FCC ID: DD4MXWAPT8 Access Point Transceiver

MXW Wireless Conference System 2012 Shure Incorporated 27WG20831 (Rev. 1) 10/02/12 10/02/12 IMPORTANT SAFETY INSTRUCTIONS 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-

8. DO NOT install near any heat sources such as open flames, radiators, heat registers, tion and install in accordance with the manufacturers instructions. stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-

ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-

nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-

facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. periods of time. 13. UNPLUG this apparatus during lightning storms or when unused for long 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-

paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or 20. Do not attempt to modify this product. Doing so could result in personal injury and/or 21. Operate this product within its specified operating temperature range. protective earthing connection. moisture. product failure. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte-

nance instructions in the literature accompanying this unit. WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. INSTRUCCIONES IMPORTANTES DE SEGURIDAD 1. LEA estas instrucciones. 2. CONSERVE estas instrucciones. 3. PRESTE ATENCION a todas las advertencias. 4. SIGA todas las instrucciones. 5. NO utilice este aparato cerca del agua. 6. LIMPIE UNICAMENTE con un trapo seco. 7. NO obstruya ninguna de las aberturas de ventilacin. Deje espacio suficiente para proporcionar ventilacin adecuada e instale los equipos segn las instrucciones del fabricante. 8. NO instale el aparato cerca de fuentes de calor tales como llamas descubiertas, radiad-

ores, registros de calefaccin, estufas u otros aparatos (incluyendo amplificadores) que produzcan calor. No coloque artculos con llamas descubiertas en el producto. 9. NO anule la funcin de seguridad del enchufe polarizado o con clavija de puesta a tierra. Un enchufe polarizado tiene dos patas, una ms ancha que la otra. Un enchufe con pu-

esta a tierra tiene dos patas y una tercera clavija con puesta a tierra. La pata ms ancha o la tercera clavija se proporciona para su seguridad. Si el tomacorriente no es del tipo apropiado para el enchufe, consulte a un electricista para que sustituya el tomacorriente de estilo anticuado. 10. PROTEJA el cable elctrico para evitar que personas lo pisen o estrujen, particularmente en sus enchufes, en los tomacorrientes y en el punto en el cual sale del aparato. 11. UTILICE nicamente los accesorios especificados por el fabricante. 12. UTILICE nicamente con un carro, pedestal, trpode, escuadra o mesa del tipo especificado por el fabricante o vendido con el aparato. Si se usa un carro, el mismo debe moverse con sumo cuidado para evitar que se vuelque con el aparato. ISTRUZIONI IMPORTANTI PER LA SICUREZZA 1. LEGGETE queste istruzioni. 2. CONSERVATELE. 3. OSSERVATE tutte le avvertenze. 4. SEGUITE tutte le istruzioni. 5. NON usate questo apparecchio vicino all'acqua. 6. PULITE l'apparecchio SOLO con un panno asciutto. 7. NON ostruite alcuna apertura per l'aria di raffreddamento. Consentite distanze sufficienti per un'adeguata ventilazione e installate l'apparecchio seguendo le istruzioni del costrut-

tore. 8. NON installate l'apparecchio accanto a fonti di calore, quali fiamme libere, radiatori, aper-

ture per l'efflusso di aria calda, forni o altri apparecchi (amplificatori inclusi) che generano calore. Non esponete il prodotto a fonti di calore non controllate. 9. NON modificate la spina polarizzata o con spinotto di protezione per non alterarne la funzione di sicurezza. Una spina polarizzata dotata di due lame, una pi ampia dell'altra. Una spina con spinotto dotata di due lame e di un terzo polo di messa a terra. La lama pi ampia ed il terzo polo hanno lo scopo di tutelare la vostra incolumit. Se la spina in dotazione non si adatta alla presa di corrente, rivolgetevi ad un elettricista per far eseguire le modifiche necessarie. denza di spine, prese di corrente e punto di uscita dall'apparecchio. specificati dal costruttore. specificati dal produttore o venduti unitamente all'apparecchio stesso. Se us-

ate un carrello, fate attenzione quando lo spostate con l'apparecchio collocato su di esso, per evitare infortuni causati da un eventuale ribaltamento del carrello stesso. 10. EVITATE di calpestare il cavo di alimentazione o di comprimerlo, specie in corrispon-

11. USATE ESCLUSIVAMENTE i dispositivi di collegamento e gli accessori 12. USATE l'apparecchio solo con carrelli, sostegni, treppiedi, staffe o tavoli 13. DESENCHUFE el aparato durante las tormentas elctricas, o si no va a ser utilizado por 14. TODA reparacin debe ser llevada a cabo por tcnicos calificados. El aparato requiere un lapso prolongado. reparacin si ha sufrido cualquier tipo de dao, incluyendo los daos al cordn o enchufe elctrico, si se derrama lquido sobre el aparato o si caen objetos en su interior, si ha sido expuesto a la lluvia o la humedad, si no funciona de modo normal, o si se ha cado. 15. NO exponga este aparato a chorros o salpicaduras de lquidos. NO coloque objetos llenos con lquido, tales como floreros, sobre el aparato. 16. El enchufe de alimentacin o un acoplador para otros aparatos deber permanecer en buenas condiciones de funcionamiento. 17. El nivel de ruido transmitido por el aire del aparato no excede de 70 dB(A). 18. Los aparatos de fabricacin CLASE I debern conectarse a un tomacorriente de ALI-

19. Para reducir el riesgo de causar un incendio o sacudidas elctricas, no exponga este 20. No intente modificar este producto. Hacerlo podra causar lesiones personales y/o la falla 21. Utilice este producto nicamente dentro de la gama de temperaturas de funcionamiento MENTACION con clavija de puesta a tierra protectora. aparato a la lluvia ni a humedad. del producto. especificadas. Este smbolo indica que la unidad contiene niveles de voltaje peligrosos que representan un riesgo de choques elctricos. Este smbolo indica que la literatura que acompaa a esta unidad con-

tiene instrucciones importantes de funcionamiento y mantenimiento. 13. Durante i temporali o in caso di inutilizzo prolungato dell'apparecchio, SCOLLEGATELO dalla presa di corrente. 14. Per qualsiasi intervento, RIVOLGETEVI a personale di assistenza qualificato. neces-

sario intervenire sull'apparecchio ogniqualvolta stato danneggiato, in qualsiasi modo;

ad esempio la spina o il cavo di alimentazione sono danneggiati, si versato liquido sull'apparecchio o sono caduti oggetti su di esso, l'apparecchio stato esposto alla piog-

gia o all'umidit, non funziona normalmente o caduto. sull'apparecchio oggetti pieni di liquidi, ad esempio vasi da fiori. utilizzabile. 15. NON esponete l'apparecchio a sgocciolamenti o spruzzi. NON appoggiate 16. La spina ELETTRICA o l'accoppiatore per elettrodomestici deve restare prontamente 17. Il rumore aereo dell'apparecchio non supera i 70 dB (A). 18. L'apparecchio appartenente alla CLASSE I deve essere collegato ad una presa elettrica 19. Per ridurre il rischio di incendio o folgorazione, non esponete questo apparecchio alla 20. Non tentate di modificare il prodotto. Tale operazione pu causare infortuni e/o il guasto 21. Utilizzate questo prodotto entro la gamma di temperatura operativa specificata. dotata di messa a terra di protezione. pioggia o all'umidit. del prodotto stesso. Questo simbolo indica la presenza di alta tensione all'interno dell'apparecchio, che comporta il rischio di folgorazione. Questo simbolo indica la presenza di istruzioni importanti per l'uso e la manutenzione nella documentazione in dotazione all'apparecchio. 10/02/12 1. . 2. . 3. . 4. . 5. . 6. . 7. . ,

. 8.

. . 9. .

. 10. , ,

, . 11. ,

. 12. , , ,

. 13. 14. .

, , . 15. . 16. . 17. 70 (A). 18. I 19. , 20. . () 21. .

. IMPORTANTES INSTRUES DE SEGURANA 1. LEIA estas instrues. 2. GUARDE estas instrues. 3. PRESTE ATENO a todas as instrues. 4. SIGA todas as instrues. 5. NO use este aparelho perto de gua. 6. LIMPE SOMENTE com um pano seco. 7. NO bloqueie nenhuma das aberturas de ventilao. Deixe distncias suficientes para 8. NO instale prximo de nenhuma fonte de calor, tais como fogo aceso, radiadores, ventilao adequada e instale de acordo com as instrues do fabricante. bocais de aquecimento, fornos ou outros aparelhos que produzam calor (inclusive ampli-

ficadores). No coloque fontes de chamas sobre o produto. aterramento. Um conector polarizado possui duas lminas com uma mais larga do que a outra. Um conector com pino de aterramento possui duas lminas e um terceiro pino de aterramento. fornecida uma lmina mais larga ou o terceiro pino para a sua segurana. Se por acaso o conector no se encaixar na tomada, chame um eletricista para substituir a tomada obsoleta. 10. PROTEJA o cabo de alimentao, evitando que seja pisado ou que enrosque, especial-

mente nos conectores, nas tomadas eltricas de emprego geral e no ponto onde elas saem do aparelho. 9. NO inutilize as caractersticas de segurana do conector polarizado ou com pino de 11. USE SOMENTE acessrios/apetrechos especificados pelo fabricante. 12. USE somente com um carrinho, pedestal, trip, suporte ou mesa espe-

cificados pelo fabricante ou vendidos com o aparelho. Quando utilizar um carrinho, tenha cuidado ao movimentar o conjunto aparelho/carrinho para evitar danos com a queda do mesmo. 13. DESLIGUE este aparelho da tomada eltrica durante tempestades com relmpagos ou 14. DEIXE toda a manuteno sob a responsabilidade de uma equipe de manuteno quando no seja utilizado por longo perodo. qualificada. necessrio realizar a manuteno quando por algum motivo o aparelho tiver sido danificado de alguma forma, como por exemplo por dano do cabo de alimen-

tao eltrica ou do seu conector, por derramamento de lquido ou queda de objetos no aparelho, se o aparelho tiver sido exposto chuva ou umidade, no esteja operando normalmente ou tenha sofrido queda. lquidos, tais como vasos, sobre o aparelho. para operao. 15. NO exponha o aparelho a respingos ou goteiras. NO coloque objetos cheios de 16. O plugue MAINS (rede eltrica) ou um acoplador de aparelho deve estar sempre pronto 17. O rudo areo do Aparelho no ultrapassa 70 dB (A). 18. O aparelho com construo CLASSE I deve estar conectado tomada da rede eltrica 19. Para reduzir o risco de incndio ou choque eltrico, no exponha este aparelho chuva 20. No tente alterar este produto. Isso poder resultar em leso pessoal e/ou falha do 21. Opere este produto dentro da faixa de temperatura de operao especificada. com ligao terra. ou umidade. produto. Este smbolo indica que existe nesta unidade tenso perigosa que apresenta risco de choque eltrico. Este smbolo indica que existem instrues operao e manuteno importantes na literatura que acompanha esta unidade. 10/02/12 CONSIGNES DE SCURIT IMPORTANTES 1. LIRE ces consignes. 2. CONSERVER ces consignes. 3. OBSERVER tous les avertissements. 4. SUIVRE toutes les consignes. 5. NE PAS utiliser cet appareil proximit de l'eau. 6. NETTOYER UNIQUEMENT avec un chiffon sec. 7. NE PAS obstruer les ouvertures de ventilation. Laisser des distances suffisantes pour 8. NE PAS installer proximit d'une source de chaleur telle qu'une flamme nue, un 9. NE PAS dtriorer la scurit de la fiche polarise ou de la fiche de terre. Une fiche permettre une ventilation adquate et effectuer l'installation en respectant les instructions du fabricant. radiateur, une bouche de chaleur, un pole ou d'autres appareils (dont les amplificateurs) produisant de la chaleur. Ne placer aucune source flamme nue sur le produit. polarise comporte deux lames dont l'une est plus large que l'autre. Une fiche de terre comporte deux lames et une troisime broche de mise la terre. La lame la plus large ou la troisime broche assure la scurit de l'utilisateur. Si la fiche fournie ne s'adapte pas la prise lectrique, demander un lectricien de remplacer la prise hors normes. 10. PROTGER le cordon d'alimentation afin que personne ne marche dessus et que rien ne le pince, en particulier au niveau des fiches, des prises de courant et du point de sortie de l'appareil. 11. UTILISER UNIQUEMENT les accessoires spcifis par le fabricant. 12. UTILISER uniquement avec un chariot, un pied, un trpied, un support ou une table spcifi par le fabricant ou vendu avec l'appareil. Si un chariot est utilis, dplacer l'ensemble chariot-appareil avec prcaution afin de ne pas le renverser, ce qui pourrait entraner des blessures. 13. DBRANCHER l'appareil pendant les orages ou quand il ne sera pas utilis pendant longtemps. 14. CONFIER toute rparation du personnel qualifi. Des rparations sont ncessaires si l'appareil est endommag d'une faon quelconque, par exemple : cordon ou prise d'alimentation endommag, liquide renvers ou objet tomb l'intrieur de l'appareil, exposition de l'appareil la pluie ou l'humidit, appareil qui ne marche pas normale-

ment ou que l'on a fait tomber. 15. NE PAS exposer cet appareil aux gouttures et aux claboussements. NE PAS poser des objets contenant de l'eau, comme des vases, sur l'appareil. 16. La prise SECTEUR ou un coupleur dappareil lectrique doit rester facilement utilisable. 17. Le bruit arien de l'appareil ne dpasse pas 70 dB (A). 18. L'appareil de construction de CLASSE I doit tre raccord une prise SECTEUR dote 19. Pour rduire les risques d'incendie ou de choc lectrique, ne pas exposer cet appareil 20. Ne pas essayer de modifier ce produit. Cela risque de causer des blessures et/ou la 21. Utiliser ce produit dans sa plage de tempratures de fonctionnement spcifie. d'une protection par mise la terre. la pluie ou l'humidit. dfaillance du produit. Ce symbole indique la prsence d'une tension dangereuse dans l'appareil constituant un risque de choc lectrique. Ce symbole indique que la documentation fournie avec l'appareil con-

tient des instructions d'utilisation et d'entretien importantes. WICHTIGE SICHERHEITSHINWEISE 1. Diese Hinweise LESEN. 2. Diese Hinweise AUFBEWAHREN. 3. Alle Warnungen BEACHTEN. 4. Alle Hinweise BEFOLGEN. 5. Dieses Gert NICHT in Wassernhe VERWENDEN. 6. NUR mit einem sauberen Tuch REINIGEN. 7. KEINE Lftungsffnungen verdecken. Hinreichende Abstnde fr ausreichende Belftung vorsehen und gem den Anweisungen des Herstellers installieren. 8. NICHT in der Nhe von Wrmequellen wie zum Beispiel offenen Flammen, Heizkrpern, Wrmespeichern, fen oder anderen Hitze erzeugenden Gerten (einschlielich Verstrkern) installieren. Keine Quellen von offenen Flammen auf dem Produkt platzieren. 9. Die Schutzfunktion des Schukosteckers NICHT umgehen. Ein Schukostecker verfgt ber zwei Steckerzinken sowie Schutzleiter. Bei dieser Steckerausfhrung dienen die Schutzleiter Ihrer Sicherheit. Wenn der mitgelieferte Stecker nicht in die Steckdose passt, einen Elektriker mit dem Austauschen der veralteten Steckdose beauftragen. 10. VERHINDERN, dass das Netzkabel gequetscht oder darauf getreten wird, insbesondere im Bereich der Stecker, Netzsteckdosen und an der Austrittsstelle vom Gert. 11. NUR das vom Hersteller angegebene Zubehr und entsprechende Zusatzgerte verwenden. 12. NUR in Verbindung mit einem vom Hersteller angegebenen oder mit dem Gert verkauften Transportwagen, Stand, Stativ, Trger oder Tisch verwenden. Wenn ein Transportwagen verwendet wird, beim Verschieben der Transportwagen/Gerte-Einheit vorsichtig vorgehen, um Verletzungen durch Umkippen zu verhten. HERAUSZIEHEN. 13. Bei Gewitter oder wenn das Gert lange Zeit nicht benutzt wird, das Netzkabel 14. ALLE Reparatur- und Wartungsarbeiten von qualifiziertem Kundendienstpersonal durchfhren lassen. Kundendienst ist erforderlich, wenn das Gert auf irgendwelche Weise beschdigt wurde, z. B. wenn das Netzkabel oder der Netzstecker beschdigt wurden, wenn Flssigkeiten in das Gert verschttet wurden oder Fremdkrper hineinfielen, wenn das Gert Regen oder Feuchtigkeit ausgesetzt war, nicht normal funktioniert oder fallen gelassen wurde. 15. Dieses Gert vor Tropf- und Spritzwasser SCHTZEN. KEINE mit Wasser gefllten Gegenstnde wie zum Beispiel Vasen auf das Gert STELLEN. 16. Der Netzstecker oder eine Gertesteckverbindung muss leicht zu bettigen sein. 17. Der Luftschall des Gerts berschreitet 70 dB (A) nicht. 18. Das Gert mit Bauweise der KLASSE I muss mit einem Schukostecker mit Schutzleiter in eine Netzsteckdose mit Schutzleiter eingesteckt werden. 19. Dieses Gert darf nicht Regen oder Feuchtigkeit ausgesetzt werden, um das Risiko von Brnden oder Stromschlgen zu verringern. 20. Nicht versuchen, dieses Produkt zu modifizieren. Ansonsten knnte es zu Verletzungen und/oder zum Produktausfall kommen. 21. Dieses Produkt muss innerhalb des vorgeschriebenen Temperaturbereichs betrieben werden. Dieses Symbol zeigt an, dass gefhrliche Spannungswerte, die ein Stromschlagrisiko darstellen, innerhalb dieses Gerts auftreten. Dieses Symbol zeigt an, dass das diesem Gert beiliegende Handbuch wichtige Betriebs- und Wartungsanweisungen enthlt. 10/02/12 Table of Contents Systems Networking Networking Best Practices Network Topologies Multiple Ethernet Switch Setup #1 Multiple Ethernet Switch Setup #2 Multiple Ethernet Switch (Wi-Fi) Setup #3 24 25 25 25 26 26 Configuring Firewalls for Mac or Windows Operating 27 27 27 27 27 28 28 28 28 Configuring Wi-Fi for Wireless Networking Troubleshooting Factory Reset Set Appropriate Latency Settings Dedicate a Device for Master Clock Mac OS Native Firewall Windows XP or Vista Firewall Windows 7 Firewall Opening the MXW GUI Software Introduction Shure Device Discovery Application MXW System Graphical User Interface (GUI) Control Bar GUI Description Inputs/Outputs Tab Preferences Tab Dante Software by Audinate Dante Controller Dante Virtual Soundcard Optimizing the System Site Survey: RF Spectrum Scan Setting RF Gain for Installation Performing a Scan Dynamic RF Power Control Manually Setting RF Power Adjacent Room Freq. Coordination Average Battery Runtime per Power Level Removing/Exchanging a Component from the Group Firmware Updates Troubleshooting Audio Networking Control Software Control Command Strings Safety Information Certifications Specifications 29 30 30 31 31 33 33 33 34 34 34 35 36 36 37 37 37 37 37 38 39 40 40 40 40 40 41 41 42 User Manual IMPORTANT SAFETY INSTRUCTIONS SAFETY PRECAUTIONS CAUTION WARNING WARNING WARNING System Overview General Description and Features Theory of Operation Groups and Audio Channels Network Wireless Audio System Setup Install and Power the Hardware Additional Equipment Requirements Rackmount the ANI Mount the APT Power the Hardware Connect the Components to Form a Network Single Group System (Automatic Configuration) Multiple Group System Access the MXW System Interface Assign Components to a Group Set Up Microphones Microphone Placement Hardware Interface Description Access Point Transceiver (APT) Audio Network Interface (ANI) Front Panel Back Panel 4-Port Network Interface Networked Charger (NCS) Microphones Description Microphone Types and Applications Microphone States Rechargeable Microphone Batteries Recharging the Battery Monitoring the Battery Information Replacing the Battery 3 3 3 3 3 3 3 4 5 6 6 6 6 8 9 9 9 9 9 10 10 10 11 12 13 15 16 17 18 18 19 19 20 21 21 22 22 23 23 23 23 1 10/02/12 2 10/02/12 IMPORTANT SAFETY INSTRUCTIONS 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturers instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that pro-

duce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particu-

larly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use cau-

tion when moving the cart/apparatus combination to avoid injury from tip-over. 13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is re-

quired when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS 19. To reduce the risk of fire or electric shock, do not expose this appara-

20. Do not attempt to modify this product. Doing so could result in personal 21. Operate this product within its specified operating temperature range. socket outlet with a protective earthing connection. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-

14. REFER all servicing to qualified service personnel. Servicing is required when the ap-

tus to rain or moisture. paratus has been damaged in any way, such as power supply cord or plug is damaged, paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. injury and/or product failure. exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or 20. Do not attempt to modify this product. Doing so could result in personal injury and/or 20. Do not attempt to modify this product. Doing so could result in personal injury and/or 21. Operate this product within its specified operating temperature range. 21. Operate this product within its specified operating temperature range. SAFETY PRECAUTIONS The possible results of incorrect use are marked by one of the two sym-

bols"WARNING" and "CAUTION"depending on the imminence of the danger and the severity of the damage. protective earthing connection. protective earthing connection. moisture. moisture. product failure. product failure. WARNING: Ignoring these warnings may cause se-

This symbol indicates that dangerous voltage constituting a risk of This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. vere injury or death as a result of incorrect operation. electric shock is present within this unit. CAUTION: Ignoring these cautions may cause moder-

This symbol indicates that there are important operating and mainte-

This symbol indicates that there are important operating and mainte-

ate injury or property damage as a result of incorrect nance instructions in the literature accompanying this unit. nance instructions in the literature accompanying this unit. operation. WARNING: This product contains a chemical known to the State of California to cause cancer and birth WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. defects or other reproductive harm. 3 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-

7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-

8. DO NOT install near any heat sources such as open flames, radiators, heat registers, 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-

safety. If the provided plug does not fit into your outlet, consult an electrician for replace-

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-

CAUTION Never disassemble or modify the device, as failures may result. Do not subject to extreme force and do not pull on the cable or failures Keep the product dry and avoid exposure to extreme temperatures and may result. humidity. WARNING If water or other foreign objects enter the inside of the device, fire or electric shock may result. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure. This device is able to produce sound volume higher than 85 dB SPL. Please check your maximum allowed continuous noise exposure level based on your national employment protection requirements. WARNING LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE. Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure lev-

els before hearing damage occurs. 90 dB SPL at 8 hours 110 dB SPL at hour 95 dB SPL at 4 hours 115 dB SPL at 15 minutes 105 dB SPL at 1 hour 100 dB SPL at 2 hours 120 dB SPL Avoid or dam-

age may occur WARNING Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140F

(60C), or incinerate Follow instructions from manufacturer Never put batteries in mouth. If swallowed, contact your physician or local poison control center Do not short circuit; may cause burns or catch fire Do not charge or use battery packs with other than specified Shure products Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like WARNING: Danger of explosion if battery incorrectly replaced. Operate only with Shure compatible batteries. Note: Use only with the included power supply or a Shure-approved equivalent. 10/02/12 System Overview System Overview 4 10/02/12 System Overview General Description and Features The Microflex Wireless Series (MXW) is a complete solution for meeting room and presentation applications. Developed with Audinate's Dante technology, the system routes digital audio over standard IP equipment across a network of access points, digital-to-analog converters and computers. Access points mount to a ceiling or wall to communicate wirelessly with the microphones, distributing audio to the Dante network. RF coordination is automatic and continuous, offering worry-free wireless audio transmission for up to 32 channels. Dante Digital Audio Networking Digital audio is carried over standard Ethernet using shielded Cat5e (or higher) cables. Dante provides low latency, tight clock synchronization, and high Quality-of-Service (QoS) to provide reliable audio transport to a variety of Dante devices. Dante audio can coexist safely on the same network as IT and control data, or can be configured to use a dedicated network. Encryption The MXW transmits secure, encrypted audio using Advanced Encryption Standard (AES-256), which conforms to the US Government National Institute of Standards and Technology (NIST) publication FIPS-197. Automatic Frequency Coordination The MXW Series uses automatic frequency coordination to achieve worry-free, solid wireless communication. Frequencies are shared and time-divided between multiple transmitters. A highly accurate time-sync allows multiple APTs to work together for up to 32 channels of wireless transmitters. Microphones are assigned to channels by arranging them in the charger and pressing the link button. The APT assigns the microphones to a channel according to the charger slot number. Remote Control and Monitoring The system can connect to a computer or 3rd party control system (AMX, Crestron, Extron, etc) for remote control and monitoring. The web browser-based graphical user interface (GUI) enables RF spectrum management, audio routing, and microphone behavior. Rechargeable Microphones The MXW series microphones feature an internal rechargeable battery. Microphones charge directly in the charger without the battery removal. During a charging cycle, the GUI displays battery information (battery runtime, charge cycle count and battery capacity). Up to xx hours of continuous use. Built-In RF Spectrum Scanner The MXW APT has the ability to scan the entire RF spectrum for a duration of time. The scan provides an accurate xx insight xx to a location's spectrum availability during typical event hours. Shure Legendary Audio Quality 5 10/02/12 System Overview Theory of Operation Groups and Audio Channels The MXW system uses Groups to organize the audio and control data transport between components. Each Group is comprised of a single access point, charger(s) and audio output device(s). Groups have four or eight channels, depending on the access point model. Once the group is formed, microphones can be linked to the channels from the charging station. Each slot on the charging station corresponds to channels in the group. Automatic Group Dante's self-discovery feature enables a Group to automatically form when the network is comprised of a single APT, ANI and charger. These components must be the same channel count for the automatic association to occur (forming a group of 4 or 8 channels). Setup through the GUI is not necessary for this configuration Network The network is core communication pathway of the MXW system. It transports Dante digital audio with Shure control data over standard IP/Ethernet equipment. When an MXW device joins the network, it automatically configures to compatible IP settings. Gigabit Switch with DHCP For systems with more than eight channels, a gigabit switch is required to create a network of additional access points, chargers and audio output devices. Connecting all components on the same network will ensure the most reliable RF management and digital clock synchronization. In some cases, computer settings or programs may interfere with the network. The majority of these connection issues can be solved by using a DHCP-enabled router. Most routers include a DHCP server, while switches do not. Wireless Audio MXW microphones transmit digital audio in the DECT In the US, wirelesss audio transmits in the unlicensed 1920-1930 MHz frequency band 6 10/02/12 System Overview The following is an overview of each component and its function in the MXW system:

INPUT: SPL OUTPUT: Headphone Network APT INPUT A B line aux sig/clip mute 1 5 2 6 line aux mic 0

-6

-12

-18

-24 adjust 0

-9

-18

-24

-30

-36

-48

-60 Audio Network Interface power ethernet network audio lockout HEADPHONE 1 2 3 4 5 6 7 8 OUTPUT sig/clip mute push to solo | hold to mute ANI 3 7 4 8 NCS GUI Graphical User Interface (GUI) is managed from the The MXW System graphical user interface (GUI). The computer must be networked to the APT to access the GUI from a web browser. Use the software interface for the following system functions:

Assign components to groups to determine the routing of digital audio and control data. Perform an RF spectrum scan to accurately survey a site's spectrum activity over a duration of time. Monitor microphone battery statistics during the charge. Control microphone activity state, gain setting and EQ filters. Customize the function of LED and mute/

active button of the microphone. Configure IP settings. the networking hub of an eight-channel MXW system. Network Port 4 (Uplink) can be configured to restrict audio and provide protected data uplink to a corporate network. Input channels add audio to the network for monitoring at the microphone headphone output. Note: The ANI can be substituted with the Shure SCM820 Digital IntelliMix Mixer. Networked Charging Station (NCS) batteries Recharges microphone by connecting to the USB port of the microphone. Links up to eight microphones at a time to channels in a group. Transmits detailed battery information to the network. LEDs display microphone battery charge status. MXW Microphones Convert audio into a digital RF signal that transmits wirelessly to the APT. Available in a variety of form factors to accommodate any event. Boundary and gooseneck models feature a headphone jack for monitoring audio from the network. Access Point Transceiver (APT) interference Transports encrypted, wireless audio between the microphones and the Dante network. Maintains stable audio transmission through advanced and detection automatic frequency coordination. Requires only a single Cat5e cable for power

(via PoE), system time-sync management, and the communication of networked audio and control data. Hosts the web browser-based GUI for remote system management. Audio Network Interface (ANI) Converts 24-bit/48k digital audio from the network into analog direct outputs. Four-port gigabit switch enables the ANI to be 7 10/02/12 System Setup System Setup 8 10/02/12 System Setup Install and Power the Hardware Additional Equipment Requirements Network Cables Ensure all network cables are shielded Cat5e or higher and do not exceed 100 m between network devices. Audio Cables Reference the guide supplied with the MXWANI Hardware Kit to assemble the output cables to the connectors and strain relief tabs. Gigabit DHCP Router DHCP routers provide the most reliable networking hub for the system. Rackmount the ANI Use the screws and washers supplied in the Hardware Kit to mount the ANI. Mount the APT Position the Access Point The access point contains multiple directional antennas to provide steady, reliable wireless communication. The cardioid radiation pattern is strongest from the top of the face plate. Use the following guidelines when mounting the access point:

Direct the antenna toward the intended coverage area. Position access point so there is nothing obstructing a line of sight to the microphones. Keep antennas away from large metal objects. Mount access points at least four feet apart. Important: Always perform a "walk around" test to verify coverage before using a wireless system during a speech or performance. Experiment with antenna placement to find the optimum location. If necessary, mark

"trouble spots" and ask presenters or performers to avoid those areas. Mount the Unit Secure the unit to a ceiling or wall using the supplied mounting screws. Power the Hardware ANI Connect the IEC power cable from the back panel to an AC power source. Turn on the power switch. APT The APT requires PoE to operate. Use a Cat5e cable to connect the APT to the ANI port 1 or to a gigabit switch with PoE. There is no power switch. Charger Connect the PS45 external power supply from the charger to an AC power source. Turn on the power switch. Gigabit Ethernet Router or Switch Connect the router or switch to an AC power source. Turn on the power switch. 1 2 3 4 5 6 7 8 gain low cut hi shelf meter push to solo | hold to mute AUX IN L+R SUM MASTER A B gain limiter A B LIM 0

-9

-18

-24

-36

-48

-60 power ethernet network audio automix link dual mixer lockout HEADPHONE 1 Power Link 4 3 2 1 uplin k Class 0 Po E 2 1 5 2 6 3 7 4 8 1 Class 0 Po E 15V 0.6A power 1 5 2 6 3 7 4 8 9

++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE1++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE110/02/12 System Setup The following are two setup examples for the MXW system. See Networking section for more details on Dante digital audio and networking best practices. Connect the Components to Form a Network Single Group System (Automatic Configuration) Use a Cat5e cable to connect the charger and APT to one of four ports of the ANI network interface. Reference the table for connecting to the ports:

Port Port 1 (PoE) Port 2 Port 4 (Uplink) To Component APT Charger Computer (optional) Requirements:

Cat 5e (or higher) Shielded Ethernet Cables (100 m) cables Multiple Group System Follow these steps for connecting a multiple-group system:

1. Connect a DHCP enabled router to a computer. 2. Connect each charger and audio output device to the router with network 3. Connect each access point to the network via a PoE source. Requirements:

Cat 5e (or higher) Shielded Ethernet Cables (100 m) Gigabit Ethernet switch (DHCP-enabled router recommended) Computer 4 3 2 1 uplin k Class 0 Po E 1 5 2 6 3 7 4 8 Single-Group System Power Link ON OFF DHCP 1 5 2 6 3 7 4 8 15V 0.6A power ON DHCP OFF 1 Class 0 Po E ON OFF DHCP PoE www.shure.com MXWANI8 M XW AN I8

www.shure.com MXWANI8 M XW AN I8

www.shure.com MXWANI8 M XW AN I8

www.shure.com MXWANI8 M XW AN I8

Input: 100-240V ~ 1A max. 50/60 Hz Input: 100-240V ~ 1A max. 50/60 Hz Input: 100-240V ~ 1A max. 50/60 Hz Input: 100-240V ~ 1A max. 50/60 Hz

1 5 1 5 1 5 1 5 4 3 2 1 uplin k Class 0 Po E 4 3 2 1 uplin k Class 0 Po E 4 3 2 1 uplin k Class 0 Po E 4 3 2 1 uplin k Class 0 Po E 2 6 2 6 2 6 2 6 3 7 3 7 3 7 3 7 4 4 4 4 8 8 8 8 Four-Group System 10

++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE1++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE110/02/12 System Setup The MXW System is controlled and monitored on a graphical user interface (GUI) that opens in a web browser. The computer must be networked to the APT to access the GUI. Access the MXW System Interface 1. Load and install the Discovery Application. This automatically installs the required Bonjour device discovery tool to the computer. 2. Launch the application. The app displays all Shure devices on the network. Model MXWANI8 MXWAPT8 Name ANI1 Conference1 DNS name mxwani-aa1.local mxwapt8-ffe761.local Dante IP Address 192-168-200-22 yes 192-168-200-23 yes 3. Select and open the APT. The MXW System Interface opens in a web browser. 4. Bookmark the device's DNS name. The DNS name is used to access the interface without the Discovery App. Name ANI 1 APT 1 DNS name mxwani-aa1.local mxwapt8-ffe761.local IP Address 192-168-200-22 192-168-200-23 11 10/02/12 System Setup Components must be assigned to a group to form the communication link of audio and control data. On the Configuration tab, select the following components to form a group of up to 8 channels:

Assign Components to a Group 1. Select an APT for Group 1 The pop-up menu will display all APTs on the network. This determines if the group has four or eight channels (APT4 or APT8). 2. Select the charger(s). When using gooseneck microphones, it is necessary to use two chargers for 8 microphones. (Gooseneck microphones take up front and back slots.) 3. Select the Audio Output Device(s). This can be an ANI4, ANI8 or SCM820 IntelliMix Mixer. id? Button flashes the LEDs of the selected device for easy identification during setup. 12 10/02/12 System Setup 1. Arrange microphones in the charger. Microphones are linked to channels according to the arrangement in the charger. Set Up Microphones 8-Channel Charger

(NCS8) 4-Channel Charger

(NCS4) 1 1 5 5 Power Link 2 2 6 6 3 3 7 7 4 4 8 8 1 3 Power Link 2 4 Charger Slots Correspond to Channels 1 Power Link 5 2 6 For gooseneck mics For bodypacks, handhelds and boundary mics. 3 4 7 8 Connecting the Microphone to the Charger Slot 2. Link the microphones to channels. The Link procedure can be done from two places:

Charger: Press and hold the Link button for 6 seconds. The LEDs flash during the process and turn solid green once the link is successful. GUI: From the Configuration page, press the Link button in the group row. 1 link 5 2 6 3 7 4 8 13 7865123410/02/12 System Setup 15V 0.6A power 3. Remove mics from the charger. The microphone status LEDs will flash, and will remain steady once the audio is ready. 4. Set mic gain Mic gain is adjusted on the Monitor tab of the GUI. Signal indicator Gain adjustment 14 Monitor Tab

++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE1++++++++++www.shure.comMXWANI8MXWANI8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 PoE110/02/12 System Setup For best low-frequency response and rejection of background noise, place the microphone on a large, flat surface, such as a floor, table, or lectern. To reduce reverberance, avoid reflective surfaces above or to the side of the microphone, such as beveled sides of pulpits or overhanging shelves. Microphone Placement 15 10/02/12 Hardware Interface Description Hardware Interface Description 16 10/02/12 Hardware Interface Description Access Point Transceiver (APT) Power LED Illuminates green when Power over Ethernet (PoE) is provided. Network Audio LED Solid Green: Sending or receiving a digital audio signal. Flashing Green: Cannot establish a connection. RF Link LED Color Green Solid Yellow Flashing Yellow Solid Red Flashing Red Status 1 linked microphone is powered on in the Active or Mute state. 1 linked microphone is in the Standby or Off state. The ID button in the GUI has been pressed. Problem with RF connection ???

No microphones are linked to the unit. Reset Button Press and hold the reset button for 10 seconds to hard reset the MXW system to factory default settings. Note: Performing a reset will delete system configurations made in the GUI, including device association and microphone link. Ethernet Jack Connects a Cat5e (or higher) cable to a PoE source and the network. Network Status LED (Green) Off = no network link On = network link established Flashing = network link active Network Speed LED (Amber) Off = 10/100 Mbps On = 1 Gbps Cable Routing Path Routes the Ethernet cable to enable a flush-mount to the surface. 17 10/02/12 Hardware Interface Description Audio Network Interface (ANI) B line aux OUTPUT sig/clip mute 3 4 1 2 5 6 7 8 A INPUT sig/clip mute Audio Network Interface power ethernet network audio lockout HEADPHONE 0

-9

-18

-24

-30

-36

-48

-60 line aux mic 0

-6

-12

-18

-24 adjust push to solo | hold to mute Front Panel Input Channels Adds analog line- or aux-level signals to the digital network. When associated to the APT, inputs are automatically routed to linked microphone channels (Input A to channels 1-4; Input B to 5-8). Typical applications include sending translated audio or a mix for personal monitoring at the microphone headphone jack. Output Channels Sends analog audio out from the digital audio network. When connected to the MXW system, the outputs are automatically routed from the associated MXWAPT. Channel Select Button Selects a channel and performs the following functions:

Action Function Listen to the channel at the headphone jack Display and adjust channel gain Monitor output signal level on the Level Meter Mute/unmute a channel. Mute is indicated by the Mute LED. Single Press Press and Hold (3 seconds) Selected Channel LED Illuminates when a channel is selected. Signal Strength LED (sig/clip) Indicates audio signal strength for each channel:

Green = Normal Amber = Strong Red = Clipping (to eliminate clipping, attenuate the signal level at the audio source) Mute LED Illuminates red when the Channel Select button is held for 3 seconds, muting the channel. A muted channel is still routed to the HEADPHONE jack for monitoring or troubleshooting. Input Level Select Buttons Set the selected channel to line- or aux-level to match the input signal. Output Level Select Buttons Set the selected channel to an output level that matches the connecting device:

line: +4 dBU aux: 10 dBV mic: 30 dBV 18 Output Gain Control Use the up/down buttons to adjust the channel gain attenuation from 0 dB (no attenuation) to -24 dB. Output Gain Setting Displays the attenuation made from the Output Gain Control. Level Meter Displays a selected channels audio level in dBFS. It is good practice to use -18 dBFS on the output meter as an approximation of 0 VU on an analog meter. Hardware Status LEDs Illuminate to indicate the status of the hardware:

LED power Ethernet network audio Color Green Green Green Flashing Green lockout Red Status Unit is powered on. Connected to an Ethernet device. Sending or receiving a digital audio signal. Cannot establish a connection. Front panel gain and mute controls are locked. The LED will blink when a button is pressed while the hard-

ware is locked. A channel can still be selected for headphone monitoring. Headphone Volume Knob Adjusts the volume to the headphone output. Headphone Output 1/4 (6.35 mm) output jack for monitoring a selected channel. 10/02/12 Hardware Interface Description Back Panel Input: 100-240V ~ TBD A max. 50/60 Hz MXWANI8 AC Power IEC connector 100 - 240 V AC. Power Switch Powers the unit on or off. Output Block Connectors (1-8) Three-pin, low-voltage connector provides a direct output for each channel. Chassis Ground Use to directly ground the cable shield to the chassis. Input Block Connectors (A,B) Three-pin, low-voltage connector adds line- or aux-level analog signals to the digital network. 4 3 2 1 uplink Class 0 PoE Reset Button Press and hold the button for five seconds to reboot the device with factory default settings. Network Status LED (Green) Off = no network link On = network link established Flashing = network link active Network Speed LED (Amber) Off = 10/100 Mbps On = 1 Gbps Network Interface Digital Audio connection and networking capabilities with shielded Cat-

5e (or higher) cable. 4-Port Network Interface Port Port 1 (PoE) Ports 2 and 3 Port 4 (Uplink) Description Provides Power over Ethernet (PoE) for the Shure MXWAPT Access Point. Connects to an additional ANI for clock syn-

chronization, to an MXW charger, or to a con-

trol system. By default, this port functions the same as ports 2 and 3. However, it can be configured to provide password protected uplink to corporate LAN without network audio traffic. When Port 4 Uplink is enabled from the GUI, it only provides access to the GUI, blocking data to the Shure Discovery Application, Dante Controller and Dante Virtual Soundcard. 4 3 2 1 uplink Class 0 PoE 19 10/02/12 Hardware Interface Description Networked Charger (NCS) Charging Slots (USB 2.0 Type A Plug) Store, recharge and link microphones in the USB slots. Slots are associated to channels in an APT according to the system setup in the GUI. Power LED Illuminates when the unit powered on. Link LED Illuminates after a successful link. Link Button Press and hold for 10 seconds to link all microphones in the charger to channels of the associated APT. Battery Status LEDs Monitor microphone battery status during a charge, in increments of 10, 25, 50, 75, 100%

Locking DC Power Supply Jack Screw the PS45 power supply to the input, illuminating the POWER LED. Power Switch Powers the unit on or off Ethernet Port Connects to the MXW system using a Cat5e (or higher) cable. Network Status LED (Green) Off = no network link. On = sending or receiving digital audio over the network. Flashing = cannot establish a connection. 1 Power Link 5 2 6 3 7 4 8 Network Speed LED (Amber) Off = 10 Mbps On = 100 Mbps Charger Slots Correspond to Audio Channels 1 1 5 5 Power Link 2 2 6 6 3 3 7 7 4 4 8 8 1 3 Power Link 2 4 8-Channel Charger (NCS8) 4-Channel Charger (NCS4) 20 10/02/12 Hardware Interface Description Microphones Description Power Button Press button to turn the microphone on; the microphone LED will flash green and red until turning a solid color (color depends on state specified in GUI). Press and hold for 3 seconds to power off. Note: The bodypack does not have a dedicated power button. Mute/Active Button Changes the microphone state to Active or Mute. Each microphone type can be set to toggle or push-and-

hold from the Preferences tab of the GUI. The following describes the function of each setting:

Toggle:Press and release the button to change the status to Active or Mute. Push-to-talk:Hold button to pass audio. Push-to-mute:Hold button to mute the audio. Microphone State LED Indicates the microphone state. Pulsing Red = Standby mode; Off = microphone is off. Customize the indication of Active and Mute for each transmitter type from the Preferences tab of the GUI. These options are displayed in the following table:

Mute Solid Red Flashing Red Solid Red Off Flashing Green Active Solid Green Solid Red Off Solid Red Solid Green Standby mode is always represented with a pulsing red LED. Low Battery LED (Gooseneck and Boundary only) Gooseneck and boundary microphones only. Color Off Solid Red Flashing Red Status

>10% battery runtime remains 10% battery runtime remains Battery is too low to transmit an RF signal. Recharge the microphone. Earphone Jack 1/8" (3.5 mm) jack for monitoring the return channel signal, such as translated audio. Charge Connector (USB 2.0 Type A Jack) Connects to the NCS charger slot or to the optional (?? model) USB adapter cable. 21 10/02/12 For each event, select microphones that will best serve the arrangement of participants and presenters. The following is a chart of each microphone and its primary use:

Type Gooseneck Placement Notes Hardware Interface Description Microphone Types and Applications Choosing a Microphone Type Boundary Bodypack Use Sits on a desk or podium with an extended neck for close talking Sits flat on a table or desk to provide coverage for one or two people. Connects to a lavelier microphone for placement on a speaker's clothing. When no lavalier is con-

nected, an internal omnidirectional microphone is activated. Microphone States After a microphone has been linked to the network, it is in one of four states (or, levels of activity). The follow-

ing is a summary of each state:

Active Ready to pass audio to network. Mute Audio is muted. Standby Audio is muted and the microphone is in a hibernation state to conserve the battery. Off No connection to the network. The microphone must be turned on using the power button on the mic. Initial States After Removing from Charger Each microphone type can be assigned to a specified state whenever it is removed from the charger. Go to the Preferences tab of the GUI to set the initial state for each microphone type. When the Initial State is set to Standby, pressing the microphone's mute button will return it to one of two states as defined in the Switch behavior:

Push-to-talk Active toggle For example, an installer may prefer to have the handheld microphones exit the charger with a Mute status to avoid transmitting any handling noise to the audience. 22 10/02/12 Hardware Interface Description Rechargeable Microphone Batteries MXW microphones feature the Shure rechargeable Lithium-ion battery. Lithium-Ion chemistry and intelligent Shure battery circuitry results in a rechargeable battery with no memory effect. It can be recharged at any time; a complete discharge is not necessary. 5 6 1 5 7 2 6 3 7 4 8 8 Recharging the Battery There are two ways to recharge the microphone battery:

Using the NCS Charger Use the charger slots to recharge and store the microphones. Handheld, bodypacks, and boundary microphones use the vertical slots; gooseneck mi-

crophones use the back horizontal slots.

?? Model USB Power Adapter The USB adapter allows the microphone to charge during operation. Monitoring the Battery Information Charge to Full Indicators When the microphone is charging in the NCS charging station, the charger LEDs display battery in increments of 10, 25, 50, 75, 100%

For further detail, the Monitor page displays the time to full charge in hours:minutes. Battery Runtime Remaining When the microphone is out of the charger, the Monitor tab will display the runtime remaining in hours:minutes. Battery Life Statistics On the Utility tab of the GUI, two battery life statistics that are displayed:

% Battery Capacity: Percentage of charge capacity compared to a new battery Cycle Count: Number of charge cycles logged by the battery. Replacing the Battery Caution! Danger of exploding if battery is incorrectly replaced. Use only with the same or equivalent type. Use the following guidelines for replacing the battery:

1. Unscrew and open the battery door. 2. Disconnect the battery from the microphone. Properly dispose of the old 3. Plug the new battery to the jack on the microphone. 4. Replace the battery door and screw it shut. battery. 23 10/02/12 Networking Networking Dante technology uses standard IP over Ethernet and safely coexists on the same network as IT and control data. It provides an integrated solution to transport two types of data over the same network cable: Shure Control, and Dante Audio and Controller. Shure Control: GUI and 3rd Party Control The Shure Control carries data for the GUI operation, firmware updates and 3rd party control systems

(AMX, Crestron, Extron). This data is transmitted over all MXW components connected to the network. Dante Audio and Controller This network carries both the Dante digital audio and the control data for Dante Controller. This data is transmitted between the APT and the ANI. 24 10/02/12 Networking Networking Best Practices Use the following best practices when setting up a network to ensure reliable communication:

Always use a "star" network topology Use only 1 DHCP enabled server per network. Disable DHCP addressing on additional servers When using an AXT620 Ethernet Switch, turn on the switch first before turning on additional components connected to the network To expand the network, use multiple Ethernet switches in a star topology Connect each device directly to the port of an Ethernet switch. Avoid "daisy-

chaining" Ethernet port connections between devices for larger networks. Do not loop network connections All networked devices must be set to the same subnet mask All devices must be at the same firmware revision level, with the exception of the AXT620 Ethernet Switch There are several ways to configure a network of devices. In general, you should always use a "star" network topology where each device uses one connection to an Ethernet switch port. If multiple switches are used, each switch is individually connected to one connection to the next level of Ethernet switch. Below are three example configurations of large networks of devices. Network Topologies Multiple Ethernet Switch Setup #1 Any AXT620 switch (but only one) can be set as the DHCP server Each networked device needs an individual connection to the switch Connect them via any port Server Client Client AXT620 with front panel DHCP switch set to OFF AXT620 with front panel DHCP switch set to OFF AXT610 ShowLink Access Point AXT620 with front panel DHCP switch set to ON 25 10/02/12 Networking Multiple Ethernet Switch Setup #2 Each networked device needs an individual connection to the switch. AXT620 with front panel DHCP switch set to ON Ethernet Switch Server Client AXT610 ShowLink Access Point Multiple Ethernet Switch (Wi-Fi) Setup #3 Each networked device needs an individual connection to the switch. Wi-Fi Router (DHCP enabled) AXT620 with front panel DHCP switch set to OFF Server Client Client AXT620 with front panel DHCP switch set to OFF AXT610 ShowLink Access Point 26 10/02/12 Networking Configuring Firewalls for Mac or Windows Operating Systems Windows 7 Firewall 1. From the Start menu, select Control Panel. 2. Select Systems and Security. 3. Select Windows Firewall. 4. Select Allow a program or feature through Windows Firewall. 5. To view the list of applications, select Change Settings. 6. Select the following applications to allow them:

WWB6.exe SLPD.exe SNETDAMEON.exe Mac OS Native Firewall 1. Open System Preferences. 2. Select Security, and then select the Firewall tab. 3. To enable editing, make sure the lock icon at the bottom of the window is 4. If the firewall is on, select Advanced. For each of the following applications, Wireless Workbench 6.app slpd snetDameon acnproxy unlocked before entering your password. select "Allow Incoming Connections":

Windows XP or Vista Firewall 1. From the Start menu, select Control Panel. 2. Select Windows Firewall. 3. In the Windows Firewall window, if the firewall is set to On, select the WWB6.exe SLPD.exe SNETDAMEON.exe Exceptions tab and add the following applications to the exceptions list:

Configuring Wi-Fi for Wireless Networking When using Wireless Workbench over Wi-Fi, its important to set up the wireless router properly for best performance. Wireless Workbench employs multicast data protocols to communicate to the Axient and PSM1000 devices. Wi-Fi treats broadcast and multicast packets differently than general packets for backward compatibility reasons. In some cases, the Wi-Fi router will limit the multicast packet transmission rate to a value that is too slow for Wireless Workbench to properly operate. By default, most Wi-Fi routers are configured to operate in b/g-mode, which tells the router to allow both 802.11g and older 802.11b devices to operate over the network. In this configuration, some routers will automatically limit the multicast data rates (or sometimes referred to as basic rate, or management rate) to 1-2Mbps. For small wireless microphone configurations of less than 20-30 channels, this Wi-Fi setting should not cause any problems with Wireless Workbench. Tip: For larger wireless microphone configurations of greater than 30 channels, its recommended to configure the Wi-Fi router to operate in g-mode only. Most routers will increase the multicast transmission rate to 6Mbps when operating in g-mode thereby providing adequate bandwidth to Wireless Workbench. Important: For best performance, use a Wi-Fi router that does not limit the multicast rate to 1-2 Mbps. Shure recommends the following Wi-Fi router brands:

Cisco Linksys Apple 27 10/02/12 Networking Troubleshooting Factory Reset If a device isn't appearing on the network, perform a hard reset to return the device to default settings. Factory default settings are designed for automatic com-

patibility with other Shure networked devices. Use following instructions to reset each device:

Access Point Transceiver Press and hold the reset button for 10 seconds. The network audio status LED will briefly turn off to indicate the unit is rebooting. Note: Factory resets delete system configurations made in the GUI, including device association and microphone linking. Audio Network Interface Press and hold the reset button for 5 seconds. The front panel LEDS will flash to indicate the unit is rebooting. Networked Charging Station Press and hold the link button while powering up the charger. Continue to hold the link button for 10 seconds. The LEDs will flash to indicate the unit is rebooting. Set Appropriate Latency Settings Latency settings determine the amount of time that a device can spend processing data packets. When a receiver is overloaded with traffic, audible clicks and pops may occur. Increasing the latency setting will improve performance for large networks. Number of Switch Hops*

Recommended Latency Setting

* Each device is represents one switch hop. Dedicate a Device for Master Clock Dante uses the IEEE 1588 Precision Time Protocol (PTP) to automatically determine a single access point to act as the master clock for the network. This is typically the first APT that connects to the network (if several connect simultaneously, the master defaults to the APT with the lowest MAC address). The remain-

ing Dante audio components slave to the master When a master device shuts down or goes offline, the system will automatically begin selecting another master. During this selection time (up to xx seconds), the entire system will NOT pass audio. If the network or building management requires that devices are periodically shut down, you can manually select an access point as the Preferred Master device from Dante Controller software. This allows the installer to set up the system to ensure that the master access point never shuts down during events. 28 10/02/12 Software Introduction Software Introduction MXW hardware networks to a computer to operate with several software programs, augmenting the system with additional features and comprehensive remote management. The following software components are used with the MXW series:

Shure Device Discovery Application: Uses Bonjour networking technology to display all Shure devices on the network that include a graphical user MXW Series GUI: Hosted from the APT webserver and accessed from a typical web browser, this GUI is used to manage the network of MXW components. MXWANI GUI: Hosted from the ANI webserver and accessed from a typical web browser, this GUI is used to monitor the ANI's analog inputs/outputs and interface (GUI). network configuration. Dante Controller: Dante Controller (DC) is a free software by Audinate that is used to configure and manage a network of Dante devices. Dante Virtual Soundcard: An audio driver used to monitor and record digital audio without additional equipment. 29 10/02/12 Software Introduction The Device Discovery application finds all Shure devices on the same network that have an embedded web server. These devices network with a computer to access the The Discovery app is included on the CD-Rom supplied with the APT and can be downloaded from the Shure website. Shure Device Discovery Application Device Discovery with Bonjour: Bonjour software is bundled with the installation of the Shure Device Discovery application. Bonjour technology provides zero configuration networking, allowing devices to automatically discover each other and configure to compatible settings. Opening the MXW GUI To access the MXW system GUI, follow these steps:

1. Load the Shure Device Discovery CD to a computer and install the application. Bonjour will install automatically to the computer. 2. Connect the PC to the same network as the APT. 3. Turn off the PC's WiFi to force the wired network interface. 4. Open the Discover app to view all Shure devices on the network. 5. Double-click on a unit to open its GUI in a browser. Note: When Port 4 Uplink mode is enabled on the ANI, the Discovery app will not find the GUI. However, the GUI can still be opened by the bookmark or manually typing in the DNS name into the browser. Recommended: Bookmark the GUI The Discovery app uses Bonjour technology to open a device's GUI using its DNS name (Domain Name System). The DNS name is unique for each device and will never change (unlike IP addresses). Bookmark the GUI using the DNS name allows reliable access to the GUI without going through the Device Discovery app. 30 10/02/12 Software Introduction A graphical user interface (GUI) is software that allows comprehensive system control and monitoring from a computer. It is hosted from an embedded server built into the APT, and is accessible when properly networked to a computer or 3rd party control device. All hardware functions can be adjusted using the GUI. MXW System Graphical User Interface (GUI) GUI Description The following is a description of each tab of the GUI:

Monitor Tab APT Selection Selects an APT for monitoring channel and RF spectrum information. Spectrum Meter Displays the RF spectrum availability from a scan from the APT. See Spectrum Scan section for more details. Global Mic Control Controls the status of all microphones linked to the APT. Microphone Name Microphone names can be customized with up to 31 any characters in length except '=','.' or '@'. Identify Button When clicked, this commands the microphone to beep and its LED to flash. Microphones must be removed from the charger for this function. Battery Status While charging: Displays the remaining time until the microphone battery is fully charged. Not charging: Displays the remaining battery runtime of the microphone. RF Signal Strength Audio Input Meter Indicate the average input signal level. LED Red (6) Yellow (5) Yellow/ Green (4) Green (3) Green (2) Green (1) Audio Signal Level

-0.1 dBFS

-6 dBFS

-12 dBFS

-20 dBFS

-30 dBFS

-40 dBFS Description Overload Normal peaks Signal Present 31 Mic Gain Adjusts microphone gain from -25 dB to +15 dB gain in 1 dB steps. High Pass Filter Engages a 6 dB-per-octave filter below 150 Hz for attenuating undesired low frequencies, sometimes caused by table vibrations or air-conditioning rumble. Low Pass Filter Engages a 6 dB-per-octave filter above 15 kHz for attenuating undesired high frequencies, sometimes caused by sibilant vocals or paper rustling. Microphone State Microphones are in one of four states:

Active: Microphone is on and passing audio to the network. Mute: Microphone is on but the signal is muted. Standby: Conserves battery charge and allows the GUI to change the state to Active or Mute. Off (Inactive): The microphone is powered off. A microphone in this state cannot be controlled by the GUI (it can only be turned on using the power button on the mic). Microphone Type Displays the microphone type:

Gooseneck Bodypack Boundary Handheld Return Channels Monitor the signal level and mute/unmute the audio of the return channel. 10/02/12 Configuration Tab Device List Customize the switch for each microphone type. Device Name Device names can be customized with up to 31 any characters in length except '=','.' or '@'. Network Interface Selection Determines which network interface's IP settings are displayed. Control:

Network Audio:

IP Mode Sets IP mode of the selected network interface:

Auto (DHCP): For automatic DHCP or Link-Local IP addresses. Manual (Static): For Static IP addresses. IP Settings Displays the IP Address, Subnet Mask, and Gateway for each network interface. MAC Address The network interface's unique identification. Group Row Assign APTs, chargers, and audio output devices to form each group. id? Button Commands the selected device's LEDs to flash for easy identification. Links microphones to channels for the selected charger. Link Button Utility Tab Export Exports the data table to a text file that can be saved to a computer. Group Indicates to which group the device is assigned/linked. Device The device type or microphone channel. Type The device model number. Name Displays name as defined in ______??

IP Address Control Displays the IP Address of the control network interface (Shure GUI control). IP Address Network Audio Displays the IP Address of the Network Audio network interface (Dante audio and control). S/N Displays the device's serial number.

% Battery Capacity Percentage of charge capacity compared to a new battery. Cycle Count Number of charge cycles logged by the battery. Current Version Displays the device's firmware version. Software Introduction Preferences Tab Switch Behavior Customize the switch for each microphone type. Toggle: Press and release the button to change the status to Active or Mute. Push-to-talk: Hold button to pass audio. Push-to-mute: Hold button to mute the audio. Disabled: The button does not affect the audio. Initial State from Charger Assigns the initial state for each microphone type after removal from the charger:

Active: Microphone is on and passing audio to the network. Mute: Microphone is on but the signal is muted. Standby: Conserves battery charge and allows the GUI to change the state to Active or Mute. Off (Inactive): The microphone is powered off. A microphone in this state cannot be controlled by the GUI (it can only be turned on using the power button on the mic). LED Behavior Set the behavior of the mute/active LED for each microphone type:

Mute Solid Red Flashing Red Solid Red Off Flashing Green Active Solid Green Solid Red Off Solid Red Solid Green Standby mode is always represented with a pulsing red LED. Mute Preference Local Mute - Individual: Each microphone is muted individually. Local Mute - All: All microphones mute when any microphone is muted. External Mute: Microphones are muted by a 3rd-party control device. RF Power Max Determines the maximum distance that an APT will transmit. Low: ??'

Medium: ??'

Medium High: ??'

High: ??'

Out of Range Alarm Back in Range Action Linking Preference Language Save/Load Preferences Password Setup Register the Product Link 32 10/02/12 Software Introduction Control Bar Identify Button This button sends a command to the hardware to flash front-panel LEDs for easy identification. Log Off Logs the user out of the GUI. This appears only when a password has been set for Admin or Tech level. Language Selection Selects the language for the GUI. This setting will be saved to the computer. Normal: Enables automatic Dante channel routing with an APT. Standalone: Channels must be routed manually with Dante Controller software. Device Name Device name is customizable by clicking in the text box. Names can be up to 12 characters long (alphanumeric and a limited set of special characters are allowed). Addressing Mode Auto: IP settings are Link-Local or automatically accepted from a DHCP server. Manual: IP settings (IP Address, Subnet Mask, and Gateway) are static and are entered manually. MAC Address Port 4 Mode Configures the Port 4 of the network interface:

Switched (default): Full Ethernet support. Uplink: Only control data for the GUI is transported. Multicast traffic for Dante and the Shure Device Discovery is restricted. Front Panel Lockout Disables the front panel controls on the hardware. Channels can still be selected for monitoring at the headphone jack. Password By default, the GUI has no password or security levels. Setting a password for the Admin will automatically generate a Guest-level logon. An additional, Tech-level logon can be created. The following describes the access rights of each logon type:

Admin: Full editing rights. The Admin can enable or disable a Tech-level logon. Tech: Rights are limited to the functions that are also editable from the hardware: gain, mute, solo, and reset. Guest: Monitoring only. Inputs/Outputs Tab Inputs (Return Channels) Channel Name Channel name is customizable by clicking in the text box. Names can be up to 12 characters long. Input Gain Setting (A, B) Sets the analog input gain level. Audio Meter Displays input audio levels prior to the analog-to-digital converter. Mute Button Mutes or unmutes the channel's audio. The button illuminates red when a channel is muted. Outputs (1-8, or 1-4) Channel Name Channel name is customizable by clicking in the text box. Names can be up to 12 characters long. Output Gain Sets the output gain level. Audio Meter Displays output audio levels prior to the digital-to-analog converter. Attenuation Output attenuation is adjustable in 1 dB increments. Mute Button Mutes or unmutes the channel's audio. The button illuminates red when a channel is muted. Various Network Audio Status Green = Sending or receiving a digital audio signal. Flashing green = Cannot establish a connection. Notes Save project notes here, such as installation dates or IP information. Preferences Tab Language Selects the language for the GUI when the ANI is in Standalone Network Mode. In Normal mode, this is defined in the APT GUI. Device Serial Number Displays the devices serial number. Firmware Version Displays the current firmware version of the device. Reset Button Reboots the device with factory default settings. Register This Product Link Click to register the device at shure.com to receive product and software updates. Networking Mode 33 10/02/12 Software Introduction Dante Software by Audinate Audinate software provides additional function and control of the Dante digital audio network. Visit Audinate's website for instructions for download and installation. Dante Controller Dante Controller (DC) is a free software by Audinate that is used to configure and manage a network of Dante devices. Use it to route channels between Dante-enabled devices and to monitor the status of the device, clock, and network. Note: DC software is not required for routing audio within the MXW system. Use caution when us-

ing DC, as changing settings may interfere with MXW system functionality. Dante Virtual Soundcard Dante Virtual Soundcard (DVS) acts as an audio driver used to monitor and record digital audio without additional equipment. DVS uses a computer's standard Ethernet ports to transmit and receive up to 64 channels from any Dante enabled device on the same network. 34 10/02/12 Optimizing the System Optimizing the System 35 10/02/12 Optimizing the System Site Survey: RF Spectrum Scan The APT features a scanning tool to survey the RF spectrum prior to the installation. It should be conducted during typical hours of activity to identify the avail-

ability of the RF spectrum. The channel count limit will be determined by the availability of clear spectrum. During a scan, the APT turns off all associated microphones in order to survey the spectrum of the room for interference from devices such as cordless phones, walkie-talkies, or intercoms. Performing a Scan The following steps are used to perform the RF scan:

1. Connect the APT and computer to the same network. 2. Open the Monitor tab of the GUI and press the Start Scan button. 3. Run the scan for the entire time that an event may take place. 36 10/02/12 Optimizing the System Setting RF Gain for Installation Dynamic RF Power Control By default, the MXW system automatically adjusts the RF power level based on the distance between an APT and the microphones. This prevents signal dropout if a microphone is taken outside of the radius of the coverage of the current RF level. Note: Greater RF coverage uses more battery power and decreases the battery runtime. Additionally it increases the required distance between systems. RF Level and Coverage Area Level 3: 100'

Level 2: 50'

Level 1: 25'

Manually Setting RF Power You can limit the RF gain in order to maximize RF efficiency of a fixed space and save microphone battery life. There are three stages of RF gain in the APT for coverage over a range of installation sizes: Level 3: 100' radius, Level 2: 50' radius, Level 1: 25'

radius. RF setting affects the microphone battery (higher level uses more power, reducing battery runtime) and the system ability to reuse channels in a space. Using a lower gain level decreases space the needed between systems to avoid conflicting DECT frequency allotment. Adjacent Room Freq. Coordination Average Battery Runtime per Power Level The following table displays the average runtime of the transmitter for each RF power level:

RF Power Level Low Medium Medium High High Microphone Runtime

? hours

? hours

? hours

? hours 37 10/02/12 Optimizing the System Removing/Exchanging a Component from the Group To exchange a microphone, place the new microphone in the charger slot that corresponds to the desired channel. Press and hold the link button for 10 seconds to link the microphone to the channel. The old microphone will no longer be a part of the system and no change will occur for the remaining channels. Important: Always note the charger slot and channel when replacing microphones. The link will immediately override the existing microphone's audio and RF connection to the system. 38 10/02/12 Firmware Updates Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional features and enhancements. To take advantage of design improvements, new versions of the firmware can be uploaded and installed using the Firmware Manager tool. Software is available for download from http://www.shure.com. Perform the following steps to update the firmware for the MXWANI:

Firmware Updates CAUTION! Ensure the device has a stable network connection during the update. Do not turn off the device until the update is complete. 1. Download Firmware Update Manager from http://www.shure.com and install the software. 2. Open the software. 3. Click Check Now to view new versions available for download. 4. Select the updates and click download. 5. Connect the device and computer to the same network. If Port 4 is used, ensure Port 4 Mode is set to Switched mode (default) on the Preferences tab. 6. Download the latest firmware to the device. Once the download is complete, the device automatically begins the firmware update, which overwrites the existing firmware. 39 10/02/12 Troubleshooting Firmware Updates Audio Networking Control Software Control Command Strings 40 10/02/12 Firmware Updates Safety Information MXW1 Bodypack Microphone Transmitters:

These transmitters have been tested and found to comply with international radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal oper-

ating conditions. These transmitters must not be co-located or operating in conjunction with any other antenna or transmitter. MXW6, MXW8, MXWAPT4, MXWAPT8 Tabletop Gooseneck Microphone Transmitters, Tabletop Boundary Microphone Transmitters, Wireless Access Point Transmitters:

These mobile transmitters are intended for use at distances greater than 20 centimeters from the human body. These mobile transmitters are exempt from the testing requirements of international radiation exposure standards due to their proximity to the body of the user in their intended use case and their low power output. These mobile transmitters shall be placed or installed at least 20 cm from any person and must not be co-located or op-

erating in conjunction with any other antenna or transmitter. Important Product Information The equipment is intended to be used in professional audio applications. EMC conformance testing is based on the use of supplied and recom-

mended cable types. The use of other cable types may degrade EMC performance. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment. Please follow your regional recycling scheme for batteries, packaging, and electronic waste. Note: This device is not intended to be connected directly to a public internet network. Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Certifications This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est auto-

rise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage ra-

diolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Conforms to electrical safety requirements based on IEC 60065. This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com The CE Declaration of Conformity can be obtained from: www.shure.com/

europe/compliance Authorized European representative:

Shure Europe GmbH Headquarters Europe, Middle East & Africa Department: EMEA Approval Jakob-Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: 49-7262-92 49 0 Fax: 49-7262-92 49 11 4 Email: EMEAsupport@shure.de MXWNCS4, MXWNCS8 Authorized under the FCC verification provision per Part 15b. This Class B digital apparatus complies with Canadian ICES-003. Cet appa-

reil numrique de la classe B est conforme la norme NMB-003 du Canada. Note: See the label located on the bottom side of the charger enclosure for the FCC marking, the CE marking, the C-Tick marking, and the elec-

trical ratings. MXW1, MXW2, MXW6, MXW8, MXWAPT4, MXWAPT8 Certified under FCC Part 15. FCC: DD4MXW1, DD4MXW2, DD4MXW6, DD4MXW8, DD4MXWAPT4, DD4MXWAPT8. Meets applicable requirements of RSS-213. IC:

616A-MXWAPT4, 616A-MXWAPT8. 616A-MXW1, 616A-MXW6, 616A-MXW8, 616A-MXW2, 41 10/02/12 Firmware Updates Specifications 42 10/02/12 United States, Canada, Latin America, Caribbean:

Shure Incorporated 5800 West Touhy Avenue Niles, IL 60714-4608 USA Phone: 847-600-2000 Fax: 847-600-1212 (USA) Fax: 847-600-6446 Email: info@shure.com 2011 Shure Incorporated www.shure.com Europe, Middle East, Africa:

Shure Europe GmbH Jakob-Dieffenbacher-Str. 12, 75031 Eppingen, Germany Phone: 49-7262-92490 Fax: 49-7262-9249114 Email: info@shure.de Asia, Pacific:

Shure Asia Limited 22/F, 625 Kings Road North Point, Island East Hong Kong Phone: 852-2893-4290 Fax: 852-2893-4055 Email: info@shure.com.hk 10/02/12