TURNTABLE PARTS
FUNCTION DESCRIPTION
FUNCTION DESCRIPTION
FUNCTION DESCRIPTION
FUNCTION DESCRIPTION
EN
(cid:31)(cid:30)(cid:29)(cid:28)(cid:27)(cid:26)(cid:25)(cid:24)(cid:23)(cid:25)(cid:22)
A vinyl record player
A6
8
1
2
3
4
5
6
7
GETTING STARTED
Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the unit.
Insert the adaptor’s AC plugs into a power outlet.
necessary.
3. Turn the VOLUME CONTROL KNOB to adjust the volume. The iPod, MP3 player, mobile
phones’ volume control also impact the overall volume level. Please adjust that as well if
BLUETOOTH MODE
1.Turn on the power switch knob. The device enters into Bluetooth mode automatically
AMPLIFIER CONNECTION (IF REQUIRED)
Whilst you can listen to your new turntable using the built in speakers you may
(USB,AUX-IN ports is not occupied)The status indicator will become blue with flashing.
wish to connect it to your existing Hi-Fi system. Connect the audio plugs to the
2.Turn on the Bluetooth function on your mobile phone or tablet PC and search device
Line input on your mixer or amplifier using an RCA cable (not supplied)
name ANESOK-A6. After pairing and connection, the indicator will become blue without
flashing, then you can play your music from your mobile phone or tablet PC through this
turntable player. Turn the VOLUME CONTROL KNOB to adjust the volume. The mobile phone
or tablet PC’s volume control also impacts the overall volume level. Please adjust that as
● Red plug into R/H channel input.
● White plug into L/H channel input.
well if necessary.
PHONO MODE
1. Turn on the power switch knob.
HOW TO REPLACE THE NEEDLE
To replace the needle, please refer to the instructions below.
Removing the needle from the cartridge:
1.Place a screwdriver at the tip of the stylus and push downward as shown in direction “A”.
2. Remove the stylus by pulling the stylus forward and pushing downward.
1.Hold the tip of the stylus and insert the stylus by pressing as shown in direction “B”.
2. Push the stylus upward as in direction "C" until the stylus locks into the tip
NOTES
1. We recommend that you clean your turntable with an anti-static cloth for maximum
protection.
2. We would also point out that for the same reason your stylus should be replaced
periodically (approximately every 250 playback hours)
TIPS FOR BETTER TURNTABLE PERFORMANCE
1. When opening or closing the turntable cover, handle it gently, gripping it either at the
centre or at each side.
turntable platter or record edge.
2. Do not touch the needle tip with your fingers; avoid bumping the needle against the
3. Frequently clean the needle tip-use a soft brush in a “back-to-front’ motion only.
4. If you must use a needle cleaning fluid, use it very sparingly..
5. Gently wipe the turntable player housing with a soft cloth. Use only a small amount of
mild detergent to clean the turntable player.
6. Never apply harsh chemicals or solvents to any part of the turntable system.
1. Choose a safe location and avoid placing the unit in direct sunlight or near any
BEFORE USE
heat source.
2. Avoid locations subject to vibrations, excessive dust, cold, or moisture.
3. Do not open the cabinet as this may result in an electrical shock. If a foreign object is
inserted accidentally contact your dealer.
4. Do not attempt to clean the unit with chemical solvents as this might damage the
finishing. A clean, dry cloth is recommended for cleaning.
5. Keep this manual for future reference.
3. AUTO-STOP ON/OFF switch
11. Power ON/OFF and volume control knob
adapter located in the holder near the tonearm.
12
13
14
9. Status indicator
10. 3.5mm headphone jack
2. Place a record on the turntable platter and select the desired speed (33/45/78)
according to the record. NOTE: when playing a 45RPM record, use the included 45RPM
Installing the Stylus:
12. RCA out port---to connect external
speaker system with built-in amplifier
13. Line in(AUX-IN) port
3. Remove the white needle protector and open the tonearm clip to release the tonearm.
Push the lift lever backward to raise the tonearm and gently move the tonearm towards
position.
the desired position over the record. Push the lift lever forward to lower the tonearm slowly
onto the desired position on the record, Device enters into PHONO mode automatically to
1. 45RPM adaptor
2. Lift lever
4. Speed switch
5. Tonearm
6. Tonearm lock
7. Cartridge with needle
14. DC IN jack—to connect the power
begin playing the record.
8. Platter
adaptor
PARAMETER SPECIFICATION
4.If the AUTO STOP ON/OFF Switch is turned ON, the record will stop playing automatically
when finished (For a few vinyl records, it will stop when it does not come to the end OR it
will not stop when it comes to the end.). If Auto Stop Control is turned OFF, the record will
Model
A6
Bluetooth
V 5.1
NOT stop playing automatically when finished.
Notice: PHONO mode is the highest precedence, must stop PHONO mode to switch into
Input voltage
AC100V~240V
50/60HZ
Play mode
LP/Bluetooth/AUX
BT, AUX, USB mode.
9
10
11
Power Adapter
DC12V/1.0A
Rotational speed
33/45/78 RPM
Product Dimensions
36.8*33*13.6 cm
Record size
7/10/12
AUX IN MODE
1. AUX-IN mode is precedence after plugin, plug 3.5mm Audio cable, Device
enter into AUX-IN mode automatically.
Item Weight
2.35 kg
Power cord length
1 m
2. You can enjoy the music from iPod, MP3 player, mobile phones, etc. through the record
player.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance between 20cm the radiator your body: Use
only the supplied antenna.