all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual | Users Manual | 1.64 MiB | ||||
1 | Test Report | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | Parts List/Tune Up Info | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Manual | Users Manual | 1.64 MiB |
Model PSM 200 User Guide PSM 200 Personal Monitor System User Guide Guide de lutilisateur du systme de retour personnel Bedienungsanleitung fr das InEarAbhrsystem Gua del usuario del sistema de monitoreo personal Guida all'uso del sistema di monitoraggio personale Manual do Usurio do Sistema de Monitorao Pessoal
>>E2
>>P2R 2002, Shure Incorporated 27a8792 (BA)
>>P2T Printed in U.S.A. Declaration of Conformity We of Shure Incorporated 222 Hartrey Ave. Evanston IL 602023696 U.S.A. 8478662200 declare under our sole responsibility that the following products, Model: P2R Name: P2R Receiver were tested and found to comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Testing was completed by the following NVLAP or A2LA accredited laboratory:
L. S. Compliance, Inc. W66 N220 Commerce Ct. Cedarburg, Wisconsin 53012 U.S.A. At the test location of L. S. Compliance, Inc. W66 N220 Commerce Ct. Cedarburg, Wisconsin 53012, U.S.A. Shure Incorporated., Manufacturer. Signed:
Date: March 04, 2002 Name, Title: Craig Kozokar, EMC Project Engineer Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
S S S S Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3 ENGLISH WARNING!
USING THIS SYSTEM AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE. In order to use this system safely, avoid prolonged listening at excessive sound pressure levels. Please use the fol-
lowing guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure levels before hearing damage occurs. 90 dB SPL at 8 hours 95 dB SPL at 4 hours 100 dB SPL at 2 hours 105 dB SPL at 1 hour 110 dB SPL at 1/2 hour 115 dB SPL at 15 minutes 120 dB SPL avoid or hearing damage may occur It is difficult to measure the exact Sound Pressure Levels (SPL) present at the eardrum in live applications. In addition to the volume setting on the PSM, the SPL in the ear is affected by ambient sound from floor wedges or other devices. The isolation provided by the fit of quality earphones is also an important factor in determining the SPL in the ear. Here are some general tips to follow in the use of this product to protect your ears from damage:
1. Turn up the volume control only far enough to hear properly. 2. Ringing in the ears may indicate that the gain levels are too high. Try lowering the gain levels. 3. Have your ears checked by an audiologist on a regular basis. If you experience wax buildup in your ears, stop using the system until an audiologist has examined your ears. 4. Wipe the earphones with an antiseptic before and after use to avoid infections. Stop using the earphones if they are causing great discomfort or infection. This symbol indicates important operating and maintenance instructions in the literature accompanying this unit. FCC Statement. The P2R receiver complies with part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) this device does not cause harmful interference, and (2) this device must accept any interference received, in-
cluding interference that may cause undesired operation. LICENSING INFORMATION Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the users responsibility, and licensability depends on the users classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licens-
ing, and before choosing and ordering frequencies. IMPORTANT!
THIS RADIO EQUIPMENT IS INTENDED FOR USE IN PROFESSIONAL ENTERTAINMENT (CLASS I) AND SIMILAR APPLICA-
TIONS. NOTE: THIS EQUIPMENT MAY BE CAPABLE OF OPERATING ON SOME FREQUENCIES NOT AUTHORIZED IN YOUR REGION. PLEASE CONTACT YOUR NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES FOR WIRE-
LESS MICROPHONE PRODUCTS IN YOUR REGION Licensing: Note that a ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. 1 TABLE OF CONTENTS ENGLISH QUICK SET-UP GUIDES PSM200 Wireless System P2R Receiver Quick Set-Up Guide:
. INTRODUCTION
. The PSM200 Personal Monitor System Features 5 5 6 7 7 7 THE P2T TRANSMIXER Controls and Features Audio Inputs and Outputs Phantom Power Selecting a Frequency Channel
. 8 8 8 8 8 P2R RECEIVER
. Controls and Features Battery Installation Cable Management Groove Wireless Mode Wired Mode CHANNEL LED MIX IN Jack LIM LED 9 9 9 9 10 10 10 10 10 SET-UP
. Wireless System Set-Up Hybrid Wired/Wireless System Set-Up P2R Stand-Alone Wired Set-Up 11 11 11 11 SYSTEM APPLICATIONS APPLICATION ONE: Wireless Set-Up for a Vocalist APPLICATION TWO: Combination Wired and Wireless Set-Up for a Drummer APPLICATION THREE: Two PSM200 Wireless Systems Used Simultaneously
. 12 12 12 13 RACK MOUNTING THE P2T
. 13 TROUBLESHOOTING
. 14 ACCESSORIES
. 14 SPECIFICATIONS System Specifications P2T TransMixer Specifications P2R Receiver Specifications PSM200 Channel Frequencies
. 14 14 15 15 15 CERTIFICATIONS
. 16 APPENDIX
. P2R Receiver MIX IN Jack Wiring Diagrams 16 16 2 QUICK SET-UP GUIDES PSMR200 Wireless System ENGLISH The following set-up illustration is for the complete PSM200 Wireless System, which includes the P2T TransMixer, the P2R Receiver, and the E2 Earphones. If you have purchased the P2R as a stand-alone wired personal monitor, see page 6. 1. Plug in the power supply and connect it to the DC input on the rear panel of the P2T TransMixer. 2. Insert a 9 Volt battery into the P2R Receiver, observing proper polarity. PSM200 TransMixer MIC/LINE1 MIC/LINE2 1 INPUTS 2 CHANNEL SELECT Mixing Console 3. Connect audio sources to the MIC/LINE INPUTS on the front 6. Check the RF LED on the top of the Receiver to 4. 5. panel of the TransMixer. Turn the Receiver volume knob clockwise past the click (ON). Keep the volume at a low setting. Set the TransMixer and Receiver to the same frequency chan-
nel. See the Selecting a Frequency Channel section on page 8. 7. 8. confirm that it is receiving signal from the TransMixer. Plug the Earphones into the earphone jack on the Receiver. Insert the Earphones into your ears. Increase Receiver volume until the knob is turned to approximately 11 oclock. PSM200 TransMixer MIC/LINE1 MIC/LINE2 1 INPUTS 2 CHANNEL SELECT Mixing Console 9. On the front panel of the TransMixer, adjust the signal level of each audio input with the INPUT knobs. 10. Check the INPUT LEDs on the TransMixer to verify that signal is present, but not clipping. See the Audio Inputs and Outputs section on page 8 for details. 11. Slowly adjust the Receiver volume to a comfortable level. 3 P2R Receiver Quick Set-Up Guide:
When Used as a Wired Stand-Alone Personal Monitor ENGLISH Mixing Console 1. Insert a 9 Volt battery into the P2R Receiver, observing proper polarity. 2. Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R. 3. Turn the P2R volume knob on (past the click). Keep the volume at a low setting. 4. Set the CHANNEL to A with the SELECT Button. See the Wired Mode section on page 10 for details. 5. Set the GAIN switch to LOW initially and set your source volume to a moderate level. 6. Attach the P2R onto your belt, waistband, or another location and slide the cable into the cable management groove on the back side of the unit. Plug Earphones into the earphone jack on the P2R. Insert the Earphones into your ears. Slowly adjust the volume to a comfortable level. Set the GAIN switch to HIGH if the signal level is too low. Mixing Console 7. 8. 4 INTRODUCTION ENGLISH Thank you for buying the PSM200. Like all Shure PSM personal monitoring products, the PSM200 provides the many advantages of in-ear monitoring including:
S S S Improved Sound Quality high fidelity without the risk of feedback, Increased Mobility your mix moves with you, Personal Control create a personal mix, and control your own levels. For information on this and other Shure products, visit www.shure.com on the World Wide Web. crophones or instruments directly to the inputs, use line out-
puts from a mixing console, or connect it to Shures Aux-
Pandert. In short, no matter what the output device, you can probably plug it into the TransMixer. The complete PSM200 System includes the E2 Earphones, which feature a dynamic driver that produces crisp, full-spec-
trum sound. They include a variety of sleeve options to provide the best fit and isolation for your ears. The E2, like all Shure earphones, work well with CD players, MP3 players, and any-
thing else with a 1/8-inch (3.5mm) stereo output. S Mono mix S S S S S Up to 4 systems can be operated simultaneously Input level controls Tricolor LED input level indicators 1/4-inch line-level input jack to connect monitor mix, click tracks, effects, or condenser microphones. Integrated cable management groove secures cables con-
nected to the bodypack. The PSM200 Personal Monitor System The PSM200 is a frequency-agile, in-ear monitor system for use in a wide variety of applications. Its many features help overcome the difficulties associated with stage monitoring. The P2R Receiver is the worlds first bodypack receiver to function as a wired receiver, a wireless receiver, or both at the same time. This and other unique features, along with excellent sound quality, make the P2R an exceptional value. The P2T TransMixer is another breakthrough design for in-ear monitoring. It allows the user to connect two line-level or miclevel inputs directly into the transmitter. The two sig-
nals can then be mixed independently. You can connect mi-
Features PSM200 System S 8 selectable UHF frequencies S Includes E2 dynamic-driver earphones P2T TransMixer 2 mic/line XLR/1/
S XLR SPLIT OUT connectors S 4-inch combo inputs P2R Receiver S Combination wired/wireless compatibility S Gain switch for setting line input sensitivity 5 THE P2T TRANSMIXER Controls and Features 1 2 4 5 ENGLISH FRONT PANEL:
BACK PANEL:
6 3 7 8 9 1. MIC/LINE INPUT Jacks: Electronically balanced inputs that accommodate both XLR and 1/4-inch connectors at mic or line levels. 2. Signal/Clip LEDs: Color indicates the signal status of the corresponding MIC/LINE input, as explained in the Audio Inputs and Outputs section below. INPUT Knobs: Control the level of their corresponding inputs. 3. 4. CHANNEL LED Indicator: Displays the frequency chan-
nel that is being transmitted (18). 5. SELECT Button: Press to select a frequency channel. 6. Antenna: Permanently mounted, breakresistent anten-
na transmits the mix to the P2R Receiver. 7. Power Cord Strain Relief: Thread the power cable through these slots to secure the DC connection. 8. DC IN: Plug the power supply into this connector. The unit remains powered on until you unplug it. 9. SPLIT OUTs: Each male XLR output jack duplicates the signal of the corresponding mic/line input. Front panel set-
tings have no effect on split output level. Audio Inputs and Outputs The INPUT knobs control both MIC and LINE level signals. As a general guide-
line, set the knob to the left of twelve oclock for line level signals, and to the right of twelve oclock for microphone levels. Observe the signal/clip LEDs. If they are consistently red, decrease the level with the corresponding INPUT knob. INPUT LED RED YELLOW GREEN Limited Signal*
Nominal Level Signal Present NOTE: If the level is decreased all the way and the LED remains red, the level of the input from the previous device in the audio chain (mixer, click track, digital sequencer, etc.) is too high and should be decreased. Line Level INPUT Knob Microphone Level To pass audio signal directly through the TransMixer, use the corresponding SPLIT OUT on the rear panel of the device. Input settings do not affect the level of the signal at the SPLIT OUT connectors.
* The P2T inputs have limiting circuitry that activates automatically when the input level is too high. Phantom Power Although the TransMixer itself does not provide phantom power for condenser microphones, the SPLIT OUT connectors pass phantom pow-
er from a phantom power supply to a microphone connected to the corresponding input jack. You can connect equipment that supplies phan-
tom power to the TransMixer without harming the unit. Selecting a Frequency Channel 1. Press and hold the SELECT button until the CHANNEL LED indicator begins to flash. 2. When the LED indicator is flashing, press the SELECT button to scroll to the desired frequency channel. 3. Release the button. After 4 seconds the display will stop flashing and the P2T will automatically switch to the specified channel. IMPORTANT:
Never set more than ONE TransMixer to the same frequency channel, or interference will occur. 6 P2R RECEIVER Controls and Features ENGLISH 1 2 3 4 7 8 9 10 5 6 1. POWER LED: Lights to indicate the unit is powered on and blinks to indicate low battery. When this LED starts blinking, you have approximately 15 minutes of battery time remaining. 2. On/Off/Volume Knob: Turn clockwise past click to power on. Continue to turn clockwise to increase vol-
ume, counterclockwise to decrease volume. 3. LIM LED: Lights only when limiter is activated. See the LIM LED section on page 10 for details. 4. RF LED: Lights when the unit is receiving radio frequency
(RF) signal from the P2T TransMixer. 5. Antenna: An attached, flexible whip antenna receives RF signal from the TransMixer. 6. CHANNEL LED Indicator: Displays the number of the current frequency channel (1-8), or the letter A for wired mode. See the CHANNEL LED Indicator section on page 10 for details. Battery Installation 12 11 13 7. SELECT Button: Press to increment the frequency channel or set to A for wired mode. 8. MIX IN Jack: Connect a 1/4-inch line-level input to this jack. Use alone, or in combination with wireless recep-
tion from the P2T Transmixer. See the MIX IN Jack section on page 10 for details. 9. GAIN Switch: Slide to HI or LO position to set the sensi-
tivity of the MIX IN input. 10. Earphone Output Jack: Connect E1, E2, or E5 ear-
phones to this 1/8-inch (3.5mm) jack. 11. Cable Management Groove: For a secure connection, guide the cable connected to the MIX IN Jack or the earphone cord into this groove. 12. Belt Clip: Securely attaches the unit to a belt, guitar strap or waist band. 13. Battery Compartment Door: See the Battery Installa-
tion section below. 1. Unlock the battery compartment door by pressing down on the side of the battery compartment door marked OPEN and sliding it in the direction of the arrow. 2. Flip open the door and insert a fresh 9V alkaline battery, observing proper polarity. 3. Flip the battery compartment door closed, then press and slide the compartment door until it snaps shut. Note: If the battery compartment door will not close completely, the battery is not correctly inserted. Cable Management Groove 1. Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R. 2. Attach the P2R to your belt, waist band, or another location. 3. Slide the audio cable or earphone cord up into the groove, as illustrated. 4. The belt clip will hold them securely in place. 7 Wireless Mode ENGLISH When you are using the P2R as a wireless receiver, or as a combination wired and wireless receiver, use the SELECT button on the side of the P2R Receiver to set the frequency channel (18). To Select a Frequency Channnel:
1. Press and hold the SELECT button until the CHANNEL LED indicator begins to flash. 2. When the LED indicator is flashing, press the SELECT button to scroll to the desired frequency channel. 3. Release the button. After 4 seconds the display will stop flashing and the P2R will automatically switch to the specified channel. NOTE: Set the P2R to the same channel as the P2T TransMixer. Wired Mode When you are using the P2R Receiver as a stand-alone wired monitor, you can set the unit to wired mode. This de-activates the RF circuitry and extends the battery life. To Set the P2R to Wired Mode:
1. Press and hold the SELECT button until the CHANNEL LED indicator begins to flash. 2. When the LED indicator is flashing, press the SELECT button to scroll past channel 8 until the letter A appears in the display. 3. Release the button. After 4 seconds the display will stop flashing and the P2R will automatically switch to wired mode. NOTE: Setting the P2R receiver to wired mode disables its wireless capability. CHANNEL LED Indicator The CHANNEL LED indicator shuts itself off after 10 seconds to conserve battery life. To view the frequency channel when the LED indicator is off, simply press and release the SELECT button. To disable the battery saving feature:
1. Turn off the P2R. 2. Press and hold the SELECT button and turn the unit back on while holding down the button. 3. The LED indicator now displays the current frequency channel until you turn off the P2R and turn it back on. MIX IN Jack When you are using the P2R Receiver as a stand-alone personal monitor, the 1/4-inch MIX IN jack serves as the primary audio input. In addition, the MIX IN jack allows the P2R to function as a hybrid wired and wireless receiver. When you are using the P2R in its wireless mode, you can add a second audio source via the MIX IN jack, such as. S S Click Tracks Pre-Amp Outputs from Guitar or Bass S Effects Processors Condenser Microphones S Next to the jack is a two-position GAIN switch that gives you a choice between LO and HI gain settings for the input. For specific information on how the MIX IN jack functions, refer to the wiring diagrams on page 16. LIM LED The P2R Receiver has a nondefeatable (constantly active) limiter that automatically activates if the receiver output level exceeds a certain volume, which is calibrated specifically for the Shure E2 earphones. The LIM LED on the top of the unit lights up when the limiter is on. If the LIM LED blinks occasionally, turn down the volume of the receiver.* If the LED is on and you havent reached a high enough listening level, try re-inserting the earphones for a better seal, or adjust the mix that is being sent to the receiver to include only the most essential inputs.**
* When the LED is on, the volume will not increase.
** The limiter is designed to work best with the Shure E2 earphones. Using the P2R with Shure E1 or E5, or earphones made by other manufacturers, can result in higher limited volume levels. 8 ENGLISH SET-UP Wireless System Set-Up To configure the P2T TransMixer and P2R Receiver for wireless operation:
5. To pass audio signal directly through the TransMixer, use the corresponding SPLIT OUT connector on the rear panel of the device. Turn the On/Off/Volume knob on the P2R clockwise past click
(On). Leave the volume setting low. 6. 7. Set the P2R to the same frequency channel as the P2T. 8. Check the RF LED on the P2R to confirm that transmission is being received. 9. Plug earphones into the earphone output jack. Insert the earphones into your ears as instructed in the earphone users guide. 10. Slowly increase the P2R volume to a comfortable level. 1. Plug the power supply into the DC INPUT connector on the rear panel of the P2T, then plug it into a power outlet. 2. Connect audio sources to the combo XLR/1/4-inch jacks on the front panel. 3. Select a frequency channel (18). See the Selecting a Fre-
quency Channel section on page 8 for details. IMPORTANT: Never set more than ONE TransMixer to the same frequency channel, or interference will occur. 4. Observe the signal/clip LEDs. If they are consistently red, decrease the level with the corresponding INPUT level knob. PSM200 TransMixer MIC/LINE1 MIC/LINE2 1 INPUTS 2 CHANNEL SELECT Mixing Console Hybrid Wired/Wireless System Set-Up To configure the P2T TransMixer and P2R Receiver for hybrid wired/wireless operation:
1. Follow steps 19 of the Wireless System Set-Up section. 2. Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R. 4. Attach the P2R onto your belt, waistband, or another location. 5. Slide the audio cable or earphone cord into the cable man-
agement groove. 3. Set the GAIN switch to LOW initially and set the source volume to a moderate level. 6. Slowly increase the P2R volume to a comfortable level. Set the GAIN switch to HIGH if you need more level. P2R Stand-Alone Wired Set-Up*
To configure the P2R Receiver as a stand-alone personal monitor:
1. Turn the On/Off/Volume knob clockwise past click (On). Leave the volume setting low. 2. Set the CHANNEL to A with the SELECT Button. See the Wired Mode section on page 10 for details. 3. Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R. 4. Set the GAIN switch to LOW initially and set the source volume to a moderate level. 5. Attach the P2R onto your belt, waistband, or another location. 6. Slide the audio cable or earphone cord into the cable management groove. 7. Plug the earphones into the earphone output jack. Insert the earphones into your ears as instructed in the ear-
phone users guide. 8. Slowly increase the P2R volume to a comfortable level. Set the GAIN switch to HIGH if you need more level. Mixing Console NOTE: Setting the P2R receiver to A disables its wireless capability and extends the battery life.
* If you have purchased the P2R as a stand-alone personal monitor, you can go wireless by simply purchasing a P2T TransMixer. 9 ENGLISH SYSTEM APPLICATIONS This section presents three typical applications for the PSM200. For more ideas, visit Shures website at www.shure.com. APPLICATION ONE: Wireless Set-Up for a Vocalist This is the basic wireless configuration of the PSM200 system for a single user, either instrumental or vocal:
1. Connect the vocal mic to INPUT 1 of the P2T TransMixer. 2. Connect SPLIT OUT 1 from the P2T to the Mixing Console. 3. Connect the instrumental mix line out to INPUT 2 of the P2T. 4. Set the P2T and P2R to the same frequency channel. 5. Insert the E2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer. Wireless Transmission Vocal Mic Signal SPLIT OUT from TransMixer Band Mix Vocal Mic Mixing Console APPLICATION TWO: Combination Wired and Wireless Set-Up for a Drummer The following application uses the P2R as a combination wired/wireless Receiver. The MIX IN jack of the P2R is connected to a click track for the drummer:
1. Connect the drum mix out of the Mixing Console to INPUT 1 of the P2T TransMixer. 2. Connect the band mix out of the Mixing Console to INPUT 2 of the P2T. 3. Set the P2T and the P2R to the same frequency channel. 4. 5. Set the P2R Receiver to a comfortable level. 6. Set the GAIN switch on the P2R to LOW. 7. Connect the Click Output to the MIX IN 1/4-inch jack of the P2R and adjust your levels. Insert the E2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer. Band Mix Drum Mix Mixing Console Click Track 10 ENGLISH APPLICATION THREE: Two PSM200 Wireless Systems Used Simultaneously*
The following configuration uses two PSM200 systems simultaneously, and utilizes the SPLIT OUT feature of the TransMixer. In this exam-
ple, the musicians keep the TranMixers on stage with them, in order to control their personal mixes independent of the house engineer. 1. Connect the vocal mic to INPUT 1 of the Vocal Mix TransMixer and connect SPLIT OUT 1 (the vocals) to the Mixing Console. 2. Connect the total band mix from the Mixing Console to INPUT 2 of the Vocal Mix TransMixer. NOTE: In this example, the band mix includes vocals. This allows the guitar mix to include vocals, and allows the vocalist to independently control more of the vocal level in his/her personal mix. 3. Set the Vocal Mix P2T and P2R Receiver to the same frequency channel. 4. Connect SPLIT OUT 2 of the Vocal Mix TransMixer (the band mix) to INPUT 1 of the Guitar Mix TransMixer. 5. Connect the guitar amp simulator to INPUT 2 of the Guitar Mix P2T TransMixer. 6. Connect the SPLIT OUT 2 of the Guitar Mix TransMixer (the guitar amp simulator) to the Mixing Console. 7. Set the Guitar Mix P2T TransMixer and P2R Receiver to a frequency channel thats different from the channel you set for the Vocal Mix system in step 3.
* Up to four systems can be used at the same time. Vocal Mic SPLIT OUT from TransMixer Band Mix SPLIT OUT from TransMixer Guitar Mix Vocal Mix Guitar Amp Simulator Band Mix Vocal Mic Vocal Mix Mixing Console Guitar Mix Guitar Amp Simulator SPLIT OUT from TransMixer RACK MOUNTING THE P2T The P2T features a standard 1/2rack space design, and includes a rack mounting kit. WARNING: Do not torque the screws too tightly, or the chassis may be damaged. Install Rack Ears Single Unit PSM200TransMixer MIC/LINE 1 MIC/LINE 2 1 INPUTS2 CHANNELSELECT Mount in an Equipment Rack DualMounting Two Units PSM200TransMixer PSM200TransMixer MIC/LINE 1 MIC/LINE 2 1 INPUTS2 CHANNELSELECT MIC/LINE 1 MIC/LINE 2 1 INPUTS2 CHANNELSELECT PSM200TransMixer PSM200TransMixer PSM200TransMixer MIC/LINE1 MIC/LINE2 1 INPUTS 2 CHANNELSELECT MIC/LINE 1 MIC/LINE 2 1 INPUTS 2 CHANNELSELECT MIC/LINE1 MIC/LINE 2 1 INPUTS2 CHANNELSELECT NOTE: Be sure to use both straddle bars when installing dual units. 11 TROUBLESHOOTING ENGLISH PROBLEM SOLUTION No sound at the receiver n Check the power cord on the TransMixer and make sure it is powered on. n Make sure both the TransMixer and the P2R Receiver are set to the same frequency channel. n Make sure the earphones are plugged in to the receiver and the volume is up. n Make sure the Receiver is on and the battery is good. n Check the incoming audio connections on the TransMixer. Low receiver range n Try to maintain line-of-sight between the TransMixer and Receiver antennas. n Try another frequency in case interference is limiting the range. n Check for television channel interference. More information is available at www.shure.com. Receiver sounds fuzzy or distorted n Make sure no other TransMixers or wireless transmitters are oper-
ating on your frequency. n Make sure the TransMixer input level is lighting yellow LEDs for optimum performance. n Make sure you are using a fresh battery in the P2R. Low audio output at the receiver n Make sure the TransMixer input level is lighting yellow LEDs for optimum performance. n Make sure the P2R Receivers volume knob is up. ACCESSORIES Furnished Accessories P2T TransMixer AC Adaptor Rack Mount Kit
. PS20, PS20E, PS20UK 53B8484 Optional Equipment AuxPander:
The Shure AuxPander auxiliary expander extends the capabili-
ties of a standard mixing console by providing eight additional auxiliary sends. It is designed ideally for use with multiple per-
sonal monitoring systems. P4M:
The P4M is a highly versatile fourchannel, twobus stereo mic/line mixer designed to optimize personal (inear) monitor systems in live performance applications. SPECIFICATIONS PSM200 System RF Carrier Frequency Range 518865 MHz (country dependent) Operating Range 100 m (300 ft.) under optimal conditions Audio Frequency Response 30 Hz to 12 kHz (+/3 dB); earphone dependent Total Harmonic Distortion (1 KHz)
<1% typical (Ref. 35 kHz deviation) P2R Receiver 1/4inch mono 20 foot cable
. 90B4677 AP200:
You can use the AP200 adaptor to connect a lavalier micro-
phone to the MIX IN jack on the P2R Receiver. The AP200 includes a Shure WL93 omnidirectional microphone that al-
lows you to combine your wireless mix with ambient sound from your surroundings. Modulation FM 35 kHz Deviation (Nominal) Signal-to-Noise Ratio 80 dB typical (A-weighted) Operating Temperature 7 C to +49 C
(+20 F to +120 F) 12 P2T TransMixer RF Output Power ENGLISH P2T Audio Outputs 30 mW (+15 dBm) typical conducted (country dependent) Passive connection parallel with input. Modulation Limiter Internal peak limiter (>10:1 hard knee compression) Antenna 1/4 Wavelength, semi-rigid, PCB Mount Current 170 mA maximum Dimensions 220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.) Net Weight 370 g (13 oz.) P2T Audio Input Connector Type:
Configuration:
Actual Impedance:
Nominal Input Level:
Maximum Input Level:
Pin Assignments:
XLR/1/4-inch combo electronically balanced 1 k 25 dBu @ 1/2 volume
(12 oclock) 5 dBu @ 1/2 volume
(12 oclock) XLR: 2=hot; 3=cold, 1=ground 1/4: Tip = hot, Ring = cold, Sleeve=ground Phantom Power Protection?
Yes: Up to 52 VDC P2R Receiver RF Sensitivity 109 dBm typical Squelch Threshold 102 dBm typical Antenna Attached Whip Audio Input Connector Connector Type:
Impedance:
Maximum Input Level:
1/4-inch Mono 1 M LOW = +0 dBu HIGH = 10 dBu Connector Type:
Configuration:
XLR electronically balanced Pin Assignments:
2 = hot ; 3 = cold, 1 = ground Phantom Power Protection?
Yes: Up to 52 Vdc Power Requirements S Operating voltage 1218 Vdc Supplied with one of the following external power supplies:
Model PS20: 120 VAC, 60 Hz input, UL and cUL approvals. Model PS20E, Model PS20UK: 230 VAC, 50/60 Hz input, TUV approval with European CE marking, conforms to European Low Voltage Directive 72/23/EEC. S Power Requirements 9 V alkaline battery, DuracellR type MN1604 recommended Battery Life Volume Dependent Wired (RF Off):
Wireless (RF On):
6 hours 4 hours Audio Output Connector Minimum Load Impedance 1/8 inch (3.5 mm) 8 Net Weight 100 g (3.52 oz.), less battery Overall Dimensions 122 mm x 73 mm x 32 mm
(4.809 in. x 2.875 in. x 1.251 in.) PSM200 Channel Frequencies The PSM200 is available in four frequency groups, each coordinated to work in a specific geographic region. You can find the frequency group for your system printed on the rear panel of the P2T TransMixer. For more information on which frequencies can be used in your area, call our Applications Group at 8478662525, or visit the Technical Support section at www.shure.com. CHANNEL H2
(518554)MHz North America, Europe 1 2 3 4 5 6 7 8 518.750 524.875 525.625 534.375 536.875 538.500 551.000 553.250 R8
(800814)MHz Europe 801.100 802.325 805.050 808.600 810.550 811.600 813.300 813.800 Q3
(748784)MHz France, Australia 749.100 754.025 756.000 765.900 772.000 775.000 778.775 781.900 S5
(842865)MHz England 855.275 856.175 857.625 858.200 863.075 863.625 864.425 864.850 Channel A (P2R Only) Wired Mode (RF Disabled) 13 ENGLISH PS20: Conforms to Safety Standards UL1310 and Canada/CSA22.2, No. 223 PS20E: Conforms to Safety Standard EN 60065. PS20UK: Conforms to Safety Standard EN 60065 and BS 7002. SHURE P2R Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Outside the United States, return the product to your dealer or Authorized Service Center. This warranty does not apply in cases of abuse or misuse of the product, use contrary to Shures instruction, or unauthorized re-
pair. All implied WARRANTIES OF MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE are hereby dis-
claimed and Shure hereby disclaims liability for incidental, spe-
cial, or consequential damages resulting from the use or un-
availability of this product. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or con-
sequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. THIS WARRANTY SUPERSEDES ALL WARRANTIES THAT ARE INCLUDED WITH THIS PRODUCT 5 V BIAS SLEEVE RING TIP 1 MEG OHM 5 V BIAS SLEEVE RING TIP 1 MEG OHM PREAMP PREAMP Certifications P2T: Certified to FCC Part 74 (FCC ID No. DD4P2T). Certified in Can-
ada by IC to RSS123 and RSS102 (Certification No. 616AP2T). This class B digital apparatus complies with Canadian ICES003. EP2T/UKP2T: Meets essential requirements of European R&TTE Di-
rective 99/5/EC, eligible to bear the CE mark:
. Type ap-
proved to EN 300 422 Parts 1 and 2. Meets requirements of EMC Stan-
dard EN 301 489 Parts 1 and 9. P2R: Approved under the Declaration of Conformity (DoC) provision of FCC Part 15. Certified in Canada by IC to RSS-123 (Certification No. 616AP2R). This class B digital apparatus complies with Canadian ICES003. Meets essential requirements of European Union R&TTE Directive 99/5/EC, eligible to bear mark. Meets requirements of EMC standards EN 300 422 Parts 1 and 2 and EN 301 489 Parts 1 and 9. O682 LIMITED ONE-YEAR WARRANTY Shure Incorporated (Shure) hereby warrants that this product will be free from defects in materials and workmanship for a pe-
riod of one year from the date of purchase for all cartridge and housing assembly parts and for a period of one year from the date of purchase for all transmitter parts. At its option Shure will repair or replace the defective product and promptly return it to you, or refund the purchase price. You should retain proof of purchase to validate the purchase date and return it with any warranty claim. If you believe this product is defective within the warranty peri-
od, carefully repack the unit, insure it, and return it postage pre-
paid to:
Shure Incorporated Attention: Service Department 222 Hartrey Avenue Evanston, Illinois 60202-3696 U.S.A. APPENDIX P2R Receiver MIX IN Jack Wiring Diagrams Mono Line Input The MIXIN jack accepts line-level signals, such as click tracks, effects processors, pre-amp out-
puts from guitar or bass amps, or line outputs from mixing consoles. When used with a mono connec-
tor, the ring of the MIX IN jack is grounded. This doesnt harm the P2R. Condensor Mic TRS Input By connecting a condensor microphone to the MIX IN jack, you can include sounds from your immedi-
ate surroundings in your personal mix. When the MIX IN Jack is used with a TRS connector, such as the Shure AP200 adaptor, the P2R supplies a 5 volt bias on the ring signal. This enables the MIX IN jack to power a condensor microphone. The AP200 works with any Shure microphone that has a mini 4-pin connector. 14 SHURE Incorporated Web Address: http://www.shure.com SHURE Incorporated Web Address: http://www.shure.com 222 Hartrey Avenue, Evanston, IL 60202-3696, U.S.A. 222 Hartrey Avenue, Evanston, IL 60202-3696, U.S.A. Phone: 847-866-2200 Fax: 847-866-2279 Phone: 847-866-2200 Fax: 847-866-2279 In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055 In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055 Elsewhere, Phone: 847-866-2200 Fax: 847-866-2585 Elsewhere, Phone: 847-866-2200 Fax: 847-866-2585
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2002-04-17 | 614 ~ 784 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2002-04-17
|
||||
1 | Applicant's complete, legal business name |
Shure Incorporated
|
||||
1 | FCC Registration Number (FRN) |
0012570552
|
||||
1 | Physical Address |
5800 W. Touhy Ave
|
||||
1 |
Niles, Illinois 60714-4608
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
DD4
|
||||
1 | Equipment Product Code |
P2T
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
C**** K****
|
||||
1 | Title |
EMC Project Engineer
|
||||
1 | Telephone Number |
847-6********
|
||||
1 | Fax Number |
847-6********
|
||||
1 |
k******@shure.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Personal Monitor Transmitter | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output is conducted. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
LS Research, LLC
|
||||
1 | Name |
R******** U******
|
||||
1 | Telephone Number |
262-3********
|
||||
1 | Fax Number |
262-3********
|
||||
1 |
r******@lsr.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 74 | 518 | 608 | 0.03 | 0.005 % | 120KF3E | ||||||||||||||||||||||||||||||||||
1 | 2 | 74 | 614 | 784 | 0.03 | 0.005 % | 120KF3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC