FCC ID: 2ALU7-4270008 Marine Class B AIS Transceiver with WLAN

SAS-600 AIS Class B transceiver Installation and operation manual Thank you for purchasing this AIS Class B transceiver. This product has been engineered to offer you the highest level of performance and durability and we hope that it will provide many years of reliable service. We constantly strive to achieve the highest possible quality standards, should you encounter any problems with this product, please contact your dealer who will be pleased to offer any assistance you require. List of abbreviations List of abbreviations AIS AIS SART AP AtoN CD CE COG COM CPA CS DC Dec DGPS DGNSS DHCP DOP DSC DTM ECDIS ENI EPFS EPIRB ERI Automatic Identification System AIS Search and Rescue Transmitter Access Point (Relating to WiFi behaviour) AIS Aid to Navigation Compact Disc European Declaration of Conformity Course Over Ground Common (electrical) Closest Point of Approach Carrier Sense Direct Current Decimal Differential GPS Differential GNSS Dynamic Host Configuration Protocol Dilution of Precision Digital Selective Calling Datum Electronic Chart Display and Information System Unique European Vessel Identification Number Electronic Position Fixing System Emergency Position Indicating Radio Beacon Electronic Reporting International Page 1 List of abbreviations Estimated Time of Arrival External Federal Communications Committee GNSS satellite fault detection message GNSS fix accuracy and integrity message Global positioning system (GPS) fix data message Geographic position - Latitude/longitude message Globalnaya Navigazionnaya Sputnikovaya Sistema (Russian GNSS) Electrical Ground GNSS fix data message Global Navigation Satellite System Global Positioning System GNSS range residuals message GNSS DOP and active satellites message GNSS satellites in view message Heading true message Hexadecimal International Electrotechnical Commission International Maritime Organisation Internal Ingress Protection (to powerful water jets) Ingress Protection (1m immersion for 30 minutes) International Standards Organisation Knots ETA EXT FCC GBS GFA GGA GLL GLONASS GND GNS GNSS GPS GRS GSA GSV HDT Hex IEC IMO INT IPx6 IPx7 ISO Kt Page 2 List of abbreviations LAT LCD LON LR MKD MMSI MOB NC NAV NM NMEA PDF PGN PI RAIM RED RF RMC ROT RX SD SOG SOLAS SRM TCP Latitude Liquid Crystal Display Longitude Long Range Minimum Keyboard and Display Maritime Mobile Service Identity Man Overboard Normally Closed (electrical) Navigation Nautical Miles National Marine Electronics Association Portable Document Format Parameter Group Number Presentation Interface Receiver Autonomous Integrity Monitoring Radio Equipment Directive Radio Frequency Recommended minimum specific GNSS data message Rate of Turn Receive Secure Digital Speed Over Ground Safety of Life at Sea Safety Related Message Transmission Control Protocol Page 3 List of abbreviations Time to Closest Point of Approach Time Division Multiple Access True heading and status message Threaded NeillConcelman (a type of connector) Threads per Inch Transmit User Datagram Protocol Ultra High Frequency Co-ordinated Universal Time Dual ground/water speed message All VDL AIS messages received AIS own-ship broadcast data Very High Frequency Voltage Standing Wave Ratio Course over ground and ground speed message World Geodetic System 1984 Waste Electrical & Electronic Equipment Wireless networking technology TCPA TDMA THS TNC TPI TX UDP UHF UTC VBW VDM VDO VHF VSWR VTG WGS84 WEEE WiFi Page 4 Table of contents Table of contents 1 Notices ............................................................ 9 1.1 Safety warnings ............................................................................. 9 1.2 General notices.............................................................................. 10 Regulatory statements................................................................... 11 1.3 Introduction .................................................... 15 2 2.1 About AIS....................................................................................... 15 3 Installation and configuration....................... 17 3.1 Whats in the box? ......................................................................... 17 3.2 Preparing for installation ................................................................ 17 Installation procedures................................................................... 18 3.3 3.4 Connecting the equipment............................................................. 27 3.5 Grounding the AIS transceiver....................................................... 36 Connection to an NMEA2000 network (optional)........................... 37 3.6 USB Connection ............................................................................ 37 3.7 3.8 Turning the AIS transceiver on ...................................................... 37 3.9 Passwords and security................................................................. 38 4 Operation ........................................................ 39 4.1 Using the AIS transceiver .............................................................. 39 Display and controls....................................................................... 40 4.2 Button functions ............................................................................. 40 4.3 4.4 Adjusting display brightness .......................................................... 41 4.5 Menu navigation............................................................................. 42 Information displayed..................................................................... 44 4.6 Configuring vessel information....................................................... 50 4.7 4.8 Confirming correct operation.......................................................... 52 Displaying AIS targets.................................................................... 53 4.9 Page 5 Table of contents 4.10 Micro SD card data input................................................................ 55 4.11 WiFi Feature................................................................................... 57 5 Technical information.................................... 59 5.1 AIS Transceiver overall dimensions............................................... 59 5.2 GNSS Antenna drawing................................................................. 60 NMEA 2000 PGN List .................................................................... 61 5.3 5.4 Troubleshooting ............................................................................. 63 6 Technical specification ................................. 67 Applicable equipment standards.................................................... 67 6.1 6.2 Product category............................................................................ 68 Physical.......................................................................................... 68 6.3 Environmental ................................................................................ 69 6.4 Electrical......................................................................................... 69 6.5 6.6 Display and user interface.............................................................. 69 Internal GNSS................................................................................ 70 6.7 TDMA Transmitter.......................................................................... 70 6.8 6.9 TDMA Receiver.............................................................................. 70 6.10 DSC Receiver ................................................................................ 71 6.11 RF Connections ............................................................................. 71 6.12 WiFi................................................................................................ 72 6.13 Data interface................................................................................. 72 6.14 Power and data connector information .......................................... 73 6.15 Open source licences..................................................................... 73 Page 6 List of figures and tables List of figures and tables Figure 1 The AIS network .................................................................. 15 Figure 2 Whats in the box? ............................................................... 17 Figure 3 Typical AIS transceiver connection...................................... 19 Mounting the AIS transceiver............................................... 21 Figure 4 Desk mounting the AIS transceiver ..................................... 22 Figure 5 Panel mounting the AIS transceiver .................................... 23 Figure 6 Figure 7 GNSS Antenna location....................................................... 24 GNSS Antenna connection.................................................. 25 Figure 8 Figure 9 VHF Antenna location.......................................................... 26 Figure 10 VHF Antenna connection..................................................... 27 Table 1 Accessory cable................................................................... 28 Figure 11 Using the accessory cable................................................... 29 Figure 12 Serial input port connection ................................................. 30 14 Way connector cable wiring connections........................ 31 Figure 13 Table 2 14 Way connector serial data ports ..................................... 31 Figure 14 Serial bi-directional port connection..................................... 32 18 Way connector cable wiring connections........................ 33 Figure 15 18 Way connector serial data ports ..................................... 33 Table 3 Table 4 Alarm relay connections ...................................................... 34 Figure 16 Power connection ................................................................ 35 Table 5 Power supply connections................................................... 35 Figure 17 Grounding the AIS transceiver............................................. 36 Figure 18 Enter password screen........................................................ 38 Figure 19 AIS Transceiver front panel ................................................. 40 Figure 20 Home page menu screen .................................................... 42 Figure 21 Main menu structure............................................................ 43 Figure 22 Display layout ...................................................................... 44 Figure 23 GNSS Icons......................................................................... 45 Figure 24 Alarm icons.......................................................................... 46 Table 6 Alarms list ............................................................................ 48 Figure 25 Vessel dimension measurement.......................................... 52 Figure 26 Target list screen ................................................................. 53 Figure 27 AIS target symbols displayed .............................................. 54 Figure 28 Micro SD card Socket.......................................................... 56 Page 7 List of figures and tables Figure 29 AIS Transceiver dimensions ................................................59 Figure 30 GNSS Antenna ....................................................................60 PGN Lists.............................................................................62 Table 7 Table 8 Troubleshooting ...................................................................65 Page 8 Notices 1 Notices

!

When reading this manual please pay particular attention to warnings marked with the warning triangle symbol shown on the left. These are important messages for safety, installation and usage of the AIS transceiver. 1.1 Safety warnings

!

!

!

!

!

This equipment must be installed in accordance with the instructions provided in this manual. Failure to do so may seriously affect its performance and reliability. It is strongly recommended that a trained technician installs and configures this product. This product must be connected to protective ground via the ground connection point. It is essential that the ground connection point is used in all installations, regardless of what other equipment is connected. The ground connection point must be bonded to protective ground using as short a connection as possible. This equipment is intended as an aid to navigation and is not a replacement for proper navigational judgement. Information provided by the equipment must not be relied upon as accurate. User decisions based upon information provided by the equipment are done so entirely at the users own risk. Do not install this equipment in a flammable atmosphere such as in an engine room or near to fuel tanks. It is recommended that this product is not installed in direct sunlight or under a windshield where it may be subject to excessive solar heating. Page 9 Notices

!

!

Do not attempt to service this equipment as doing so may cause fire, electric shock or malfunction and will invalidate the warranty. If any malfunctions are detected contact your supplier or service agent. NOT ALL SHIPS CARRY AIS. The Officer of the Watch should always be aware that other ships and, in particular, leisure craft, fishing vessels and warships may not be fitted with AIS. Any AIS equipment fitted on other ships as a mandatory requirement may also be switched off based on the Masters professional judgement. 1.2 General notices 1.2.1 Position source All marine AIS transceivers utilise a satellite based location system such as the GLONASS or GPS.

!

The accuracy of a GNSS position fix is variable and affected by factors such as the antenna positioning, how many satellites are used to determine a position and for how long satellite information has been received. 1.2.2 Compass safe distance The compass safe distance of this AIS transceiver is 0.5m or greater for a 0.3 deviation. 1.2.3 Safe operating distance The safe operating distance of this AIS transceiver is 20cm from the antenna. 1.2.4 Product category This product is categorized as protected in accordance with the definitions provided in IEC 60945. 1.2.5 Disposal of AIS transceiver and packaging Please dispose of this AIS transceiver in accordance with the European WEEE Directive or with the applicable local regulations for disposal of Page 10 Notices electrical equipment. Please dispose of the packaging in an environmentally friendly manner. 1.2.6 Accuracy of this manual This manual is intended as a guide to the installation, setup and use of this product. If you are in any doubt about any aspect of this product, please contact your dealer. 1.3 Regulatory statements 1.3.1 Declaration of Conformity The manufacturer of this product declares that this product is in compliance with the Radio Equipment Directive (2014/53/EU) and as such, displays the CE mark. The RED declaration of conformity is provided as part of the documentation pack. Page 11 Notices 1.3.2 FCC Notice

!

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Page 12 Notices 1.3.3

!

Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1.This device may not cause interference, and 2.This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1. L'appareil ne doit pas produire de brouillage, et 2. L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le Fonctionnement. Cet appareil numrique de la classe B est conforme la norme NMB-

003 du Canada. Page 13 Notices Page 14 Introduction 2 Introduction 2.1 About AIS The marine Automatic Identification System (AIS) is a location and vessel information reporting system. It allows vessels equipped with AIS to automatically and dynamically share and regularly update their position, speed, course and other information such as vessel identity with similarly equipped vessels. Position is derived from GLONASS or GPS and communication between vessels is by VHF digital transmissions. Figure 1 The AIS network Page 15 Introduction Page 16 Installation and configuration 3 Installation and configuration 3.1 Whats in the box?

Please ensure all items are present and if any of the items are missing please contact your dealer. AIS transceiver Product CD Mounting bracket Fixings Warranty card Product mounting template Quick start guide Power cable Data accessory cable GNSS Antenna Cable Assy Figure 2 Whats in the box?

3.2 Preparing for installation In addition to the items provided with the AIS transceiver the following items will be required to complete the installation:

Page 17 Installation and configuration 3.2.1 VHF Antenna Connection of a suitable VHF antenna will be required for the AIS transceiver to operate. The antenna cable should be terminated with a PL-259 (or UHF) connector. A surge arrestor should be fitted in line with VHF antenna connector. See section 3.3.3 for more information. Please take note of the warnings listed at the start of this manual regarding the installation and use of antennas. 3.2.2 Antenna cables The supplied GNSS antenna is provided with 10 metres (32.8ft) of cable. If this is not sufficient to reach between the desired GNSS antenna location and the AIS transceiver you will require an extension cable. Please contact your dealer for details. 3.2.3 GNSS Antenna mount A mounting bracket is required for the supplied GNSS antenna. 3.2.4 Data interface cables Suitable screened, multi core cable will be required to connect the ships sensor (DGPS, Gyro etc.) data ports to the AIS transceiver. 3.3 Installation procedures Before beginning installation of your AIS transceiver, please ensure that you read all of the instructions in this manual. The following sections explain the installation process step by step for each of the main system elements. A typical system and connection diagram is provided in Figure 3. For more complicated installations you may wish to order the optional USB Cable, 14 or 18 way data cables, or AIS Junction Box. Page 18 Installation and configuration GNSS antenna VHF antenna Surge arrestor Chassis/GND 12V DC to 24V DC Supply Optional connections NMEA2000 Ships sensor data Displays etc. Figure 3 Typical AIS transceiver connection Page 19 Installation and configuration 3.3.1 Step 1 - Installing the AIS transceiver Please note the following guidelines when selecting a location for your AIS transceiver:

The AIS transceiver must be fitted in a location where it is at least 0.5m (1ft 8ins) from a compass or any magnetic device. There should be adequate space around the AIS transceiver for routing of cables. See Figure 29. for details of the AIS transceiver dimensions. The ambient temperature around the AIS transceiver should be maintained between -15C and +55C (5F to 131F). Ensure adequate ventilation is present when panel mounting the AIS transceiver. It is recommended that the AIS transceiver be installed in a 'below decks' environment protected from the weather. The AIS transceiver is supplied with four self tapping screws for attachment of the AIS transceiver to a suitable surface using the supplied bracket. Please refer to Figure 5. for guidance. The AIS transceiver can be panel mounted using the four self tapping screws provided. Please refer to Figure 6. for guidance. Access behind the panel is required when using this mounting option. The AIS transceiver should be mounted in a location where the display is visible to the user at the position from which the vessel is normally operated. Page 20 Installation and configuration Panel mounted Desk mounted Overhead mounted

(reverse mounting bracket) Figure 4 Mounting the AIS transceiver Refer to Figure 29. for dimensions. A drilling and cutting template is provided with the AIS transceiver. To panel mount the unit it is necessary to remove the 4 off socket cap screws recessed in front of the unit. See Figure 6. Page 21 Installation and configuration Figure 5 Desk mounting the AIS transceiver Page 22 Installation and configuration Figure 6 Panel mounting the AIS transceiver Installing the GNSS antenna 3.3.2 For mounting the GNSS antenna supplied with your AIS transceiver you will require a one inch 14 TPI pole mount. Contact your dealer to source a mount suitable for the installation location. Please note the following guidelines when selecting a location for the GNSS antenna:

The GNSS antenna mount should be secured to a rigid surface. Page 23 Installation and configuration The GNSS antenna should be located where it has a clear, unobstructed view of the sky overhead. The GNSS antenna should be mounted as high as possible, however it is not recommended to mount the antenna on the top of a high mast where the motion of the vessel will cause the antenna to move and potentially reduce the accuracy of the GNSS position. Route the GNSS antenna cable to the AIS transceiver. If extension cables are required all junctions should be made using appropriate co-axial connectors and made watertight. Connect the GNSS antenna cable to the GNSS connector on the AIS transceiver. GNSS Antenna should be at least 5m (16ft) from radar or satellite communication antennas. It should also be away from the radar beam path and mounted on a rigid surface. Radar beam path 5m (16ft) GNSS Antenna Figure 7 GNSS Antenna location Page 24 Installation and configuration GNSS Antenna connection Figure 8 GNSS Antenna connection Installing the VHF antenna 3.3.3 Please note the following guidelines when selecting and locating the AIS VHF antenna:

The VHF antenna should be located as high as possible and positioned as far from other antennas as possible. The VHF antenna should have omnidirectional vertical polarization. Where possible the VHF antenna should be installed at least 3m

(10ft) away from other transmitting radio, satellite and radar antennas. Ideally the AIS VHF antenna should be mounted directly above or below the ships primary VHF radiotelephone antenna, with no horizontal separation and with a minimum of 2m vertical separation. Refer to Figure 9. for further guidance. Page 25 Installation and configuration The VHF antenna cable should be kept as short as possible to minimize signal loss. High quality, low loss co-axial cable appropriate to the installation location should be used. The VHF antenna cable should be terminated in a PL-259 co-axial connector for connection to the AIS transceiver. Any outdoor installed connectors in the antenna cables should be waterproof by design. Antenna cables should be installed in separate signal cable channels at least 10cm (4ins) away from power supply cables. Crossing of cables should be done at right angles and sharp bends in the antenna cables should be avoided. It is recommended that a suitable surge arrestor is fitted in-line with the VHF antenna connector. Connect the VHF antenna cable to the VHF connector on the AIS transceiver as shown in Figure 10. VHF Antenna should be at least 3m (10ft) from other transmitting radio, satellite and radar antennas. 3m (10ft) VHF Antenna Figure 9 VHF Antenna location Page 26 Installation and configuration VHF antenna connection Figure 10 VHF Antenna connection 3.4 Connecting the equipment 3.4.1 Data connections The accessory cable provides a simple method of implementing a typical Class B installation with minimum difficulty. If the planned installation is more complex it is recommended to use the optional fully wired cables and Junction box for greater flexibility An accessory cable is supplied with the product to provide connections to the NMEA0183 bi-directional data ports. The cable has a pre-moulded connector at one end which should be connected to the 18-way connector on the rear of the unit. The other end of the cable has colour coded wires ready for connection The table in Table 1 lists the function of each colour coded wire for reference. Page 27 Installation and configuration Decription Port Name in MKD Wire Colour Pin Function NMEA0183 Port 1 COM NMEA0183 Port 1 Black NMEA0183 Port 1 TX B NMEA0183 Port 1 NMEA0183 Port 1 TX A NMEA0183 Port 1 NMEA0183 Port 2 RX B NMEA0183 Port 2 NMEA0183 Port 2 RX A NMEA0183 Port 2 NMEA0183 Port 2 COM NMEA0183 Port 2 1 3 4 6 Blue/White White/Blue Red/White Orange/White 10 Black 11 High speed NMEA0183 output

(38,400baud) intended for chart plotters Can be set to low speed (4,800 baud) intended for connec-

tion to other NMEA0183 compati-

ble sensors for multi-

plexing of data to the chart plotter Table 1 Accessory cable The Accessory Cable provides independent connection to the transmit side of one NMEA0183 port and to the receive side of another NMEA0183 port. This permits independent setting of transmit and receive baud rates, enabling flexible connection to two external pieces of NMEA equipment. Page 28 Installation and configuration Without acessory cable AIS transceiver Chart plotter OR Gyro-compass Chart plotter Using accessory cable AIS transceiver Gyro-compass Chart plotter Figure 11 Using the accessory cable A multiplexing feature is provided, which means any messages which are received via the NMEA 2 port are automatically re-transmitted via the NMEA 1 port. Thus two independent NMEA data streams, AIS and external data are merged into one. This is particularly useful when using a chart plotter having only a single NMEA0183 port, for example: An additional sensor such as a gyro-compass can be connected to the AIS transceiver via the input port and the AIS transceiver can be connected via the output port to the chart plotter resulting in the chart plotter receiving both AIS information and heading information simultaneously. Page 29 Installation and configuration It is important to ensure that the equipment is configured to use the matching baud rates. 3.4.2 Sensor configuration For more complex installations the AIS transceiver has six NMEA0183

(IEC61162-1/2) data ports for connection of ships sensors and display equipment as described in Table 2. and Table 3. There are three input only ports for ships sensor data and three bi-directional high speed ports for connection of display equipment. These can be connected using an accessory cable pack purchased through your dealer. 3.4.3 Data input ports (14 way connector) 14 way interface connection Figure 12 Serial input port connection Page 30 Installation and configuration 14 13 12 11 10 9 5 8 2 4 7 1 6 3 SIGNAL NOT USED NOT USED SILENT N SILENT P NMEA RX4 B NMEA RX4 A NMEA RX4 COM NMEA RX5 B NMEA RX5 A NMEA RX5 COM NMEA RX6 B NMEA RX6 A NMEA RX6 COM CHASSIS WIRE COLOUR BLACK BROWN BLUE RED ORANGE PURPLE GREEN WHITE WHITE / BLACK GREY YELLOW RED / BLACK PINK DRAIN WIRE PIN 1 3 6 7 2 5 8 9 12 11 14 13 10 4 Figure 13 14 Way connector cable wiring connections Data port Function Type 4 5 6 NMEA 0183 Input 4 Receive only NMEA 0183 Input 5 Receive only NMEA 0183 Input 5 Receive only Table 2 14 Way connector serial data ports Default baud rate 4800 4800 4800 Page 31 Installation and configuration Note: Any unused ports should be terminated by a 120 Ohm resistor across RX A and RX B signals. 3.4.4 Silent mode switch To activate the Silent mode switch, apply a voltage of between 2V and 30V to the SILENT P (Pin 7) and SILENT N (Pin 6) terminals of the 14 way connector. You will need to order an accessory cable for this. 3.4.5 Data bi-directional ports (18 way connector) 18 way interface connection Figure 14 Serial bi-directional port connection Page 32 Installation and configuration 18 17 16 15 14 13 12 11 10 9 6 5 4 2 7 3 8 1 SIGNAL NMEA TX1 B NMEA TX1 A NMEA RX1 B NMEA RX1 A NMEA 1 COM NMEA TX2 B NMEA TX2 A NMEA RX2 B NMEA RX2 A NMEA 2 COM ALM NC ALM COM NMEA TX3 B NMEA TX3 A NMEA RX3 B NMEA RX3 A NMEA 3 COM CHASSIS WIRE COLOUR ORANGE BROWN PURPLE BLUE BLACK RED RED / WHITE PINK YELLOW GREEN GREY WHITE ORANGE / WHITE BLACK / WHITE BROWN / WHITE YELLOW / WHITE GREEN / WHITE DRAIN WIRE PIN 3 4 7 8 1 2 5 6 10 11 16 12 13 17 14 18 15 9 Figure 15 18 Way connector cable wiring connections Data port Function Type 1 2 3 NMEA 0183 Port 1 NMEA 0183 Port 2 NMEA 0183 Port 3 Bi-directional Bi-directional Bi-directional Table 3 18 Way connector serial data ports Default Baud rate 38400 38400 38400 Page 33 Installation and configuration Note: Any unused ports should be terminated by a 120 Ohm resistor across RX A and RX B signals. COMMON signals should be grounded. All sensor ports can be configured via the Interface settings menu which can be found under the Home > System settings > Interfaces menu option. 3.4.6 Alarm connections The AIS transceiver also provides connections to the alarm relay contacts. The alarm relay connections are described in Table 4. These should be connected using an optional accessory cable or Junction Box. Alarm connection Function Contact rating COM NC Alarm relay common connection Alarm relay normally closed connection 2A at 220VDC or 60W maximum Table 4 Alarm relay connections Page 34 Installation and configuration 3.4.7 Power connection Power is connected to the AIS transceiver via the supplied 2 way power cable as shown in Figure 16. Power connection Figure 16 Power connection Wire colour Function Connect to Red Black Power supply +

12VDC to 24VDC power supply Power supply -

Power supply ground Table 5 Power supply connections The power supply current ratings and recommended fusing or circuit breaker currents are as follows:

Page 35 Installation and configuration A 12VDC supply should be able to provide a peak current of 4.0A and be fused at 6.3A. A 24VDC supply should be able to provide a peak current of 3.0A and should be fused at 5.0A. 3.5 Grounding the AIS transceiver An M4 grounding screw and ring crimp are provided in the fixing kit to allow connection to the grounding point on the rear of the AIS transceiver chassis as indicated in Figure 17. Ground screw and ring crimp Figure 17 Grounding the AIS transceiver

!

This product must be connected to protective ground via the ground connection point. It is essential that the ground connection point is used in all installations, regardless of what other equipment is connected. The ground connection point must be bonded to protective ground using as short a connection as possible. Page 36 Installation and configuration 3.6 Connection to an NMEA2000 network (optional) The AIS transceiver can be connected to an NMEA2000 network by a suitable NMEA2000 network cable available from your local dealer. If your vessel has an NMEA2000 network please refer to the relevant documentation for your NMEA2000 equipment. Once connected, and with your chart plotter also connected you will be able to receive AIS targets on your chart plotter. A list of supported PGNs is provided at the rear of this document. 3.7 USB Connection An optional USB cable is available for connection to a PC or Mac. The USB connector can be connected directly to the USB port on the PC or Mac via the optional USB cable. To enable connection of the AIS transceiver to a PC the USB drivers, supplied on the product CD, must first be installed. Driver installation is typically not required for use with a Mac. To install the drivers please follow the steps below:

1. Insert the CD into the PC and navigate to the USB drivers folder. 2. Double click on the setup.exe file to launch the installer. 3. Follow the on screen installation instructions to complete installation. 4. Once installed the AIS unit can be connected to the PC. The USB drivers will be installed automatically and the AIS will appear as a new COM port device. 5. Select the AIS COM port and a baud rate of 38,400 in PC based navigation software to make use of the AIS data.

!

If the USB connection is removed from the PC or Mac during use you must reset the connection before further use. To reset the connection, disconnect then reapply power to the AIS before closing and relaunching any PC or Mac applications using the USB connection. Finally, reconnect the USB cable between the PC or Mac and the AIS transceiver 3.8 Turning the AIS transceiver on The AIS transceiver does not have an On / Off switch and will operate immediately that power is applied to the unit. Page 37 Installation and configuration 3.9 Passwords and security The WiFi feature in this AIS transceiver may require a password to be entered. In order to do this, you will be prompted by a password entry screen. The password entry screen is shown in Figure 18. Highlight the required character, then press Select to enter that character. When all characters of the password have been entered, select OK. 16:58:29 SOG 21.1kt COG 88.0 UTC + 1h PASSWORD SETTINGS Enter the current password:

50 32.0286 N 0 55.2715 W 5W

!

1 Q

!?

2 W 3 E 4 5 R T A Z S X D C F V 6 G B 7 8 Y U 9 I 0 O

. P H N J M K L OK Figure 18 Enter password screen Page 38 Operation 4 Operation Please read the warning notices at the front of this manual before operating the AIS transceiver. 4.1 Using the AIS transceiver Once the unit has been configured it is ready for use. Providing other vessels with AIS transceivers installed are within radio range of your vessel you should see their details appear on your target list. These vessels will also be able to see your vessel on their chart plotter or PC. It may take up to six minutes for your full vessel details to be visible to others. Specific details of how to configure your chart plotter to make use of the AIS transceiver features will be given in your chart plotter manual. If you are using charting software running on a PC, please refer to the instructions provided with your chart plotting software for details of how to configure it to display AIS information. Page 39 Operation 4.2 Display and controls Chart /

Screen brightness Select Display Micro SD card slot behind door Options menu Back / Home Function keys

(up, down, left right) Scroll wheel

(push to select) Figure 19 AIS Transceiver front panel The front panel of the AIS transceiver is shown in Figure 19. with each control marked. 4.3 Button functions Scroll wheel. This is used to highlight information presented on the display. The scroll wheel can also be pressed to confirm data entry or select information. Chart / Screen brightness key. When pressed with a short press will go to the Chart screen. When pressed and held it will go to the Display brightness screen. Page 40 Operation Options menu key. Provides access to additional features and relevant shortcuts on certain screens. Back / Home key. When pressed with a short press cancels the current operation and moves to the previous menu or if pressed and held will return to the home screen. Select key. When pressed selects the current option highlighted on the screen. Up, down, left and right function keys. Provide an alternative means of navigating around the screen. Speaker. The speaker is located behind the Scroll wheel and can provide an audible sound when a key is pressed, a message is received, or an alarm is activated. Sounds can be enabled or disabled via the Sound Settings menu. Micro SD card. The Micro SD card socket (behind the door) is provided to allow uploading of new software to the AIS transceiver. Display. The display shows essential AIS operating information and allows for configuration of the AIS transceiver via the menus. 4.4 Adjusting display brightness Press and hold the Chart / Screen brightness key. The screen will change to the Display Settings screen. Page 41 Operation 4.5 Menu navigation 16:58:29 SOG 21.1kt COG 88.0 UTC + 1h HOME 50 32.0286 N 0 55.2715 W 5W

!

Target list User settings Target plot Chart

!

Messages Alarms Own dynamic data System settings Figure 20 Home page menu screen 4.5.1 Main / Sub menus Menus are displayed as a set of icons which can be navigated by using the controls. Selection of an icon will then display the information beneath in accordance with Figure 21. Pressing the Back / Home key will exit the menu. Page 42 Operation HOME TARGET LIST USER SETTINGS TARGET PLOT CHART MESSAGES ALARMS OWN DYNAMIC DATA SYSTEM SETTINGS DISPLAY SETTINGS SOUND SETTINGS LANGUAGE TIME FILTER & CPA/TCPA SETTINGS MESSAGE INBOX SENT MESSAGES COMPOSE MESSAGE LOGGING INTERFACES SYSTEM INFORMATION ADVANCED GNSS SOURCE CHART SETUP HELP AND SUPPORT VESSEL DATA SETTINGS SENSOR PORT 1 SENSOR PORT 2 SENSOR PORT 3 WiFi GNSS OUTPUT NMEA0183 PORT 1 NMEA0183 PORT 2 NMEA0183 PORT 3 NMEA 2000 PORT DATA VIEW AIS SART TEST RADIO & LONG RANGE SETTINGS SOFTWARE UPDATES SAVE / RESTORE SETTINGS Figure 21 Main menu structure 4.5.2 Data entry screens Some screens allow you to enter data, such as vessel parameters. On these screens you navigate to the desired field and select the appropriate menu item. Pressing the Back / Home key will exit these menus. 4.5.3 Keyboard / Keypad screens Some screens require text or numeric entry. When these are selected, a virtual keyboard is displayed which can be used to enter text or numbers. Page 43 Operation Options menu 4.5.4 On certain screens, the Options Menu will bring up a further list of functions specific to that screen. This is indicated by this icon. 4.6 Information displayed Position Speed / Course Time Time offset RX TX Filtering Power setting GNSS Status Alarms 16:58:29 SOG 21.1kt COG 88.0 UTC + 1h HOME 50 32.0286 N 0 55.2715 W 5W

!

Menu title Messages Main display area Figure 22 Display layout 4.6.1 Menu title Refers to the current menu displayed from Figure 21. 4.6.2 Time Time derived from GNSS satellites or AIS Base Stations. 4.6.3 Time offset Offset from UTC, set on the Time menu. Page 44 Operation 4.6.4 Speed / Course Vessel speed and course as taken from GNSS satellite data. 4.6.5 Position Vessel position taken from GNSS source. 4.6.6 Icons RX - Illuminates to show receiving an AIS message. TX - Illuminates to show transmission of an AIS message. Filtering - Illuminated to show that target filter settings apply. Alarms - Displays an alarm icon to show the presence of acknowledged or unacknowledged AIS alarms. Messages - Displays an envelope icon with a number to show the pres-

ence of AIS messages received See menu Messages. GNSS Status - Displays an icon to show if GNSS data is being received. GNSS Available GNSS Unavailable Figure 23 GNSS Icons Power - Displays 1W or 5W to indicate the current radio power output. Page 45 Operation 4.6.7 Alarms The AIS transceiver performs self checking functions continuously. If a self check fails a display will appear on the screen notifying the operator of this. This will be accompanied by a sound. The alarm can be acknowledged via an on-screen message. The list of currently active AIS Alarms can be displayed by accessing the Alarms menu. Certain AIS Alarms can be switched off in the Alarm Settings menu. This is available from the Options menu. The alarm conditions are displayed at the top of the screen and are represented as follows:

New unacknowledged alarm, this will flash.

!

New acknowledged alarm. No active alarms. Figure 24 Alarm icons If any alarm condition persists, contact your dealer or installer. Page 46 Operation Possible alarm conditions are listed Table 6. Alarm TX Malfunction Description This alarm will occur if the MMSI has not been configured. This alarm can also occur if the radio hardware has failed to select the correct frequency, that the output power is too low or a transmitter shutdown has occurred. In this situation, ALR 001 is output. The alarm will be cleared if the transmitter recovers normal operation. RX Channel x malfunction This alarm occurs should the receiver hardware malfunction. The receiver is identified by the value of x (as shown below). The following alarms will be generated in this condition:

ALR 003 - Rx Channel 1 ALR 004 - Rx Channel 2 ALR 005 - DSC (Channel 70) If the receiver returns to normal operation this alarm will be cleared. Antenna VSWR exceeds limit This alarm occurs if there is a problem with your antenna or antenna connection. No valid COG information No valid SOG information This alarm occurs if the AIS transceiver has no valid Course Over Ground information from any connected sensor. This alarm occurs if the AIS transceiver has no valid Speed Over Ground information from any connected sensor. Page 47 Operation Alarm Description Heading lost or invalid No sensor position in use UTC Sync Invalid Heading sensor offset This alarm occurs if the AIS transceiver has no valid heading information from any connected sensor, or if the heading is undefined. This alarm occurs if the AIS transceiver has no valid position information from any connected sensor. This alarm indicates that the transmitter is no longer directly synchronized with the GNSS receiver. This may be because the GNSS receiver cannot receive sufficient satellites. This alarm occurs if the difference between the course over ground and heading data is greater than 45 for more than 5 minutes. This alarm only occurs if the vessel speed over ground is greater than 5 knots. Table 6 Alarms list 4.6.8 Messages Messages can be received from other AIS equipped vessels and also sent to specific vessels (addressed messages) or sent to all vessels in range

(broadcast messages). Reception of an AIS text message is indicated by the presence of the message icon at the top of the screen. This icon is shown whenever there are unread AIS text messages. Messages can be reviewed and replied to via the Inbox. The AIS transceiver can store up to a maximum of 20 messages in the Inbox and 20 messages in the Sent folder. If the number of messages exceeds 20 then the oldest message will be overwritten. When a Safety Related Message is received the user will be notified immediately with a pop-up showing the message. Standard text messages are Page 48 Operation not displayed on receipt, however the message icon will be displayed at the top of the screen. AIS messages can be viewed, created and transmitted from the Messages menu. The available options are:

Compose - takes you to the message composition screen Inbox - takes you to the received message list view Sent - shows a list of recently sent messages. To compose a new message, select the type of message from the drop down menu and the destination. This can be by directly entering the MMSI, or by selecting from a list of visible targets. The message text is entered using the on screen keyboard. Messages are limited to 80 characters in length.

!

Class B AIS transceivers are permitted to receive broadcast SRMs and broadcast text messages, however this function is not mandatory. Some Class B AIS transceivers are not able to receive addressed SRM or text messages. There is therefore no guarantee that text messages or SRMs sent by this device to a Class B AIS transceiver will be received. 4.6.9 Chart The AIS transceiver contains an application which will display AIS targets received, along with its own vessel position on a chart style plot. The chart can be scrolled up, down, left, and right using the Function keys. Zooming in and out is via the Scroll wheel. Targets can be selected by moving the cross hairs over a target and pressing the Select key. The Options menu is also available for more advanced features. Within the Options menu, the chart can be oriented to either North, Heading, or Course Up. The chart can be set so that the own vessel position is always in the centre of the screen. The chart can be de-cluttered by hiding filtered targets, or vessel names from the display. Page 49 Operation SOG vectors can also be displayed on the screen if this item is selected from the Options menu. Some of the layers displayed on the chart can be removed to provide more clarity on the display. The Chart Settings screen provides a way of modifying these. The chart feature is an aid for the display of information only and should not be used for vessel navigation. 4.6.10 Help and support screen This screen is available from the Home > System Settings menu and provides contact information for the product manufacturer. It also provides relevant information from the User Manual. 4.6.11 User settings screen From this screen, it is possible to set the display brightness, set the display to a day or night colour scheme, and configure the sounds emitted by the device. It is also possible from this screen to set the UTC time offset, change the filter settings and display the menus in a number of non-English languages. 4.7 Configuring vessel information 4.7.1 Pre-configuration checks To proceed with configuration the steps in Section 3. should already have been completed. 4.7.2 Configuring vessel identification information The AIS transceiver must be configured with information about the vessel on which it is installed prior to operation. The following information is required to be entered in the Home > system settings > Vessel data settings menu:

MMSI - Vessel MMSI number, this can usually be found on the ships VHF radio license and should be the same MMSI as used for the VHF / DSC radio. Ship name (limited to 20 characters) Callsign - Vessel radio call sign (limited to 7 characters) Page 50 Operation Ship type - Selected from the menu provided. Reference dimensions of the location of the GNSS antenna connected directly to the AIS transceiver. Please ensure that you enter all vessel data accurately. Failure to do so could result in other vessels failing to identify your vessel correctly. The vessel MMSI can only be programmed once, please take care to program your MMSI correctly. If you need to change the MMSI for any reason, please contact your dealer who will arrange to have the MMSI reset.

!

4.7.3 Configuring the GNSS receiver The GNSS receiver can be configured to operate in one of three modes:

GLONASS and GPS in this mode the position fix is derived from both the GLONASS and GPS network in parallel. This mode is the default setting and gives the best performance. GPS in this mode only GPS satellites are used for the position fix. GLONASS in this mode only GLONASS satellites are used for the position fix. The operating mode can be selected from the GNSS source option in the Home > System settings settings menu. The antenna dimensions should be entered in metres according to the diagram provided in Figure 25. Page 51 Operation Ref C Stern Ref B Ref D GNSS Antenna Ref A Bow Ref A + Ref B = Length in metres Ref C + Ref D = Beam in metres Figure 25 Vessel dimension measurement 4.8 Confirming correct operation Following entry of the vessel information the AIS transceiver will commence normal operation. Correct operation should be verified as follows:

1. Select the Own dynamic data option from the Home menu. 2. Check that the displayed position, course, speed and heading (if appropriate) are correct by comparing the displayed position to other data sources. 3. Check that the TX icon flashes periodically. 4. If the vessel is in an area where other AIS equipped vessels are present press the Back / Home key and select Target list to check that data from other AIS equipped vessels is displayed. 5. Go to the Home > System settings > System Information screen and select Hardware status, check that the supply voltage, forward power, and antenna VSWR are acceptable. A good VSWR is 3:1. A good Forward Power is 37dBm. Page 52 Operation 4.9 Displaying AIS targets 4.9.1 Target list The Target list screen is the primary screen for displaying AIS targets received. This is the first screen displayed when the unit is switched on, but can also be accessed from the Target list option on the Home menu. 16:58:29 SOG 21.1kt COG 88.0 UTC + 1h TARGET LIST 50 32.0286 N 0 55.2715 W 5W

!

NAME/MMSI Range Bearing CPA TCPA Type Age DUBLIN FISHER 3.15NM 120.80 3.15NM PROXIMITY CRAFT 15.5NM 22.60 37.20 313.40

-

15.5NM 6.9NM 6.7NM

-

6.9NM 6.7NM

-

ATLANTIC PRIDE 212222222 EMSLAKE PIER 4 5.2NM 86.60 5.2NM 5h 38m

-

-

-

-

-

BS B B 1m 50s 1m 47s 0m 1s 0m 36s 0m 45s 0m 6s 0m 5s 444110175 35.8NM 167.30 35.8NM

-

Visible: 12 Filtered out: 0 Figure 26 Target list screen By default the Target list is sorted by range but can be sorted on any column by using the left and right Function keys to select a column and pressing the

'Select' key to sort either in ascending or descending order. Navigation up and down the list is via the up and down arrow keys or scroll wheel. Selecting a highlighted target using the Select key will bring up more details of that target. The Options menu on this screen provides additional actions which can be performed on the Target list. Page 53 Operation Different symbols are shown for an AIS target depending on the type of target and its status, these are shown in Figure 27. These symbols are common to the Target list and Target plot displays. AIS Class A AIS Class B B Virtual AIS AtoN BS Base station Off Position AIS AtoN AIS SART AIS AtoN AIS SAR Aircraft Figure 27 AIS target symbols displayed 4.9.2 Target filtering From the Target list options menu, if 'Show Filter Settings' is selected, a screen is displayed indicating which filter parameters can be set to reduce the amount of data displayed on screen. This screen can also be accessed through Home > System settings > User settings. Filters can be toggled on and off on the Target list by pressing the Options menu key and selecting Toggle Filters On / Off. The bottom line of the Target list shows how many targets are visible or filtered out. If a filter is set, the filter icon is displayed at the top of the screen. The Filters icon does not represent CPA/TCPA settings. 4.9.3 CPA/TCPA Settings The AIS transceiver can be configured to identify approaching vessels which fall within certain limits. The Closest Point of Approach (CPA) defines a boundary around the own vessel upon which, if breached, will trigger an alert. Time to Closest Point of Approach (TCPA) can only be set if CPA is set, and will trigger the alert if the time to the CPA limit is breached. These parameters are set on the Home > System settings > User settings

> Filtering and CPA/TCPA Settings menu. The target list shows targets which trigger the CPA/TCPA alert in red. Page 54 Operation These CPA/TCPA figures are calculated solely on AIS data and should not be used for anti-collision purposes. Note: Setting the CPA/TCPA filter will not activate the Filters Icon. 4.9.4 Target plot The Target plot screen shows the location of other AIS equipped vessels and shore stations relative to your own vessel. The Target plot screen provides a basic overview of AIS targets and should not be regarded as a substitute for display of AIS information on a dedicated electronic chart display system

(ECDIS). The plot range can be adjusted by rotating the scroll wheel which cycles through the ranges 0.1NM up to 100NM. The range relates to the radius of the outer range ring shown on the screen. Individual targets can be selected by using the arrow keys. When selected a square outline will appear around the target and the vessel details will be shown on the left hand side of the screen. By pressing the options menu key, additional display features can be selected. If the Own Vessel Details option is selected the left hand side of the screen will change to show own vessel dynamic data. If the MOB Details Display option is selected, the target plot will change to show only AIS-MOB, AIS-SART, and AIS-EPIRB devices. The left hand side of the screen will show the range and relative bearing to whichever target is currently highlighted using the arrow keys. 4.10 Micro SD card data input On the front of the AIS transceiver under the cover on the lower left hand side is a socket for a Micro SD memory card. See Figure 28. This can be used to upgrade the unit firmware, display detailed charts or to log port data. Note the orientation of the Micro SD card, which is critical to ensure the product is not damaged. Page 55 Operation Figure 28 Micro SD card Socket 4.10.1 Loading new charts The AIS transceiver always contains a basic low resolution world chart. More detailed resolution charts can be purchased and overlaid onto the AIS transceivers chart display. The AIS transceiver will read only Jeppesen C-MAP MAX format Micro SD cards. See your dealer for available charts for your region. Insert a C-MAP Micro SD card into the Micro SD card socket. The AIS transceiver will then automatically overlay that higher resolution chart region onto the relevant region on the AIS transceivers world chart. Remove the Micro SD card and the region will revert back to the basic world chart. Page 56 Operation 4.10.2 Upgrading the unit firmware If a Micro SD card that contains valid upgrade firmware is inserted into the card socket, the unit will recognize the new firmware and will display a message asking you if you want to install it. The system will guide you to the appropriate menu screen, where the firmware update can be applied. 4.10.3 Logging ports to the Micro SD card If a Micro SD card is inserted into the card socket, the AIS transceiver can be configured to output specific data to the card. This is accessed from the individual port menu (from the Home > System settings > Interfaces menu.) If the Log port to SD option is set to On, data will be output from that port to the Micro SD card, if one is inserted into the card socket. Only one port can be logged to the Micro SD card at a time. It is also possible to save a copy of the current screen to the Micro SD Card for diagnostics purposes by pressing and holding the rotary controller for at least 3 seconds. 4.10.4 Saving / Loading settings From the Home > System Settings > Advanced > Save / Restore settings menu, all system settings and AIS transceiver configuration data can be saved to the Micro SD card, if one is inserted into the card socket. Settings previously saved can be restored, thus restoring the AIS transceiver to a previous configuration. 4.11 WiFi Feature The AIS transceiver provides features to operate with vessel WiFi networks, or to create its own network. Access the WiFi menu through Home > System settings > Interfaces > WiFi. 4.11.1 Client mode If client mode is selected, the AIS transceiver will search for available WiFi networks to connect to. If one is selected a password may be required, and upon connection the details of the connection will be shown in the bottom right corner of the screen. Once a WiFi connection is made, the AIS transceiver will output a range of NMEA0183 sentences over the selected WiFi port to any connected devices. Page 57 Operation 4.11.2 Access point mode If the AIS transceiver is configured as a WiFi access point (AP) it will create its own WiFi network, allowing other WiFi enabled devices to connect to it. Up to 5 simultaneous connections are supported. Once connections are made, a range of NMEA0183 sentences will be transmitted from the AIS transceiver to any connected devices. 4.11.3 Advanced WiFi features Within the WiFi screen, certain parameters can be changed such as Channel Number, Protocol, Port, Encryption, etc. These are recommended for advanced users only. WiFi is switched off by selecting Disable in the Select operating mode box. Page 58 Technical information 5 Technical information 5.1 AIS Transceiver overall dimensions 152 mm 79 mm 49 mm m m 6 9 1 m m 3 4 1 m m 5 6 1 m m 1 1 1 130 mm Figure 29 AIS Transceiver dimensions Page 59 Technical information 5.2 GNSS Antenna drawing 75 mm*

*

m m 8 6 10m RG58 cable TNC (male) Figure 30 GNSS Antenna

* The dimensions of the supplied antenna may vary from those shown here. Page 60 Technical information 5.3 NMEA 2000 PGN List The PGNs listed in Table 7. are supported by the AIS transceiver. There are no unused fields. Title in NMEA database Usage NMEA 0183 ISO Acknowledgment out ISO Request ISO Address Claim ISO Commanded Address 1ED00 Group Function System time Heartbeat in, out in, out in, out in, out out out Product Information in, out Vessel Heading GNSS Position (Rapid Update) GNSS Direction data GNSS Position data AIS Class A Position Report AIS Class B Position Report AIS Class B Extended Position Report in out out out out out out HDT RMC RMC RMC VDO VDO VDO Page 61 PGN

(Dec.) 059392 059904 060928 065240 126208 126992 126993 126996 127250 129025 129026 129029 129038 PGN

(Hex) 0E800 0EA00 0EE00 0FED8 1F010 1F011 1F014 1F112 1F801 1F802 1F805 1F80E 129039 1F80F 129040 1F810 Title in NMEA database AIS AtoN Report AIS UTC and Date Report AIS Class A Static and Voyage Related Data AIS Addressed Binary Message AIS Acknowledge AIS Binary Broadcast Message AIS SAR Aircraft Position Report AIS Addressed SRM AIS Safety Broadcast Binary Message AIS Class B CS Static Data Report Part A AIS Class B CS Static Data Report Part B Table 7 PGN Lists Usage NMEA 0183 out out out out out out out out out out out VDO VDO VDO VDO VDO VDO VDO VDO VDO VDO VDO Technical information PGN

(Dec.) 129041 129793 PGN

(Hex) 1F811 1FB01 129794 1FB02 129795 1FB03 129796 129797 1FB04 1FB05 129798 1FB06 129801 129802 1FB09 1FB0A 129809 1FB11 129810 1FB12 Page 62 Technical information 5.4 Troubleshooting Issues Possible cause and remedy No data is being received by a connected chart plotter The screen is not illuminated Check that the power supply is connected correctly. Check that the power supply is a 12VDC or 24VDC supply. Check that the connections to the chart plotter are correct. Check that the power supply is connected correctly. Check that the power supply is a 12VDC or 24VDC supply. Press and hold the Chart / Screen brightness button least 5 second. The display should return to maximum brightness. for at Page 63 Technical information The RED Alarm icon is illuminated or flashing The unit may not have a valid MMSI. Check that the AIS transceiver is correctly configured with a valid MMSI. The VHF antenna may be faulty. Please check the connection to the VHF antenna and the VHF antenna is not damaged. The alarm icon may illuminate briefly if the VHF antenna characteristics are briefly affected. that the No GPS position fix can be obtained. Please check the AIS transceiver is located where internal GPS antenna has a clear sky view or that an external GPS antenna is properly connected and installed. Review the GPS signal strength graph in Home >

System settings >

Advanced >

GNSS Source. The power supply the allowable range. Check that the power supply is within the range 10.8VDC to 31.2VDC is outside If none of the above correct the error condition please contact your dealer for advice. Check for error and alarm messages in the Alarms menu. Page 64 My MMSI is being received by other vessels but my vessel name is not shown on their chart plotter or PC. External Sensors not being recognised. VSWR Alarm Activated or High VSWR. Technical information Some older AIS devices and chart plotters do not process the specific class B message which provides the vessel name (message 24). This is not a fault of your AIS transceiver. Software upgrades are available for many older chart plotters which will correct this issue. The other vessel should update its AIS unit and / or chart plotting software to receive AIS message 24. Check Compatibility Mode option in the Interface Settings Menu. Check the Baud Rate set. Check the wiring is correct. Ensure VHF Antenna is as far away as possible from metallic structures and any other antennae. Ensure VHF Antenna is as high as possible. Ensure VHF Antenna is suitable for AIS i.e. 3dBi Gain, 156-162MHz, and uses high quality RG213 or RG214 cable. The VHF Antenna cable should be as short as possible and no more than 30 metres (100ft) in length. Table 8 Troubleshooting If the guidance given in the table above does not rectify the problem you are experiencing, please contact your dealer for further assistance. Page 65 Technical information Page 66 Technical specification 6 Technical specification 6.1 Applicable equipment standards IEC62287-2 Ed. 1.0 2013-03 IEC60945 4th Ed. 2002-08 IEC61162-1 Ed. 4.0 2010-11 IEC61162-2 Ed. 1.0 1998-09 IEC61162-3 2008+A2:2014 Maritime navigation and radiocommunication equipment and systems - Class B shipborne equipment of the universal automatic identification system (AIS) Part 2: Self-organising time division multiple access (SOTDMA) techniques Maritime navigation and radio communication equipment and systems General requirements Methods of testing and required test results Maritime navigation and radio communication equipment and systems Digital interfaces - Single talker and multiple listeners Maritime navigation and radio communication equipment and systems Digital interfaces - Single talker and multiple listeners, high speed transmission Maritime navigation and radio communication equipment and systems -

Digital interfaces - Part 3: Serial data instrument network Page 67 Technical specification ITU-R M.1371-5 02/2014 Technical characteristics for an automatic identification system using time division multiple access in the VHF maritime mobile band IEC61108-1 2nd Ed. 2003-07 IEC6118-02 1st Ed. 1998-06 Global Navigation Satellite Systems (GNSS) Part 1: Global positioning system (GPS) - Receiver equipment - Performance standards, methods of testing and required test results Global navigation satellite systems (GNSS) - Part 2:

Global navigation satellite system (GLONASS) -

Receiver equipment - Performance standards, methods of testing and required test results 6.2 Product category Product category This product is categorised as protected in accordance with the definitions provided in IEC 60945 6.3 Physical AIS Transceiver dimensions 152mm x 165mm x 111mm (WxHxD), see Figure 29. for drawing) AIS Transceiver weight 1.5kg Compass safe distance Safe operating distance 0.5m (AIS Transceiver) 20cm from the antenna Page 68 Technical specification 6.4 Environmental Operating temperature range Maximum operating humidity

-15C to +55C 90% at +40C, non-condensing Water ingress rating IPx6, IPx7 6.5 Electrical Supply voltage 12VDC to 24VDC (absolute min 10.8V, absolute max 31.2 V) Power consumption

< 12W Current consumption

@12 VDC supply Current consumption

@24 VDC supply 0.9A typical, 4.0A peak 0.5A typical, 3.0A peak 6.6 Display and user interface Display Luminance Recommended viewing distance Keypad 800 x 480 pixel colour LCD with adjustable backlight 500cd/m2 max, 75cd/m2 default 45cm Five function keys and three menu keys with adjustable backlight Rotary control Encoder with push function Speaker 600mW@750Hz 11mm x 15mm Page 69 Technical specification 6.7 Internal GNSS Receiver channels 32 channels GPS and GLONASS operating modes Time to first fix Typically 26 seconds Frequency Accuracy Antenna requirement L1 GPS band, 1575.42MHz and L1 GLONASS band 1597.1 - 1609.5MHz 2.5m CEP / 5.0m SEP without differential correction 2.0m CEP / 3.0m SEP with SBAS or RTCM DGPS correction Active antenna (5V bias) with gain >15dB 6.8 TDMA Transmitter Frequency range 156.025MHz to 162.025MHz Channel bandwidth 25kHz Output power 1W or 5W (automatic selection) Data transmission rate 9600 bits/s Modulation mode 25kHz GMSK 6.9 TDMA Receiver Number of receivers Frequency range Channel bandwidth Sensitivity Page 70 2 156.025MHz to 162.025MHz 25kHz

<-107dBm for 20% PER Technical specification Modulation mode 25kHz GMSK Adjacent channel selectivity Spurious response rejection 70dB 70dB 6.10 DSC Receiver Number of receivers 1 Frequency 156.525MHz (Channel 70) Channel bandwidth 25kHz Sensitivity Modulation mode

-107dBm @ BER <10-2 25kHz AFSK Adjacent channel selectivity Spurious response rejection 70dB 70dB 6.11 RF Connections VHF Antenna connection VHF Port impedance GNSS Antenna connections GNSS Port impedance SO-239 / UHF 50 Ohms TNC female 50 Ohms Page 71 Technical specification 6.12 WiFi Maximum output power IEEE 802.11g/n Maximum output power IEEE 802.11b

+15dBm

+17dBm 6.13 Data interface Sensor data input ports Number of ports 3 Standard Baud rate IEC61162-1 / -2 4800 baud or 38400 baud Port impedance 54K Ohms Bi-directional data ports Number of ports 3 Standard Baud rate IEC61162-1 / -2 4800 or 38400 baud Port impedance 54K Ohms Page 72 Technical specification Silent Mode port Port impedance NMEA 2000 Port:

Load equivalency number (LEN) 10K Ohms 1 6.14 Power and data connector information Power connector Chogori 22002525-04-RC 18 way data connector Chogori 23018525-04-RC 14 way data connector Chogori 23014525-05-RC Mating Half Mating Half Mating Half Chogori 22002221-01 Chogori 23018221-01 Chogori 23014221-01 6.15 Open source licences This product contains open source software. For details please see the System information screen. Page 73 Technical specification Page 74 Manufacturers code: 427 NMEA 2000 Product code: 23810 201-0856:1