Shure Incorporated GLXD6+
Set Up the Receiver 1. 2. 3. Connect the power supply to the receiver and plug the cord into an AC power source. Connect the transmitter to the instrument. Connect the audio output to an amplifier or mixer. Install Transmitter Batteries 1. 2. 3. Move the locking lever to the open position and slide the battery door open. Place the battery into the transmitter. Close the battery door. System Set Up Important: Before beginning, turn off all receivers and transmitters. Turn on and link each receiver/transmitter pair one at a time to prevent cross-linking. 1. 2. Turn on a receiver. Press and hold the group button to select a group (if necessary). If the group is already set, press the channel button to scan for the best available channel. 3. Turn on a transmitter. The blue RF LED will flash while the transmitter and receiver form a link. When the link has suc cessfully formed, the RF LED will remain illuminated. The transmitter and receiver will remain linked for future usage. Repeat steps 1-3 for each additional receiver and transmitter. Remember to set each receiver to the same group. 3/14 Shure Incorporated Note: Dashes appearing on the group and channel display after a channel selection indicate that frequencies are not available in the selected group. Choose a group that supports more receivers and repeat the linking steps. Linking Two Transmitters to a Receiver Only one transmitter can be active at a time to prevent cross interference. Gain settings for each transmitter can be indepen dently set and stored when the transmitter is active. Important! Do not turn on and operate both linked transmitters at any time. Turn off both transmitters before beginning. 1. Press the group button to select a group. The receiver automatically scans the selected group to find the best available channel. 2. 3. Turn on transmitter 1 and link it to the receiver. Adjust the gain, and then turn off the transmitter. Turn on transmitter 2 and press and hold the link button to link it to the receiver. Adjust the gain, and then turn off the transmitter. Identifying Linked Transmitters and Receivers with Remote ID Use the remote ID feature to identify linked transmitter and receiver pairs in multiple receiver systems. To activate remote ID:
1. 2. Momentarily press the link button on the transmitter or receiver. The screen of the linked receiver will blink and display ID, while the status LED on the linked transmitter will flash red/
green. 3. To exit remote ID mode, momentarily press the link button or allow the function to timeout. Locking and Unlocking the Controls The controls of the receiver and transmitter can be locked to prevent accidental or unauthorized changes to settings. The following parameters are not affected by locking the controls:
Lock status is not changed by power cycles Tuner functionality and editing remains available The receiver power switch does not lock 4/14 Shure Incorporated Locking the Receiver Controls Simultaneously press and hold the group and channel buttons until LK appears on the screen. Repeat to unlock. LK is displayed if a locked control is pressed UN is displayed momentarily to confirm the unlock command Locking the Transmitter Power Switch To lock directly from the transmitter:
Start with the transmitter off, then press and hold the link button while turning on the transmitter. Continue to hold the link but ton until the lock icon appears on the receiver screen. Repeat sequence to unlock. To lock from the receiver front panel:
Simultaneously press and hold the group and link buttons for approximately 2 seconds until the flashing lock icon appears on the receiver screen. Repeat sequence to unlock. Note: The transmitter status LED will flash red/green if a locked switch is set to the off position. Firmware New versions of the firmware can be uploaded and installed using the Shure Update Utility tool. Download Shure Update Utility from shure.com Specifications Tuning Bandwidth 24002483.5 MHz Working Range Indoor Outdoor Transmit Mode Shure proprietary digital Audio Frequency Response 20 Hz 20 kHz Dynamic Range 120 dB, Aweighted RF Sensitivity 88 dBm, typical Up to 30 m ( 100 ft) typical, Up to 60 m
( 200 ft) maximum Up to 20 m ( 65 ft) typical, Up to 50 m ( 165 ft) maximum 5/14 Shure Incorporated Total Harmonic Distortion 0.2%, typical RF Output Power 10 mW E.I.R.P. max Operating Temperature Range
-18C (0F) to 57C (135F) Storage Temperature Range
-29C (-20F) to 74C (165F) Polarity Positive voltage applied to the tip of the guitar cable phone plug produces positive voltage at the tip of the high impedance -inch output. Battery Life Up to 11.5 hours Guitar Tuner Tuning Accuracy Tuning Range Channel Count 4 typical, Up to 8 maximum GLXD1 Dimensions 1 cent F#0 to C8 90 x 65 x 23 mm( 3.56 x 2.54 x 0.90in.), H x W x D (without antenna) Weight 132 g (4.7 oz.) without batteries Power Requirements 3.7 V Rechargeable Li-Ion Housing Cast Metal, Black Powdercoat Input Impedance 900 k RF Output Power 10 mW E.I.R.P. max 6/14 Transmitter Input Connector 4-Pin male mini connector (TA4M) Shure Incorporated Configuration Unbalanced Maximum Input Level 1 kHz at 1% THD
+8.4 dBV (7.5 Vpp) Antenna Type Internal Monopole Pin Assignments TA4M 1 2 3 4 ground (cable shield)
+ 5 V Bias audio Tied through active load to ground (On instrument adapter cable, pin 4 floats) GLXD6 Dimensions 46 x 95 x 133 mm (1.8 x 3.7 x 5.2 in.), H x W x D Weight 504 g(17.8 oz.) 7/14 Housing Cast Metal, Black Powdercoat Power Requirements 9 to 15 V DC, 250 mA min. Spurious Rejection
>35 dB, typical Gain Adjustment Range 20 to 40 dBin 1 dB steps Audio Output Configuration 6.35 mm (1/4") output Impedance 6.35 mm (1/4") output Maximum Audio Output Level Shure Incorporated Impedance balanced 100 (50 , Unbalanced) 6.35 mm (1/4") connector (into 3 k load)
+8.5 dBV Tip=audio, Ring=no audio, Sleeve=ground Pin Assignments 6.35 mm (1/4") connector Receiver Antenna Input Impedance 50 Antenna Type PIFA antennas Maximum Input Level 20 dBm 8/14 Output Connections Shure Incorporated IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturers instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in cluding amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec tion. 9/14 Shure Incorporated 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure. 21. Operate this product within its specified operating temperature range. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accom panying this unit. In the European Union and the United Kingdom, this label indicates that the batteries in this product should be collected sepa rately and not be disposed of with household waste. Substances in batteries can have a potential negative impact on health and environment and you have a role in recycling waste batteries thus contributing to the protection, preservation, and im provement of the quality of the environment. You should contact your local authority or retailer for details of the collection and recycling schemes available. Please consider the environment, electric products and packaging are part of regional recycling schemes and do not belong to regular household waste. WARNING Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140F (60C), or incinerate. Follow instructions from manufacturer Only use Shure charger to recharge Shure rechargeable batteries WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type. Never put batteries in mouth. If swallowed, contact your physician or local poison control center Do not short circuit; may cause burns or catch fire Do not charge or use battery packs other than Shure rechargeable batteries Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like Do not immerse the battery in liquid such as water, beverages, or other fluids. Do not attach or insert battery with polarity reversed. Keep away from small children. Do not use abnormal batteries. Pack the battery securely for transport. Note:
This equipment is intended to be used in professional audio applications. EMC conformance is based on the use of supplied and recommended cable types. The use of other cable types may de grade EMC performance. Use this battery charger only with the Shure charging modules and battery packs for which it is designed. Use with other than the specified modules and battery packs may increase the risk of fire or explosion. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equip ment. 10/14 Shure Incorporated Information to the user This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. 2. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Certified under FCC Part 15. Shure has determined that this product is a Class B harmonized product. The following sections provide country-specific EMC/
EMI or product safety information. Certifications FCC ID: DD4GLXD6Z3 IC: 616A-GLXD6Z3 CAN ICES-003 (B)/NMB-003(B) Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites dexposition au rayonnement ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Certified by ISED in Canada under RSS-247 and RSS-GEN. This device contains licenceexempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop ment Canadas licenceexempt RSS(s). Operation is subject to the following two conditions:
1. 2. This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. 2. Lappareil ne doit pas produire de brouillage;
Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 11/14 Shure Incorporated This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites dexposition aux rayonnements ISED tablies pour un environnement non contrl. Lutilisateur final doit suivre les instructions spcifiques pour satisfaire les normes. Cet metteur ne doit pas tre coimplant ou fonctionner en conjonction avec toute autre antenne ou transmetteur. La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas dev idamente autorizados. Paraguay Distributor: Microsystems S.R.L., Senador Long 664 c/Dr. Lilio, Asuncin, Paraguay Connection and use of this communications equipment is permitted by the Nigerian Communications Commission. 1. 2. 3. Shure http://www.shure.co.jp 12/14 Shure Incorporated 2.4GHz DS-SS FH-SS 40m 2,400MHz 2,483.5MHz Waste Electrical and Electronic Equipment (WEEE) Directive In the European Union and the United Kingdom, this label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. REACH (Registration, Evaluation, Authorization of Chemicals) is the European Union (EU) and the United Kingdom (UK) chemical substances regulatory framework. Information on substances of very high concern contained in Shure products in a concentration above 0.1% weight over weight (w/w) is available upon request. CE Notice: Hereby, Shure Incorporated declares that this product with CE Marking has been determined to be in compliance with European Union requirements. The full text of the EU declaration of conformity is available at the following site: https://
www.shure.com/en-EU/support/declarations-of-conformity. Authorized European representative:
Shure Europe GmbH Department: Global Compliance Jakob-Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: +49-7262-92 49 0 Fax: +49-7262-92 49 11 4 Email: EMEAsupport@shure.de UKCA Notice: Hereby, Shure Incorporated declares that this product with UKCA Marking has been determined to be in compli ance with UKCA requirements. The full text of the UK declaration of conformity is available at the following site: https://
www.shure.com/en-GB/support/declarations-of-conformity. UK Importer / UK Rep. Shure UK Limited Unit 2, The IO Centre, Lea Road, Waltham Abbey, Essex, EN9 1 AS, UK 13/14 ISM Shure Incorporated 14/14