FCC ID: 2A6EJ-CPE450 wireless bridge

Outdoor CPE

--Quick Installation Guide--

Model: CPE450 Note A. Thank you for order and using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time;

B.The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional. Tech Service Email: support@tomlov.com Contents 1. Get Started to Know Your Wireless Bridge 2. CPE Bridge For Video Transmission Introduction 3.Outdoor CPE Function 4.Outdoor CPE Specification 5. Connection Diagram 6. Digital Display Wireless Bridge Set Up 7. How to Access and Setting the CPE Via PC 8.Bridge Configuration (WEB UI) 9. Field Applications 10.Wireless Surveillance Connection for Elevator Well 11.Tips 01 01 02 02 03 04-05 06-07 09-10 11-12 13 14 1. Get Started to Know Your Wireless Bridge:

Package Included 2 x Outdoor Wireless Bridge 2 x PoE Adapter 2 x Metal Cable Tie 1 X User Manual Note: This wireless bridge is powered by a PoE adapter through a network cable, so does not require a DC power supply. The DC power adapter and cable are not included in the package. 01 2. CPE Bridge For Video Transmission Introduction CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems and so on. CPE Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. At the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment. In addition to helping you in remote monitoring, wireless bridges can also help you extend the network signal to warehouses, barns, garages, and other buildings near your home. 3.Outdoor CPE Function:

1. Long-distance 5.8G wireless transmission equipment 2.Support point-to-point, point-to-multipoint mode 3.Transmission distance up to 3km(Barrier-Free) 4.WDS networking mode, video network dual compatible. 5. Dialing to set the transmitter and receiver, and also support the PC to modify the IP settings. 6.Dynamic MIMO power saving mode (DMPS) and automatic power-saving transmission (APSD) 02 4.Outdoor CPE Specification Model: CPE450 Master control AR9344 DRAM DDR2 64MByte FLASH8MByte Wired Interface10/100Mbps LAN*2 CPE Transmission rate: 300Mbps (not network rate) Transfer method: Direct Sequence Spread Spectrum (DSSS) Modulation: OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK Network StandardIEEE802.11n,IEEE802.11a ,IEEE802.3u Supporting agreement: CSMA/CA TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,N-

DIS4,NDIS5 Frequency Range: 49006100MHz Power consumption: 3W Power scheme: POE 24V 1A Antenna gain: 14DBi Management settingsWEP managementTelnetSerial EncryptionWEP encryption 64/128bits, WPA, WPA2, 802.1x Operating temperature-3065 5. Connection Diagram:

5.1 . Transmitting Side:

03 5.2. Receiving Side:

6. Digital Display Wireless Bridge Set Up:

*It is strongly recommended to pair the wireless bridge in this way. The digital display bridge is simply connected by dialing. After setting Bridge 1 and Bridge 2 to A and B mode, set the two bridges to the same number1,2,3

...F through the reset button, then the two bridges can be automatically connected without using a computer for IP setting. The dialing settings are only connected using a point-to-point bridge, which is not suitable for point-to-multi-

point connections. 6.1 Connection Diagram:

04 6.2 Before connecting the power supply, move the bridge 1 to the A end through the A-B button, and the bridge 2 moves to the B end through the A-B button, the A end represents the receiving mode, the B end represents the transmitting mode; The bridge 1 and the bridge 2 are respectively set after A and B. Connect the bridge to the power supply, the digital display shows L and flashes, and the L disappears to indicate that the configuration connection is successful. 6.3 The reset button to set the led digital display, click once the startup configura-

tion status, continue to click, the number will increase, can be continuously increased. Assume that a pair of bridges with a number of 3 is configured After bridge 1 set to 3, after the bridge 2 set to 3, first the LED light will flash, then "L" flashes to indicate the application is being configuration, please be patient, When "L"

flashes, it will become the number "3", and the number "3" will continue to flash until the bridge 1, bridge 2 is connected after the success, the LED display 3 is always on, not flashing, indicating that the bridge 1 and bridge 2 has been successfully networked. 6.4 LED Indication Chart:

WLAN After the bridge is connected successfully, the WLAN light will be on, not connected the WLAN light will not be lit. LAN1/LAN2 The data connection is successful, the LED light is on, otherwise, it is not bright. PWR LED LED LED Power indicator, the LED is on after the power is connected Digital display LED display "H" indicates manual configuration status Digital display LED display "L" and flashing indicates settings status Digital display LED flashing indicates edit the config or conne cting Point Light A, B status lights, lighting is B mode, no lighting is A mode. RST RST Click once, the LED display number increases, looping from 0, 1, ..., F. Press over 10s, release the "reset" button, the system automatically restarts 05 6.5 LED Number & IP Chart:

LED A IP B IP 2.4G ID 5.8G ID 0 1 2 3 4 5 6 7 8 9 a b c d e f 192.168.255.100 192.168.255.200 192.168.255.101 192.168.255.201 192.168.255.102 192.168.255.202 192.168.255.103 192.168.255.203 192.168.255.104 192.168.255.204 192.168.255.105 192.168.255.205 192.168.255.106 192.168.255.206 192.168.255.107 192.168.255.207 192.168.255.108 192.168.255.208 192.168.255.109 192.168.255.209 192.168.255.110 192.168.255.210 192.168.255.111 192.168.255.211 192.168.255.112 192.168.255.212 192.168.255.113 192.168.255.213 192.168.255.114 192.168.255.214 192.168.255.115 192.168.255.215 0 1 2 3 4 5 6 7 8 9 10 11 13 96 50 55 0 165 161 157 153 149 48 44 40 36 140 132 124 116 108 100 7. How to Access and Setting the CPE Via PC Step Description:

Step 1. Use a PoE adapter to power the wireless bridge through a network cable. Pay attention to the "PoE" and "LAN" ports marked on the PoE adapter, and power is supplied by POE instead of a DC power interface. Step 2. Use a network cable to connect the CPE "LAN" port, connect the network cable other ends to the PoE Adapter "POE" port, use another network cable to connect to the "LAN" port of the PoE adapter, and connect the other end of the network cable to the computer's "LAN" port. 06 Step 3. Find the number of the Wireless Bridge CPE digital display tube. For example, the number is 1 and the CEP is the A master bridge, then the IP of this CPE is 192.168.255.101; if the CPE is the B slave bridge, then the IP address of the CPE is 192.168.255.201.There is a table corresponding to a number and IP in the manual Step 4. Very important step: Modify your computer's IP address, change your computer's IP address to 192.168.255.xxx(192.168.255.xxx cannot be the same as the IP of the CPE), make your computer's IP and the bridge's IP address be on the same network segment so that you can access them. Please refer to the manual to modify the computer IP address step or Google searches how to modify the computer IP address, it is very simple. Step 5. After you modify your computer's IP address, you open the computer browser and enter the IP address of the wireless bridge to access. For exam-

ple, enter 192.168.255.101 to access. Step 6. Enter the account password "admin/admin" to access, and set after successful access. 7.1 How to Configure Your PC IP As 192.168.255.xxx:

a. Find the network icon in the lower right corner and click Open Network and Internet Settings. 07 b. Select Ethernet and Click the Change Adapter Option. c. Find the network connection you are using and right click on Properties. d. Double-click the IPV4 setting, select the IP address below, enter the IP and confirm. e. Configure your PC IP as 192.168.255.xxx (xxx is a figure 2-254), note that the set PC IP cannot be the same as the IP of the CPE. 255 255 08 8.Bridge Configuration WEB UI Note: Before configuring the Bridge IP, AP Configuration, Client Configuration, make sure that the PC and CPE are properly connected and that the PC IP is configured. 8.1 Computer Setup Debug Connection Diagram:

8.2 Configure Bridge IP:

Please assign a different IP address to each CPE under the same local area network for easy management. 09 8.3 Wireless Receiver ModeReceiving Point Select "A(Master)" under the "Mode", then select Matching IDSuch as

"64(5320Mhz)" The matching IDs of A(Master) and B(Slave) must be the same. Create an easy-to-remember name for your wireless network in Host-

name. See figure below 8.4 Wireless Transmission ModeTransmission Point Select "B(Slave)" under the "Mode", then select Matching IDSuch as

"64(5320Mhz)" The matching IDs of A(Master) and B(Slave) must be the same. Create an easy-to-remember name for your wireless network in Host-

name. See figure below WEB UI Diagram:

10 CPE Connection Diagram:

9. Field Applications 9.1 Point to Point Connection:

11 9.2 Point o to t Multi-Point Connection:

9.3 Multiples Clients Connection:

12 10.Wireless Surveillance Connection for Elevator Well:

13 Network dingram(3) Point-to-point Wireless Network Coverage Extend the network to warehouses, barns, and garages near your home CPE A CPE B Router Internet Computer Router Router device (AP mode) 11.Tips:

1. The installation of this device requires some network knowledge. If you can't install it, please let us know or contact a professional. If the product is dam-

aged or missing accessories, please let us know to reissue a new set. This CPE cannot directly expand the WiFi range for you. If you have any questions, you can free feel to let us know via Amazon or Email, we will quickly respond and help you solve questions. 2. The wireless transmission speed between 2 bridges max is 300Mbps. The highest wire network speed that can be achieved max is 100Mbps. Cannot provide up to 300Mbps wired network speed, because the LAN port of the wireless bridge is a 100M port. 14 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Shenzhen Yazhou Shang Technology Co., Ltd. Agent Authorization Company: Shenzhen Yazhou Shang Technology Co., Ltd. Address: No. 502, Building 120, Shangmeilin New Village, Meilin Street, Futian District, Shenzhen Product Name: wireless bridge Model Number(s): CPE450 CPE451, CPE71C, CPE58G, CPE180, CPE8881, CPE-XXXX Product Description: wireless bridge We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Title:

FU JIN Manager Date: 2022/04/09 Company: Shenzhen Yazhou Shang Technology Co., Ltd.

Shenzhen Yazhou Shang Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022/04/09 Subject; Request for Confidentiality FCC ID: 2A6EJ-CPE450 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Software Security Descriptions In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: FU JIN Title: Manager

Shenzhen Yazhou Shang Technology Co., Ltd. FCC Software Configuration Control Declaration Date: April 14, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: wireless bridge / CPE450 Regarding FCC Country Code Selection guidelines identified in KDB 594280. All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: FU JIN Title: Manager Signatureof applicant Date: 2022/04/13 FCC Software Configuration Control Declaration Rev1.1

Shenzhen Yazhou Shang Technology Co., Ltd. Model Difference Product description: wireless bridge Model name: CPE450 CPE451, CPE71C, CPE58G, CPE180, CPE8881, CPE-XXXX Trade Name: N/A FCC ID: 2A6EJ-CPE450 All the model are the same circuit and RF module, only for model name. Regards Sincerely Clients signature:

Clients name / title : FU JIN Contact information / address: No. 502, Building 120, Shangmeilin New Village, Meilin Street, Futian District, Shenzhen,China