FCC ID: 2A442-BM3380G-H Video Encoder

H.265 HEVC/H.264 AVC/MPGE4 FHD Video/Audio Live Encoder Manual 1.Interface Power: DC 9-12V 1A ANT: HG WIFI HDMI IN: HDMI Video Input Port Power: Power Light(Red) Reset:Recovery to Default setting LAN: Lan Status Light(Green) LAN: 1000M Ethernet Port Video: Video Signal Light(Blue) WIFI:it is AP when it is blink,it is connected it is always bright. Instructions A. Power ----9-12 V/DC 1A;

B. Reset----- it is used to reset the equipment; after the equipment is started, press the button for 10 seconds, the equipment IP is recovery to the default IP, 192.168.1.168. C. Video input --- it is used to input high-definition HDMI D. LAN ---- 100M or 1000M Ethernet connection. 2.Specification Input Video Encoding Bitrate HDMI resolution ratio 1920x1200_60P,19201080_50/60P,19201080_50/60i, 1.4 HDMI HDCP 1280720_50/60p 720x576i/p 720x480i/p. H.265 HEVC or H.264 AVC Profile 4.2 16kbit/s32Mbit/s Bitrate control GOP CBR/VBR Adjustable Audio:

Encoding Bitrate Bitrate System:

Network Stream Re-Sampling rate 44100/48000 AAC AAC+ AAC++ MP3 MP2 AC3 G.711A/U 48K64K96K128K160K192K256K Sampling precision 24 bit 64Kb/s~384Kb/s 100M/1000M Base-T Ethernet /WIFI 2.4G UTP,HTTP,FLV,HLS,RTSP,RTMP RTP UDP(Multicast,Unicast) and ONVIF Configuration interface WEB operation interface or CGI Command Updating Software update General Size Net Weight 89*103*29mm 0.3KG Temperature range

-20~55(workable) Power supply 9-12V/1A or 5V/2A Power consumption 5W 3. System Setting 3.1 Reset there is a RST hole on the front panel which is used to conduct initialization reset for the high-definition encoder. When the equipment is powered on, press the button and hold for 12 Seconds, when the power light is off, release the button, and all the parameters will be initialized. The initialized IP is 192.168.1.168. 3.2 Computer IP Address Setting 3.3 Open IE Explorer Computer IP can be set as 192.168.1.*. Note: anyone from 1254, except for 168 Fill http://192.168.1.168 to address bar, Default user name: admin Pass: admin 3.4 Status Display 3.4.1 status: when there is video input, it will display resolution of the input, and if there is not status info,input is not correct, please check your video source or video cable. 3.4.2 main stream : it shows main Stream Encoding Type,Resolution,Bitrate and access address 3.4.3 Sub stream: it shows Sub-Stream Encode Type ,Resolution Bitrate and access address 3.3.4 Preview:

a.Click Preview ,it will play stream in browser b.open VLC software to play stream default http stream address:http://192.168.1.168/0.ts default rtsp stream address:rtsp://192.168.1.168/0 4. Network Setting 4.1 Ethernet Port Instructions: in terms of IP address of the equipment, the factory default is 192.168.1.168. If you forget the IP address after modification, you can reset the equipment by pressing the rest button for 12 seconds when the equipment is powered on, and restore the factory default ip. 4.2 WIFI/AP SETTING 4.2.1 AP Mode APAccess Pointmode is default wireless status. Default AP name is AP_Encoder_XXXX,you can sercah hotspot on smartphone or laptop.Default pass is 12345678. Wifi band supports 2.4G/5.8G Wifi channel: if wireless transmit is jam,you can try to swtich channel You also can check ap information on status page. 4.2.2 WIFI Mode Select WIFI mode,you can click Refresh to scan hotspot after reboot Fill correct hotspot name and pass and wifi ip.Click Apply botton,reboot You will check the connection information on status page. If the wifi level is under 60%,please check environment,it is better to visual range away from router. 5. Main Stream Encoding Setting 5.1Encoding Setting of Main Stream 5.1.1 Encoding Type: H.264 or H.265 or Mjpeg 5.1.2 Encode level: baseline profile / main profile / high profile 5.1.3 Encoding frame rate: 5-60 framesit can output 60p When Input is 60p) 5.1.4 Bitrate control: VBR(quality priority) and CBR(bandwidth Priority) 5.1.5 GOP: 30 5.1.6 Encoding size: 1920x1080, 1680x1050,1280x720, 1024x576,850x480,720x576, 720x540,720x480,720x404,704x576,640x480,640x360,608x488, 544x480,480x480,480x384,480x360,480x320,480x272,480x720,400x320

,400x224,352x480,352x228,320x256,320x240,320x180,240x180,176x 144 5.1.7 Video bit rate: 16-32000K 5.2 Main Stream Protocal Setting UTP protocol(Private) ,Default address http://192.168.1.168/0.utp HTTP protocol,Default address http://192.168.1.168/0.ts HLS protocol,Default address http://192.168.1.168/0.m3u8 FLV protocol,Default address http://192.168.1.168/0.flv RTSP protocol,Default address rtsp://192.168.1.168/0 RTMP pull stream address:

Default address rtmp://192.168.1.168/live/0 default port :1935 RTMP push stream address:

rtmp://ip:port/xxx/xxx or rtmp://user:pass@ip:port/xxx/xxx RTMP default port: 1935 Multicast protocol,Default address UDP://@238.0.0.1:1234 Unicast protocol,Default address: UDP://@192.168.1.50:1234 (Note:192.168.1.50 is received device) 5.3 OSD Setting 5.3.1 Zone 1-4,you can enable max to 4 image or txt Text, support English/number Character Image, support 24bit BMP file ,less than 500KB,transparency color is R:241 G:241 B:241 5.3.2 X coordinate: the left and right positions displayed by 0-1920 text. Y coordinate: the up and down positions displayed by 0-1080 text. 5.3.3 font: the size of 8-72 text display in the display screen. 5.3.4 Alpha: 0-128 , transparency 5.3.5 Logo: select logo files 5.4 Sub Stream Encoding Setting Note: the setting method is as same as that of main stream 6. Instructions for Youtube Streaming 1.Open live streaming page on Youtube 2.Create a live stream channel 3.Copy rtmp address from Youtube The whole address(part 1+part 2) is rtmp://a.rtmp.youtube.com/live2/87gg-dtd0-7atc-8zwu 4.Paste whole rtmp address into encoder Paste whole rtmp address Enable it Click Apply botton 7. Instructions for Facebook Streaming 1.Open live streaming page on Youtube 2. Copy rtmp address from Facebook The whole address(part 1+part 2) is rtmps://live-api-s.facebook.com:443/rtmp/143998560119176?s_bi=1&.DIGXA Paste whole rtmp address Enable it Click Apply botton 8. Audio Encoding Settings Audio Bit rate: 48K, 64K, 96K, 128K, 160K, 192K and 256K Audio type: AAC,AAC+,MP3, MP2,AC3,G711A,G711U Audio resample: 44100,48000 9. System Settings 9.1 User name and password change 9.2 Software upgrade 9.3 System settingsDevice reset and initialization default settings This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm etween the radiator & your body.

Shenzhen Unisheen Technology Co.,LTD. Add: Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua District,Shenzhen City,Guangdong Province,China(PRC) Date: 2022-3-4 FCC ID: 2A442-BM3380G-H Dear Sir/Madam, We, Shenzhen Unisheen Technology Co.,LTD. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: Video Encoder Model no.: BM3380G-H, BM3380G-S, BM3350B-W5-H, BM3350B-W5-H-N, BM3350B-W5-S-N, BM3380B-W5-H-N,BM3380B-W5-S-N, FHDEncoder, NDISRTEncoder Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jiabao Tang/Boss Shenzhen Unisheen Technology Co.,LTD. Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua District,Shenzhen City,Guangdong Province,China(PRC)

+8613554907166 Allen@unisheen.cn

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2022-3-4>

Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2A442-BM3380G-H Model name BM3380G-H For the product stated above, we request that the following information be held confidential;

Exhibits Short-Term Confidentiality Long-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jiabao Tang/Boss Shenzhen Unisheen Technology Co.,LTD. Innovation&Technology Rm506,Hombo District,Shenzhen Rd,Longhua Province,China(PRC)

+8613554907166 Allen@unisheen.cn Industrial Park,Qinning City,Guangdong

Shenzhen Unisheen Technology Co.,LTD. Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua District,Shenzhen City,Guangdong Province,China(PRC) Date: 2022-3-4 FCC ID: 2A442-BM3380G-H Model Number: BM3380G-H To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Shenzhen Unisheen Technology Co.,LTD., declare that this EUT (FCC ID:

2A442-BM3380G-H) doesnt have Ad Hoc mode function on non-US/Canada frequencies. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jiabao Tang/Boss Shenzhen Unisheen Technology Co.,LTD. Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua City,Guangdong Province,China(PRC)

+8613554907166 District,Shenzhen Allen@unisheen.cn

Shenzhen Unisheen Technology Co.,LTD. Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua District,Shenzhen City,Guangdong Province,China(PRC) Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

2022-3-4 We, Shenzhen Unisheen Technology Co.,LTD. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2A442-BM3380G-H including the signing of all documents related to these matters. effect as acts of our own. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jiabao Tang/Boss Shenzhen Unisheen Technology Co.,LTD. Rm506,Hombo Innovation&Technology Industrial Park,Qinning Rd,Longhua District,Shenzhen City,Guangdong Province,China(PRC)

+8613554907166 Allen@unisheen.cn