Welcome Guide Wireless Car Charger Mount Screw Knob Air Vent Clip Ball Joint USB-A fast charging port LED indicator USB-A normal charging port Car charger body Negative shrapnel contact Positive shrapnel contact FCC ID Statement Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. EN Contents Compatibility Suitability
(Adjust the Bottom Tray) to Keep Phone and Coil Aligned LED Indicator Instruction Product Overview Assembly And Installation Steps Power On Using Steps Specications FAQ Attention JP LED 03 04 05 06 07 09 11 12 13 15 16 18 19 20 21 22 24 1 DE Inhalt Kompatibilitt Anpassungsfhigkeit Anbringen Ihres Smartphones Status-LED Produktbersicht Montage und Installationsschritte Kabelloses Laden Ihres Smartphones Anbringen Ihres Smartphones Spezikationen FAQ Achtung 26 27 28 30 32 33 34 35 36 37 39 41 42 43 45 47 EN Compatibility Please notice: Make ensure your phone could be compatible with Qi wireless charging before using this wireless car charger. It is necessary to adopt the QC 3.0 car charger to connect the wireless car charger mount. Smart Mobilephone Car Charger Output Power Qi-Compatible Phones
+
5V 2A
=
=
5W 7.5W The suitability of phone case If the phone case is as the follows, it will not suitable for this product: Too thick (4mm / 0.16 inch) or with a bumpy surface; comes with medal, magnet, a ring shape mount, medal sticker attached, credit card, Popsockets etc. 9 V 2 A 12V 1.5A Quick Charge 3.0 iPhone XS Max, iPhone XR, iPhone XS, iPhone X, iPhone 8 Plus, etc Samsung Galaxy S10+, S10e, S10, S9+, S9, Note 8, S8+, S8, S7 Edge, S7, etc. LG G7 ThinQ V30V30S ThinQ V35 ThinQ, V40 ThinQetc.
+
+
9 V 2 A 12V 1.5A Quick Charge 3.0
=
10W Suitability The suitability of car air vent Cannot support intensive, circular or special-shaped air vent.
(Adjust the Bottom Tray) to Keep Phone and Coil Aligned Please adjust the base according to the guide below. Align the center of your phone to the wireless charging area of the car bracket. (Located by the wireless charging icon). LED Indicator Instruction Product Overview 6.4 6.1 5.8 4.7 6.4 6.1 5.8 4.7 6.7 6.4 6.1 5.8 4.7 6.7 6.4 6.1 5.8 4.7 Blue: Charging Red: Not Charging Scale Phone model 4.7 5.8 6.1 6.4 6.7 iPhone 8 etc. iPhone X / XS / Galaxy S10e / S7 / S6 / S6 edge etc. iPhone XR / Galaxy S10 / S9 / S8 / S7 edge /
Note 5 etc. iPhone XS Max / 8 Plus / Galaxy S10+ / S9+
/ S8+ etc. Galaxy S10 5G / Note 9 / Note 8 etc. Charging Status LED Indicator Display Power on Standby Charging The red and blue indicators flash alternately then go off. Indicator goes off. The blue indicator on. Foreign Object Detector The red indicator flashes. Silicone Pads Release Button Wireless Charging Sensing Area Adjustable Bottom Tray Press Position Clamp Arms USB-C Charging Port Fixed Nut 2 3 4 5 6 7 Assembly And Installation Steps 1. Unscrew the xed nut completely, let the connecting ball through the xed nut (The thread must face the groove) and push it to the groove in the back of the car mount rmly. 3. Twist the screw knob to adjust the opening of the clip to t the air vent. Power On 1.Plug TORRAS fast charge car charger adapter into cigarette lighter outlet. Using Steps 1. Pressing the quick release button, the clamp arms will automatically pop open. 2. Tighten the xed nut. 4. Find a suitable place to insert the wireless charger car mount. Tighten the screw knob to x the car mount and adjust the angle of the car mount to t your sight. 2. Plug the charging cable USB-A into the car charger adapter to fast charge port. Plug the charging cable USB-C into the mount. 6.7 6.4 6.1 5.8 4.7 2. Place your phone into the holder and press the clamp arms towards each other. Then press the clamp arms with a little force again until you hear the click. Your phone will be secured by the arm clamps. Specications Product Name Wireless Car Charger Mount Model Input Output CTVK09 5.0V 2.0A / 9.0V 2.0A/
12V 1.5A 5W/7.5W/10W Charging Distance
(4-6)mm Working Temperature 32-1130-45 Applicable Model Compatible with iPhone, Samsung, LG, Moto etc.
( 4.5-6.7 inches phone) Product List Wireless Car Charger Mount 1, Charging cable 1, Air vent clip x1, Fast Charge Car Charger 1, Manual book 1 Product Name Fast Charge Car Charger Model Size Net Weight Input Output Working Temperature CCVZ18
(612630)mm 21g 12V-24V USB1: 3.6-6.5V 3A, 6.5-9V 2A, 9-12V 1.5A USB2: 5V 2.4A 32-1130-45 The parameters above are derived from the laboratory of TORRAS. The actual parameters would be different because of products and other factors. The image shown here is indicative only. FAQ 1. No charging or slow charging a. Please check the status of the LED light, the blue light indicates charging and the red light indicated low power. b. Adjust the bottom adjustment according to the manual guide, this ensures that the center of the phone is aligned with the charging area sensor. c. For 10W, 7.5W fast charging you must use with the QC 3.0 car adapter. Do not connect directly into the in car USB port. d. Check your phone case whether contain metals and magnets, they'll block wireless charging. Please remove all metals, magnets, credit cards and popsocket on phone/phone case. e. Ensure your phone case is thinner than 4MM otherwise the phone will not be able to wireless charge. f. If the temperature is too high the charging speed will be slow. Turn off navigation and other unused apps whilst also lowering the temperature of the car with the air conditioner. g. Always use the original power cable supplied with the car mount, this will ensure fast and safe charging. Note: In order to realize the fast charging function, the charging cable USB-A must be plugged into the fast charge port (the blue one). 2. Ventilation and air vent tting It is only suitable for horizontal and vertical air vent. For more details please refer to Ventilation and air vent tting. 3. Phone case tting It is suitable for phone cases thinner than 4mm. Please do not use phone case with medal, credit card, back-clip battery, medal rings, medal stickers, popsocket or phone cases with mounts (such as UAG) etc. For more details please refer to Phone case tting. 4. Working temperature The perfect temperature would be 0-45. The mount cannot function properly when the temperature is too high or too low. Attention 1. Prevent the mount from falling off. 2. Please do not expose to liquids. 3. Please do not disassemble. 4. Please use this product in within the recommended temperature. When its too hot in summer or too cold in winter, turn on the AC, wait till the car temperature changes to use this product. 5. Please install the car mount in a suitable place before starting the journey, do not operate and adjust the car mount while driving. 6. Do not install the car mount in a position that interferes with the operation of the airbag or hinders driving. 7. Keep the car mount away from children. 8 9 10 11 12 13 14 15 16 JP Qi QC3.0
//
LED Qi-Compatible Phones
+
5V 2A 5W 7.5W
=
=
4mm / 0.16 inch/
////
PopSockets 6.7 6.4 6.1 5.8 4.7 6.7 6.4 6.1 5.8 4.7 Scale Phone model 9 V 2 A 12V 1.5A Quick Charge 3.0 iPhone XS Max, iPhone XR, iPhone XS, iPhone X, iPhone 8 Plus, etc Samsung Galaxy S10+, S10e, S10, S9+, S9, Note 8, S8+, S8, S7 Edge, S7, etc. LG G7 ThinQ V30V30S ThinQ V35 ThinQ, V40 ThinQetc.
+
+
9 V 2 A 12V 1.5A Quick Charge 3.0
=
10W 17 18 19 20 1. 3. USB-C USB-A USB-A LED 2. 4. 21 22 23 24 25 6.4 6.1 5.8 4.7 6.4 6.1 5.8 4.7 LED FOD 1. a led b c 10W7.5WQC 3.0 USB d popsocket e 4MM f g 2. 3. 4MM popsocket UAG 4. 0-45 1. 2. 3. 4. 5. 6. 7. DE Kompatibilitt berprfen Sie vor der Verwendung dieses Produkts, ob Ihr Smartphone mit der Qi-Technologie fr kabelloses Laden kompatibel ist. Bitte verwenden Sie das QC 3.0-
Autoladegert, um die Kfz Induktive Ladestation anzuschlieen. Smartphone Kfz-Ladegert Ausgangsleistung Anpassungsfhigkeit Anpassungsfhigkeit des Lftungsschlitz Kompatibel mit horizontalen und vertikalen Lftung sffnungen; bogenfrmige oder einziehbare Lftung sffnungen werden nicht untersttzt. Qi-Compatible Phones
+
5V 2A
=
=
5W 7.5W Nicht kompatibel mit solchen Handyhllen Von der Verwendung extrastarker Smartphone-Schutzhllen
(dicke4mm / 0.16 Zoll) oder Schutzhllen mit Magnet-bwz. Metalleinsatzen wird abgeraten,da diese die kabellose Ladefunktion beeintrachtigen konnen. 9 V 2 A 12V 1.5A Quick Charge 3.0 iPhone XS Max, iPhone XR, iPhone XS, iPhone X, iPhone 8 Plus, etc Samsung Galaxy S10+, S10e, S10, S9+, S9, Note 8, S8+, S8, S7 Edge, S7, etc. LG G7 ThinQ V30V30S ThinQ V35 ThinQ, V40 ThinQetc.
+
+
9 V 2 A 12V 1.5A Quick Charge 3.0
=
10W 4.7 5.8 6.1 6.4 6.7 iPhone 8 etc. iPhone X / XS / Galaxy S10e / S7 / S6 / S6 edge etc. iPhone XR / Galaxy S10 / S9 / S8 / S7 edge /
Note 5 etc. iPhone XS Max / 8 Plus / Galaxy S10+ / S9+
/ S8+ etc. Galaxy S10 5G / Note 9 / Note 8 etc. CCVZ18
(612630)mm 21g 12V-24V USB1: 3.6-6.5V 3A, 6.5-9V 2A, 9-12V 1.5A USB2: 5V 2.4A 32-1130-45 TORRAS 1. 1. 2.USB-AQC3.0 USB-C 6.7 6.4 6.1 5.8 4.7 2. CTVK09 5.0V 2.0A / 9.0V 2.0A/
12V 1.5A 5W/7.5W/10W
(4-6)mm 32-1130-45 iPhoneSamsung, LG, Moto Qi 4.56.7 1,1 1 x1 1 USB-AQC3.0 26 27 28 29 30 31 32 33 34 Anbringen Ihres Smartphones Passen Sie die Haltefe der Halterung entsprechend dem Handymodell an, das der Tabelle unten entspricht, um die Mitte des Handys(der drahtlose Ladebereich des Mobiltelefons) auf den Ladeerkennungsbereich des Wireless Charger Autos (in der Nhe des drahtlosen Lademusters der Halterung) auszurichten. Status-LED Produktbersicht Screw Knob Air Vent Clip Montage und Installationsschritte 1. Schrauben Sie die Befestigungsmutter ab und fhren Sie die Verbindungskugel durch die Befestigungsmutter. Bitte beachten Sie, dass die groe ffnung der Mutter zum runden Loch zeigt. Und schieben Sie es fest in das runde Loch auf der Rckseite der Halterung. 3. Drehen Sie den Schraubknopf, um die ffnungsgre des Chips an die Dicke der Abluftkanal anzupassen. Kabelloses Laden Ihres Smartphones 1. Stecken Sie das Autoladegert in den Zigarettenanznder
-Sitz ein und schalten Sie das Ladegert ein. Anbringen Ihres Smartphones 1. Durch Drcken des Schnellspanners werden die Klammerarme automatisch geffnet. 6.4 6.1 5.8 4.7 6.4 6.1 5.8 4.7 6.7 6.4 6.1 5.8 4.7 6.7 6.4 6.1 5.8 4.7 Blau: Aufladen Rot: Fehler Signal Skala Ideal fr 4.7 5.8 6.1 6.4 6.7 iPhone 8 etc. iPhone X / XS / Galaxy S10e / S7 / S6 / S6 edge etc. iPhone XR / Galaxy S10 / S9 / S8 / S7 edge /
Note 5 etc. iPhone XS Max / 8 Plus / Galaxy S10+ / S9+
/ S8+ etc. Galaxy S10 5G / Note 9 / Note 8 etc. Status LED-Anzeige A Stromversorgung angeschlossen. Das rote und blaue Licht leuchtet auf und erlischt dann. Standby Die Kontrollleuchte erlischt. Mobilgert wird geladen Das blaue LED-Licht ist immer an. Metall oder andere Fremdkrper erkannt Das rote LED-Licht blinkt. Silikon-Pad Entriegelungsknopf Induktiver Ladebereich Verstellbare Haltefe Finger position Ball Joint Klammerarm USB-C
-Anschluss Befestigungsmutter USB-A QC 3.0 Port LED-Anzeige USB-A Port Ladegert Gehuse Negativer -Splitter kontakt Positiver-Splitter kontakt 2. Ziehen Sie die Befestigungsmuttern fest an. 4. Whlen Sie einen geeigneten Ort zum Einsetzen des drahtlosen Autoladegerts. Ziehen Sie den Schraubknopf an, um die Autohalterung zu befestigen. Passen Sie den Winkel der Halterung an die Sichtlinie 2. Stecken Sie die USB-A-Schnittstelle des Ladekabels in die Schnellladeschnittstelle QC 3.0 des Autoladegerts und stecken Sie die USB-C-Schnittstelle in den Ladeanschl uss der Halterung, um die Stromversorgung einzuschalten. 2. Legen Sie Ihr Handy in den Halter und drcken Sie die Klammerarme gegeneinander, bis Sie das "Klicken"
hren. Ihr Telefon wird durch die Armklemmen gesichert. 6.7 6.4 6.1 5.8 4.7 Besondere Note: Sie mssen die USB-A-Schnittstelle des Ladekabels an die Schnellladeschnittstelle QC3.0 (Blaue quadratische Schnittstelle) des Autoladegerts anschlieen, um die Schnellladefunktion zu erreichen. Spezikationen Produktname WIRELESS CAR CHARGER MOUNT Modell Input Output CTVK09 5.0V 2.0A / 9.0V 2.0A/
12V 1.5A 5W/7.5W/10W Ladeentfernung
(4-6)mm Betriebstemperatur 32-1130-45 Anwendbares Produktliste Kompatibel mit iPhone, Samsung, LG, Moto usw.
(4,5-6,7 Zoll Mobiltelefon) Wireless Charger Auto 1, Ladekabel 1, Belftungsclip x1, Saugnapfhalter x1, 3M Armaturenbrett Pad1, Bedienungsanleitung 1 35 36 37 38 39 40 41 42 43 Produktname WIRELESS CAR CHARGER MOUNT Modell Gre Nettogewicht Eingang Ausgang Arbeitstemperatur CCVZ18
(612630)mm 21g 12V-24V USB1: 3.6-6.5V 3A, 6.5-9V 2A, 9-12V 1.5A USB2: 5V 2.4A 32-1130-45 Die obigen Parameter stammen aus dem Labor von TORRAS. Der tatschliche Parameter wrde sich aufgrund von Produkten und anderen Faktoren unterscheiden. Das Foto ist fr referenz, beziehen Sie sich auf das produkt. FAQ 1. Nicht laden oder langsames Laden a. Bitte berprfen Sie den Status der LED, blaues Licht bedeutet Laden, rotes Licht bedeutet nicht Laden. b. Stellen Sie die untere Haltefe gem der manuellen Anleitung ein, um die Smartphone-Zentrale und den drahtlosen Ladeerfassungsbereich ausgerichtet zu halten. c. Der 10 W/7,5 W Schnelllademodus muss mit dem QC 3.0 Autoladegert verwendet werden, um eine ausreichende Leistung zu gewhrleisten. Schlieen Sie es nicht direkt an die USB-Schnittstelle im Auto an. d. Bitte berprfen Sie, ob das Handy Metall enthlt. Verwenden Sie auf der Rckseite des Handys keine Metallringe, Metallplatte, Kreditkarten, Popsocket usw. e. Das kabellose Laden passt sich an die Handyhlle mit einer Dicke von weniger als 4 mm an. f. Die Ladegeschwindigkeit wird niedrig wenn die Temperatur zu hoch ist. Schalten Sie die Navigation aus, wenn der Akku leer ist, und reduzieren Sie die Temperatur im Auto. g. Verwenden Sie fr ein schnelles und sicheres Laden das mitgelieferte Originalladekabel. 2. Ventilation and air vent tting It is only suitable for horizontal and vertical air vent. For more details please refer to Ventilation and air vent tting. 3. Phone case tting It is suitable for phone cases thinner than 4mm. Please do not use phone case with medal, credit card, back-clip battery, medal rings, medal stickers, popsocket or phone cases with mounts (such as UAG) etc. For more details please refer to Phone case tting. 4. Working temperature The perfect temperature would be 0-45. The mount cannot function properly when the temperature is too high or too low. Achtung 1. Nicht fallen Lassen. 2. Nicht zerlegen. 3. Keinen Flssigkeiten aussetzen. 4. Das Produkt sollte nur fr Umgebungen mit moderaten Temperaturen eingesetzt werden. Sowohl an heien Sommertagen als auch kalten Wintertagen bitte schalten Sie die Klimaanlage ein und warten Sie, bis die Temperatur im Autoinneren angemessen ist, bevor Sie dieses Produkt verwenden. 5. Nicht whrend der Fahrt installieren. 6. Montieren sie die autohalterung nicht an einem ort, der die fu-Nktion des airbags und die fahrt beeintrchtigt. 7. Halten sie die autohalterung von kindern fern. FCC Statement This device complies with part 18 of the FCC Rules. Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and
(2) this devicemust accept any interference received, including interference that may cause undesired operation. Changes or modifications not explicitly approved by the partyresponsible for compliance could void the user's authority tooperate this equipment. Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Increase the separation between the equipment and any other radio device. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Facebook: @Andobil Twitter: @Andobil Google+: Andobil LinkedIn: Andobil Email: support@andobil.com Web: www.torraspower.com LANHE GROUP CO., LTD. SHENZHEN TORRAS TECHNOLOGY CO., LTD. ADD : 17F, BLOCK C, ZHANTAO TECHNOLOGY BUILDING, MINZHI ROAD, LONGHUA DISTRICT, SHENZHEN Shenzhen TORRAS Technology Co., Ltd. All Rights Reserved. Made in China Simplicity For Life 44 45 46 47 48 49 50 TS-CTVK09 TS-CTVK09-(VIC)++
60110 mm 2019.01.27 105 41++++