Specifications:
The following specifications apply to the UR1M micro bodypack only. UR1M Micro Bodypack Transmitter Addendum Features Same audio performance as UR1 Rapid two-way infrared (IR) data transmission User-adjustable RF output level (10 mW or 50 mW) Operates with two type of primary batteries: alkaline or lithium Audio signal is input through a TA4F connector (UR1M) or a LEMO connector (UR1MLEMO3) Selectable battery metering by battery type Audio metering on UR1M transmitter that is the same as UR4 receiver UR1M Band G1 H4, H4E J5 J5E L3E, L3 Q5 Q6 Q9 R9 R16, R18 A24 JBX X1 Frequency Range Range 470-530 MHz 518-578 MHz 578-608, 614-638 MHz 578-638 MHz 638-698 MHz 740-814 MHz 740-752 MHz 740-806 MHz 790-865 MHz 794-806 MHz 779-788, 797-806 MHz 806-810 MHz 944-952 MHz RF Carrier Frequency Range 470-865, 944-952 MHz depending on region Working Range 150 m (500 ft.), under typical conditions 500 m (1600 ft.) line-of-sight, outdoors for a single system NOTE: Actual working range depends on RF signal absorption, reflection and interference RF Power Output 10 mW or 50 mW depending on region Power Requirements:
Two 1.5V AAA alkaline, primary lithium, and NiMH batteries Current Drain:
130 mA max. at 3V (normal RF power setting) 200 mA max. at 3V (high RF power setting) 27A11964 (Rev. 1) 2008 Shure Incorporated Battery Life (Typical):
Alkaline Lithium primary NiMH 5 hours (normal RF power) 3 hours (high RF power) 9 hours, typical 3 hours, typical Select Battery Type:
Set the the micro bodypack transmitter switch to on Press enter key, then scroll using type. Press enter key to confirm. Overall Dimensions button to select battery 49 mm L x 60 mm W x 17 mm D (1.9 x 2.38 x 0.66 in.) Net Weight 62 g (2.2 oz.) without batteries Wiring TA4F Connector Microphone Element TA4F Connector TA4M Connector UR1 MIC JACK BOARD Active Load Audio Ground NOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHERGUITAR CABLE DOES NOT. LEMO Connector Microphone Element UR1 LEMO BOARD FVB.00.303 XRB.00.303 Audio Ground Printed in U.S.A. REPLACEMENT PARTS AND ACCESSORIES Furnished Accessories Antenna, 470-530 MHz........................................................UA701 Antenna, 518-578 MHz........................................................UA711 Antenna, 578-638 MHz .......................................................UA721 Antenna, 638-698 MHz .......................................................UA722 Antenna, 740-865 MHz .......................................................UA731 Antenna, 944-952 MHz .......................................................UA741 Optional Accessories Bodypack Pouch (Black) ..................................................WA581B Bodypack Pouch (White) ................................................ WA581W 3-Pin mini Lemo conversion kit...........................................WA335 3-Pin mini Lemo Jack for Lavalier ......................................WA336 Assembly Tool for WA336...................................................WA337 UR1M Transmitter RF Output Connector:
Actual Impedance:
Pin Assignments:
SMA 50 Shell = Ground Center = Signal UR1M Transmitter Audio Input Connector:
Input Configuration:
Maximum Input Level:(1 kHz, 1% THD) TA4M Connector Pin Assignments:
LEMO Connector Pin Assignments:
4-Pin male mini connector
(TA4M) 3-Pin female mini connector
(LEMO XRB.00.303) Unbalanced, active
+5 dBu (sensitivity 0 dB)
+15 dBu (sensitivity 10 dB) Pin 1: Ground Pin 2: +5 VDC bias Pin 3: Audio Pin 4: Tied through active load
(on main board) to ground.
(On instrument adapter cable, Pin 4 floats) Pin 1: Ground Pin 2: +5 VDC bias Pin 3: Audio
(8.2 k between pin 2 and 3 internal to UR1M) Certification UR1M: Type Accepted under FCC Parts 74 (FCC ID: DD4UR1MA, DD4UR1MB, DD4UR1MC, DD4UR1MF, DD4UR1MG). Certified by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR1MA, 616A-UR1MB, 616A-UR1MC). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking. The EU Declaration of Conformity can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.com LICENSING INFORMATION:
Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the users responsibility, and licensability depends on the users classification and applica-
tion, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.