User Manual Hub Mini Contents Getting started Power Internet connection Pairing the Flic/Twist Audio Apple HomeKit requirements Apple HomeKit setup Factory reset Problems Compliance Safety usage guidelines Warranty Notice 1 2 3 4 7 8 9 10 11 11 12 13 14 Getting started To get started make sure that you have:
1. An active Internet connection (WiFi 2.4 Ghz) 2. A phone with the Flic App installed 3. A Flic input device, Flic or Twist, within Bluetooth range of the Flic Hub Mini (Hub Mini) The phone is only necessary during the setup process. Once the setup is complete you no longer need the phone to enjoy Flic!
1 Power Connect the USB-C cable and an external power adapter to the Hub Mini. The Hub Mini will turn on, indicated by a bright red LED. After approximately 15 seconds the LED will dim and become discoverable. Please follow the instructions in the app to complete the initial setup. We recommend that you use an adapter with at least 1A output. An adapter with less than the recommended current rating may result in unstable behavior. 2 Internet Connection To connect the Hub Mini to your WiFi network, open the Flic App and follow the setup steps to get the Hub Mini connected to the internet. If the Hub Mini doesnt have an active internet connection you will not be able to make use of all the available features. To check if the internet connection for the Hub Mini is active, connect to the Hub Mini with the Flic app and go into Settings and look for the Network section and press Test Internet Access. 3 Pairing your Flic Buttons & Twist To pair a brand new Flic or Flic Twist to the Hub Mini, connect to the Hub Mini with the Flic app and simply tap the + button in the bottom right corner. Press and Hold the Flic or Flic Twist until it is recognized by the app.. If you are pairing a Flic that was previously paired then you will need to remove it from that device first. You can do this by navigating to the app page of the Flic you want to remove, tapping the gear icon, and selecting the Remove option. Now you are able to pair this button as described above. 4 Factory reset If, for any reason, you must perform a factory reset, you need to press and hold the pinhole button for between 10-15 seconds. Note that all your account settings will be lost and the Hub Mini will return to factory default. If during the initial setup you assign your own password and forget this then you must perform a factory reset to gain access again. 5 Problems If you have any issues setting up or using the Flic products that are not answered here, please read FAQs at https://start.flic.io/faq Alternatively, you can contact us via https://flic.io/support Compliance Shortcut Labs declaration of conformity is available at https://flic.io/doc For full compliance, list visit https://flic.io/compliance Flic 2 and the Twist are certified as FCC, IC, CE, AUS, R-NZ and WEEE, RoHS, REACH compliant. The Hub Mini is certified as FCC, IC, CE, AUS, R-NZ and WEEE, RoHS, REACH compliant. 6 Safety usage guidelines The Hub Mini is not a toy. It contains small parts and accessories that present a choking hazard. As such it is not suitable for children or pets. General
- Do not attempt to service the product.
- Do not use the product in temperatures below -20C or above +54 C.
- Clean with a damp cloth only. Do not submerge and do not use chemical or abrasive cleaning products. Flic specific
- Battery life will be shortened with heavy usage and/or use in extreme conditions.
- Flic is not waterproof. Do not submerge or attempt to use underwater as this will result in irreversible damage that is outside the scope of the Shortcut Labs AB warranty. 7 Warranty Shortcut Labs AB warrants that your Flic hardware product (the product) will be free from defects in materials and workmanship for a period of 24 months from the date of delivery to the original retail purchaser (the warranty period). If a defect in the product arises within the warranty period, Shortcut Labs will, at its sole option and subject to applicable laws:
(1) repair or replace it with a new or refurbished product or component; or
(2) refund the original purchase price upon return of the defective product. This warranty does not apply to products you purchase from unauthorized resellers, or where the instructions for use and activation of the product are not complied with or where the product is damaged as a result of abuse, accident, modification, moisture or other causes beyond our reasonable control. Note: Battery usage is regarded as normal wear and tear and is therefore not covered by the 24 month warranty. For detailed warranty information visit:
https://flic.io/documents/warranty-police 8 Notice Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help. Caution Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)
(2) this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency (RF) Exposure Warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Canada, Industry Canada (IC) Notices This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:
(1)
(2) this device may not cause interference; and this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1)
(2) susceptible d'en compromettre le fonctionnement. l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions (antennas are greater than 20 cm from a person's body). Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industrie Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mobiles (antennes suprieures 20 cm partir du corps d'une personne) 9 Join us! https://community.flic.io/
Share your ideas with other Flic users and keep up to date with the latest news and happenings from the Flic team. Shortcut Labs AB, Drottning Kristinas Vg 41, 11428, Stockholm, Sweden 10