Package Includes 1 x ANC Headphone 1 x Micro-USB Cable 1 x AUX Cable (3.5mm) 1 x User Manual Overview of the Headphone Active Noise Cancelling Wireless Headphone User Manual 1. 2. 3. 4. 5. 6. 7. 8. 9. ANC On/Off Switch ANC LED/Indicator Volume up/Next track BT On/Off, Play/Pause Volume down/Previous track Power/Pairing/ChargingLED Indicator Micro USB Charging Port Auxiliary Input Jack Microphone Charging 1. Before rst time use, fully charge the built-in battery 2. Plug the small end of the USB cable into the USB charging port on the left earcup. Plug the other end into a USB wall charger or computer that is powered on. LED Indicator Blinking Red Solid Red Red light off Battery Status Need to charge ( charge<10% ) Under Charging Full charged Note: When the battery charge <3%, the headphone will power off automatically. Power On Press the Play/Pause button until you hear a voice saying Power on and the LED indicator light is ashing blue (fast the rst time, then slowly). Power Off Press the Play/Pause button until you hear a voice saying Power off and the LED indicator light ashes red once. (If you are playing music when switching the power off you will hear a descending tone.) Bluetooth connection 1. Press the Play/Pause button and keep it pressed in when the voice says Power On. 2. Keep pressing the Play/Pause button until you hear a voice saying Ready to pair and the LED indicator light is ashing red and blue fast. 3. Go to the Bluetooth settings on your mobile device. Search and select Eartrons PRO from the list. 4. Once your device is paired with the headphones, a voice says Connected and the LED indicator slowly ashes blue. Note: When power is switched on (by pressing the Play/
Pause button until a voice says Power on and the LED in-
dicator starts ashing blue), the headphones will automat-
ically reconnect to the last mobile device it was connected to. (A maximum of 8 paired devices can be memorized.) To save power, the headphones will automatically shut down after 10 minutes in pairing mode if no devices are paired. Music Control Play / Pause Volume Up Volume Down Next track Previous track Click Click Click Press and Hold Press and Hold Speakerphone (in Bluetooth Connection) Answer an incoming call Click Reject an incoming call End the current call Redial last-called number Press and Hold Press and Hold Click Listening music from external audio source 1. Power on the headphone. 2. Using the AUX Cable(3.5mm), connect your external device to AUX-in port on headphone. 3. It will automatically turn to AUX-in mode. Note: Under AUX-IN mode, headphone buttons and speakerphone function are not workable. Noise cancelling function You can use the noise cancelling function with or without power on. Slide the ANC button to turn on/off the noise cancelling function. Note: If the headphone battery is depleted, you cannot use noise cancelling. Troubleshooting Cannot power on: Charge the headphone and make sure it has enough battery charge. No Sound: Make sure the music volume is at audible level on both your device and headphone. Make sure your device is successfully paired with the headphone, the LED indicator turn solid blue. Poor sound quality: Move the device closer to this head-
phone or remove any obstacle between them. Cannot connect with the device: Please check:
The Bluetooth device supports A2DP prole The headphone is within 1 Om from the device. The headphone is in pairing mode, the LED indicator blinking blue and red. Specications Bluetooth Version: 5.0 Support: A2DP V1 .2, AVRCP V1 .4, HFP V1 .6, HSP V1 .2 Wireless working range: 10 meters Bluetooth transmitter frequency: 2.402-2.480GHz Bluetooth transmitter modulation: GFSK Driver Unit: 40mm (32ohm, 20mW) Frequency response: 20Hz-20kHz Audio-SNR@1 KHz = 93dB Mic-SNR@1 KHz = 92dB Active noise reduction: 20dB @ 20Hz-1 kHz (MAX) Battery type: Li polymer (3.7V/520mA) DC input voltage/current: 5V 0.25V I 0.5A Playtime: 19-22 hours (varies by volume level and content) Battery charge time: 2-3 hours Dimensions: 202 x 150 x 71 mm Weight: 254g Caution It is dangerous and illegal (in some jurisdictions) to use headphones when youre driving car, riding bike, motorcycle, or watercraft. Do NOT use the headphone in situations where they might cause distractions or prevent you from hearing warning sounds. Keep the headphone away from re, water, liquids, extreme heat: such like the dashboard of your car on a hot day. Do NOT use this headphone at high volume for extended periods, as this may cause permanent hearing damage or loss. Do NOT drop or knock the headphone on hard surfaces. Do NOT use chemicals or detergents to clean the Do NOT scrape the surface with sharp objects. Do NOT make unauthorized alterations to this headphone. headphone. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.