FCC ID: 2AXY5-M13 2-in-1 Magnetic Wireless Charging Pad

M13 Preface:

Dear customers, thank you for purchasing our products. In order to understand the product further. Please read this manual carefully before use. We wish you a pleasant experience!

3 2 Specifications Input: 12V 1.5A 1: Phone output: 15W Max/Earphone output 3W Max 2: Watch: 3W Max 3.Input interface: USB-C Compatible Devices Indicator light description When the power is turned on, the blue indicator light is on

(off within 2 seconds), and it enters the standby mode;

When the watch is charging, the blue light will turn on and off after 20 seconds;

When the phone is charging, the blue light will turn on and off after 20 seconds;

When charging the TWS headset, the blue light will turn on and off after 20 seconds;

The light does not indicate when your device is fully charged When two devices are charging at the same time, the blue light indicates that there are charging prompts on both sides Q&A:

Q:Why is there heating in the charging of wireless charging inductive products?

A:During the charging process, there will be a certain loss of magnetoelectric conversion, which will be converted into heat, causing the mobile phone and charger to generate heat, which is a normal phenomenon. Suggestions:

When the device is fully charged, disconnect it from charging in time to avoid a long cycle of charging, which may lead to continuous 1 4 2-in-1 Magnetic Wireless Charging Pad User Manual 1 2 3 4 Product input interface Mobile phone/headphone charging position Watch charging position Indicator light iPhone13Pro Max/13por/13/13mini/12Por Max/12por/12/12mini/

When the wireless charger output is abnormally charged or foreign objects are heating of the device and charger;

Apple Watch 7/6/SE/5/4/3/2 Airpods/Third Generation/Pro/3/2 detected, the blue light keeps flashing. It is recommended to stop running the background software when charging the phone. Using instructions How to solve abnormal charging:

Please confirm whether your mobile phone has wireless charging function before use;

Check whether the phone deviates from the wireless inductive Power connected ,the device enters the standby state;

charging area of the charger;

Place the Apple Watch in the Magetic charging area to conduct Whether a non-metallic protective case is used for charging mobile wireless charging;

phones, and the thickness of the protective case is recommended Put the mobile phone that supports wireless charging on the not to exceed 4mm;

corresponding charging area for wireless charging. When metal objects touch the charging area, the charger will Put the TWS headset that supports wireless charging on the automatically identify and provide power off protection. corresponding charging area for wireless charging. When the temperature of the charger is too high, it will automatically start the protection.Please unplug the power supply first and use it after the charger recovers the temperature. Safety Notes Use indoor or under dry environment, avoid placing or using in the environment of high temperature, humidity, strong static electricity and strong magnetic field;

For your safety, please do not use wet hand plug and unplug electrical appliances;

. Avoid putting it in a place easily accessible to infants and children;

Do not use the product if it is contaminated with water or dirt;

Non-professional personnel are not allowed to open and repair without authorization. FCC Warning RF exposure statement:

Phone:

This device complies with part 15 of the FCC Rules. Operation is subject to This device was tested for uncontrolled environment operations. the following two conditions: (1) this device may not cause harmful interference, To comply with RF exposure requirements, a minimum separation and (2) this device must accept any interference received, including interference distance of 20cm must be maintained between the users body and the product. Radiated H-Field

-17.8dBuA/m(@10m) TX/RX Frequency Range 110-148kHz(Only for EU&UK) The equipment complies with IC Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body. that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible Declaration of Conformity Shenzhen Yifeng Intelligent Technology Co., Ltd. 10th Floor, Building 2, Chaxi, Zone B, Huafeng First Science Park, for compliance could void the user's authority to operate the equipment. Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd. declares that the Hangcheng Street, Gushu, Baoan District, Shenzhen, China. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes:

Watch:

Radiated H-Field

-17.8dBuA/m(@10m) TX/RX Frequency Range 110-148kHz(Only for EU&UK) 115-205kHz(Only for FCC&IC) NOTE: This equipment has been tested and found to comply with the limits for product type M13 is in compliance with following Regulations: Radio Equipment a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The are designed to provide reasonable protection against harmful interference in Restriction of the Use of Certain Hazardous Substances in Electrical and a residential installation. This equipment generates, uses and can radiate radio Electronic Equipment Regulations 2012. The full text of the UK declaration frequency energy and, if not installed and used in accordance with the of conformity is available at the following internet address:https://www.YFZN.com/

IC Caution:

Radio Standards Specification RSS-Gen, issue 5 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Cana das licence-exempt

(1) Cet appareil ne doit pas causer d'interfrences.

(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Radiated H-Field

-24.24dBuA/m(@10m) TX/RX Frequency Range 300-350kHz instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. This device was tested for uncontrolled environment operations. To comply RSS(s). Operation is subject to the following two conditions:

with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the users body and the product.

(1) This device may not cause interference. Declaration of Conformityvv

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd.declares that the product type M13 is in compliance with Directives 2014/53/EU & 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address:https://www.YFZN.com/

Dclaration d'exposition RF:

L'quipement est conforme la limite d'exposition aux radiations de la IC tablie pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 10 cm entre le radiateur et votre corps.

Shenzhen Yifeng Intelligent Technology Co., Ltd. C5266091_X10_Ed.1 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AXY5-M13 To Whom It May Concern, Date: 10/10/2022 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Ning Liu Date: 10/10/2022 Title: Manager 1/1

C5266091_X8_Ed.1 Letter of Authorization Company: Shenzhen Yifeng Intelligent Technology Co., Ltd. Address: 10th Floor, Building 2, Chaxi, Zone B, Huafeng First Science Park, Hangcheng Street, Gushu, Baoan District, Shenzhen, China. Product Name: 2-in-1 Magnetic Wireless Charging Pad Model Number: M13 FCC Identifier: 2AXY5-M13 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Ning Liu Date: 10/10/2022 Title: Manager Signature of applicant:

1/1