Insert sixAA" batteries into the Siren Base Unit and one Sv battery into the Motion Sensor Unit. Press the OFF button of the Key Chain Remote. The. . Siren Base Unit should beep once, indicating itis set up and ready to use. ge ns ewer es ene ster rela ta ere ry Place the Siren Base Unit anywhere convenient. It should be out of sight but not muffin the siren (under a seat, etc.) Ifyou prefer, you can install it on a fixed surface with screws or double-sided tape (provided). Confirm the Siren Base Unit is within transmission range of the Motion Sensor Unit by testing the alarm.
(see Using Your Alarm below). Range depends on obstructions and surrounding conditions. (Have alarm professionally installed ifyou are not sure the surface 1s appropriate for installation.) Using Your Alarm TURNING IT ON: Press the ON button of the Key Chain Remote to activate your alarm. The range of your Key Chain Remote depends on obstructions and surrounding conditions. The Siren Base Unit should beep ONCE when armed. When ON, any motion detected by the Motion Sensor Unit activates the Screamer ofthe Siren Base Unit. The alarm stops automatically after 20 seconds, but will start again ifthe Motion Sensor Unit continues to detect motion TURNING IT OFF: Press the OFF button of the Key Chain Remote to disable your alarm, Range of your Key Chain Remote depends on obstructions and surrounding conditions. The Siren Base Unit should beep TWICE, indicating the alarm is deactivated. The Motion Sensor Unit has 3 LEDs on top.
+ The LEDs light red when motion is detected. The LEDs flash green for approximately 15 seconds when vibration is detected, The LEDs can be tumed off without disabling the alarm by setting the adjacent switch to the OFF position. Safoty Note: Always tum off the LEDs when operating a vehicle. Important NOTES:
The Siren Base Unit senses one signal ata time. The Motion Sensor Unit always receives priority. Because of this, you may need to press your Key Chain Remote more than once to turn your alarm on or of. You can continue to use your alarm with the LED switch turned off Setting the LED switch to OFF only deactivates the LEDs. It does ot disable the motion detecting feature ofthe Motion Sensor Unit CAUTION. When the Motion Sensor Unit is installed inside @ car, the LEDs should be set to OFF during the vehicle's operation. Each set uses one of 256 security codes. To change your code:
+ Open the battery doors for both the Key Chain Remote and the Motion Sensor Unit, omoving all batteries. Slide switches up and down to sot code. Codes must be the same on bath Key Chain RRemato and the Motion Sensor Un.
+ Change the DIP switches to any new code, Be sure both the Key Chain Remote and the Motion Sensor Unit are set to the same code.
+ Open the battery door on the Siren Base Unit and remove all, batteries. Wait atleast 15 seconds.
+ Replace the batteries in all 3 units, and press any button on the Key Chain Remote, The Siren Base Unit should beep once, showing itis set up and ready to use. You can reduce the Scream Mode"
sound level by opening the battery door and removing the batteries on the Siren Base Unit. Flip the "H/LO switch to LO to reduce the alarm volume. Replace the batteries and the door. Press the OFF button of the Key Chain Remote. The Siren Base Unit should beep once, showing itis sot up and ready to use. So Activate the False Alarmvlntil Warning mode by opening the battery door and removing the batteries on the Siren Main Unit. Flip the Delay switch into the
(ON position and replace the batteries and the door. Press the OFF button of the Key Chain Remote. The Siren Base Unit should beep once, showing itis set up and ready to use.
+ The first motion detected will tigger the alarm for a short burst.
+ After a 6-second delay if the Motion Sensor Unit continues to detect movement anytime for the next 10 seconds, the alarm goes into full Scream Mode for 20 seconds, and will continue to repeat Lunt no further motion is sensed. Caution:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries accordingly tothe instructions. Components:
+ Motion Sensor Unit w/ vibration & PIR motion sensor (tea) Sion Base Unit (rocelver!speaker) (tea)
+ Key Chain Remote (tea)
+ Accessories:
Mounting holder for sun shadaMisor (tea) Mounting holder for air-conditioning vent (tea) Specifications/Eunctions:
rt UT (VIBRAT
+ Power Source:
= One SV Battery (not included)
+ Battery Life:
~ Approx. 5,000 hours (standbyirest mode)
+ Low Battery Indicator (when motion is sensed):
+3 Red LEDS light up = full bat 2 Red LEDS light up = 15% remaining battery capacity (replace batter)
= Red LED lights up = 10% remaining battery capacity (replace battery)
+ Dotection Range:
Up to 25 Feet / 110
+ Dual LED (Red & Green) indicator:
Red: Lights up when detecting motion.
* Green: Flashes when detecting vibration,
(Flashing stops after 18 seconds)
+ Secret Code Pattoms:
+256 diferent codes (set by 8 dip switches)
+ Operating Temperature:
14 F* (10 C") to 158 F* (470.6%) SIREN BASE UNIT (RECEIVER/SPEAKER)
+ Power Source:
= Six"AA" 1.5V Alkaline Batteries (not included)
+ Battery Life:
~ Approx. 5,000 hours (standbyirest mode)
+ Low Battery Indicator:
= S.extra beeps afler normal onoff signal = 15% remaining capacity
(Replace batteries)
* Speaker:
~Alarm upon detection (Auto stop ater 20 seconds)
+ Alarm Level
= 70d8: Low
=1108: High
+ Audible On/OFF Indicator:
On: 1 beep OF 2 beeps
+ HI/LO Switch:
~ Switches between HI / LO sien levels
(located under battery compartment)
= Delay Switch:
= Switches between Immediate Siren and False Alamvinital Waring mades (located under battery compartment)
+ Code Positions:
+ 256 different codes (Set automatically when batteries are inserted and ther Key Chain Remote button is pressed)
+ Operating Temperature:
14 F* (10 C")10 158 F*(+70.C") Housing:
Waterproof (P44) KEY CHAIN REMOTE
+ Power Source: ro |
= Two GR2025 Lithium button col (Included) oO Bate ie: O!
=foton 3 5yeun uted Bus dy
+ Operation:
= On button: Activates alarm
+ Of button: Deactivates alarm LED:
+ Red LED lights up when transmiting code
(Intensity of LED indicates battery level)
+ Secret Code Patterns:
+ 256 different codes (set by 8 cip switches) Waning:
{Changes or modifications to this unt not expressly approved by the party responsibie for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wll not occur in a particular installation. If this equipment does cause harmful interference to radio or
{elevision reception, which can be determined by turning the equipment off and on, the user is encouraged tory to correct the Interference by one or more ofthe folowing measures:
+ Reorient or relocate the receiving antenna,
+ Increase the separation between the equipment and rocelver.
* Connect the equipment into an outlet ona circuit ifferent from that to which the receiver is connected.
* Consult the dealer or an experienced radlo!TV technician for help. USERS MANUAL for
$SGH1080-AUTO-Blue SGH1080-AUTO-Black
+ Mutple Modon Sensor Unts and Siren Base Units maybe combined protec mute zones, Zneslsctrs are defined by sting 6p suchas 0 he uns. The manufactutng fall 1S08002 Certied Made in China Mantocrd by:
ShieldGuard Led.
{GF Bupa Contre 141 Connaught Road West Hong Kong Pho: +852-2620.0520 Fax: +852-2620.0511 mall nfo@shiotduard cm URL: wot helquard.com Pradut ten hs document are poeta by US nde neatonal Patent oF a8 Patent Pong. ny tingomants il be prosecute oe al axa oe a.