power on / off blue: normal red: abnormal DC jack charging indicator
(red: charging green: charging finished) lateral inlet for the safety rope bottom power switch USB socket anti-droping sensor blue: good status red: abnormal Device Cable Put the clean mop the the pad flatly dont make the mop all wet, and do not spray on the upper part of the robot. 5-6 clean water on the mop. Please red green Cleaning path by pressing X1 button of remote 1. Put the product at the center of glass where is far away from the window frame, press the start button, the product will automatically move downward and upward to detect the friction, then move to the left frame of glass and consequently move upward to the top left corner. 2. After reaching the top left corner, it will start to clean the glass by moving the N-shaped curve from top to bottom. 3. The robot will stop nearby the starting place when finish cleaning work. Cleaning path by pressing X2 button of remote 1. Put the product at the center of glass where is far away from the window frame, press the start button, the product will automatically move downward and upward to detect the friction, then move to the left frame of glass and consequently move upward to the top left corner. 2. After reaching the top left corner, it will start to clean the glass by moving the N-shaped curve from top to bottom. 3. The robot arrived at the top right corner when finished N-shape cleaning, then move in Z-shape curve from top to bottom. 4. The robot will stop nearby the starting place when finish cleaning work. Blue lamp: normal Red lamp: abnormal Indicator(on the handle and the bottom) Meaning Remark Speaker / Alarm alarm every 0.2s always alarm red lamp is always on red lamp is always on no input from adaptor air leakage stop alarming when adaptor is connecting to electricty stop alarming when no air leakage repeat alarming alarm 1 time when blue lamp binks blue lamp flashes 1 time and red lamp flashes 1 time gyroscope sensor error alarm 1 time when blue lamp binks blue lamp flashes 1 time and red lamp flashes 2 times barometer error repeat alarming alarm 1 time when blue lamp binks blue lamp flashes 1 time and red lamp flashes 3 times 2.4 G remote error repeat alarming alarm 1 time when blue lamp binks blue lamp flashes 1 time and red lamp flashes 4 times alarm 1 time when blue lamp binks blue lamp flashes 1 time and red lamp flashes 5 times alarm every 0.2s and repeat 3 times red lamp flashes every 0.2s and repeat 3 times alarm 1 second and stop alarming alarm every 1s and repeat 3 times alarm 0.1s
/
/
/
no safety rope robot cannot move due to too much friction fan calibration failure (too slippery) arrives at the frame when use remote control it finished cleaning work press the button of robot and remote normally don't repeat this glass is too slippery glass is too slippery finshed N-shape or Z-shape cleaning path valid press Model no. WA6 1.46kg Battery lasting time 20mins 90W Suitable for cleaning area 60 x 40 cm Size 248 x 248 x 95 mm FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.?
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.