WA7 Contents Product Introduction Accessories Installation Instructions 1 2 3 4 5 6 7 8 8 9 Operation Instructions & Attentions Path Planning Instructions Meanings of LED Indicator Lamp & Voice Remote Control Instructions Basic Parameters Troubleshooting Safety Precautions Failure List 10 Water plug Functions of the Key Short press it to Switch On/Off when the device is working, and recovery regular suction power when it is standby with small suction. When the device is working, long press the key to turn to standby mode with small suction power. When the device is standby, long press the key to operate the track so that users can clean it. Status indicator Blue lamp: Normal Red lamp blinks: Abnormal if the device is working Red lamp: low power when device is standby. Cable & Safety rope Vvoice guide Lateral side Power Switch USB Port Bottom Status indicator Blue lamp: Normal Red lamp blinks: Abnormal if the device is working Red lamp: low power when device is standby. Drop sensor Device with cable and safety rope 2 1. Please ensure that safety rope has been firmly fastened on a strong object. 2. Insert the frame extending line to the end of the adapter an tighten them. 3. Stick the white surface of the cloth to the bottom of the machine and keep it flat to avoid air leakage. 4. Put clean water into the water tank
, and put back the silicon plug. Be sure to use the original cloth,otherwise, the machine performance will be affected Open the bottom main switch and place the machine in the center of the window
(avoid getting too close to the frame). Make sure the machine is attached to the glass and release the hand. Press the button to start the machine. When the machine finishes cleaning the window and stops working, hold the safety rope in one hand and press the round button until the Suction de-
creases.Put it on the glass again and the machine will automatically absorb it. Please turn off the main switch at the bottom of the machine and unplug the power after use. clean water on the mop. Please he mop all wet, and do not spray on the track.In standby mode, press dont make t and hold the round key for the track to rotate automatically, and wipe the dirt on the track surface with a clean wet cloth. 5-6 Pay attention to the cloth should not be too wet, dirty cloth is recommended to clean and dry before use. Please use original cloth, non-original cloth will affect the machine performance. Turn on the bottom power switch When the machine finishes cleaning the window and stops working, hold the safety rope in one hand and press the round button until the suction decreases.Then take off the machine. In case of loss of remote control turn off the bottom power switch. Clean Path One Time Please put the machine on central position of glass and launch it. After exploring downwards and towards to the left of glass boundary from current position, it will move to upper left corner and start to wipe from top-down N-shaped path. At each corner, please strictly follow the principle of Firstly go forwards and then fallback while applying both wiping-omission resistance and double-overlapping modes. Automatically return to starting position after cleaning. Clean Path Two Times Continue to secondly wipe the zigzag from left to right after completion of wiped path in previous time. And automatically return to starting position after cleaning. Status indicator Blue lamp: Normal Red lamp blinks: Abnormal if the device is working Red lamp: low power when device is standby. LED Indicators and Definition LED Light & Sound Definition Solution 3 Dripping Sounds Cleaning Completed Normal Audible Feedback Red Light Flashes or Light on
Dripping Cycle Blue Light with Dripping Sound
Red Light Repeated Flashing Cycle Not Plugged-in Power Source Check if power source has been well plugged in. Check the power of built-in batteries Air Leakage Check air leakage. Hardware Self-testing alarm Please Contact with Customer service Machine movement abnormality Slippery Check if wiped surface has appeared excessive water spots or oil stains.
*To prevent misoperation , press pause key between instructions Sprayer On / Off Clean twice (in N shape and Z shape) Dry mopping Voice guide On / Off Wet mopping Model Rated Voltage Rated Power Battery Capacity Size Power-off adsorption time Suitable for cleaning area Volume of water tank WA7 24V 90W 650mAh 228*228*80mm 20min 40*60cm ml 1. When the status indicator flashes red with continuous short dripping sound, please check the following faults. Whether power cord plug appears loose or damaged, resulting in power failure or poor contact;
Whether glass or rag is too moist, causing extreme small friction;
Whether viscous object on glass has caused excessive friction of rag;
Whether cleaning cloth has been installed in place without leakage appearance;
Whether the machine has been put on uneven surface, causing leakage phenomenon;
Whether the suction port has been blocked 2. When the status indicator flashes red and blue alternately with a warning sound, it will indicate that the machine stays abnormal. Please refer to LED Indicators and Sound Definitions for further disposal. 3. If the machine does not smoothly move, please replace another clean rag. 4. If the machine completes entire window but fails to automa-
tically stop moving, please press pause button to remove it. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.