FCC ID: 2AZHM-C01 C01 Smart Watch

To bring you a better experience, please read these Instructions carefully. Instruction Manual for C01 A. Bind Your Device a. Download and Install the App Download the InxFIT App by scanning the QR code or searching in the App Store. Note: the operating system of your mobile phone needs to meet the following requirements:

iOS 10.0 or Android 6.0 Bluetooth 4.2 1. Scan the QR code below to download the InxFIT App.

(The QR code may be updated.) 2. Open the App Store on your mobile phone, search for InxFIT, and then download the InxFIT App.

(Note: during the binding process, InxFIT will ask you to turn on the Bluetooth of your mobile phone and authorize InxFIT to access the GPS of your mobile phone. For IOS user, when a binding error occurs, please ignore this device in the Bluetooth list of your mobile phone first.) b. Binding Steps 1. On the Home page of the App, click + at the upper right corner and select [Add Device] to search for your watch. Find your watch in the Device List and click it to bind it. 2. On the Home page of the App, click + at the upper right corner and select [Scan]. Then scan the QR code that is displayed on your watch when it is turned on for the first time. If you accidentally exit the QR code page, select [Device][Setup][QR code] to find the QR code. B. Data Synchronization The watch records various data on your activities when it is worn on your wrist. You can synchronize data with the App as follows: start the InxFIT App, and pull down the page to start a data synchronization. The synchronization progress is displayed on the page. Note: please perform a data synchronization at least every 7 days, or the data will be overwritten when the memory is full. C. Instructions for Use a. Charging Diagram Follow the diagram below to connect and charge your watch. We recommend that you charge your watch before turning it on for the first time. b. Wearing and Adjustment 1. Wear Your Watch Leave one-finger gap between the watch and your wrist bone, and adjust the strap to a comfortable length. 2. Replace the Strap Push the push button horizontally to loosen the strap, and then remove the strap. Push button Note: too loose or too tight wearing may affect the accuracy of HR or SpO2 measurement. D. Operating Instructions a. Button Operations Press the button: return to the dial, or switch between the dial and function list. Press and hold the button: turn on/off the device. b. Change the Dial Press and hold the dial screen to display the dial selection list after vibration. Swipe horizontally to select the desired dial, and then click it to apply it. c. Screen Operations Swipe the screen to enter different interfaces as shown below. E. Function Overview 1. Functions Sports / HR / SpO2 / Sleep / Alarm Clock /

Breathing Exercise / Timer / Weather / Music Control / Stopwatch Note: the Weather function needs to be enabled on the App. More details on the functions can be found on the App. a. To start an exercise: click the Sports icon select a sport the exercise data recording will start at b. Control the exercise: press the side button to pause the exercise recording; press the side button again or click [Resume] on the screen to resume the exercise recording. c. Stop the exercise: press and hold the side button to stop the exercise, or click [Stop] on the screen to stop 2. Initiate an Exercise the end of the countdown. the paused exercise. F. Specifications Model C01 Screen type 1.4 inch Battery capacity 250mAh Charging voltage Charging time About 2 hours Bluetooth Version Waterproof level IP68 Charging mode Magnetic charge 5V 4.2 H242 W35.5 D12.1 Operating temperature

-20 - 45 Watch size iOS Andriod IOS 10.0+

Android 6.0+

G. Note: do not wear the device to take a bath, because high temperature or steam may damage the device. H. Cleaning and Maintenance It is recommended to wear and clean the product as follows:

1. Keep the product clean. 2. Keep the product dry. 3. Dont wear the product too tightly. Do not use detergents to clean the device. You can use soap-free detergents. For stains that are not easy to remove, it is recommended to clean with alcohol. I. Safety and Certification (see the certificates) FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC RF exposure statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID2AZHM-C01 Manufacturer's Name: Shenzhen XiaoJu Intelligent Technology Co., Ltd. Address: 708, Block E, E-commerce Incubation Base, Taojindi, Longhua District, Shenzhen, China. C01 Smart Watch Model number: C01 Operating Temperature: -20 C to 45 C This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mmmust be maintained between the users body and the watch, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. This device in compliance with the essential requirements and other relevant provisions of S.I. 2017 No. 1206. All essential radio test suites have been carried out. The device complies with RF specifications when the device used at 0mm form your body. This device in compliance with the essential requirements and other relevant provisions of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091). All essential radio test suites have been carried out. Function Operation Frequency Max RF output power:

Limit 2402~2480MHz _1.50 dBm 20dBm. BT DECLARATION OF CONFORMITY I hereby declare that the product Product name: C01 Smart Watch Model name: C01 Series model : N/A Trademark: N/A HW: C01_MB_V11_20211008 SW: V1.08

(Name of product, type or model, batch or serial number) satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body. EN 55032:2015+A1:2020 EN 55035:2017+A11:2020 EN IEC 61000-3-2:2019+A1:2021 EN 61000-3-3:2013+A1:2019 EN 301 489-1 V2.2.3 (2019-11) EN 301 489-17 V3.2.4 (2020-09) EN 62479:2010 EN 50663:2017 EN 62368-1:2014+A11:2017 EN 300 328 V2.2.2 (2019-07)

(Title(s) of regulations, standards, etc.) All essential radio test suites have been carried out. USB Cable No shield 0.65m NOTIFIED BODY: MiCOM Labs Inc Address:

575 Boulder Court, Pleasanton, California 94566 USA Identification Number: AB 2280 MANUFACTURER or AUTHORISED REPRESENTATIVE:

Address:

Shenzhen XiaoJu Intelligent Technology Co., Ltd. 708, Block E, E-commerce Incubation Base, Taojindi, Longhua District, Shenzhen, China. his authorised representative. Point of contact:

Name:Shan Jiang TEL.:18507551729 fax:

(Name, telephone and fax number) 2022-01-17

(Place, date of issue) This declaration is issued under the sole responsibility of the manufacturer and, if applicable,

(Signature) Hardware Engineer

(Name and title in block letters)

C5266091_X10_Ed.1 Shenzhen XiaoJu Intelligent Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AZHM-C01 Date: 1/7/2022 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No No Short-Term Confidentiality No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Shan Jiang Date: 1/7/2022 Title:

1/1

C5266091_X8_Ed.1 Letter of Authorization Company: Shenzhen XiaoJu Intelligent Technology Co., Ltd. Address: 708, Block E, E-commerce Incubation Base, Taojindi, Longhua District, Shenzhen, China. Product Name: C01 Smart Watch Model Number: C01 FCC Identifier: 2AZHM-C01 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Shan Jiang Date: 1/7/2022 Title:

Signature of applicant:

1/1