AI-Link WIFI-2-Q379UWP1 WiFi Module Integrated Bluetooth 2.1+EDR/3.0+HS/4.2 Features Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac Bluetooth 2.1+EDR/3.0+HS/4.2 Chip Solution Qualcomm9379-7 Size 33.0mm x70.0mm x 6.0mm Model Overview Model Standard Rate Band WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 866.7Mbps 2.4G/5G BT2.1+EDR/3.0+HS/4.2 3Mbps 2.4G Antenna Internal Antennas Design Power 5V Sichuan AI-Link Technology Co.,Ltd. Add: Anzhou,Industrial park,Mianyang,Sichuan Web: http://www.changhong.com AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 1. Introduction WIFI-2-Q379UWP1 module design is based on Qualcomm9379-7 solution, The QCA9379-7 is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio and Bluetooth radio. It includes Bluetooth EDR and LE radio which complies with Bluetooth v2.1+EDR, v3.0+HS, and v4.2. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Qualcomm QCA9379-7. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11 specification and Bluetooth over USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent Wi-Fi/Bluetooth coexistence algorithm is implemented to provide the best harmonized Wi-Fi and Bluetooth radio performance. 5V INPUT GPIO 2.4G TX0/RX0 WF_ RFIO 5G TX0/RX0 Dixplexer Antenna0 WLAN USB2.0 Interface QCA9379-7 BT USB1.1 Interface 2.4G TX1/RX1 WF_ 5G TX1/RX1 RFIO Dixplexer Antenna1 48MHz BT_ RFIO BT TX2/RX2 Filter Antenna2 Figure 1 WIFI-2-Q379UWP1 Block Diagram Sichuan AI-Link Technology Co.,Ltd. page 2 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac _ Bluetooth 2.1+EDR/3.0+HS/4.2 1.3 System Functions Table1: General Specification as below:
Main Chipset Operating Frequency WiFi Standard Bluetooth Modulation Data rates Form factor Host Interface PCB Stack Dimension Antenna Operation Temperature Storage Temperature Operation Voltage Qualcomm QCA9379-7 2.4G/5G 802.11a/b/g/n/ac (2x2) 2.1+EDR/3.0+HS/4.2 WIFI:11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM BT: FHSS,GFSK,DPSK,DQPSK 11b: 1, 2, 5.5 and 11Mbps 11a/g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps 11ac: MCS0~9, Nss=2, up to 866.7Mbps 13pins , USB 2.0 for WLAN and USB 1.1 for BT 6-layers design Typical33mm x 70mm x 6mm Internal Antennas Design 0 to +70
-15 to +45 5V +/-10%
Sichuan AI-Link Technology Co.,Ltd. page 3 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L ): 33.0mmx 70.0mm x 6.0mm General tolerance: 0.15mm TOP VIEW BOTTOM VIEW 2.2 Product Picture TOP VIEW BOTTOM VIEW Sichuan AI-Link Technology Co.,Ltd. page 4 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 2.3 Pin definition No 1 Define WIFI_REG_ON description WLAN enableactive high BT_HOST_WAKE Bluetooth wakeup the hostactive high 2 3 4 5 6 7 WL_VCC WI-FI DN WIFI DP GND 3D_SYNC Reset 8 9 WLAN_DEV_WAKE 10 11 12 13 BTDN BTDP GND BT_VCC WLAN 5V input WIFI USB D-/DN WIFI USB D+/DP Ground Frame sync signals from TV to sync with 3D glass via Bluetooth Bluetooth enableactive high WIFI wakeup the host, active high BT 5V input BT USB D-/DN BT USB D-/DP Ground Sichuan AI-Link Technology Co.,Ltd. page 5 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0,+25,+40) and overall voltage (4.5V,5.0V,5.5V). 3. 1 IEEE 802.11g/a Section:
Items Contents Specification Mode Channel Data rate IEEE802.11g & IEEE802.11a BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 11g CH36 to CH165 @ 11a 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 14.5dBm Target (For Each antenna port)
@ 11g 54Mbps 2) 13.5dBm Target (For Each antenna port)
@ 11a 54Mbps 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 4. Frequency Error 1) IEEE802.11g 2) IEEE802.11a RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%) 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%) 6. Maximum Input Level (PER 10%) 1) IEEE802.11g 2) IEEE802.11a 12 12 14.5 13.5 16 15
-20
-28
-40
-5
-8
-10
-13
-16
-19
-22
-25 25 30
-
-
-
-
-
-
-
-
-
-
-
-
Typ. Max.
-
-
-
-
-
-
-
-
-
-82
-81
-79
-77
-74
-70
-66
-65
-
dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-30 Min.
-
-
-
-
-
-
-
-
-20
-30 Sichuan AI-Link Technology Co.,Ltd. page 6 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3.2 IEEE 802.11b Section:
Items Specification Mode Channel Data rate Contents IEEE802.11b DBPSK, DQPSK and CCK and DSSS CH1 to CH13 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port)
@1Mbps~11Mbps 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3. Constellation Error(EVM) @ Target Power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER 8%) 2) 2Mbps (FER 8%) 3) 5.5Mbps (FER 8%) 4) 11Mbps (FER 8%) 6. Maximum Input Level (FER 8%) 16 17.5 19 dBm
-
-
-
-
-
-
-25 Min.
-
-
-
-
-10
-
-
-
-
-
-20
-
Typ.
-83
-80
-79
-76
-
-30
-50
-10
-10
-10
-10 25 Max.
-76
-76
-76
-76
-
dBr dBr dB dB dB dB ppm Unit dBm dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 7 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3.3 IEEE 802.11n HT20 Section:
Items Specification Mode Channel Contents IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 2.4G CH36 to CH165 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 14.5dBm Target (For Each antenna port)
@ 2.4G/MCS7 2) 13.5dBm Target (For Each antenna port)
@ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level (PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G 13 12 14.5 13.5 16 15
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 25 20
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ. Max.
-
-
-
-
-
-
-
-
-
-
-82
-79
-77
-74
-70
-66
-65
-64
-
-
dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-20 Min.
-
-
-
-
-
-
-
-
-20
-30 Sichuan AI-Link Technology Co.,Ltd. page 8 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3.4 IEEE 802.11n HT40 Section:
Items Specification Mode Channel Contents IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH3 to CH11 @ 2.4G CH38 to CH163 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 13.5dBm Target (For Each antenna port)
@ 2.4G/MCS7 2) 12.5dBm Target (For Each antenna port)
@ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz 2) at fc +/-40MHz 3) at fc > +/-60MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level(PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G 12 11 13.5 12.5 15 14
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 25 20
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ. Max.
-
-
-
-
-
-
-
-
-
-
-79
-76
-74
-71
-67
-63
-62
-61
-
-
dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-20 Min.
-
-
-
-
-
-
-
-
-20
-30 Sichuan AI-Link Technology Co.,Ltd. page 9 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3.5 IEEE 802.11ac Section:
Items Specification Mode Channel Data rate (MCS index) Contents IEEE802.11ac BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM CH36 to CH165 VHT20 CH38 to CH163 VHT40 CH42 to CH157 VHT80 MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 12.5dBm Target (For Each antenna port)
@VHT20 MCS8 2) 10.5dBm Target (For Each antenna port)
@VHT40 MCS9 3) 9.5dBm Target (For Each antenna port)
@VHT80 MCS9 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz 2) at fc +/-21MHz /40MHz/60MHz 3) at fc +/-41MHz /80MHz/120MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 9) MCS8 10) MCS9 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 9) MCS8 (PER 10%) 10) MCS9 (PER 10%) 6. Maximum Input Level(PER 10%) 11 9 8
-
-
-
-
-
-
-
-
-
-
-
-10 Min.
-
-
-
-
-
-
-
-
-
-
-30 12.5 10.5 9.5
-
-
-
-
-
-
-
-
-
-
-
-
14 12 11
-20
-28
-40
-5
-10
-13
-16
-19
-22
-25
-27
-30
-32 10 Typ. Max. VHT20 VHT40 VHT80
-
-
-
-
-
-
-
-
-
-
-
-82
-79
-77
-74
-70
-66
-65
-64
-59
-57
-79
-76
-74
-71
-67
-63
-62
-61
-56
-54
-
-76
-73
-71
-68
-64
-60
-59
-58
-53
-51 dBm dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB dB dB ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 10 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 3.6 Bluetooth Section:
Items Specification Mode Number of Channel Frequency Band 1. Output Power 2.Gain step 3. Receiver sensitivity (BER 0.1%) 4. Maximum usable signal (BER 0.1%) 5. C/I co-channel (BER<0.1%) 6. C/I 1MHz (BER<0.1%) 7. C/I 2MHz (BER<0.1%) 8. C/I3MHz (BER<0.1%) 9. C/I Image channel (BER<0.1%) 10. C/I Image 1MHz (BER<0.1%) 11. Inter-modulation 12. Out-of-band blocking 1). 30MHz to 2000MHz 2). 2000MHz to 2399MHz 3). 2498MHz to 3000MHz 4). 3000MHz to 12.75GHz 13. Modulation characteristics 1). f1avg 2). f2max (For at least 99.9% of all f2max) 3). f1avg /f2avg 14. ICFT 15. Carrier frequency drift 1). One slot packet (DH1) 2). Two slot packet (DH3) 3). Five slot packet (DH5) 4). Max drift rate 16. TX output spectrum(20dB bandwidth) 17. In-Band spurious emission 1). 2MHz offset 2). 3MHz offset 3). >3MHz offset Min. 7.5 2
-
-
-
-
-
-
-
-
-
-10
-27
-27
-10 140 115 0.8
-75
-25
-40
-40
-
-
-
-
-
Contents BT2.1+EDR/4.2/5.0 FHSS,GFSK,DPSK,DQPSK 79 Channels Typ. 9 4 Max. 2.402 GHz ~2.480GHz Unit dBm dB dBm
-93.5 Remark
-
8
-80
-
11 0
-30
-40
-9
-20
-
-
-
-
-
175
-
-
+75
+25
+40
+40 20 dB dB dB dB dB dB dB dBm dBm dBm dBm KHz KHz KHz KHz KHz KHz KHz KHz/50us 1000 KHz
-20
-40
-40 dBm dBm dBm
-5 4
-14
-42
-49
-25
-50
-13
-
-
-
-
157 140 0.98 20 15 15 15 6 922
-45
-48
-48 Sichuan AI-Link Technology Co.,Ltd. page 11 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 4. Current consumption Description Average currentmA Wi-Fi Standby mode current BT Standby mode current:
Power Saving Mode Wi-Fi cont. TX mode Wi-Fi cont. Rx mode BT cont. TX mode BT cont. Rx mode 30mA 15mA 2.2mA 610mA 260mA 50mA 25mA 5. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is QDART Sichuan AI-Link Technology Co.,Ltd. page 12 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 6. Package Pallet size Line of production Sichuan AI-Link Technology Co.,Ltd. page 13 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 Packing desrciption:
Pallet 15 layers 30 Other requirements are subject to the standard of hisense. Sichuan AI-Link Technology Co.,Ltd. page 14 of 14 AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device . FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:2AOKI-WIFI2Q379UWP1 Or Contains FCC ID:2AOKI-WIFI2Q379UWP1 When the module is installed inside another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Sichuan AI-Link Technology Co.,Ltd. AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. IC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device. This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or t ransmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Cette modulaire doit tre install et utilis une distance minimum de 20cm entre le radiateur et le corps de l'utilisateur. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
"Contains IC: "
23460-WFQ379UWP1 when the module is installed inside another device, the user manual of this device must contain below warning statements;
1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interfrences ; et
( 2 ) Ce dispositif doit accepter toute interfrence , y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product Sichuan AI-Link Technology Co.,Ltd. AI-Link WIFI-2-Q379UWP1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2 NB Statement Herby,Sichuan AI-Link Technology Co., Ltd.declares that this WiFi Module, WIFI-2-Q379UWP1 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states. Use the WiFi Module in the environment with the temperature between 0 and 60 Operation Frequency:
For BT/BLE:
2402MHz~2480MHz For 2.4G WIFI:
2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20)) 2422MHz~2462MHz (802.11n(HT40)) For 5G WIFI:
5150MHz-5350MHz, 5470MHz-5725MHz, 5745MHz-5825MHz Max output power:
BT: 0.0048W BLE: 0.0008W Wifi(2.4G): 0.0637W Wifi(5G): 0.0596W Manufacturer: Sichuan AI-Link Technology Co., Ltd. Address: Anzhou, Industrial park, Mianyang, Sichuan, China Tel: +86-0816-2438701 Fax: +86-0816-2438701 E-mail: caixia.hu@changhong.com Sichuan AI-Link Technology Co.,Ltd.