FCC ID: 2AHI4-BTP-BD2A Joystick

BTP-BD2A P5 Button testing Thank you for purchasing our product. Before using this controller, please read the user manual carefully. After reading the manual, please keep it with reference.

USER MANUAL Thank you for purchasing our product. Before using this product, please read the user manual carefully. After reading the manual, please keep it with reference. P1 Overview

Included

(picture1)

(picture2) 1. Choosing the gamepad icon (as picture1 shows) and clicking the right button of mouse to enter the GAME CONTROLLER SETTING(as picture2 shows) 2. Choosing the Properties in the interface of GAME CONTROLLER SETTING P6 Button testing

(1) Checking the joysticks in the area of X axis/Y axis: swing the joysticks optionally and observe that if the testing area of X axis/Y axis shows corresponding.

(2) Checking the LT/RT button in the area of Z axis:

pressing the LT button, the Z axis goes right, pressing the RT button ,the Z axis goes left.

(3) Checking the other buttons in the area ofButtons:-

pressing the A/B/X/Y buttons and so on respectively, the red lights go on correspondingly in the interface of testing. Controller X 1 Receiver X 1 Charging Cable X 1 USER Manual X 1 Warranty Card X 1 2

(picture3) Testing the buttons in the interface of 3. Properties to check the buttons work or not.

as picture3 shows P2 Hiighlights P7 State & Recharging 1.XD4 engineplaying games once it connects. 2.Easeful & accurate D-PAD and Joystick, brings users fantastic game experience. 3.Research and development of BFM mode for Android by BETOP, supports to play the newest games of Android and the devices of Android 4.0 and above. 4.TURBO-Repeating function Setting: In any mode, pressing any buttons and TURBO to realize the repeating function with corresponding buttons. Canceling: In any mode, pressing the button which has been set and CLEAR , it could cancel the repeating function with corresponding buttons. Low battery When the controller is using, LEDs flash sostenuto;

Shutdown Controller is on and not connected for 30 seconds, or connecting with no operation for 5 minutes, it would be shutdown automatically;

Recharging Connecting the controller and PC or DC charger with Charging Cable, if battery is full, LEDs will keep on;

Specification NAME Model number Platform Weight Power supply P8 Warranty Guide BETOP BD2A GAME CONTROLLER BTP-BD2A PC,Android,PS3 About 220g Built-in lithium electricity Dear customer: thank you for purchasing our product, when you use this product, if you meet any questions or quality problems, you can connect with us as follow :

1.Call us : 400-096-3918, service time: 9:30-18:00 2.Send an e-mail to 4006754300@b.qq.com 3.Leave a message on the our website : www.betop-cn.com The following warranty regulations is according to the Three guarantees Free returnrepairing or replacement is available within 7 days of invoice bcause of product quality problem. Free repairing or replacement is available within 15 days of invoice bcause of product quality problem. Free repairing is available within one year of invoice bcause of product quality problem. Payment repairing if beyond the warranty period.( Warranty period: one year ) NoteThis warranty guide is not suit for suspend production. Out of warranty 1.Without invoice or receipt issued. 2.The invoice or receipt issued description inconformity with the product. 3.The brittle label was broken or altered 4.Beyond the warranty period. 5.The malfunction and damaged caused by incorrect use, the unauthorized repairs and alteration. WWW.BETOP-CN.COM LOGO Button P3 LAYOUT BACK Button D-PAD TURBO Button Left Joystick Left LED Right LED Action Button LB/LR Action Button X/Y/A/B Mode Switch Button Right Joystick

How to use

Connecting When users plug the receiver into the devices USB port, and press the LOGO button, controller will be activated and connect the devices automatically. Once the controller is connected with the device, the LEDs will keep light. If users want to switch different mode, it would press the LOGO button for about 5 seconds to switch when the controller is connected successfully with devices.(Notice: Partial devices should be connected with OTG cable.) Connecting devices Mode LED indicate PC360 mode

(Default) Left LED keep light PC PC mode

(Simulative mode) Right LED keep light PC mode

(Digital mode) Right flash snowly Android BFM mode PS3 PS3 mode Left&Right LED keep light According to the PS3 setting keeps light FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. FCC ID: 2AHI4-BTP-BD2A

== BEITONG BEITONG BAT 2 WIRELESS GAMEPAD Nes Cae Rm cul n a ae eT aCe) Pee eee ele a ee oe ee ee COATES Sms) fac) ella ae Oh RUC er DOr ea orcas) ede Uno

@ CO Pc360 mode me Meurer clan ee ee BU ele Mel 3130-112-300 D12117009026 PN: BD2A-AOO 1 1 I I I China '

I

, pe CT) IV UQEUITORE AVA see, T20J70003094 HaNo0/t

Shenzhen Yuejiang Technology Co., Ltd Agent Authorization Company: Shenzhen Yuejiang Technology Co., Ltd Address: Floor 9-10, Building 2, Chongwen Garden, No. 3370 Nanshan iPark, Liuxian Avenue, Nanshan District, Shenzhen City, China Product Name: Joystick Model Number(s): BTP-BD2A We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Sinks. Lhe Date: 2021/11/17 Name: Jiale Zhang Title: Manager Company: Shenzhen Yuejiang Technology Co., Ltd

Shenzhen Yuejiang Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021/11/17 Subject; Request for Confidentiality FCC ID: 2AHI4-BTP-BD2A To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market.

><|Schematic Diagram XxIBlock Diagram

[_]Parts List

>Operational Description

| |Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

[_]External Photos

<|Test Setup Photos X]Internal Photos x]User Manual

[_|For 45 days, pursuant to Public Notice DA 04-1705. OR

[x|For 180 days pursuantto KDB 726920 DO1. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Jicke Dhewy Name: Jiale Zhang Title: Manager Email: zhangjiale@dobot.cc