abccdefbg_hifaj_ekeal_b_mblnk_aob_ank_akedegpnk

), qq!( )#&:SrstuSrvwsxyxz{\|sv*#%*G& )?E@E G&)C#*/(#Cq#(**C#), 9#/

C&(""H0ENOPQROPQSPQTUSPVOQWXWYZVW[\XST[ ((q)*)#$ &) & & G&)C#&#!**

), &#&} C)),G &), *)$& ) !!$ 6)&G &$q#) )#&#),(#&(!%*#&#C &}

"#$$**#&B! )q#(&G&/#!/&G),~%q$&)E

SrstuSrvwsxyxz{\|sv ((q)*: *#C), )#C),C!&G#C), qq!( )#&:),#9!G )#&#C),

*G& )?E@E G&)C#*/(#Cq#(**C#), 9#/C&(""H0E

0*G& )?E@E+G&)H&C#$ )#&A

$AK& K(,&#!#G}:H&(

8A==332<==;

+**A<441I !+/:")}#CH&%*)}:"+F<12:?&)@) )*

"#&) ()D*#&A7}L%

.$ !A$}E,%)& %*E(#$

#9))!A7 & G

NOPQROPQSPQTUSPVOQWXWYZVW[\XST[

H&*)+qq!( &)*G& )% SrstuSrvwsxyxz{\|sv 7}L%

?E@E+G&)*G& )%

.)*+,"-/,*0123/423/53/6753.2/898:;.8<956< 7##$%%0=>?@A))$5)B$3C/)<DEED4 )"% ,"-!,"F),#/,"% ,"6&%$&(1 "G ". &",< HD?EHI

2$J-()"K&$* , K)AA)B&"+$)#!(%0

L$)#!(#%($&+&)"07M3HNEE )A2)*O% &>@&=31-%* 5-+#%&",&)"0DPO% IDM3L IPOMIDL$) CP3MIDL$)

5$,#*,$Q05"#,

5 ,

7AAR$%&)"%)K O% IDM3LOMIDL$),"#3MIDL$),$A($&(,AA-S!,AT(+ K)AA)B&"

#&KK$"(0 5 O)#AO% IDM3LOMIDL$),"#3MIDL$),$)"A-#&KK$&"&"*)#A",*<

6,0IEIC>EH>DE

/,*01 ";! 5A+ )"0?=>NHH>IN=HNEU? 3>*,&A0% "-!V"#,<(" 1&",!$0

/(01(234(56783(49:;<&3=

>:;<&3=?&;()@AB?CAB?DB?%EDB>A?FGFHI>FJ0GD%J E445(66)K-LMN::50D:O(5B,0?:JP++P0C1:3861&3=2&3Q:&40?&361&3%765790@1(3R1(30>173&J SPL+S*

%(9N&5(1&)

T5:4294(6957<7:3)EUBS.++/1:N(A:;(V(61/7-M7KB@=6(;

D=<(4(6783&7:3)V(61*PUBTWVU*PT5:WBU*PT5:

X5&34)D(34&

M>>Y%)Z.DVB@A*PUBT

F3N=91&33(N6P[PPO7NN\(26(473]@EJ>:235=9:4(6(N(97:376476&\N(4J

Y^=:21&_(&3=2(67:365(8&547381(&21:57R&7:30<N(&6(4:3:1(67&(:9:3&92601&3a=:2[

@739(5(N=0

ghebid bc"d!effffffffffffffffffffffff jeklmnnmlnmopk qhe !"r"s

)"*!+",-."/012-".3456 -7

89:;<9=>?@AB?@AC@ADC@E?AFGFHIEFJ*GCJ

KK= LMNO44/*C4P"/@&*A4JQ%%Q*B+4-20+ -7, -R4 .*A -0+ -10!/13!*

>+"-S+"-*E+1- JTQM%T$

"3O /"!+ !#

UVK:=DW@T(%%)+4O"?45"X"0+)1N1L@>70!"5 Y;:KZ=X"0+$QW@[\XW$Q[/4\@W$Q[/4

]=C"-.

^88_=(CX@>?$QW@[

abcdefgchiejklmdnoephqirsihetukrmvikikwkikgxtyezuekrvej{b|}~baankphqir 54."0+4,O.-4!"0,664/!".""-4->N>/","-31"0TJ$TTJ&TH?STJ(TJ($TH?SJ

$J- ..1!14-*!+"/","-370"O"3!14-" !,/"10.10 O".71/5P /"4/."13"05 /"!".!4

!+">JC+"6/4.,3!5""!0 OO4!+"//",1/"5"-!006"311".1-[ /!QT@>"3!14-QTJ%( -.-4 34-12,/ !14-34-!/4O0 /"6/41.".!43+ -2"!+"/","-37446"/ !14-04,!01."!+"2/ -!4 3"/!113 !14-4/>46"/ !14-J

&JF-O73+ --"O0QQQP1OO",0".1->DJE4,-!/734."0"O"3!14-10.10 O".J

74,+ " -7,"0!14-0/"2 /.1-2!+" ,!+4/1S !14-*6O" 0".4-4!+"01! !"!434-! 3!,0*

!+ -74,

>1-3"/"O7*

>12- !,/"# A 5"#>+"-I," C"O#ML(TT$(LT(%M

@5 1O#3"/!!"-. J3-

&()*+,-./*+0123*4

567896:;<=>?<=>@=>A@=B<>CDCEFBCGD@G HIIJJ:K$LMN11,@1O,=#>1GP""P?(1*/-(*4)*Q1+>*-(*.-,.0

;(*R(*B(.*GSPL"S!

0N,(

TIUIJ7:AV=S%""&(1N<12W-(&.$M.K=;4-2 X87IJY:W-(!PV=Z[WV!PZ,1[=V!PZ,1

\I:@*+

]55^:_%@W=;<!PV=Z

XJIab\IYIcJ6IJd776I7]efI

I678]edUgXdU8d\IY6IJJ7dI higjklmnI

cJ6IJaII]eJ7f87d6YJJJ7d6

o8dI87Jg

pq41)(r*4s)-.1*-,/,+.*/()(1,.R.1*3N-+1*1(-.101*0)-

(*t41)u

;.*0,N4

;./*), vvvvvvvvvvvvvvvvvvvvvvvv

>2 ;(*F)

@N LK$%SS$!%KS%"wL

=2.N 0,x*+G0*

SHENZHEN TENDA TECHNOLOGY CO., LTD. FCC Software Configuration Control Declaration Date: July 21, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: AXE5700 Whole Home Mesh Wi-Fi 6E System/

Mesh21XEPMX21 ProEX21 Pro Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Shen Yue Title: Engineer Signature of applicant Date: 2023/07/21 FCC Software Configuration Control Declaration Rev1.1