| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
AirPrime - HL6528x - Product Technical Specification | Users Manual | 1.78 MiB | June 06 2014 / September 12 2014 | |||
| 1 | Cover Letter(s) | June 06 2014 / November 06 2014 | ||||||
| 1 | Cover Letter(s) | June 06 2014 / November 06 2014 | ||||||
| 1 | RF Exposure Info | June 06 2014 / November 06 2014 | ||||||
| 1 | External Photos | June 06 2014 / September 12 2014 | ||||||
| 1 | Internal Photos | June 06 2014 / September 12 2014 | ||||||
| 1 | ID Label/Location Info | June 06 2014 / November 06 2014 | ||||||
| 1 | Test Setup Photos | June 06 2014 / September 12 2014 | ||||||
| 1 | Test Report | June 06 2014 / November 06 2014 |
| 1 | AirPrime - HL6528x - Product Technical Specification | Users Manual | 1.78 MiB | June 06 2014 / September 12 2014 |
Product Technical Specification AirPrime HL6528x 4114016 3.0 January 28, 2014 Product Technical Specification Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note:
Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operators control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitations of Liability This manual is provided as is. Sierra Wireless makes no warranties of any kind, either expressed or implied, including any implied warranties of merchantability, fitness for a particular purpose, or noninfringement. The recipient of the manual shall endorse all risks arising from its use. The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS) services. These services are provided by a third party and should be purchased directly by the Customer. 4114016 Rev 3.0 January 28, 2014 2 Product Technical Specification SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS) SERVICES. Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright 2014 Sierra Wireless. All rights reserved. Trademarks Sierra Wireless, AirPrime, AirLink, AirVantage, WISMO and the Sierra Wireless and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries. Watcher is a registered trademark of NETGEAR, Inc., used under license. Windows and Windows Vista are registered trademarks of Microsoft Corporation. Macintosh and Mac OS X are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Phone:
1-604-232-1488 Sales Desk:
Hours:
8:00 AM to 5:00 PM Pacific Time Contact:
http://www.sierrawireless.com/sales Post:
Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Technical Support: support@sierrawireless.com RMA Support:
repairs@sierrawireless.com Fax: 1-604-231-1109 Web: http://www.sierrawireless.com/
Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com 4114016 Rev 3.0 January 28, 2014 3 Product Technical Specification Document History Version Date Updates April 4th, 2013 Creation May 13, 2013 Footprint definition update May 24, 2013 Mechanical definition change, 0.1 0.2 0.3 0.4 May 31, 2013 0.5 June 7, 2013 0.6 June 8, 2013 Padout definition change Mechanical definition change Add product label Correct max current Correct padout definition Add 2G_TX_ON information Add VBATT_PA information Added:
4 pin UART0 0.7 July 12, 2013 References section UIM1_DET and UIM2_DET signal on default pins 1.0 July 23, 2013 Terms and Abbreviations chapter Corrected Module Tolerance Changed HL6528-G VBATT Max to 4.5V Major changes to pin definitions:
UART0 removed Add SPI for SW Traces Change IC location Add TP1,TP2 pins Added customer guidelines including:
Power_on sequence ESD Audio design Radio design Added:
CF3 pin information 2.0 October 24, 2013 Antenna detection circuitry Updated:
New product variants (HL6528-2.8V and HL6528-G2.8V) 3.0 January 28, 2014 Module thickness from 2.55mm to 2.50mm Pin 57 to support BUZZER output Section 2 Pad Definition Added:
Weight in section 1.2 Physical Dimensions 1.4 Feature Restriction Table 38 AirPrime HL6528x FCC IDs Table 39 AirPrime HL6528x IC Updated:
3.2 Current Consumption 3.5 UIM Interface 3.18 GNSS Interface 4114016 Rev 3.0 January 28, 2014 4 Contents 1. INTRODUCTION ................................................................................................ 10 Common Flexible Form Factor (CF3) .............................................................................. 10 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. 1.7. 1.8. 1.9. Physical Dimensions ....................................................................................................... 11 General Features ............................................................................................................. 11 Feature Restriction .......................................................................................................... 12 GNSS Features ............................................................................................................... 12 Architecture ..................................................................................................................... 13 Interfaces ......................................................................................................................... 13 Connection Interface ....................................................................................................... 14 ESD ................................................................................................................................. 14 1.10. Environmental and Certifications ..................................................................................... 15 1.10.1. Environmental Specifications ................................................................................... 15 1.10.2. Regulatory ................................................................................................................ 15 1.10.3. RoHS Directive Compliant ....................................................................................... 17 1.10.4. Disposing of the Product .......................................................................................... 17 1.10.5. References ............................................................................................................... 17 2. PAD DEFINITION ............................................................................................... 18 Pin Configuration (Top View) ................................................................................... 23 2.1.1. 3. DETAILED INTERFACE SPECIFICATIONS ..................................................... 24 3.1. 3.2. 3.3. 3.4. 3.5. Power Supply .................................................................................................................. 24 Current Consumption ...................................................................................................... 24 VGPIO ............................................................................................................................. 26 BAT_RTC ........................................................................................................................ 27 UIM Interface ................................................................................................................... 27 UIM1 Interface .......................................................................................................... 27 UIM2 Interface .......................................................................................................... 28 3.5.1. 3.5.2. 3.6. 3.7. 3.8. 3.9. Electrical Information for Digital I/O ................................................................................. 29 Main Serial Link (UART1) ................................................................................................ 30 Power On Signal (PWR_ON) .......................................................................................... 31 Reset Signal (RESET) ..................................................................................................... 32 3.10. ADC ................................................................................................................................. 32 3.11. Analog Audio Interfaces .................................................................................................. 32 3.11.1. Analog Audio Input ................................................................................................... 33 3.11.2. Analog Audio Outputs .............................................................................................. 33 3.12. 3.13. PCM ................................................................................................................................. 34 I2C Interface ..................................................................................................................... 35 3.14. Debug Interfaces ............................................................................................................. 35 3.14.1. SW Traces ................................................................................................................ 35 4114016 Rev 3.0 January 28, 2014 5 Product Technical Specification 3.14.2. JTAG ........................................................................................................................ 36 3.15. 3.16. PPS (HL6528-G and HL6528-G2.8V only)...................................................................... 36 EXT_LNA_GPS_EN (HL6528-G and HL6528-G2.8V only) ............................................ 37 3.17. RF Interface ..................................................................................................................... 37 3.17.1. RF Connection ......................................................................................................... 37 3.17.2. RF Performances ..................................................................................................... 37 3.17.3. TX Burst Indicator (2G_TX_ON) .............................................................................. 37 3.18. GNSS Interface ............................................................................................................... 38 3.18.1. GNSS Performances ................................................................................................ 39 3.18.2. GNSS Antenna Interface .......................................................................................... 39 3.18.3. GNSS Antenna Recommendations ......................................................................... 40 3.19. GPIO RESET/ DEFAULT states ..................................................................................... 40 4. MECHANICAL DRAWINGS ............................................................................... 43 5. DESIGN GUIDELINES ....................................................................................... 46 5.1. 5.2. 5.3. 5.4. Power-Up Sequence ....................................................................................................... 46 Module Switch-Off ........................................................................................................... 46 Sleep Mode Management ............................................................................................... 47 ESD Guidelines for UIM Cards ........................................................................................ 47 5.5. Audio Integration ............................................................................................................. 48 5.5.1. Microphone Audio Design ........................................................................................ 48 Speaker Audio Design ............................................................................................. 50 5.5.2. 5.5.3. Audio Layout Guidelines .......................................................................................... 51 5.6. Radio Integration ............................................................................................................. 53 RF Routing Recommendations ................................................................................ 53 GSM Antenna Integration with Antenna Detection Circuitry .................................... 55 GNSS Active Antenna Integration ............................................................................ 56 5.6.1. 5.6.2. 5.6.3. 6. X-RAY EXPOSURE ............................................................................................ 57 7. FLASH MEMORY ENDURANCE ....................................................................... 57 8. FCC/IC LEGAL INFORMATION ......................................................................... 57 8.1. 8.2. 8.3. 8.4. Label ................................................................................................................................ 57 FCC Regulations ............................................................................................................. 58 RF Exposure Information ................................................................................................ 58 IC Regulations ................................................................................................................. 59 9. ORDERING INFORMATION .............................................................................. 61 10. TERMS AND ABBREVIATIONS ........................................................................ 62 4114016 Rev 3.0 January 28, 2014 6 List of Figures Figure 1. AirPrime HL6528x Architecture Overview ....................................................................... 13 Figure 2. AirPrime HL6528x Module Mechanical Overview ........................................................... 14 Figure 3. Pin Configuration ............................................................................................................. 23 Figure 4. UIM2 with an Analog Switch ............................................................................................ 29 Figure 5. PWR_ON Sequence ....................................................................................................... 31 Figure 6. PCM Timing Waveform ................................................................................................... 35 Figure 7. 2G_TX_ON State during TX Burst .................................................................................. 38 Figure 8. AirPrime HL6528x (angular view) .................................................................................... 43 Figure 9. AirPrime HL6528x (side view) ......................................................................................... 44 Figure 10. AirPrime HL6528x Module (top view) .............................................................................. 44 Figure 11. AirPrime HL6528x Module (bottom view with dimensions) ............................................. 45 Figure 12. UART Signals during the Power ON Sequence .............................................................. 46 Figure 13. Power OFF Sequence for PWR_ON, VGPIO and CTS .................................................. 46 Figure 14. EMC and ESD Components Close to the UIM ................................................................ 47 Figure 15. Example of a MIC Input Connection with LC Filter ......................................................... 48 Figure 16. Example of a MIC Input Connection without LC Filter .................................................... 48 Figure 17. Example of a Single-Ended MIC Input Connection with LC Filter ................................... 49 Figure 18. Example of a Single-Ended MIC Input Connection without LC Filter .............................. 49 Figure 19. Example of a Differential Connection for SPKR .............................................................. 50 Figure 20. Example of a Single-Ended Speaker Connection (typical implementation) .................... 51 Figure 21. Audio Track Design ......................................................................................................... 51 Figure 22. Differential Audio Connection .......................................................................................... 52 Figure 23. Single-Ended Audio Connection ..................................................................................... 52 Figure 24. AppCAD Screenshot for Microstrip Design Power Mode Diagram ................................. 53 Figure 25. RF Routing Examples ..................................................................................................... 54 Figure 26. Coplanar Clearance Example ......................................................................................... 54 Figure 27. Antenna Microstrip Routing Example .............................................................................. 55 Figure 28. GSM Antenna Connection with Antenna Detection ........................................................ 55 Figure 29. GNSS Application with Active Antenna ........................................................................... 56 4114016 Rev 3.0 January 28, 2014 7 List of Tables Table 1. Supported Frequencies ................................................................................................... 10 Table 2. AirPrime HL6528x Features ............................................................................................ 11 Table 3. GNSS Capabilities ........................................................................................................... 12 Table 4. AirPrime HL6528x Module Environmental Specifications ............................................... 15 Table 5. Regulation Compliance ................................................................................................... 15 Table 6. Pad Description ............................................................................................................... 18 Table 7. Power Supply .................................................................................................................. 24 Table 8. Current Consumption ...................................................................................................... 24 Table 9. Current Consumption per power supply VBATT / VBATT_PA ....................................... 25 Table 10. VGPIO Electrical Characteristics ..................................................................................... 26 Table 11. BAT_RTC Electrical Characteristics................................................................................ 27 Table 12. Electrical Characteristics of UIM1 ................................................................................... 27 Table 13. Electrical Characteristics of UIM2 ................................................................................... 28 Table 14. UIM2_VCC_CTRL Analog Switch Truth Table ............................................................... 29 Table 15. Digital I/O Electrical Characteristics ................................................................................ 29 Table 16. UART1 Pin Description ................................................................................................... 30 Table 17. PWR_ON Electrical Characteristics ................................................................................ 31 Table 18. ADC Electrical Characteristics ........................................................................................ 32 Table 19. Analog Audio Interface Input ........................................................................................... 33 Table 20. Analog Audio Interface Output ........................................................................................ 33 Table 21. Recommended Speaker Characteristics ......................................................................... 33 Table 22. Table 23. Digital Audio Interface Electrical Characteristics ............................................................. 34 I2C Pin Description .......................................................................................................... 35 Table 24. SPI Pin Description ......................................................................................................... 36 Table 25. JTAG Pin Description ...................................................................................................... 36 Table 26. PPS Electrical Characteristics ......................................................................................... 36 Table 27. EXT_LNA_GPS_EN Electrical Characteristics ............................................................... 37 Table 28. RF Connection................................................................................................................. 37 Table 29. Burst Indicator States ...................................................................................................... 38 Table 30. TX Burst Characteristics .................................................................................................. 38 Table 31. GNSS Interface Specifications ........................................................................................ 39 Table 32. GNSS Antenna Specifications ......................................................................................... 39 Table 33. GNSS Antenna Recommendations ................................................................................. 40 Table 34. Pad Description ............................................................................................................... 40 Table 35. Recommended Components for a Microphone Connection ........................................... 49 Table 36. Recommended Components for a Single-Ended Microphone Connection .................... 50 Table 37. Speaker Details ............................................................................................................... 50 4114016 Rev 3.0 January 28, 2014 8 Product Technical Specification Table 38. AirPrime HL6528x FCC IDs ............................................................................................ 58 Table 39. AirPrime HL6528x IC number ......................................................................................... 60 4114016 Rev 3.0 January 28, 2014 9 1. Introduction This document defines the high level product features and illustrates the interfaces for the AirPrime HL6528x series of embedded modules. This document is intended to cover the hardware aspects of the product series, including electrical and mechanical. Variants covered in this document are:
HL6528 HL6528-G HL6528-2.8V HL6528-G2.8V The AirPrime HL6528 and HL6528-G modules are 1.8V IO modules as defined in section 2 Pad Definition. 2.8V IO variants are also available, and defined throughout this document as HL6528-2.8V and HL6528-G2.8V. HL6528x denotes applicability to all four variants. The AirPrime HL6528x belongs to the AirPrime HL Series from Essential Connectivity Module family. This is an Industrial Grade quad-band GSM/GPRS Embedded Wireless Module, designed for the automotive market and any other market with similar quality and life-time support requirements. The following table enumerates the frequencies supported by the HL6528x module. Table 1. Supported Frequencies RF Band Transmit band (Tx) Receive band (Rx) Maximum Output Power GSM 850 E-GSM 900 DCS 1800 PCS 1900 824 to 849 MHz 869 to 894 MHz 2 Watts GSM & GPRS 880 to 915 MHz 925 to 960 MHz 2 Watts GSM & GPRS 1710 to 1785 MHz 1805 to 1880 MHz 1 Watt GSM & GPRS 1850 to 1910 MHz 1930 to 1990 MHz 1 Watt GSM & GPRS This module supports a large variety of interfaces such as Analog & Digital Audio and Dual UIM Dual Standby to provide customers with the highest level of flexibility in implementing high-end solutions. In addition to having the same features as AirPrime HL6528 and HL6528-2.8V modules, the AirPrime HL6528-G and HL6528-G2.8V modules also embed a high-performance GNSS receiver. 1.1. Common Flexible Form Factor (CF3) The AirPrime HL6528x module belongs to the Common Flexible Form Factor (CF3) family of modules. This family consists of a series of WWAN modules that share the same mechanical dimensions (same width and length with varying thicknesses) and footprint. The CF3 form factor provides a unique solution to a series of problems faced commonly in the WWAN module space as it:
Accommodates multiple radio technologies (from 2G to LTE advanced) and band groupings Supports bit-pipe (Essential Module Series) and value add (Smart Module Series) solutions Offers electrical and functional compatibility Provides Direct Mount as well Socketability depending on customer needs 4114016 Rev 3.0 January 28, 2014 10 Product Technical Specification Introduction 1.2. Physical Dimensions The AirPrime HL6528x modules are compact size, robust, fully shielded modules with:
Length: 23 mm Width: 22 mm Thickness: 2.50 mm (including the label) Weight : 2.25g Note:
Dimensions specified above are typical values. 1.3. General Features The table below summarizes the AirPrime HL6528x module features. Table 2. AirPrime HL6528x Features Feature Description GSM/DCS Output Power GPRS Class 4 (2 W) for GSM 850 and E-GSM Class 1 (1 W) for DCS and PCS Quad-band GSM850/E-GSM/DCS/PCS GPRS Multi-slot class 10 R99 support PBCCH support Coding schemes: CS1 to CS4 Analog and Digital interfaces Audio Interface Adaptive Multi Rate (AMR) Supports Full Rate (FR), Enhanced Full Rate (EFR), Half Rate (HR) and UIM Interface Application Interface SMS Supplementary Services Noise reduction and echo cancellation DTMF generation Dual UIM Dual Standby support 1.8V/3.0V support for UIM1 3V interface for UIM2 Supports UIM application tool kit with proactive UIM commands Full set of AT commands for GSM/GPRS including GSM 07.07 and 07.05 AT command sets Comprehensive set of dedicated AT commands for M2M applications SMS class 0,1 and 2 SMS MT, MO SMS storage into UIM card or Flash memory Concatenation of MT SMS Call Forwarding Call Barring Multiparty Service Call Waiting Call Hold USSD Automatic answer 4114016 Rev 3.0 January 28, 2014 11 Product Technical Specification Introduction Feature Description RTC Real Time Clock (RTC) with calendar and alarm Temperature Sensor Temperature monitoring Alarms 1.4. Feature Restriction The AirPrime HL6528-G and HL6528-G2.8V modules are not compatible with TTS (Text To Speech) feature, which is part of AVL (Automatic Vehicle Location) feature. 1.5. GNSS Features The table below summarizes the GNSS capabilities of the AirPrime HL6528-G and HL6528-G2.8V modules. Table 3. GNSS Capabilities Feature Description GPS L1 band (CDMA 1575.42 MHz) GLONASS L1 Band (FDMA 1602MHz) SBAS Channels Antenna Assistance data WAAS, EGNOS, MSAS, GAGAN, QZSS 52 Passive or active antenna support Server-generated Extended Ephemeris 4114016 Rev 3.0 January 28, 2014 12 Product Technical Specification Introduction 1.6. Architecture The figure below presents an overview of the AirPrime HL6528x module internal architecture and external interfaces. Note:
Dotted parts are only supported on the AirPrime HL6528-G and HL6528-G2.8V. Figure 1. AirPrime HL6528x Architecture Overview 1.7. Interfaces The AirPrime HL6528 and HL6528-2.8V modules provide the following interfaces and peripheral connectivity:
1 8-pin UART Active Low RESET Active Low POWER-ON 1 1.8V/3V UIM 1 UIM 3V 1 Analog Audio Interface (Differential input/output) 1 Digital Audio 2 ADC 1 JTAG Interface 8 GPIOs with IC multiplexes 2G TX Burst Indicator GSM Antenna Note: SPI interface is ONLY dedicated to SW traces debug. 4114016 Rev 3.0 January 28, 2014 13 HL6528xMemory(Flash + RAM)GNSSSAWFiltersGSMPA&SwitchCTRLDATA16.369MHz26MHz32.768KHzUART1 (8pins)SPIVBATGNDVGPIOVBAT_RTCGPIO x8ADC x2ICMICSPEAKERPCMRFRFJTAGLGA-146 BasebandEXT_LNA_GPS_ENPPSSAWFilterRFLNASIM2SIM1MCUDSPPMURFAnalog BasebandPeripheralsRX_HBRX_LBLBLBHBHBTX_LBTX_HBLGA-146 2G_TX_ON Product Technical Specification Introduction In addition to the interfaces above, the AirPrime HL6528-G and HL6528-G2.8V modules also provide the following interfaces and peripheral connectivity:
GPS Antenna External LNA Enable/Disable Pulse Per Second 1.8. Connection Interface The AirPrime HL6528x module is an LGA form factor device. All electrical and mechanical connections are made through the 146 pads Land Grid Array (LGA) on the bottom side PCB. Figure 2. AirPrime HL6528x Module Mechanical Overview The 146 pads have the following distribution 66 inner signal pads, 1x0.5mm, pitch 0.8mm 1 reference test point (Ground), 1.0mm diameter 7 test point (JTAG), 0.8mm diameter, 1.20mm pitch 64 inner ground pads, 1.0x1.0mm, pitch 1.825mm/1.475mm 4 inner corner ground pads, 1x1mm 4 outer corner ground pads, 1x0.9mm 1.9. ESD According to IEC61000-4-2 model, the AirPrime HL6528x module can stand for:
+/-2kV ESD on all the LGA pins
+/-8kV ESD on RF pins 4114016 Rev 3.0 January 28, 2014 14 Product Technical Specification Introduction 1.10. Environmental and Certifications 1.10.1. Environmental Specifications The environmental specification for both operating and storage conditions are defined in the table below. Table 4. AirPrime HL6528x Module Environmental Specifications Conditions Range Operating Class A
-30C to +70C Operating Class B
-40C to +85C Storage
-40C to +90C Class A is defined as the operating temperature ranges that the device:
Shall exhibit normal function during and after environmental exposure. Shall meet the minimum requirements of 3GPP or appropriate wireless standards. Class B is defined as the operating temperature ranges that the device:
Shall remain fully functional during and after environmental exposure Shall exhibit the ability to establish a voice, SMS or DATA call (emergency call) at all times even when one or more environmental constraint exceeds the specified tolerance. Unless otherwise stated, full performance should return to normal after the excessive constraint(s) have been removed. 1.10.2. Regulatory The AirPrime HL6528x module is compliant with the following regulations: R&TTE directive, GCF-CC, CE marking, FCC, and PTCRB. Table 5. Regulation Compliance Document Current Version Title NAPRD.03 GCF-CC TS 51.010-1 v5.10
(2012-01) Overview of PCS Type certification review board (PTCRB) Mobile Equipment Type Certification and IMEI control v3.45.1
(2012-03) V10.0.0
(2012-03) GCF Conformance Certification Criteria 3rd Generation Partnership Project; Technical Specification Group GSM/EDGE Radio Access Network; Digital cellular telecommunications system (Phase 2+);
Mobile Station (MS) conformance specification; Part 1: Conformance specification TS 51.010-2 V10.0.0
(2012-03) 3rd Generation Partnership Project; Technical Specification Group GSM/EDGE Radio Access Network; Mobile Station (MS) conformance specification; Part 2:
Protocol Implementation Conformance Statement (PICS) proforma specification 4114016 Rev 3.0 January 28, 2014 15 Product Technical Specification Introduction Document Current Version Title Global System for Mobile Communications (GSM); Harmonized EN for Mobile Stations in the GSM 900 and GSM 1800 Bands Covering Essential Requirements Under Article 3.2 of the R&TTE Directive (1999/5/EC) Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 KHz and 40 GHz Electromagnetic Compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 7: Specific Conditions for Mobile and Portable Radio and Ancillary Equipment of Digital Cellular Radio Telecommunications Systems (GSM and DCS) IEC 60950-1:2005/A1:2009 EN 60950-1:2006/A11:2009/A1:2010/A12:2011 Information technology equipment safety- and general requirements Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range;
Part 1: Technical characteristics and test methods Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range;
Part 2: Harmonized EN under article 3.2 of the R&TTE Directive Subpart B - Radio frequency devices subpart B Unintentional Radiators Cellular Radiotelephone Service; Subpart H: Cellular Radiotelephone Service Personal Communications Service; Subpart E: Broadband PCS. Cellular telephones employing new technologies operating in the 824-849 MHz and 869-894 MHz bands. 2 GHz personal communications services Requirements for connection to an air interface of a telecommunications network Part 1; General Requirements for connection to an air interface of a Telecommunications Network - Part 3: GSM Customer Equipment EN 301511 EN 301489-1 V9.0.2
(2003-03) V1.9.2
(2011-09) EN 301489-3 V1.4.1
(2002-08) EN 301489-7 V1.3.1
(2005-11) EN 60950-1 NA EN 300440-1 EN 300440-2 v1.6.1
(2012-08) V1.4.1
(2012-08) FCC Part 15B FCC Part 22H FCC Part 24E NA NA NA Issue 2:2005 Issue 5:2009 2008 2005 RSS-132 RSS-133 AS/ACIF S042.1 AS/ACIF S042.3 AS/NZS 60950.1 SRRC 2011 Safety of information technology equipment (IEC 60950-1, Ed.2.0: 2005, MOD) NA State Radio Regulation Center - China Type Approval 4114016 Rev 3.0 January 28, 2014 16 Product Technical Specification Introduction 1.10.3. RoHS Directive Compliant The AirPrime HL6528x module is compliant with RoHS Directive 2011/65/EU which sets limits for the use of certain restricted hazardous substances. This directive states that from 1st July 2006, new electrical and electronic equipment put on the market does not contain lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). 1.10.4. Disposing of the Product This electronic product is subject to the EU Directive 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE). As such, this product must not be disposed of at a municipal waste collection point. Please refer to local regulations for directions on how to dispose of this product in an environmental friendly manner. 1.10.5. References
[1] AirPrime HL Series Customer Process Guidelines Reference Number: 4114330
[2] AirPrime HL6 and HL8 Series AT Commands Interface Guide Reference Number: 4114680 4114016 Rev 3.0 January 28, 2014 17 2. Pad Definition AirPrime HL6528x module pins are divided into 3 functional categories. Core functions and associated pins cover all the mandatory features for M2M connectivity and will be available by default across all CF3 family of modules. These Core functions are always available and always at the same physical pin locations. A customer platform using only these functions and associated pins is guaranteed to be forward and/or backward compatible with the next generation of CF3 modules. Extension functions and associated pins bring additional capabilities to the customer. Whenever an Extension function is available on a module, it is always at the same pin location. Custom functions and associated pins are specific to a given module, and make an opportunistic use of specific chipset functions and I/Os. Custom features should be used with caution as there is no guarantee that the custom functions available on a given module will be available on other CF3 modules. Other pins marked as not connected or reserved should not be used. Table 6. Pad Description Pin # Signal Name Function 1 2 3 4 5 6 7 8 GPIO1/I2C1_CLK UART1_RI UART1_RTS UART1_CTS UART1_TX UART1_RX UART1_DTR UART1_DCD General purpose input/output/I2C Clock UART1: Ring indicator UART1: Request to send UART1: Clear to send UART1: Transmit data UART1: Receive data UART1: Data terminal ready UART1: Data carrier detect Active Low/ High IO Voltage Domain for HL6528 and HL6528-G IO Voltage Domain for HL6528-2.8V and HL6528-
G2.8V Recommendation for Unused Pins Type L L L L 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V Left Open Extension Left Open Connect to UART1_CTS Connect to UART1_RTS Mandatory connection Mandatory connection Connect to UART1_DSR Left Open Core Core Core Core Core Core Core I/O I/O O I O I O I O 4114016 Rev 3.0 January 28, 2014 18 Product Technical Specification Pin # Signal Name Function UART1_DSR UART1: Data set ready GPIO2/UIM2_VCC_CT RL General purpose input/output (
UIM2 VCC Control RESET_IN Input reset signal Active Low/ High IO Voltage Domain for HL6528 and HL6528-G IO Voltage Domain for HL6528-2.8V and HL6528-
G2.8V L L L 1.8V 1.8V 1.8V 2.8V 2.8V 2.8V 2.8V 3.0V 1.8V 2.8V 2.8V 1.8V/3V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 3.0V 2.8V 2.8V 2.8V 1.8V/3V Pad Definition Recommendation for Unused Pins Type Connect to UART1_DTR Core Left Open Left Open (Test point recommended) Left Open Left Open Left Open Left Open C=10F Core Core Not Connected Not Connected Not Connected Not Connected Not Connected Extension Extension Extension Extension Extension Mandatory Left Open Custom Connected to Ground Connected to Ground Mandatory connection Not Connected Extension Extension Core I/O O I/O I O O I I Not Connected Not Connected Not Connected Not Connected Not Connected Speaker negative output
(32 impedance) Speaker positive output
(32 impedance) Microphone positive input Microphone negative input I/O Power supply for RTC backup Factory use only Not Connected I Analog to digital conversion I Analog to digital conversion 1.8V/3V UIM1 Power supply O I 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 NC NC NC NC NC SPKR_N SPKR_P MIC_P MIC_N BAT_RTC TP2 NC ADC1 ADC0 UIM1_VCC 4114016 Rev 3.0 January 28, 2014 19 Product Technical Specification Pad Definition Pin # Signal Name Function 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 UIM1_CLK UIM1_DATA UIM1_RESET NC NC NC PCM_OUT PCM_IN PCM_SYNC PCM_CLK GND RF_GPS*
GND GPIO7 GPIO8 PPS*
EXT_LNA_GPS_EN*
SPI1_SRDY VGPIO 1.8V/3V UIM1 Clock 1.8V/3V UIM1 Data 1.8V/3V UIM1 Reset NC (Reserved for 3G compatibility) NC (Reserved for 3G compatibility) NC (Reserved for 3G compatibility) PCM data out PCM data in PCM sync out PCM clock Ground RF GPS Input Ground General purpose input/output General purpose input/output GPS Pulse Per Second External GPS LNA enable Debug use only SPI Slave Ready GPIO voltage output I/O O I/O O O I I/O I/O GND I GND I/O I/O O O I O Active Low/ High IO Voltage Domain for HL6528 and HL6528-G IO Voltage Domain for HL6528-2.8V and HL6528-
G2.8V Recommendation for Unused Pins Type L H 1.8V/3V 1.8V/3V 1.8V/3V 1.8V/3V 1.8V/3V 1.8V/3V Mandatory connection Mandatory connection Mandatory connection Core Core Core 2.8V 2.8V 2.8V 2.8V 0V 0V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 2.8V 2.8V 2.8V 2.8V 0V 0V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V Left Open Left Open Left Open Left Open Mandatory connection Mandatory connection Mandatory connection Left Open Left Open Left Open Left Open Left Open (Test point mandatory) Left Open Not Connected Not Connected Not Connected Extension Extension Extension Extension Core Extension Core Core Core Extension Extension Extension Core 4114016 Rev 3.0 January 28, 2014 20 Product Technical Specification Pin # Signal Name Function I/O Active Low/ High IO Voltage Domain for HL6528 and HL6528-G IO Voltage Domain for HL6528-2.8V and HL6528-
G2.8V Recommendation for Unused Pins Type Pad Definition 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 GPIO6 TP1 GND RF_MAIN GND SPI1_MRDY SPI1_MISO SPI1_CLK SPI1_MOSI UIM2_VCC UIM2_DATA General purpose input/output Test Point 1 0- JTAG Enable Open-Normal Mode Ground RF GSM Input/output Ground Debug use only SPI Master Ready Debug use only SPI Master In Slave Out Debug use only SPI Clock Debug use only SPI Master Out Slave In UIM2 Power supply UIM2 Data UIM2_RESET/BUZZER UIM2 Reset/Buzzer UIM2_CLK/PWM UIM2 Clock/PWM PWR_ON 2G_TX_ON VBATT_PA Active Low Power On control signal 2G TX burst indicator 3.7V Power Amplifier Power supply I/O I GND I/O GND O I O O O I/O O O I/O O I L L H 1.8V 1.8V 0V 0V 1.8V 1.8V 1.8V 1.8V 2.8V 2.8V 2.8V 2.8V 3.0V 2.8V 3.7V 2.8V 2.8V 0V 0V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 3.0V 2.8V 3.7V Left Open Core Left Open Extension Mandatory connection Mandatory connection Mandatory connection Left Open (Test point mandatory) Left Open (Test point mandatory) Left Open (Test point mandatory) Left Open (Test point mandatory) Left Open Left Open Left Open Left Open Core Core Core Extension Extension Extension Extension Extension Extension Extension Extension Mandatory connection Core Left Open Extension Mandatory connection Core 4114016 Rev 3.0 January 28, 2014 21 Product Technical Specification Pin # Signal Name Function I/O Active Low/ High IO Voltage Domain for HL6528 and HL6528-G IO Voltage Domain for HL6528-2.8V and HL6528-
G2.8V Recommendation for Unused Pins Type Pad Definition 62 63 64 65 66 VBATT_PA VBATT UIM1_DET/GPIO3 UIM2_DET/GPIO4 GPIO5/I2C1_DATA 67-70 GND 3.7V Power Amplifier Power supply 3.7V Power supply I I UIM1 Detection/General purpose input/output UIM2 Detection/General purpose input/output General purpose input/output/IC DATA Ground I/O I/O I/O GND H H 71-
166 167-
234 235 236 237 238 239 240 241 242 Note:
These pins are not available on the AirPrime HL6548x modules GND GND TEST_PIN JTAG_RESET JTAG_TCK JTAG_TDO JTAG_TMS JTAG_TRST JTAG_TDI JTAG_RTCK Ground (Test Point) JTAG RESET JTAG Test Clock JTAG Test Data Output JTAG Test Mode Select JTAG Test Reset JTAG Test Data Input JTAG Returned Test Clock GND GND I I O I I I O L L
*
This pin is only available on the HL6528-G and H6528-G2.8V. 3.7V 3.7V 1.8V 1.8V 1.8V 0V 0V 0V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V 3.7V 3.7V 2.8V 2.8V 2.8V 0V 0V 0V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V Mandatory connection Mandatory connection Left Open Left Open Left Open Core Core Core Extension Extension Mandatory connection Core Mandatory connection Core Left Open Left Open Left Open Left Open Left Open Left Open Left Open Left Open Not connected Extension Extension Extension Extension Extension Extension Extension 4114016 Rev 3.0 January 28, 2014 22 Product Technical Specification 2.1.1. Pin Configuration (Top View) Pad Definition Figure 3. Pin Configuration 4114016 Rev 3.0 January 28, 2014 23 16816916717018171615141312111098764321566656463626160593435363738394041424344454648495051475857565553525470671920212223242526272829303233316968192193194195196197198171191214215216217218199172190213228229230219200173189212227234231220201174188211226233232221202175187210225224223222203176186209208207206205204177185184183182181180179178235236237238239240241242GNDGPIO5/I2C1_DATAUIM2_DET/GPIO4UIM1_DET/GPIO3VBATTVBATT_PAVBATT_PA2G_TX_ONPWR_ONUIM2_CLK/PWMUIM2_RESET/BUZZERUIM2_DATAUIM2_VCCSPI1_MOSISPI1_CLKSPI1_MISOGNDGNDMIC_PMIC_NBAT_RTCRESERVEDNCADC1ADC0UIM1_VCCUIM1_CLKUIM1_DATAUIM1_RESETNCNCNCPCM_OUTGNDPCM_INPCM_SYNCPCM_CLKGNDRF_GPSGNDGPIO7GPIO8PPSEXT_LNA_GPS_ENSPI1_SRDYVGPIOGPIO6TP1GNDRF_MAINGNDSPI1_MRDYSPKR_PSPKR_NNCNCNCNCNCRESET_INGPIO2UART1_DSRUART1_DCDUART1_DTRUART1_RXUART1_TXUART1_CTSUART1_RTSUART1_RIGPIO1/I2C1_CLKJTAG_RTCKJTAG_TDIJTAG_TRSTJTAG_TMSJTAG_TDOJTAG_TCKJTAG_RESETTEST POINTCore pinExtension pinCustom pin 3. Note:
Detailed Interface Specifications If not specified, all electrical values are given for VBATT=3.7V and an operating temperature of 25C. For standard applications, VBATT and VBATT_PA must be tied externally to the same power supply. For some specific applications, AirPrime HL6528x module supports separate VBATT and VBATT_PA connection if requirements below are fulfilled. 3.1. Power Supply The AirPrime HL6528x module is supplied through the VBATT signal with the following characteristics. Table 7. Power Supply VBATT voltage (V) VBATT_PA voltage (V) Full Specification VBATT_PA voltage (V) Extended Range2 Minimum Typical Maximum 3.21 3.01 2.82 3.7 3.7 3.7 4.5 4.5 4.5 1 2 This value has to be guaranteed during the burst No guarantee of 3GPP performances over extended range 3.2. Current Consumption The following table lists the current consumption of the AirPrime HL6528x module at different conditions. Note:
Typical values are defined for VBATT/VBATT_PA at 3.7V, for a 50ohms impedance at all RF ports. Max values are provided for a VSWR 3:1. Table 8. Current Consumption Parameters Min. Typ. Max. Off mode (HL6528 and HL6528-2.8V) (A) Off mode (HL6528-G and HL6528-G2.8V) (A) GSM Sleep mode (mA) Single UIM operation GSM Sleep mode (mA) Dual UIM operation DRX2 DRX5 DRX9 DRX2 DRX5 DRX9 GSM in communication mode (mA) GSM900 / GSM850
(PCL=5) TBD TBD 1.3 0.9 0.8 3.0 1.8 1.5 TBD GPRS (2 TX, 3 RX) (mA) DCS / PCS (PCL=0) TBD GSM900 / GSM850
(PCL=5) TBD DCS / PCS (PCL=0) TBD 40 40 1.4 1.1 1.0 3.1 2.0 1.7 220 160 380 270 TBD TBD 2.5 2.2 2.0 4.5 3.1 2.6 TBD TBD TBD TBD 4114016 Rev 3.0 January 28, 2014 24 Product Technical Specification Detailed Interface Specifications Parameters Min. Typ. Max. Peak Current consumption (A) GNSS Acquisition1 (mA) GSM registered on network GNSS Navigation (1Hz)1 (mA) GSM registered on network GNSS Navigation (1Hz)1 (mA) GSM in Flight mode GNSS Hibernate mode2 (mA) GSM registered on network GSM900 / GSM850 DCS / PCS Max value3 Min value4 Max value3 Min value4 Max value3 Min value4 Max value3 Min value4 TBD TBD 43 TBD 39 TBD TBD TBD 18 TBD 1.50 0.90 51 28 45 25 20 1.5 TBD TBD 64 TBD 57 TBD TBD TBD 26 TBD 1 Maximum SVs in view, signal level @-130dBm, high gain configuration 2 Hot start conditions are maintained in Hibernate mode3 Baseband is running (or no sleep mode allowed) in max value condition. Refer to document [2] AirPrime HL6 and HL8 Series AT Commands Interface Guide for sleep mode description. Baseband is in sleep mode in min value condition. Refer to document [2] AirPrime HL6 and HL8 Series AT Commands Interface Guide for sleep mode description. 4 Table 9. Current Consumption per power supply VBATT / VBATT_PA Parameters Min. Typ. Max. VBATT_PA VBATT
(HL6528 and HL6528-2.8V) VBATT
(HL6528-G and HL6528-G2.8V) Peak current (A) GSM communication mode, 2TX Peak current (A) GSM communication mode, 1TX Average current (mA) GSM communication mode, 1TX Peak current (A) GSM communication mode, 2TX Peak current (A) GSM communication mode, 1TX Average current (mA) GSM communication mode, 1TX Peak current (A) GSM communication mode, 2TX GNSS Navigation mode Peak current (A) GSM communication mode, 1TX GNSS Navigation mode GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) 1.30 0.80 150 90 290 125 70 70 4114016 Rev 3.0 January 28, 2014 25 Product Technical Specification Detailed Interface Specifications Parameters Min. Typ. Max. Average current (mA) GSM communication mode, 1TX GNSS Navigation mode GSM900 / GSM850 (PCL=5) DCS / PCS (PCL=0) 3.3. VGPIO The VGPIO output can be used to:
Pull-up signals such as I/Os Supply the digital transistors driving LEDs Act as a voltage reference for the ADC interfaces, ADC0 and ADC1 The VGPIO output is available when the AirPrime HL6528x module is switched ON. Table 10. VGPIO Electrical Characteristics Parameter HL6528, HL6528G HL6528-2.8V, HL6528-G2.8V Min Typ Max Min Typ Max Voltage level (V) 1.70 1.80 1.90 2.65 2.80 2.95 Current capability active mode (mA) Current capability sleep mode (mA) Line regulation
(mV/V) Rise Time(ns)
-
-
-
-
50 3 50 6
-
-
-
-
-
-
-
-
-
-
-
-
50 3 50 6 Remarks Both active mode and sleep mode 32KHz system clock enable Iout = MAX Test load capacitor =
30 pF 4114016 Rev 3.0 January 28, 2014 26 Product Technical Specification Detailed Interface Specifications 3.4. BAT_RTC The AirPrime HL6528x module provides an input/output to connect a Real Time Clock power supply. This pin is used as a back-up power supply for the internal Real Time Clock. The RTC is supported when VBATT is available but a back-up power supply is needed to save date and hour when VBATT is switched off. If VBATT is available, the back-up battery can be charged by the internal 3.0V power supply regulator. Table 11. BAT_RTC Electrical Characteristics Parameter Input voltage (V) Input current consumption (A) Output voltage (V) Max charging current (@VBATT=3.6V) (mA) 3.5. UIM Interface Minimum Typical Maximum
-
-
2.82
-
3.0 2.5 3.0 0.6
-
-
3.18
-
The AirPrime HL6528x module has two physical UIM interfaces one main UIM interface (UIM1), and a second UIM interface (UIM2) reserved for Dual UIM Dual Standby option. 3.5.1. UIM1 Interface The UIM1 interface allows control of a 1.8V/3V UIM and is fully compliant with GSM 11.11 recommendations related to UIM functions. The five signals used by this interface are as follows:
UIM1_VCC: power supply UIM1_CLK: clock UIM1_IO: I/O port UIM1_RST: reset UIM1_DET: UIM detection (optional) Table 12. Electrical Characteristics of UIM1 Parameter Minimum Typical Maximum Remarks UIM1 Interface Voltage (V)
(VCC,CLK,IO,RST) UIM1_VCC Current (mA) UIM1_VCC Line Regulation (mV/V) UIM1_VCC Power-up Setting Time
(us) from power down 2.7 1.65
-
-
-
3.0 1.80
-
-
10 3.15 1.95 10 50
-
The appropriate output voltage is auto detected and selected by software. Max output current in sleep mode = 3 mA At Iout_Max 4114016 Rev 3.0 January 28, 2014 27 Product Technical Specification Detailed Interface Specifications 3.5.1.1. UIM1_DET UIM1_DET is used to detect and notify the application about the insertion and removal of a UIM device in the UIM socket connected to the main UIM interface (UIM1). When a UIM is inserted, the state of UIM1_DET transitions from logic 0 to logic 1. Inversely, when a UIM is removed, the state of UIM1_DET transitions from logic 1 to logic 0. The GPIO for UIM1_DET is GPIO3.. 3.5.2. UIM2 Interface The UIM2 interface is optional and only intended to be used with Dual UIM Dual Standby feature. Note:
This is the preferred interface for when MFF2 UIM cards are used. The five signals used by this interface are as follows:
UIM2_VCC: power supply UIM2_CLK: clock UIM2_IO: I/O port UIM2_RST: reset UIM2_DET: HW detection (optional) UIM2_VCC_CTRL: control signal for external analog switch (mandatory) Table 13. Electrical Characteristics of UIM2 Parameter Minimum Typical Maximum Remarks UIM2 Interface Voltage (V)
(VCC, CLK, IO, RST) UIM2 Interface Voltage (V)
(VCC_CTRL) UIM2_VCC Current (mA) 2.7 2.85 3.0
-
1.8 or 2.8
-
10 UIM2_VCC_CTRL is on VGPIO power domain Max output current in sleep mode = 3 mA Note:
The UIM2 interface is fixed at 3V; do not use a direct connection with a 1.8V-only UIM card. 3.5.2.1. UIM2_DET UIM2_DET is used to detect and notify the application about the insertion and removal of a UIM device in the UIM socket connected to the second UIM interface (UIM2). When a UIM is inserted, the state of UIM2_DET transitions from logic 0 to logic 1. Inversely, when a UIM is removed, the state of UIM2_DET transitions from logic 1 to logic 0. The GPIO for UIM2_DET is GPIO4.. 3.5.2.2. UIM2_VCC_CTRL An analog switch must be added on the customer board when using the UIM2 interface. This analog switch is controlled by GPIO2. 4114016 Rev 3.0 January 28, 2014 28 Product Technical Specification Detailed Interface Specifications Table 14. UIM2_VCC_CTRL Analog Switch Truth Table GPIO2 (UIM2_VCC_CTRL) Function Low High UIM2_VCC connected to UIM2_VCC UIM2_VCC disconnected from UIM2_VCC Figure 4. UIM2 with an Analog Switch 3.6. Electrical Information for Digital I/O The table below enumerates the electrical characteristics of the following digital interfaces:
UART PCM GPIOs IC SPI RESET JTAG Depending on the AirPrime HL6528x module variant, digital IOs are either 2.8V or 1.8V power domain. Note:
The PCM interface only supports 2.8V even with 1.8V configuration. Table 15. Digital I/O Electrical Characteristics Parameter HL6528, HL6528G HL6528-2.8V, HL6528-G2.8V Min Typ Max Min Typ Max Input Current-High(A)
-10 Input Current-Low(A)
-10 DC Output Current-
High(mA)*
-
-
-
-
10 10 15
-10
-10
-
-
-
-
10 10 15 Remarks Pin driving a "1" with output set at "0"
4114016 Rev 3.0 January 28, 2014 29 HL6528xSIM2 CardAnalogSwitch GPIO2 (UIM2_VCC_CTRL)UIM2_VCCUIM2_RESETUIM2_CLKUIM2_DATASIM2_VCCSIM2_RSTSIM2_CLKSIM2_DATAUIM2_DET (GPIO)SIM2_DET Product Technical Specification Detailed Interface Specifications Parameter HL6528, HL6528G HL6528-2.8V, HL6528-G2.8V Min Typ Max Min Typ Max DC Output Current-
Low(mA)*
-15 Input Voltage-High(V) 1.4 Input Voltage-Low(V)
-0.2 Output Voltage-High(V) 1.7 Output Voltage-Low(V) 0
-
-
-
-
-
2.2 0.4 1.9 0.1
-15 2.4
-0.2 2.7 0
-
-
-
-
-
3.2 0.4 2.95 0.1 Remarks Pin driving a "0" with output set at "1"
*
The maximum current for one GPIO is 15mA, but all GPIOs cant provide 15mA at a time since the VIO is limited to 50mA 3.7. Main Serial Link (UART1) The main serial link (UART1) is used for communication between the AirPrime HL6528x module and a PC or host processor. It consists of a flexible 8-wire serial interface that complies with RS-232 interface. The supported baud rates of the UART1 are 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200 bit/s, with autobauding and up to 1Mbit/s at maximum baud rate. The signals used by UART1 are as follows:
TX data (UART1_TX) RX data (UART1_RX) Request To Send (UART1_RTS) Clear To Send (UART1_CTS) Data Terminal Ready (UART1_DTR) Data Set Ready (UART1_DSR) Data Carrier Detect (UART1_DCD) Ring Indicator (UART1_RI) UART1 pin description is summarized below. Table 16. UART1 Pin Description Signal Name (Module side) I/O (Module side) Description UART1_DTR I (active low) UART1_DCD UART1_RX UART1_RTS UART1_TX UART1_CTS UART1_RI UART1_DSR O O I I O O O Prevents the AirPrime HL6528x from entering sleep mode, switches between data mode and command mode, and wakes the module up. Signal data connection in progress Receive data Wakes the module up when KSLEEP=1 is used Transmit data AirPrime HL6528x is ready to receive AT commands Signal incoming calls (voice and data), SMS, etc. Signal UART interface is ON 4114016 Rev 3.0 January 28, 2014 30 Product Technical Specification Detailed Interface Specifications 3.8. Power On Signal (PWR_ON) A low level signal has to be provided to switch the AirPrime HL6528x module ON. It is internally connected to the permanent 3.0V supply regulator inside the HL6528x via a pull-up resistor. Once VBATT is supplied to the HL6528x module, this 3.0V supply regulator will be enabled and so PWR_ON signal is by default at high level. The PWR_ON signals characteristics are listed in the table below. Table 17. PWR_ON Electrical Characteristics Parameter Minimum Typical Maximum Input Voltage-Low (V) Input Voltage-High (V) 2.4 Power-up period (ms) from PWR_ON falling edge 2000
-
-
-
0.4 3.3
-
Note:
As PWR_ON is internally pulled up, a simple open collector or open drain transistor must be used for ignition. The PWR_ON signal will become low after the module is ready. It cannot be directly driven by a GPIO signal. VGPIO is an output from the module that can be used to check if the module is active. When VGPIO = 0V the module is OFF. When VGPIO = 2.8V or 1.8V the module is ON (it can be in Idle, Communication or Sleep mode) After a few seconds, the UART1_CTS enters active state and the module is ready to receive AT commands. Figure 5. PWR_ON Sequence Note:
PWR_ON cannot be used to power the module off. The module is powered off with AT command AT*PSCPOF. 4114016 Rev 3.0 January 28, 2014 31 Product Technical Specification Detailed Interface Specifications 3.9. Reset Signal (RESET) To reset the module, a low level pulse must be sent on RESET pin for at least 10ms. This action will immediately restart the AirPrime HL6528x module. It is therefore useless to perform a new ignition sequence (PWR_ON) afterwards. As RESET is internally pulled up, a simple open collector or open drain transistor can be used to control it. The RESET signal will reset the registers of the CPU and reset the RAM memory as well. Note:
As RESET is referenced to the VGPIO domain (internally to the module) it is impossible to reset before the module starts or to try to use the RESET as a way to start the module. Parameter HL6528, HL6528G HL6528-2.8V, HL6528-G2.8V Min Typ Max Min Typ Max Input Voltage-Low (V) Input Voltage-High (V) Power up Period (ms) from RESET falling edge 1.4 38
-
-
-
0.4
-
2.4 38
-
-
-
0.4
-
3.10. ADC Two Analog to Digital Converter input, ADC0 and ADC1 are provided by the AirPrime HL6528x module. These converters are 10-bit resolution ADCs ranging from 0 to 3V. Typically, the ADCx input can be used to monitor external temperature. This is very useful for monitoring the application temperature and can be used as an indicator to safely power OFF the application in case of overheating (for Li-Ion batteries). Both ADCs have the characteristics listed in the table below. Table 18. ADC Electrical Characteristics Parameter Minimum Typical Maximum Remarks ADC Resolution (bits) Input Voltage Range (V) Update rate per channel (KHz) Differential Nonlinearity (bits) Integral Nonlinearity (bits) Offset Error (mV) Gain Error (mV/LSB) Input Resistance (k) Input Capacitance (pF)
-
0
-
-1
-2.5
-
-
120
-
10
-
-
-
-
5 0.02 150
-
-
3 200
+3
+2.5
-
-
-
10 General purpose input LSB 3.11. Analog Audio Interfaces The AirPrime HL6528x module supports one differential microphone input and one differential speaker output. It also includes a noise suppression and echo cancellation feature which allows for an enhanced voice call quality. 4114016 Rev 3.0 January 28, 2014 32 Product Technical Specification Detailed Interface Specifications 3.11.1. Analog Audio Input The microphone input can either have a single-ended or a differential connection. However, performance with common mode noise and TDMA noise varies depending on the connection mode and PCB layout. When connecting a microphone to the AirPrime HL6528x module, ensure to have a very good ground plane, very good filtering as well as shielding in order to avoid any disturbance on the audio path. The gain of the microphone input can be tuned using AT commands. The AirPrime HL6528x module microphone pins already include suitable biasing for an electret microphone. The electret microphone can then be connected directly on the inputs for easy connection. AC coupling is also already embedded in the HL6528x embedded module. Table 19. Analog Audio Interface Input Parameter Minimum Typical Maximum Test Conditions MIC_P DC Biasing (V) MIC_N DC Biasing (V) Maximum input range (V) Nominal reference level (mVrms) Input Micro amplifier gain (dB)
-6 2.4 0 1.4 16 Through internal 2.2k Through internal 2.2k Gain = - 6dB Gain = + 34dB
+ 50 Note:
It is recommended to add ESD protection to the microphone when it is exposed to the external environment. The ESD protection should be connected between the audio lines and a good ground, and placed as close to the microphone as possible. 3.11.2. Analog Audio Outputs Table 20. Analog Audio Interface Output Parameter Min Typ Max Test Conditions Maximum output range (Vrms) Load resistance () Output amplifier gain (dB)
-28 1.65 32
-
8 Load=32, THD=1%, Output gain = 8 dB Note:
It is recommended to add ESD protection to the speaker when it is exposed to the external environment. The ESD protection should be connected between the audio lines and a good ground, and placed as close to the speaker as possible. Its important to select an appropriate speaker. The following enumerates the recommended speaker characteristics. Table 21. Recommended Speaker Characteristics Characteristic Value Input power: rated / max 0.1W (Rate) Audio chain impedance 32 +/- 10% at 1V 1KHz Frequency Range 300 Hz ~ 4.0 KHz 4114016 Rev 3.0 January 28, 2014 33 Product Technical Specification Detailed Interface Specifications Characteristic Value Sensitivity (S.P.L)
>105 dB at 1KHz with IEC318 coupler Distortion 5% max at 1K Hz, nominal input power 3.12. PCM The Digital Audio Interface (PCM) interface allows connectivity with standard audio peripherals. It can be used, for example, to connect an external audio codec. The programmability of this interface allows addressing a large range of audio peripherals. The signals used by the Digital Audio Interface are as follows:
PCM_SYNC: The frame synchronization signal delivers an 8KHz frequency pulse that synchronizes the frame data in and the frame data out (short frame synchronization only). PCM_CLK: The frame bit clock signal controls data transfer with the audio peripheral. PCM_OUT: The frame data out relies on the selected configuration mode. PCM_IN: The frame data in relies on the selected configuration mode. The PCM interface is a high speed full duplex interface that can be used to send and receive digital audio data to external audio ICs. The digital audio interface also features the following:
PCM master or slave mode 8 bits or 16 bits data word length MSB or LSB first Rising or falling sampling clock edge Configurable PCM bit clock rate up to 1MHz Refer to the following table for the electrical characteristics of the digital audio interface. Table 22. Digital Audio Interface Electrical Characteristics Signal Description Minimum Typical Maximum Tsync_low + Tsync_high PCM-SYNC period (s) Tsync_low Tsync_high TSYNC-CLK TCLK-cycle TIN-setup TIN-hold TOUT-delay TSYNC-delay PCM-SYNC low time (s) PCM-SYNC high time (s) PCM-SYNC to PCM-CLK time (ns) PCM-CLK period (ns) PCM-IN setup time (ns) PCM-IN hold time (ns) PCM-OUT delay time (ns) PCM-SYNC output delay (ns) The following figure shows the PCM timing waveform. 50 50
-11 125 124 1 651 1302 20 9 4114016 Rev 3.0 January 28, 2014 34 Product Technical Specification Detailed Interface Specifications Figure 6. PCM Timing Waveform 3.13. I2C Interface NMEA frames can be output from the UART or through a dedicated serial port (I2C). Table 23. I2C Pin Description Pad #
Name Function 1 66 I2C1_CLK I2C1_DATA I2C Serial Clock Line I2C Serial Data Line Note:
I2C pins are multiplexed with GPIO features. The main characteristics of the I2C interface are as follows:
Master mode (I2C1_CLK is an output of the AirPrime HL6528x module) I2C clock is set at 400KHz As AirPrime HL6528x module is master only, devices connected to the I2C bus shall be slave devices. In order for AirPrime HL6528x module to communicate with the slave device, the slave 7-bit address shall be loaded inside the module before activating the GPS NMEA output. See [2] for AT command description. 3.14. Debug Interfaces The AirPrime HL6528x module provides two interfaces for a powerful debug system. 3.14.1. SW Traces The AirPrime HL6528x module provides a SW TRACE interface, providing real-time instruction and data trace of the modem core. The SW TRACE interface is accessible through the SPI port. 4114016 Rev 3.0 January 28, 2014 35 Detailed Interface Specifications Product Technical Specification Table 24. SPI Pin Description Pad #
Name Function 44 51 52 53 54 SPI1_SRDY SPI1_MRDY SPI1_MISO SPI1_CLK SPI1_MOSI SPI Slave Ready SPI Master Ready SPI Master In Slave Out SPI Clock SPI Master Out Slave In Note:
It is strongly recommended to provide access through Test Points to this interface. 3.14.2. JTAG The JTAG interface provides debug access to the core of the AirPrime HL6528x module. These JTAG signals are accessible through solderable Test Points. Table 25. JTAG Pin Description Pad #
Name Function 47 236 237 238 239 240 241 242 TP1 JTAG_RESET JTAG_TCK JTAG_TDO JTAG_TMS JTAG_TRST JTAG_TDI JTAG_RTCK Test Point 1 JTAG RESET JTAG Test Clock JTAG Test Data Output JTAG Test Mode Select JTAG Test Reset JTAG Test Data Input JTAG Returned Test Clock Note:
Its recommended to provide access through Test Points to the JTAG interface pins (for failure analysis and HL6528x debugging). All signals listed in the table above shall be outputs on the customer board to allow JTAG debugging. 3.15. PPS (HL6528-G and HL6528-G2.8V only) The PPS signal is an output pulse related to GPS receiver time. Table 26. PPS Electrical Characteristics Parameter Minimum Typical Maximum Conditions HL6528-G HL6528-G2.8V Voltage Level (V) Frequency (Hz) Pulse width (ms) Synchronization to GPS time (s) 1.70 2.65 1.80 2.8 1 250 1.90 2.95 1 Note:
This output is available only when GNSS is in tracking mode. 4114016 Rev 3.0 January 28, 2014 36 Product Technical Specification Detailed Interface Specifications 3.16. EXT_LNA_GPS_EN (HL6528-G and HL6528-
G2.8V only) EXT_LNA_GPS_EN ON indicates whether the GNSS receiver is active and can be used to enable an external LNA (or active antenna), especially during GNSS low power mode. Table 27. EXT_LNA_GPS_EN Electrical Characteristics Parameter Minimum Typical Maximum Conditions Voltage Level (V) HL6528-G HL6528-G2.8V 1.70 2.65 1.80 2.8 1.90 2.95 3.17. RF Interface The GSM RF interface of the AirPrime HL6528x module allows the transmission of RF signals. This interface has a 50 nominal impedance. 3.17.1. RF Connection A 50 stripline can be used to connect to standard RF connectors such as SMA, UFL, etc. for antenna connection. Table 28. RF Connection RF Signal Impedance VSWR Rx (max) VSWR Tx (max) RF_MAIN 50 3:1 3:1 3.17.2. RF Performances RF performances are compliant with the ETSI recommendation GSM 05.05. Frequency Band Typical Sensitivity Minimum Sensitivity GSM850 (dBm) EGSM (dBm) DCS (dBm) PCS (dBm)
-109.9
-109.7
-109.5
-108.2
-107
-107
-106
-106 Note:
Values given above are average values across the frequency band. 3.17.3. TX Burst Indicator (2G_TX_ON) The AirPrime HL6528x module provides a signal, 2G_TX_ON, for TX burst indication. 2G_TX_ON is a 2.8V signal and its status depends on the module transmitter state. 4114016 Rev 3.0 January 28, 2014 37 Product Technical Specification Detailed Interface Specifications Refer to the following table for the status of the 2G_TX_ON signal depending on the embedded modules state. Table 29. Burst Indicator States Embedded Module State 2G_TX_ON During TX burst No TX High Low During TX burst, there is a higher current drain from the VBATT_PA power supply which causes a voltage drop. This voltage drop from VBATT_PA is a good indication of a high current drain situation during TX burst. The blinking frequency is about 217Hz. The output logic high duration, Tduration, depends on the number of TX slots and is computed as follows:
T duration = T advance + (0.577ms x number of TX slots) + T delay Table 30. TX Burst Characteristics Parameter Minimum Typical Maximum Output voltage (V) Tadvance (s) Tdelay (s) 2.65 30 0 2.80 180 10 2.95 Figure 7. 2G_TX_ON State during TX Burst 3.18. GNSS Interface The AirPrime HL6528-G and HL6528-G2.8V modules embed an integrated and high-sensitivity Global Navigation Satellite System (GNSS) solution. Based on SiRFstarV from CSR, the AirPrime HL6528-G and HL6528-G2.8V modules combine GPS and GLONASS reception to improve navigation capabilities and position accuracy in obstructed view environments such as urban canyons. GNSS performances are improved by CW jammer and interference mitigation system and automated hardware blanking capabilities. In addition, it supports Downloaded Extended Ephemeris Assisted-GNSS, for enhanced time to acquire or reacquire a fix. The operation of GNSS is offloaded to a GNSS standalone solution to guarantee the availability of modem resources for best performance. 4114016 Rev 3.0 January 28, 2014 38 Product Technical Specification Detailed Interface Specifications The GNSS implementation supports GPS L1 signal (1575.42 20 MHz) and GLONASS L1 FDMA signals for frequency -7 to 6 (1597.5 1605.8 MHz), with 50 connection on the RF_GPS pad. 3.18.1. GNSS Performances Table 31. GNSS Interface Specifications Test Parameters Typical Value Sensitivity GPS Autonomous Acquisition (dBm) Cold and Warm start conditions GPS Autonomous Acquisition (dBm) Hot start conditions GPS Navigation (dBm) GLONASS Navigation (dBm) GNSS Navigation (dBm) GPS Tracking (dBm) GLONASS Tracking (dBm) Autonomous Cold Start Autonomous Warm Start Autonomous Hot Start Aiding Warm Start Time To First Fix (s) 2D Position Error (m) Time To First Fix (s) 2D Position Error (m) Time To First Fix (s) 2D Position Error (m) Time To First Fix (s) 2D Position Error (m) 50%
95%
50%
95%
50%
95%
50%
95%
50%
95%
50%
95%
50%
95%
50%
95%
-147
-159
-161
-158
-161
-165
-165 23.3 34.3 0.86 1.63 19.5 34.4 0.16 0.41 0.7 1 3.8 8.4 TBD TBD TBD TBD Note:
Values in the table above are based on static conditions, RF GNSS level @-130dBm. Cold start does not include internal GNSS firmware download on first GNSS start. 3.18.2. GNSS Antenna Interface Specifications for the GNSS antenna interface are defined in the table below. Table 32. GNSS Antenna Specifications Characteristics Frequency (MHz) GPS L1 GLONASS L1 FDMA GNSS 1575.4220 1597.5-1605.8 4114016 Rev 3.0 January 28, 2014 39 Product Technical Specification Detailed Interface Specifications Characteristics RF Impedance () VSWR max GNSS 50 2:1 The minimum isolation between GNSS and GSM antennas should be 20dB. 3.18.3. GNSS Antenna Recommendations Both passive and active antennas are supported by the AirPrime HL6528-G and HL6528-G2.8V modules. The table below describes the expected performance function as input signal power. Table 33. GNSS Antenna Recommendations GNSS Signal Level Description Input Signal Power (dBm) Expected Performances Absolute maximum Good Acceptable Poor Minimum usable signal Minimum tracking level
-110
>-134
>-147
<-147
-161
-165 Maximum to input level Best performance in TTFF and position accuracy Minimum input level to allow initial acquisition without aiding No signal acquisition without aiding Below this level, no fix with reasonable error Minimum level to lock the signal for fast recovery when the signal returns to the minimum usable level For passive antennas, the internal LNA should be set in high gain mode. For active antennas, the internal LNA gain should be set to low gain if external net gain is higher than 16dB. If the external net gain is lower than 16dB, it is advised to set the internal LNA gain in high gain. In any case, the external net gain should not exceed 24dB. 3.19. GPIO RESET/ DEFAULT states Table 34. Pad Description Pin
#
1 2 3 4 5 6 7 Signal Name Function I/O RESET RESET DEFAULT DEFAULT STATE VALUE STATE VALUE GPIO1/I2C1_C LK UART1_RI General purpose input/output/I2C Clock UART1: Ring indicator O I/O UART1_RTS UART1_CTS UART1_TX UART1_RX UART1_DTR I UART1: Request to send UART1: Clear to send O UART1: Transmit data I UART1: Receive data O UART1: Data terminal ready I 4114016 Rev 3.0 January 28, 2014 40 Product Technical Specification Detailed Interface Specifications Signal Name Function UART1_DCD UART1: Data carrier detect Pin
#
8 9 10 11 12 13 14 15 16 UART1_DSR GPIO2 RESET_IN NC NC NC NC NC 17 SPKR_N 18 SPKR_P 19 MIC_P 20 MIC_N 21 BAT_RTC 22 TP2 23 24 NC ADC1 25 ADC0 26 27 28 29 30 UIM1_VCC UIM1_CLK UIM1_DATA UIM1_RESET NC 31 NC 32 33 34 35 NC PCM_OUT PCM_IN PCM_SYNC I/O O O I/O I O O I I I/O I I I O O I/O O O I I/O RESET RESET DEFAULT DEFAULT STATE VALUE STATE VALUE UART1: Data set ready General purpose input/output Input reset signal Not Connected Not Connected Not Connected Not Connected Not Connected Speaker negative output
(32 impedance) Speaker positive output
(32 impedance) Microphone positive input Microphone negative input Power supply for RTC backup Factory use only 0 JTAGBoundary Scan Mode Open Normal Mode Not Connected Analog to digital conversion Analog to digital conversion 1.8V/3V UIM1 Power supply 1.8V/3V UIM1 Clock 1.8V/3V UIM1 Data 1.8V/3V UIM1 Reset NC (Reserved for 3G compatibility) NC (Reserved for 3G compatibility) NC (Reserved for 3G compatibility) PCM data out PCM data in PCM sync out 4114016 Rev 3.0 January 28, 2014 41 Product Technical Specification Detailed Interface Specifications Pin
#
36 37 38 39 40 41 42 43 44 45 46 Signal Name Function PCM_CLK GND RF_GPS*
GND GPIO7 GPIO8 PPS*
PCM clock Ground RF GPS Input Ground General purpose input/output General purpose input/output GPS Pulse Per Second EXT_LNA_GP S_EN*
External GPS LNA enable SPI1_SRDY VGPIO GPIO6 47 TP1 48 49 50 51 GND RF_MAIN GND SPI1_MRDY 52 SPI1_MISO 53 SPI1_CLK 54 SPI1_MOSI 55 56 57 58 59 60 61 62 63 UIM2_VCC UIM2_DATA UIM2_RESET/
BUZZER UIM2_CLK/PW M PWR_ON 2G_TX_ON VBATT_PA VBATT_PA VBATT Debug use only SPI Slave Ready GPIO voltage output General purpose input/output Test Point 1 0- JTAG Enable Open-Normal Mode Ground RF GSM Input/output Ground Debug use only SPI Master Ready Debug use only SPI Master In Slave Out Debug use only SPI Clock Debug use only SPI Master Out Slave In UIM2 Power supply UIM2 Data UIM2 Reset/Buzzer UIM2 Clock/PWM Active Low Power On control signal 2G TX burst indicator 3.7V Power Amplifier Power supply 3.7V Power Amplifier Power supply 3.7V Power supply I/O I/O GND I GND I/O I/O O O I O I/O I GND I/O GND O I O O O I/O O O I/O O I I I RESET RESET DEFAULT DEFAULT STATE VALUE STATE VALUE 4114016 Rev 3.0 January 28, 2014 42 Product Technical Specification Mechanical Drawings Pin
#
64 65 66 67-
70 Signal Name Function UIM1_DET/GPI O3 UIM2_DET/GPI O4 UIM1 Detection/General purpose input/output UIM2 Detection/General purpose input/output GPIO5/I2C1_D ATA General purpose input/output/IC DATA GND Ground GND 167
-
234 235 TEST_PIN 236 237 JTAG_RESET JTAG_TCK 238 JTAG_TDO 239 JTAG_TMS 240 241 JTAG_TRST JTAG_TDI 242 JTAG_RTCK GND Ground (Test Point) JTAG RESET JTAG Test Clock JTAG Test Data Output JTAG Test Mode Select JTAG Test Reset JTAG Test Data Input JTAG Returned Test Clock I/O I/O I/O I/O GND GND GND I I O I I I O RESET RESET DEFAULT DEFAULT STATE VALUE STATE VALUE 4. Mechanical Drawings Figure 8. AirPrime HL6528x (angular view) 4114016 Rev 3.0 January 28, 2014 43 Product Technical Specification Mechanical Drawings Figure 9. AirPrime HL6528x (side view) Figure 10. AirPrime HL6528x Module (top view) 4114016 Rev 3.0 January 28, 2014 44 Product Technical Specification Mechanical Drawings Figure 11. AirPrime HL6528x Module (bottom view with dimensions) 4114016 Rev 3.0 January 28, 2014 45 5. Design Guidelines 5.1. Power-Up Sequence Apply a LOW level logic to the PWR_ON pin (pin 59). When CTS is toggling to low level, the module is ready to receive AT commands. Figure 12. UART Signals during the Power ON Sequence 5.2. Module Switch-Off AT command AT*PSCPOF enables the user to properly switch the AirPrime HL6528x module off. If required, the module can be switched off by controlling the power supply. This can be used, for example, when the system freezes and no reset line is connected to the AirPrime HL6528x module. In this case, the only way to get control back over the module is to switch off the power line. VGPIO, PWR_ON and CTS signal behavior during the power off sequence is described in the figure below. Figure 13. Power OFF Sequence for PWR_ON, VGPIO and CTS 4114016 Rev 3.0 January 28, 2014 46 Product Technical Specification Design Guidelines 5.3. Sleep Mode Management AT command AT+KSLEEP enables the sleep mode configuration. AT+KSLEEP=0:
The AirPrime HL6528x module is active when DTR signal is active (low electrical level). When DTR is deactivated (high electrical level), the AirPrime HL6528x module enters sleep mode after a while. On DTR activation (low electrical level), the AirPrime HL6528x module wakes up. AT+KSLEEP=1:
The AirPrime HL6528x module determines when it enters sleep mode (when no more tasks are running). 0x00 character on the serial link wakes the AirPrime HL6528x module up. AT+KSLEEP=2:
The AirPrime HL6528x module never enters sleep mode. In sleep mode, the module reduces its power consumption and remains waiting for the wake up signals either from the network (i.e. read paging block depending on the DRX value of the network) or the operating system (i.e. timers wake up timers activated) or the host controller (i.e. character on serial link or DTR signal). 5.4. ESD Guidelines for UIM Cards Decoupling capacitors must be added as close as possible to the UIM card connectors on UIM_CLK, UIM_RST, UIM_VCC and UIM_DATA signals to avoid EMC issues and to pass the UIM card type approval tests, according to the drawings below (this applies to both UIM slots, UIM1 and UIM2). A typical schematic for hardware UIM detection is provided below. Figure 14. EMC and ESD Components Close to the UIM 4114016 Rev 3.0 January 28, 2014 47 1 Vcc2 RST3 CLK4 C4I/O 7VPP 6GND 5C8 89 SW_AUIM_DATAUIM_VCCUIM_RESETUIM_CLK100nFDNIDNIUIM_VCCUIM_DATAUIM_RESETUIM_CLKGPIOx1KSW_B 10GPIOx100K1nFVGPIO Product Technical Specification Design Guidelines 5.5. Audio Integration 5.5.1. Microphone Audio Design 5.5.1.1. Differential Connection Example Figure 15. Example of a MIC Input Connection with LC Filter The LC filter (L1, L2, C2, C3, and C4) is used to reduce EMI perturbation created by TDMA noise, but it is not mandatory. Good quality audio can be achieved without an LC filter depending on the design. Figure 16. Example of a MIC Input Connection without LC Filter Capacitor C1 is highly recommended to eliminate TDMA noise. Note that C1 must be close to the microphone. Refer to the table below for the recommended components to use with a microphone connection. 4114016 Rev 3.0 January 28, 2014 48 MICL1AUDIO ADC2.4V Typ. Internal MIC BiasZ2*=2.2k100nF100nF18pFMIC_PMIC_NL2C1C2C3C4HL6528xZ2*=2.2kMICAUDIO ADC2.4V Typ. Internal MIC BiasZ2*=2.2k100nF100nF18pFMIC_PMIC_NC1HL6528xZ2*=2.2k Product Technical Specification Design Guidelines Table 35. Recommended Components for a Microphone Connection Component Description/Details Notes C1 C2, C3, C4 L1, L2 12pF to 33pF Needs to be tuned depending on the design 47pF 100nH Needs to be tuned depending on the design Needs to be tuned depending on the design 5.5.1.2. Single-Ended Connection Example When a single-ended connection is used for MIC, MIC_N is just left open. Figure 17. Example of a Single-Ended MIC Input Connection with LC Filter The internal input impedance value becomes 1100 due to the connection of the other end to ground. The single-ended design is very sensitive to TDMA noise; it is recommended to add L1 and C2 footprint as an LC filter to try to eliminate TDMA noise. Very good grounding on the MIC is required in order to ensure good performance against TDMA. Also, special care on the PCB layout must be taken. When not used, the filter can be removed by replacing L1 with a 0 resistor and by disconnecting C2, as shown in the following figure. Figure 18. Example of a Single-Ended MIC Input Connection without LC Filter 4114016 Rev 3.0 January 28, 2014 49 MICL1AUDIO ADC2.4V Typ. Internal MIC BiasZ2*=2.2k100nF100nF18pFMIC_PMIC_NC1C2HL6528xZ2*=2.2k Product Technical Specification Design Guidelines The capacitor C1 is highly recommended to eliminate TDMA noise, and it must be placed close to the microphone. Refer to the table below for the recommended components to use with a single-ended microphone connection. Table 36. Recommended Components for a Single-Ended Microphone Connection Component Description/Details Notes C1 C2 L1 12pF to 33pF 12pF to 33pF 100nH Needs to be tuned depending on the design Needs to be tuned depending on the design Needs to be tuned depending on the design 5.5.2. Speaker Audio Design The SPKR interface can be used in a single-ended or a differential connection. However, it is strongly recommended to use a differential connection in order to reject common mode noise and TDMA noise. Moreover, in single-ended mode, half (1/2) of the power is lost. When using a single-ended connection, be sure to have a very good ground plane, very good filtering as well as shielding in order to avoid any disturbance on the audio path. The following table lists the typical values of both speaker output. Table 37. Speaker Details Parameter Typical Value Connection Z (SPKR_P, SPKR_N) () Z (SPKR_P, SPKR_N) () 32 32 Differential mode Single-ended mode It is recommended to add ESD protection to the speaker when it is exposed to the external environment. The ESD protection should be connected between the audio lines and a good ground, and placed as close to the speaker as possible. It is important to select an appropriate speaker and filtering components to avoid TDMA noise. 5.5.2.1.1. SPKR Differential Connection Note:
Add a 33pF capacitor between the SPKR_P and SPKR_N pins to reduce TDMA noise. Figure 19. Example of a Differential Connection for SPKR 4114016 Rev 3.0 January 28, 2014 50 18pFSPKR_PSPKR_NSPEAKERHL6528x Product Technical Specification Design Guidelines 5.5.2.1.2. SPKR Single-Ended Connection Figure 20. Example of a Single-Ended Speaker Connection (typical implementation) In a single-ended connection:
4.7F < C1 < 47F, depending on the speaker characteristics and output power the connection between the AirPrime HL6528x module pins and the speaker must be designed to keep the serial impedance lower than 1.5 SPKR_N can be left open output power is lost (-6dB) as compared to a differential connection 5.5.3. Audio Layout Guidelines To avoid TDMA noise, it is recommended to surround the audio tracks with ground as shown in the following figure. Figure 21. Audio Track Design For differential connections, refer to the on following figure. Note that the differential audio line is always in parallel. 4114016 Rev 3.0 January 28, 2014 51 18pFSPKR_PSPKR_NSPEAKERHL6528xC133pF~100pFC3Z hp Product Technical Specification Design Guidelines Figure 22. Differential Audio Connection For single-ended connections, the negative pole of the microphone, MIC_N, should be connected to GND. Refer to the following figure. Figure 23. Single-Ended Audio Connection Caution:
Avoid digital tracks crossing under and over the audio tracks. It is highly recommended to have the MIC ground and the LC filter ground to act as an audio analog ground during the PCB layout. This audio ground, together with the MIC_P signal, should act as the differential line pair; and this audio ground should only be connected to the AirPrime HL6528x module ground, as close as possible to the LGA GND pad of the AirPrime HL6528x module. It is the same case for SPKR_P and SPKR_N. Also, the audio interface is ESD sensitive. ESD protection MUST be added to the interface once it is externally accessible. To avoid distortion and burst noise, the following guidelines should be followed:
Audio signals must be symmetric (same components on each path) Differential signals must be routed in parallel Audio layer must be surrounded by 2 ground layers The link from one component to the ground must be as short as possible Separate the PCBs for the microphone and the speaker if possible Reduce the number of electronic components as much as possible (to avoid loss of quality and greater dispersion) Audio tracks must be wider than 0.5 mm 4114016 Rev 3.0 January 28, 2014 52 Product Technical Specification Design Guidelines 5.6. Radio Integration 5.6.1. RF Routing Recommendations To route the RF antenna signals, the following recommendations must be observed for PCB layout:
The RF signals must be routed using traces with a 50 characteristic impedance. Basically, the characteristic impedance depends on the dielectric constant (r) of the material used, trace width (W), trace thickness (T), and height (H) between the trace and the reference ground plane. In order to respect this constraint, Sierra Wireless recommends that a MicroStrip structure be used and trace width be computed with a simulation tool (such as AppCAD, shown in the figure below and available free of charge at http://www.avagotech.com). Figure 24. AppCAD Screenshot for Microstrip Design Power Mode Diagram The trace width should be wide enough to maintain reasonable insertion loss and manufacturing reliability. Cutting out inner layers of ground under the trace will increase the effective substrate height; therefore, increasing the width of the RF trace. Caution:
It is critical that no other signals (digital, analog, or supply) cross under the RF path. The figure below shows a generic example of good and poor routing techniques. 4114016 Rev 3.0 January 28, 2014 53 Product Technical Specification Design Guidelines Poor routing Correct routing The yellow traces cross the RF trace. There is no signal around the RF path. Figure 25. RF Routing Examples Fill the area around the RF traces with ground and ground vias to connect inner ground layers for isolation. Cut out ground fill under RF signal pads to reduce stray capacitance losses. Avoid routing RF traces with sharp corners. A smooth radius is recommended. E.g. Use of 45 angles instead of 90. The ground reference plane should be a solid continuous plane under the trace. The coplanar clearance (G, below) from the trace to the ground should be at least the trace width (W) and at least twice the height (H). This reduces the parasitic capacitance, which potentially alters the trace impedance and increases the losses. E.g. If W = 100 microns then G = 200 microns in an ideal setup. G = 150 microns would also be acceptable is space is limited. Figure 26. Coplanar Clearance Example Note:
The figure above shows several internal ground layers cut out, which may not be necessary for every application. 4114016 Rev 3.0 January 28, 2014 54 Product Technical Specification Design Guidelines Figure 27. Antenna Microstrip Routing Example 5.6.2. GSM Antenna Integration with Antenna Detection Circuitry The AirPrime HL6528x module is equipped with external antennas. A 50 line matching circuit between the module, the customers board and the RF antennas is required, for GSM and GPS feed path, as shown in the example below. Figure 28. GSM Antenna Connection with Antenna Detection Note:
Antenna detection circuit is optional. Rant is the equivalent DC terminating resistor of the antenna. Rant should be close to 10K. 4114016 Rev 3.0 January 28, 2014 55 Product Technical Specification Design Guidelines 5.6.3. GNSS Active Antenna Integration The AirPrime HL6528-G and HL6528-G2.8V modules embed a GPS/GLONASS receiver inside. A possible implementation with an active GNSS antenna is defined below. Figure 29. GNSS Application with Active Antenna EXT_LNA_GPS_EN is a specific signal that automatically sets the AirPrime HL6528-G and HL6528-
G2.8V modules internal LNA to low gain when an external pull-down resistor is detected. Note:
When the application needs to monitor the active antenna current, current monitor devices can be connected to any of the modules GPIOs, and read with a dedicated AT command. 4114016 Rev 3.0 January 28, 2014 56 6. X-Ray Exposure X-ray exposure results in an undesirable shift in programmed bit threshold voltage of the Flash memory. As a result, Sierra Wireless recommends avoiding any X-ray exposure during customer manufacturing process to ensure software integrity and long term reliability. In case X- ray inspection could not be eliminated from the customer manufacturing process, a variety of mitigation methods should be implemented to lower the risk of potential failure:
Use of filter between source and module to minimize exposure to harmful soft X- ray 300m Zn filter or 1mm Al filter are optimal Zn and Al absorb soft X-ray to which silicon is particularly vulnerable, and transmit soft and medium energy X-rays required to obtain good imaging Minimize X-Ray dose should be less than 10 RADs KV peak should be less than 50KV peak tube current should be less than 20A Maximize distance between source and the module Minimize the X-ray time use the shortest exposure time possible sampling only, not 100% inspection Note that these mitigation guidelines are for information only as its NOT possible to provide accurate acceptable or unacceptable X- ray exposure criteria, e.g. maximum safe dose rate, maximum safe exposure time, etc. 7. Flash memory endurance As many embedded device, the AirPrime HL6528x module is using flash memory which are guaranteed for a limited number of program/erasing cycles per sector (100,000 cycles). Although state-of-the-art mechanism has been implemented to limit the number of writing/erasing cycles, Sierra Wireless recommends using writing AT commands appropriately and with caution. Those AT commands are identified in the AirPrime HL6 and HL8 Series AT Commands Interface Guide [2]. 8. FCC/IC Legal Information 8.1. Label The AirPrime HL6528x module is labeled with its own FCC ID on the shield side. Each HL6528x variant has its own FCC ID as listed in the table below. 4114016 Rev 3.0 January 28, 2014 57 Product Technical Specification Table 38. AirPrime HL6528x FCC IDs FCC/IC Legal Information Model Name HL6528 HL6528-G HL6528-2.8V HL6528-G2.8V FCC ID N7NHL6528 N7NHL6528G N7NHL652828V N7NHL6528G28V When the module is installed in a customers product, the FCC ID label on the module will not be visible. To avoid this case, an exterior label must be stuck on the surface of the customers product to indicate the FCC ID of the enclosed module. This label can use wording such as the following:
Contains Transmitter module FCC ID: <FCC ID as listed in Table 38 AirPrime HL6528x FCC IDs> or Contains FCC ID: <FCC ID as listed in Table 38 AirPrime HL6528x FCC IDs>. 8.2. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna 2. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. 4. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 8.3. RF Exposure Information This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this transmitter, including any applicable source-
based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical Exclusion Requirements of 2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons, must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. 4114016 Rev 3.0 January 28, 2014 58 Product Technical Specification FCC/IC Legal Information The end user has no manual instructions to remove or install the device and a separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. According to the MPE RF explore report, maximum antenna gain allowed for use with this device is 5.5dBi for GSM850 and 2.0dBi for PCS1900. When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. Otherwise, a second label must be placed on the outside of the final device that contains the following text: Contains FCC ID: <FCC ID as listed in Table 38 AirPrime HL6528x FCC IDs>
The HL6528X modem may transmit simultaneously with other collocated radio transmitters within a host device, provided the following conditions are met:
Each collocated radio transmitter has been certified by FCC / IC for mobile application. At least 20 cm separation distance between the antennas of the collocated transmitters and the users body must be maintained at all times. The output power and antenna gain must not exceed the limits and configurations stipulated in the following table. Technoloty Frequency (MHz) Maximum Conducted Power (dBm) Maximum Antenna Gain (dBi) Collocated HL6528-
G2.8V Collocated Transmitters GPRS WLAN WLAN WiMAX WiMAX WiMAX BT 824-849 1850 -1910 2400 -2500 5150 -5850 2300 -2400 2500 -2700 3300 -3800 2400 -2500 1.Valid collocated transmitter combinations: WLAN+BT;
WiMAX+BT.(WLAN+WiMAX+BT is not permitted.) 34.0 31.0 29.0 29.0 29 29 29 15 2.5 2.0 5.0 5.0 5.0 5.0 5.0 5.0 8.4. IC Regulations IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This Class B digital apparatus complies with Canadian ICES-003. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than necessary for successful communication. 4114016 Rev 3.0 January 28, 2014 59 Product Technical Specification FCC/IC Legal Information Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows: Contains transmitter module IC: <IC number as listed below>. Table 39. AirPrime HL6528x IC number Model Name HL6528 HL6528-G HL6528-2.8V HL6528-G2.8V IC number 2417C-HL6528 2417C-HL6528G 2417C-HL652828V 2417C-HL6528G28V This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'I ndustrie Canada applicables aux appareils radio exempts de licence. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. 4114016 Rev 3.0 January 28, 2014 60 9. Ordering Information Model Name Part Number Designation HL6528 HL6528-G HL6528-2.8V HL6528-G2.8V DEV-KIT 1102044 1102045 1102047 1102048 6000575 HL6528, GENERIC 1.8V HL6528-G, GENERIC 1.8V HL6528-2.8V, GENERIC 2.8V HL6528-G2.8V, GENERIC 2.8V DEV-KIT, HL6 series 4114016 Rev 3.0 January 28, 2014 61 10. Terms and Abbreviations Abbreviation Definition ADC AGC AT AVL CCB CDMA CF3 CLK CODEC CPU DAC DTR Analog to Digital Converter Automatic Gain Control Attention (prefix for modem commands) Automatic Vehicle Location Customer Carrier Board Code Division Multiple Access Common Flexible Form Factor Clock Coder Decoder Central Processing Unit Digital to Analog Converter Data Terminal Ready EGNOS European Geostationary Navigation Overlay Service EMC EMI EN ESD ETSI FDMA GAGAN ElectroMagnetic Compatibility ElectroMagnetic Interference Enable ElectroStatic Discharges European Telecommunications Standards Institute Frequency-division multiple access GPS aided geo augmented navigation GLONASS GLObal NAvigation Satellite System GND GNSS GPIO GPRS GSM Hi Z IC IMEI I/O LED LNA MAX MIN Ground Global Navigation Satellite System General Purpose Input Output General Packet Radio Service Global System for Mobile communications High impedance (Z) Integrated Circuit International Mobile Equipment Identification Input / Output Light Emitting Diode Low Noise Amplifier MAXimum MINimum MSAS Multi-functional Satellite Augmentation System N/A PA PC PCB PCL Not Applicable Power Amplifier Personal Computer Printed Circuit Board Power Control Level 4114016 Rev 3.0 January 28, 2014 62 Product Technical Specification Terms and Abbreviations Abbreviation Definition PLL PWM QZSS RF RFI RMS RST RTC RX SCL SDA SIM SMD SPI SV SW Phase Lock Loop Pulse Width Modulation Quasi-Zenith Satellite System Radio Frequency Radio Frequency Interference Root Mean Square Reset Real Time Clock Receive Serial Clock Serial Data Subscriber Identification Module Surface Mounted Device/Design Serial Peripheral Interface Satellite Vehicle SoftWare PSRAM Pseudo Static RAM TBC TBD TP TTS TX TYP UART UICC USB UIM VBATT VSWR WAAS To Be Confirmed To Be Defined Test Point Text To Speech Transmit Typical Universal Asynchronous Receiver-Transmitter Universal Integrated Circuit Card Universal Serial Bus User Identity Module Main Supply Voltage from Battery or DC adapter Voltage Standing Wave Ratio Wide Area Augmentation System 4114016 Rev 3.0 January 28, 2014 63
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2014-06-11 | 1850 ~ 1910 | PCB - PCS Licensed Transmitter | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2014-06-11
|
||||
| 1 | Applicant's complete, legal business name |
Sierra Wireless Inc.
|
||||
| 1 | FCC Registration Number (FRN) |
0005810874
|
||||
| 1 | Physical Address |
13811 Wireless Way
|
||||
| 1 |
Richmond, BC, N/A V6V 3A4
|
|||||
| 1 |
Canada
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
h******@acbcert.com
|
||||
| 1 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
N7N
|
||||
| 1 | Equipment Product Code |
HL652828V
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
Y****** W******
|
||||
| 1 | Title |
Sr. Manager, Regulatory Compliance
|
||||
| 1 | Telephone Number |
604-2********
|
||||
| 1 | Fax Number |
604-2********
|
||||
| 1 |
y******@SierraWireless.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
Sierra Wireless Inc.
|
||||
| 1 | Name |
Y**** W******
|
||||
| 1 | Physical Address |
Canada
|
||||
| 1 |
y******@sierrawireless.com
|
|||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 12/09/2014 | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | PCB - PCS Licensed Transmitter | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Module | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Single Modular Approval | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Single Modular Approval. Power out is conducted at the antenna terminal. This device is to be used only for mobile and fixed application. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedures as documented in this filing. End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. For mobile and fixed operating configurations the antenna gain, including cable loss, must not exceed 5.5 dBi at 850 MHz and 2 dBi at 1900 MHz as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified in Part 22 and 24. The Grantee is responsible for providing the documentation required for modular use. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
UniLab (Shanghai) Co., Ltd.
|
||||
| 1 | Name |
W**** R****
|
||||
| 1 | Telephone Number |
86-21********
|
||||
| 1 | Fax Number |
86-21********
|
||||
| 1 |
w******@unilab.cn
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 22H | BC | 824 | 849 | 2.17 | 2.5 ppm | 257KGXW | |||||||||||||||||||||||||||||||||
| 1 | 2 | 24E | BC | 1850 | 1910 | 0.84 | 2.5 ppm | 250KGXW | |||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC