91805G-VT transmitter INSTRUCTIONS MANUAL Please read this manual carefully prior to using.We are not responsible for any intentional damage or improper use.lf you require any additional information or have any quesions adout he product or its use,please contact us via www.blqhobby.com This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years old. Contains small parts, keep out of reach of children 3 years of age and younger. MADE IN CHINA Congratulations on your purchase of Turbo Racing 91805G-VT transmitter. Designed using advanced wireless technology, Turbo Racing 91805G-VT will advance and simplify control of your suface model and minimize interference while providing many years of enjoyment. 91805G-VT 73CH AA x4 155.10 193.70 81.30 A U X 3 2 1 Turbo Racing 91805G-VT transmitter is warranted to the original purchaser for 30 days from the date of purchase, verified by the sales receipt, againsr defects in material and workmanship. Product that has been mishandled, abused, used incorrectly, used for an application other than intended or damaged by the user is not covered under warranty. Turbo Racing. is not liable for any loss or damage, whether direct or indirect, incidental or consequential, or from any special situatuon, arising from the use, misuse, or abuse of this product. www.blqhobby.com INSTRUCTIONS MANUAL 7. CH3-EPA+/-
Please put CH4 in the middle of before you press the CH3 EPA+/-,then press EPA+/-, you can adjust the angle of ST 8. CH4-EPA+/-
Please put the CH4 switch on left or right, then press the EPA+/- and adjust the angle Battery compartment: Houses [4] AA batteries 9. 10. Channel 3 key. 11. Multifunction Red Indicator LED:
12. REV:
15 14 13 1. Steering Wheel: Controls left / right motion (note that left-hand use (see full online manual for details). 2. Throttle Trigger: Controls forward / reverse / brake 3. Hand Grip: For holding the transmitter. 4. Antenna: Transmits signal to the receiver located in the vehicle. 5. Power switch: Turns the transmitter ON / OFF. 6. Disassemble keyHandle is removable.
(1). Please turn the wheel to left or right with Max angle , and press REV for 2 seconds,you can hear DI DI, then ST will be reverse
(2). Please pull the throttle or push the throttle to Max position , and press REC for 2 seconds, you can hear DI DI,then REV will be reverse
(3). Please press CH3 and REV together for 2 seconds, you can hear DI DI, then REV will be reverse 14. 13. ST DR/ST TRIM: Please turn the wheel to left or right with Max angle, and press ST-TRIM+ or ST-TRIM-, then adjust the angle of ST TH DR/TH TRIM: Please pull the throttle or push the throttle to Max position, and press TH-TRIM+ or TH-TRIM-, then adjust the angle of TH When you adjust TRIM +/-, you can sound Di, when the trim is on centre, you can sound Di-Di; when the sound is stopped , then means TRIM is Max/Min When you adjust DR +/-, you can sound Di, when the sound is stopped, then means DR is Max/Min 15. Channel 4 key. Disassemble Handle & Install 1.Press the button 2.take away the handle 3.press the button, install the handle www.blqhobby.com INSTRUCTIONS MANUAL Battery Installation Using the AA batteries or NIMH batteries, when the voltage is lower than 4.5V 0.2, the buzzer sounds continuously, and the LED should start flashing. 1. Remove the battery cover from the transmitter. 2. Insert four new AA batteries according to the polarity markings on the battery holder. 3. Reinstall the battery cover. WARNING: DO NOT ATTEMPT TO CHARGE NON-RECHARGEABLE BATTERIES, YOU MAY CAUSE AN EXPLOSION. WARNING: PLEASE DON'T RESERVE THE BATTERY,OR IT WILL BURN OUT THE PCB Connection
(cid:135) Channel 1: Controlled by the wheel, connect to a servo for steering.
(cid:135) Channel 2: Controlled by the trigger, connect to the ESC or a servo for throttle/brake.
(cid:135) Channel 3: Controlled by the adjustment knob
(0-100%) for optional use. This port can also be used to connect a transponder device used in racing.
(cid:135) AUX (Channel 4): Controlled by button (ON/OFF) for optional use. This port is most commonly used for LED light kits. Use this port to connect an external battery for use with gas powered vehicles. CAUTION: NEVER CONNECT A BATTERY WITH VOLTAGE HIGHER THAN 8.0V TO THE RECEIVER, DOING SO COULD DAMAGE THE ELECTRONICS. Receiver Installation & Connection Installation To achieve full operating range with your radio system it is critical that the receiver antenna be undamaged and installed properly. It should be installed with as much of the antenna as possible in a vertical position. The end of the antenna should be contained inside an antenna tube. When installing:
(cid:135) Ensure there are no kinks in the antenna or antenna tube.
(cid:135) Never fold the end of the antenna over the tube, this will reduce the operating range of the system and damage the antenna.
(cid:135) Ensure the receiver is mounted securely or padded against hard impacts. Y-line CH4 CH3 CH2 Channel 4 Servo Channel 3 Servo Throttle Servo connect to receiver battery A U X 3 2 1 Receiver CH1 Pairing The Transmitter & Receiver 1. Turn on the receiver power. Press the SW switch.The receivers LED should start flashing. A U X 3 2 1 2. Turn on the transmitter. 3. When the LED on the receiver becomes solid,the binding process is completed. LED A U X 3 2 1 Note: Radio systems installer in RTRs have already been bound. Only when installing a new transmitter or receiver is the above process necessary www.blqhobby.com INSTRUCTIONS MANUAL Operation A. THROTTLE TRIGGER B. STEERING WHEEL 1. Push the trigger forward to slow down or brake. 2. Pull the trigger backward to accelerate. Fail safe function setting Please turn on the TX, then pull the TH trigger anywhere you want to and hold it, press the SW button of the receiver about 2sec,the LED should start flashing for 5sec,then release SW button and TH trigger, turn off the TX. Using Caution While Operating Safety Precautions Fault Handing When there is no backward function and cant find centre bit, please check the TRIM on centre or not. General Care 1. Always use clean, dry cloth or soft bristle brush to clean your equipment. 2. Never use chemical cleansers, as these could damage the sensitive electronics and plastics. www.blqhobby.com newstone technology co., ltd This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(cid:1068) Reorient or relocate the receiving antenna.
(cid:1068) Increase the separation between the equipment and receiver.
(cid:1068) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(cid:1068) Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.