FCC ID: 2A5RQ-S661LS Mobile Phone

Explosion diagram specification 1 3 5 7 9 11 13 15 17 19 21 CTP LCM ASSEMBLY F CAM RUBBER RECEIVER F CAM COP FOIL LCM WATERPROOF RUBBER R MAIN CAM CON FOAMS FM SUPPORT MYLAR FM CAM FF 8M R VICE CAM RUBBER UP FRAMEWATERPROOF MYLAR 23 R VICE CAM LENS 25 MC SCREW SILVER GIUE 27 BAT COVER ASM 29 MACHINE SCREW BLACK 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 FRONT SHELL ASSEMBLY FRONT CAMERA REC CON FB MAIN PCB BAT FPC CONN RUBBER R CAM CON FB 8W FM CON FOAMS FP SEAL SILICONE LOOP CAM FF 8W UP FRAME ASM R MAIN CAM LENS R VICE CAM LENS2 CARD HOLDER R CAMDECO ASM SPK FRAMEWATERPROOF USB RUBBER SPK FRAME ASM 31 33 35 MOTOR SPK 37 FPC SIDE KEY 39 MYLAR EAR PHONE RUBBER NFC ANT COAXIAL CABLE PCBA SUB BAT 32 34 36 38 40 Know your phone 1. Front camera 2. Volume + key 3. Volume - key 4. Power key SIM/SD card installation 1. Power off mobile. 2. Refer to the following picture for SIM / SD card installation. Charging the phone You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). 1. Please remind the front and back of the plug. 22.. Use only TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty. FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of limits are designed to provide the FCC Rules. These reasonable protection against harmful interference in a residential installation. installed and used This equipment generates uses and can radiate radio frequency energy and, in if not instructions, may cause harmful accordance with the interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

If Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR Information Statement Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the phone transmitting at its highest certified power in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be level tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 1.141W/Kg and when worn on the body, as described in this user guide, is 0.788 W/kg (Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 0.788 W/kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RFexposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on FCC ID: 2A5RQ-S661LS Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protection for the public and to account for any variations in measurements. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. that do not meet Operating SystemAndroidTM Android is a trademark of Google LLC.

V | M O Q Modelo: S661LS TELEFONO CELULAR IIA Bateria:XXXX IMEI:XXXXXXXXXXXXX LA sees 2arewx2 S/N: XXXX NOM a) HECHO EN CHINA EEE oe SOILS aR AFUE VO.1 2022/03/14

SHENZHEN TRANSCHAN TECHNOLOGY LIMITED DATE :2022-9-21 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A5RQ-S661LS Product Name: Mobile Phone Request for Short-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.:

Test Setup Photos External Photos Internal Photos The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public.

<Signature>

Name LI LI Title Manager Company SHENZHEN TRANSCHAN TECHNOLOGY LIMITED