BLX BLX -- Wireless System Online user guide for Shure BLX wireless system. Version: 2 (2019-D) Shure Incorporated BLX Wireless System IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturers instructions. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. ONLY USE attachments/accessories specified by the manufacturer. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. UNPLUG this apparatus during lightning storms or when unused for long periods of time. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. The MAINS plug or an appliance coupler shall remain readily operable. The airborne noise of the Apparatus does not exceed 70dB (A). Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure. Operate this product within its specified operating temperature range. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. 2/25 Shure Incorporated This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries. System Components Note: Your system comes with a combination of the following components. BLX1 Bodypack Transmitter BLX2 Handheld Transmitter (choice of SM58, BETA58A, or PG58) BLX4 Wireless Receiver BLX88 Dual Wireless Receiver PS24 Power Supply Lavalier microphone (choice of PG185, WL185 or WL93) Headworn microphone (choice of PG30, SM31FH or SM35) MX153 Earset microphone Instrument microphone (BETA98H/C) Guitar cable (WA302) Quick Start Guide 1. 1. Connect receiver to power source. 2. Connect receiver to mixer or amplifier. Hold power button to turn on. 2. Press group button on receiver to perform a group scan. 3. 1. Install batteries and turn on transmitter. 3/25 Shure Incorporated 2. On the transmitter, set the group and channel to match the receiver. The audio LED on the receiver should illuminate. If setting up additional systems, leave the first transmitter and receiver on. For each additional receiver, manually set the group to match the first receiver. Note: The receiver will automatically perform a channel scan to find an available frequency after the group has been selected. Set the transmitter frequency to match the receiver. 4. If sound is too faint or distorted, adjust the gain accordingly. 4/25 Shure Incorporated Features Front Panel BLX4 BLX88 audio LED Indicates strength of incoming audio signal: green for normal and red for overload. ready LED Green light indicates system is ready for use and receiving transmitter signal. LED Display Displays group and channel setting. group and channel Buttons Scan: Push and release group button to scan for an open group and channel. Manual: Push and hold group button to select a group. Push channel button to select a channel in the current group. power Button Push and hold to turn power on or off. Back Panel BLX4 5/25 BLX88 DC Power Jack Adapter Cord Tie-Off XLR microphone output jack (MICout) 6.35 mm (1/4") instrument level output jack (instrumentout) BLX1 LED Indicator Displays power and battery status (see Transmitter LED Indicators). power Switch Toggles power on or off. 4-Pin Microphone Input Jack (TA4 connector) Antenna group Button Changes group setting. LED Display Displays group and channel setting. channel Button Changes channel setting. Battery Compartment Audio Gain Adjustment Rotate to increase or decrease transmitter gain. Shure Incorporated 6/25 Shure Incorporated BLX2 LED Indicator Displays power and battery status (see Transmitter LED Indicators). power Button Push to turn power on or off. group Button Changes group setting. channel Button Changes channel and gain setting. LED Display Displays group and channel setting. Identification Cap Battery Compartment Transmitter LED Indicators LED Indicator Green Status Ready 7/25 Shure Incorporated LED Indicator Status Rapidly Flashing Red Controls locked Solid Red Battery power low (less than 1 hour remaining*) Flashing Red and shuts off Batteries dead (change batteries to power on transmitter)
*For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead. Single System Set Up Before you begin, turn off all transmitters and turn on any equipment (other microphones or personal monitoring systems) that could cause interference during the performance. 1. Press and release the group button on the receiver. The receiver scans for the clearest group and channel. Note: If you want to stop the scan, push the group button again. 2. Turn on transmitter and change the group and channel to match the receiver (See Setting Transmitter Group and Channel). Once the system is set up, perform an audio check and adjust the gain if necessary. Setting Transmitter Group and Channel Transmitter group and channel must be manually set to match the receiver. Group (letter) 1. 2. Press and release the group button on the transmitter to activate the display. Press the group button again and the display flashes. While the display is flashing, press the group button again to advance to the desired group setting. Channel (number) If channel needs to be changed, follow the same procedure using the channel button instead of the group button. Note:
When the group and channel correctly match the receiver, the ready LED on receiver illuminates. After manual setup, the transmitter alternately displays the group and channel setting for about two seconds. 8/25 Shure Incorporated Multiple System Setup Up to 12 systems can operate simultaneously (band and RF environment dependent). Important: Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered on. Otherwise, scans from the other receivers will not detect that channel as occupied. For the BLX88, be sure to setup both transmitters before progressing to the next receiver. Turn on any other equipment that could cause interference during the performance so it will be detected during the group and channel scans in the following steps. Before you begin system set up, turn all receivers ON and all transmitters OFF. For the first receiver:
1. Perform a group scan. This finds the group with the most clear channels. Note: For the BLX88, the group scan sets up both receivers at the same time. 2. 3. Turn on the first transmitter and change the group and channel to match receiver. Leave the transmitter on and continue with the additional systems. Note: If the selected group does not contain enough open channels, manually select group "d" when setting up larger systems. For each additional receiver:
1. 2. 3. 4. Use manual setup to change the receiver to match the group setting of the first receiver. Recall that each time the group setting is changed, a channel scan is automatically done. Turn on the transmitter and change the group and channel to match the receiver. Leave the transmitter on and continue to the next system. Once all receivers are set up, perform an audio check on all microphones. 9/25 Shure Incorporated Manually Setting Receiver Group and Channel The receiver group may need to be changed as part of a multiple system setup. Group (letter) 1. 2. 3. Hold the group button on the receiver until the display begins to flash. While the display is flashing, press the group button again to advance to the next group. Note: Only the group setting will be displayed during the manual setup. Once the desired group is reached, release the group button. The receiver automatically performs a channel scan. Channel (number) Always use a channel selected by the channel scan. However, if necessary, the channel can be set manually. Follow the same steps above using the channel button instead of the group button. Locking and Unlocking Controls Lock system controls to prevent accidental setting changes or power off. Transmitter (lock/unlock) Turn the transmitter on. Hold the group button, then press the channel button for approximately 2 seconds. The LED indicator rapidly flashes red when locked. Receiver (lock/unlock) Turn the receiver on. Simultaneously hold the group and channel button. The display flashes rapidly. When locked, the display flashes rapidly if any key is pressed. The BLX88 locks on both sides when locked from either side. Tips to Improve Wireless System Performance If you encounter interference or dropouts, try the following suggestions:
Choose a different receiver channel Reposition the receiver so there is nothing obstructing a line of sight to the transmitter (including the audience) Avoid placing transmitter and receiver where metal or other dense materials may be present Move the receiver to the top of the equipment rack Remove nearby sources of wireless interference, such as cell phones, two-way radios, computers, media players, Wi-Fi devices, and digital signal processors Charge or replace the transmitter battery Keep transmitters more than two meters (6 feet) apart Keep the transmitter and receiver more than 5 meters (16 feet) apart During sound check, mark trouble spots and ask presenters or performers to avoid those areas 10/25 Getting Good Sound Correct Microphone Placement Shure Incorporated Hold the microphone within 12 inches from the sound source. For a warmer sound with increased bass presence, move the microphone closer. Do not cover grille with hand. Wearing the Headworn Microphone Position the headworn microphone 13 mm (1/2 in.) from the corner of your mouth. Position lavalier and headworn microphones so that clothing, jewelry, or other items do not bump or rub against the microphone. Adjusting Gain Monitor the audio LED indicator on the receiver front panel when setting the transmitter gain. Green: normal levels 11/25 Shure Incorporated Red: excessive sound levels (overload). The red LED should only illuminate infrequently when you speak loudly or play your instrument loudly. BLX1 Rotate the audio gain adjustment to increase (+) or decrease () the gain until desired level is reached. For instruments, turn gain to minimum setting. For lavaliers, increase the gain as desired. BLX2 The BLX2 features two gain level settings, default and attenuated (-10 dB). The default setting is used for most situations. If the receiver audio LED flickers red often, set the microphone to attenuated. Use the channel button to change the gain setting. 1. Hold down the channel button for 5 seconds. A dot appears on the lower right-hand corner of the LED display, which indicates 10 dB gain setting has been activated. 2. To change the gain back to default, hold the channel button again for 5 seconds, or until the dot disappears. Batteries Expected life for AA batteries is up to 14 hours (total battery life varies depending upon battery type and manufacturer). When the LED indicator turns red, it signifies "low battery" with approximately 60 minutes of remaining battery life. 12/25 For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead. To remove batteries from the handheld transmitter, push them out through the opening in the microphone battery compartment. Shure Incorporated WARNING: Battery packs shall not be exposed to excessive heat such as sunshine, fire, or the like. Wearing the Bodypack Transmitter Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown. For best results, the belt should be pressed against the base of the clip. Power Off Hold down the power button to power off the BLX2 or BLX4/88. To power off the BLX1, slide the power toggle switch to OFF. 13/25 Shure Incorporated Removing and Installing Identification Caps The BLX2 is equipped with a black identification cap from the factory (dual vocal systems ship with additional gray cap). To remove: Remove battery cover. Squeeze sides and pull off cap. To install: Align the cap and click into place. Replace battery cover. An Identification Cap Kit containing assorted colored caps is available as an optional accessory. Troubleshooting Issue Indicator Status Solution No sound or faint sound Receiver ready LED on Receiver ready LED off Receiver LED screen off Verify all sound system connections or adjust gain as needed (see Adjusting Gain) Verify that the receiver is connected to mixer/
amplifier Turn on transmitter Make sure the batteries are installed correctly Perform transmitter setup (see Single System Setup) Insert fresh batteries Make sure DC adapter is securely plugged into electrical outlet. Make sure receiver is powered on. 14/25 Issue Indicator Status Solution Transmitter indicator LED flashing red Replace transmitter batteries (see Changing Batteries). Shure Incorporated Audio artifacts or dropouts Ready LED flickering or off Change receiver and transmitter to a different group and/or channel. Identify nearby sources of RF interference, and shutdown or remove source. Replace transmitter batteries. Ensure that receiver and transmitter are positioned within system parameters System must be set up within recommended range and receiver kept away from metallic surfaces. Transmitter must be used in line of sight from receiver for optimal sound Distortion Audio LED on receiver indicates overload (red) Reduce transmitter gain (see Adjusting Gain). Sound level variations when switching to different sources N/A Adjust transmitter gain as necessary (see Adjusting Gain). LED/display flashing rapidly See Locking and Unlocking Controls. Receiver/transmitter won't turn off Specifications System Working Range 91 m (300 ft) Line of Sight Note: Actual range depends on RF signal absorption, reflection and interference. Audio Frequency Response 50 to 15,000 Hz Note: Dependent on microphone type Total Harmonic Distortion Ref. 33 kHz deviation with 1 kHz tone 0.5%, typical 15/25 Shure Incorporated Dynamic Range 100 dB, A-weighted, typical Operating Temperature
-18C (0F) to 57C (135F) Note: Battery characteristics may limit this range. Polarity Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low-impedance output) and the tip of the high impedance 1/4-inch output.
-16 dBV maximum
+10 dBV maximum BLX1 Audio Input Level max min (0 dB) Gain Adjustment Range 26 dB Input Impedance 1 M RF Transmitter Output 10 mW, typical varies by region Dimensions 4.33 in. X 2.52 in. X 0.83 in. (110 mm X 64 mm X 21 mm) H x W x D Weight 2.6 oz. (75 g), without batteries Housing Molded ABS Power Requirements 2 LR6 AA batteries, 1.5 V, alkaline 16/25 Battery Life up to 14 hours (alkaline) Audio Input Level 0dB
-10dB Gain Adjustment Range 10 dB RF Transmitter Output 10 mW, typical varies by region
-20 dBV maximum
-10 dBV maximum Dimensions 8.82 in. X 2.09 in. (224 mm X 53 mm) L x Dia. Weight 7.7 oz. (218 g) without batteries Housing Molded ABS Power Requirements 2 LR6 AA batteries, 1.5 V, alkaline Battery Life up to 14 hours (alkaline) BLX4 & BLX88 Output Impedance XLR connector 6.35 mm (1/4") connector Audio Output Level Ref. 33 kHz deviation with 1 kHz tone XLR connector 27 dBV (into 100 k load) Shure Incorporated 200 50 17/25 6.35 mm (1/4") connector 13 dBV (into 100 k load) Shure Incorporated RF Sensitivity
-105 dBm for 12 dB SINAD, typical Image Rejection
>50 dB, typical Dimensions BLX4 1.57 in. X 7.40 in. X 4.06in. (40 mm X 188 mm X 103 mm) H x W x D BLX88 1.50 in. X 12.13 in. X 3.98in. (38 mm X 308 mm X 101 mm) H x W x D 8.5 oz. (241 g) 15.1 oz. (429 g) Weight BLX4 BLX88 Housing Molded ABS Power Requirements 1215 V DC @ 160 mA (BLX88, 320 mA), supplied by external power supply (tip positive) Certifications Meets essential requirements of the following European Directives:
WEEE Directive 2002/96/EC, as amended by 2008/34/EC RoHS Directive 2011/65/EU Note: Please follow your regional recycling scheme for batteries and electronic waste This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/
compliance (http://www.shure.com/europe/compliance) Authorized European representative:
Shure Europe GmbH Headquarters Europe, Middle East & Africa Department: EMEA Approval 18/25 Shure Incorporated Jakob-Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: +49-7262-92 49 0 Fax: +49-7262-92 49 11 4 Email: EMEAsupport@shure.de Certified under FCC Part 74. Certified by ISED in Canada under RSS-123 and RSS-102. FCC ID: DD4BLX1A, DD4BLX1B, DD4BLX1C, DD4BLX1D; DD4BLX2A, DD4BLX2B, DD4BLX2C, DD4BLX2D, DD4BLX1W, DD4BLX1S, DD4BLX2W, DD4BLX2S, DD4BLX1H11, DD4BLX2H11, DD4BLX1J11, DD4BLX2J11. IC:
616A-BLX1A, 616A-BLX1B, 616A-BLX1C, 616A-BLX1D; 616A-BLX2A, 616A-BLX2B, 616A-BLX2C, 616A-BLX2D, 616A-BLX1H11, 616A-BLX2H11, 616A-BLX1J11, 616A-BLX2J11 Certified by ISED in Canada under RSS-102 and RSS-210. IC: 616A-BLX1W, 616A-BLX1S, 616A-BLX2W, 616A-BLX2S Approved under the Declaration of Conformity (DoC) provision of FCC Part 15. Important Product Information LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the users responsibility, and licensability depends on the users classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to the user This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. 2. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 19/25 Shure Incorporated Canada Warning for Wireless This device operates on a no-protection, no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Economic Development Canadas document Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Low-Power Radio Apparatus in the TV Bands. Ce dispositif fonctionne selon un rgime de nonbrouillage et de nonprotection. Si lutilisateur devait chercher obtenir une certaine protection contre dautres services radio fonctionnant dans les mmes bandes de tlvision, une licence radio serait requise. Pour en savoir plus, veuillez consulter la Circulaire des procdures concernant les clients CPC2128, Dlivrance de licences sur une base volontaire pour les appareils radio de faible puissance exempts de licence et exploits dans les bandes de tlvision dInnovation, Sciences et Dveloppement conomique Canada. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. 2. This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. 2. Lappareil ne doit pas produire de brouillage;
Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B) Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Australia Warning for Wireless This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band. Frequency Range and Transmitter Output Level Band H8 H8E Range 518 to 542 MHz 518 to 542 MHz Output Power 10 mW 10 mW 20/25 Band H9 H10 H10E H11 H62 J10 J11 K3E K12 K14 M15 M17 M18 Q24 Q25 R12 S8 T11
*
Range 512 to 542 MHz 542 to 572 MHz 542 to 572 MHz 572 to 596 MHz 518 to 530 MHz 584 to 608 MHz 596 to 616 MHz 606 to 630 MHz 614 to 638 MHz 614 to 638 MHz 662 to 686 MHz 662 to 686 MHz 694 to 703 MHz 748 to 758 MHz 742 to 766 MHz 794 to 806 MHz 823 to 832 MHz 863 to 865 MHz Shure Incorporated Output Power 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW 10 mW Note: Frequency bands might not be available for sale or authorized for use in all countries or regions. NOTE: This Radio equipment is intended for use in musical professional entertainment and similar applications. This Radio apparatus may be capable of operating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power levels for wireless microphone products. 21/25 Shure Incorporated Frequencies for European Countries H8E 518-542 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, EST F, GB, GR, H, I, IS, L, LT NL, P, PL, S, SK, SLO DK, FIN, M, N HR, E, IRL, LV, RO, TR Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 518 - 542 MHz*
518 - 542 MHz*
518 - 542 MHz*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. K3E 606-630 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, EST F, GB, GR, H, I, IRL, L, LT NL, P, PL, S, SK, SLO DK, FIN, M, N HR, E, IRL, LV, RO, TR Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 606 - 630 MHz*
606 - 630 MHz*
606 - 630 MHz*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. 22/25 Shure Incorporated K14 614-638 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, EST F, GB, GR, H, I, IS, L, LT NL, P, PL, S, SK, SLO DK, FIN, M, N HR, E, IRL, LV, RO, TR Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 614 - 638 MHz*
614 - 638 MHz*
614 - 638 MHz*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. K14 614-638 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, EST F, GB, GR, H, I, IS, L, LT NL, P, PL, S, SK, SLO DK, FIN, M, N HR, E, IRL, LV, RO, TR Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 614 - 638 MHz*
614 - 638 MHz*
614 - 638 MHz*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. 23/25 Q25 614-638 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, EST F, GB, GR, H, I, IS, L, LT NL, P, PL, S, SK, SLO RO Shure Incorporated Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 742 - 766 MHz*
742 - 766 MHz*
742 - 766 MHz*
742 - 743; 750 - 751; 758 - 759 MHz*
HR, E, IRL, LV, TR, DK, RIN, M, N
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. R12 796-806 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel N Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich 796 - 806 MHz*
A, B, BG, CH, CY, CZ, D, DK, E, EST F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT LV, M, NL, P, PL, S, SK, SLO, TR
*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. 24/25 Shure Incorporated S8 823-832 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich BG, CH, D, DK, EST, F, FIN, IS, N, NL, S license free*
A, B, CY, CZ E, GB, GR, H, HR I, IRL, LV, L, LT, M, P, PL SK, SLO, RO, TR
*
*
*
*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. T11 863-865 MHz Country Code Code de Pays Codice di paese Cdigo de pas Lnder-Krzel A, B, BG, CH, CY, CZ, D, DK, E, EST F, FIN, GB, GR, H, HR, I, IRL, IS, L, LT LV, M, N, NL, P, PL, S, SK, SLO TR Frequency Range Gamme de frequences Gamme di frequenza Gama de frequencias Frequenzbereich license free license free license free 863 - 865 MHz*
* This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information. 25/25