FCC ID: UUC-02 Entry Transponder

Biometric Transponder:

TRA.FP.INF2 Published December 2006 Biometric Transponder: TRA.FP.INF2 Content 1.0 General Instructions .....................................................................3 1.1 Safety instructions................................................................................ 3 1.2 Product description .............................................................................. 4 2.0 Overview of function.....................................................................5 2.1 Basic information on operation........................................................... 5 2.2 Operating states.................................................................................... 5 2.3 How the transponder works................................................................. 6 2.4

"Learn" state: start-up, scanning in fingerprints .............................. 6 2.5 Querying the number of fingerprints scanned in .............................. 9 2.6

"Recognize" mode: single triggering of transponder..................... 10 3.0 "Delete" mode: deleting fingerprints.........................................11 4.0 Transparent mode.......................................................................11 5.0 Programming the Transponder with the SimonsVoss software

......................................................................................................12 6.0 Changing the Batteries...............................................................12 7.0 Technical Data.............................................................................13 8.0 Table of Diode Signals................................................................14 Biometric Transponder: TRA.FP.INF2 Page 3 1.0 General Instructions Please take 15 minutes to familiarise yourself with how your Biometric Transponder works with the help of these operating instructions. Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help Industry Canada Statement per Section 4.0 of RSP-100 The term "IC:" before the certification / registration number only signifies that the Industry Canada technical specifications were met. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Safety instructions o Caution! The batteries used in this product could burn or cause a fire if they are not handled properly. Do not charge, open or burn these batteries or heat to over 100C. o Make sure that the sensor surface is not dirty or scratched. Do not drop the transponder or expose it to any other strong impacts. In addition, please make sure that the initial scanning in of fingerprints is not carried out by unauthorized people. o 1.1 Biometric Transponder: TRA.FP.INF2 Page 4 o Programming should only be carried out by trained specialist staff. o SimonsVoss Technologies, Inc. is not liable for any damage caused by incorrect programming. 1.2 o An incorrectly programmed or faulty transponder can block access through a door. SimonsVoss Technologies, Inc. is not liable for the consequences of such an occurrence, such as blocked access to persons who are injured or in danger, material damage or any other damage. Product description The biometric transponder differs from a standard transponder by the fact that it is also equipped with a highly sensitive Atmel Fingerprint Sensor. In just a few seconds, a high-powered processor in the transponder compares the saved fingerprint with the fingerprint read in by the sensor. In this way, only people whose fingerprints have been already scanned can use the transponder. This guarantees maximum security against unauthorized use by third parties, e.g. if the transponder is unsupervised, or is lost or stolen. The Biometric Transponder is therefore particularly suitable for applications where a transponder is provided with very many or very specific authorizations, e.g. if one person has a general transponder for all doors or access to high-security areas. Biometric Transponder: TRA.FP.INF2 Page 5 2.0 Overview of function 2.1 Basic information on operation The Biometric Transponder scans fingerprints using a fingerprint sensor. The finger is dragged across the sensor, rather than being pressed against it. The following should be noted:

The fingerprint to be scanned and memorized should always be dragged over the sensor in the same way. To do this, place the tip of the finger that is to be stored at the upper edge of the transponder and draw it across the sensor bar from top to bottom (towards the button) at a constant speed while applying a slight pressure. The design of the housing means that the finger is guided properly through the slightly raised side walls. The fingerprint sensor scans the fingerprint line by line and reassembles it into a complete image in the integrated processor. If the reassembled image matches the saved image, the transponder is activated. 2.2 Operating states The Biometric Transponder has four different operating modes:

Mode Standby Learn Delete Recognise Function The transponder is normally on "Standby" in order to save the battery capacity. After it has completed a function (e.g. scanning), it always returns to the standby mode. In the "Learn" mode, new fingerprints can be memorized. Up to 6 different fingerprints can be saved, two of which are what we call

"administrator" fingerprints. New fingerprints (user fingerprints) can only be scanned in with the help of an administrator. The only exception is the scanning of the first two fingerprints (Administrator fingerprints), see below In the "Delete" mode, fingerprints that have been memorized can be deleted. Individual prints can be deleted, or all fingerprints can be deleted at once. The "Recognize" mode is the mode before a door is opened. In this mode, the Transponder is released if a fingerprint is correctly recognized. Biometric Transponder: TRA.FP.INF2 Page 6 2.3 How the transponder works Stand-by mode: LED not illuminated Briefly press button once, then release Recognize mode: LED flashes green Press button and hold down for 3 sec. Drag finger across sensor Transponder triggered Learn mode: LED flashes yellow Press button and hold down for 3 sec. Drag Administrator finger once over sensor and new finger (User finger) 3 times over sensor. New finger is memorized Delete state: LED flashes red Draw Administrator finger once across sensor Draw user finger once across sensor All fingerprints are deleted Only user fingerprint is deleted 2.4 You can interrupt the action in each mode by pressing the button briefly to change to Standby.

"Learn" state: start-up, scanning in fingerprints Initial start-up - scanning in the first 2 fingerprints (Administrator fingerprints) To start the Biometric Transponder, two "Administrator fingerprints" need to be scanned in first. We recommend that a fingerprint from the left and right hand of one person, the administrator (e.g. safety officer) is used for this; however, you can also use one finger from two different people. Biometric Transponder: TRA.FP.INF2 Page 7 Please note:

The first two fingerprints scanned in are automatically the Administrator fingerprints. Without them, no further fingerprints can be scanned in or deleted later!

To scan in and store the first Administrator fingerprint (e.g. left thumb), please do the following:

1. Briefly press the transponder button; the LED will flash green. 2. Then press the button again and hold it pressed for at least 3 seconds (until the LED flashes yellow). 3. Release the button. The system is now ready to scan for 30 seconds, and this is indicated by rapid yellow flashing. 4. Since quality or the fingerprint must be high for good recognition during every day use, please make sure, that the finger to be scanned is not too dry (e.g. breath on them before having them scanned in). 5. Drag your finger across the sensor. The LED goes off after about 1 second. Then the LED flashes green once to indicate that the fingerprint has been accepted. 6. When the LED flashes yellow rapidly again, drag the finger to be scanned across the sensor again. 7. Now repeat steps 4 and 5 twice again (so that you have drawn your finger three times across the fingerprint sensor altogether). If an attempt has been unsuccessful (LED is illuminated red), drag your finger across the sensor again. Using for the first time learning the first two fingers (Administrator Fingers) Once the fingerprint has successfully been scanned, the data is saved. This step takes about 2 to 5 seconds and is indicated by a yellow light flashing at 2 second intervals. The diode is then briefly illuminated green, and the Biometric Transponder returns to Standby. The Biometric Transponder can now be used by the Administrator, or other fingerprints can be entered. Please note that the second fingerprint that is scanned in also has Administrator rights!

Biometric Transponder: TRA.FP.INF2 Page 8 Scanning more fingerprints (User fingerprints) Further fingerprints (maximum 4 beyond the initial 2) can be scanned in as the Administrator fingerprints have been, except that the Biometric Transponder must first be cleared for this by an Administrator fingerprint. This prevents unauthorized persons from scanning in their own fingerprints and thus gaining access rights that are not allowed. While the Biometric Transponder can be programmed to recognize four user fingerprints, we recommend that each transponder be limited to one person who scans two fingers, one from each hand. If the user enters each finger twice it increases the ability of the scanner to correctly recognize the proper fingerprint. To scan in more fingerprints, please proceed as follows:

1. Briefly press the transponder button and wait until the LED flashes green. 2. Then press the button again and hold it pressed for at least 3 seconds until the LED flashes yellow, then release the button. 3. Draw the Administrator finger across the sensor; the LED goes off and then flashes green once after about 2 seconds. The system is now ready to scan for 30 seconds, and this is indicated by rapid yellow flashing light. Drag the User finger across the sensor; the LED goes off; after about 1 second, the LED flashes green once to indicate that the fingerprint has been accepted. 4. When the LED flashes yellow rapidly again, draw the finger to be scanned in across the sensor again. 5. Now repeat step 4 twice again (so that you have drawn your finger three times across the fingerprint sensor altogether). If an attempt has been unsuccessful (LED is illuminated red), drag your finger across the sensor again. Once the fingerprint has successfully been scanned, the data is saved. This step takes about 2 to 5 seconds and is indicated by a yellow flashing light at 2 second intervals. The diode is then briefly illuminated green, and the transponder returns to Standby. Fingerprints that are already known can always be scanned in, even if 6 fingerprints have already been saved. Unknown fingerprints are then rejected by the LED flashing red twice. Tips:

Care in scanning in is rewarded by reliable recognition in use. Scanning in the same fingerprint several times improves the quality of the scanned features and thus makes the recognition of the fingerprint more reliable. Use a firm base when scanning in fingerprints. We recommend operation with one hand when scanning in thumb prints. When scanning in fingerprints, drag the finger across the sensor in a straight line, not too quickly, at an even speed and pressure. Make sure that the sensor is clean and that your fingers are not too dry (e.g. by breathing on them before having them scanned). 6. Now repeat step 4 twice again (so that you have drawn your finger three times across the fingerprint sensor altogether). If an attempt has been unsuccessful (LED is illuminated red), drag your finger across the sensor again. Biometric Transponder: TRA.FP.INF2 Page 9 2.5 Querying the number of fingerprints scanned in You can discover the number of fingerprints already entered as follows:

1. Press the button once briefly (the LED flashes green) 2. Press the button again and hold it down for 1.5 to 2 seconds (not as long as 3 seconds, which will take you into "learn" mode). 3. The LED flashes red. 4. Then the LED will flash green as many times as the number of fingerprints entered

(maximum of 6). 5. The LED flashes red (for a long time if the maximum possible number of fingerprints has been reached, or briefly if it has not). If no fingerprints have been entered, the LED flashes red twice and then returns to Standby mode. Biometric Transponder: TRA.FP.INF2 Page 10 2.6

"Recognize" mode: single triggering of transponder The mode known as the Recognize mode is the normal operating state for the Biometric Transponder. This mode is entered when a person whose fingerprint has been authorized would like to open a door protected by a SimonsVoss RF lock. To do this, proceed as follows:

1. Press the button of the Biometric Transponder briefly (for around 0.5 sec.), and the LED will then flash green. 3. 2. Now drag your authorized finger over the sensor. Make sure that it is in the same position as it was when you scanned it in. If the recognition attempt was successful, the LED shows green and the Transponder is activated. If the LED shows red, the recognition attempt was not successful. You can now try three more times. If these are not successful, the Biometric Transponder automatically returns to Standby mode. Please note:

It may occasionally happen that the Biometric Transponder does not recognize your finger even though it has been properly scanned in. If the fingerprint is rejected with a single red flash, the quality of the fingerprint trace was not adequate. This may be due to the fact, for example, that you did not drag your finger properly across the sensor (too quickly, not straight or not even) or that the surface of the sensor is dirty. If a finger is too dry, it may happen that it skips across the sensor. If this happens, please repeat the attempt, or moisten your finger slightly before you do so by breathing on it, for example. With a little practice, however, you'll soon get the knack. If the features of your fingerprint cannot be assigned to any of the scanned fingerprints, the diode will flash red twice. You may have accidentally presented a fingerprint that has not been scanned in, or you may have drawn this finger across the sensor quite differently initially from the way you are doing it now (e.g. at an angle, or with more or less of your fingertip in contact with the sensor). Tip:

Not every fingerprint from a person is recognized equally reliably. If you are often not recognized with one finger, you should perhaps scan in another finger. Make sure that the sensor is clean and that your fingers are not too dry (e.g. by breathing on them before having them scanned). Biometric Transponder: TRA.FP.INF2 Page 11 3.0

"Delete" mode: deleting fingerprints Both individually scanned fingerprints and all the fingerprints can be deleted from the memory. If normal fingerprints (not Administrator fingerprints) are deleted, the other fingers that have been scanned in are not deleted. No Administrator fingerprint is needed to do this (any normal user can delete his own fingerprint). If one of the two Administrator fingerprints is deleted, all the fingerprints are automatically deleted. The first two fingerprints that are then scanned in are automatically the Administrator fingerprints again. Fingerprints are deleted as follows:

1. Briefly press the transponder button and wait until the LED flashes green. 2. Then press the button again and hold it pressed for at least 3 seconds until the LED flashes yellow. Release the button. 3. Press the button again and hold it pressed for at least 3 seconds until the LED flashes red. Release the button. You are now in the "Delete" state. 4. Drag finger across sensor. 5. If the first recognition attempt was successful, the LED flashes green. If the fingerprint is a normal one (user fingerprint), only this fingerprint is deleted; if it was one of the two Administrator fingerprints, then all the fingerprints are deleted. Deleting all the fingerprints can take up to 15 seconds. During this time, the diode flashes red every 2 seconds. If the LED flashes yellow, the recognition attempt was not successful. You can now try three more times. If these all fail, the transponder automatically returns to Standby mode. 6. 4.0 Transparent mode It is possible to switch the Biometric Transponder to what is called Transparent mode. In this state, the biometric inquiry is suspended for 5 minutes and the Biometric Transponder can be used as a normal transponder (doors can be opened simply by pressing a button). At the end of 5 minutes or so, the Biometric Transponder returns to Standby mode. Transparent mode is required, for example, for setting/cancelling alarms (if an SV Shuntlock VdS is installed) or if several doors need to be passed through in a short time. To enter Transparent mode, please proceed as follows:

1. Press and hold the transponder button (longer than 1.5 seconds, < 3 sec.). The LED will flash green rapidly. The Transponder will now react to the button as if it were in Recognize mode. 2. Drag finger across sensor (LED shows green if the fingerprint is recognised). 3. The Biometric Transponder is triggered and switches to Transparent mode. The LED flashes red. flashing. 4. Pressing the button triggers the system and the LED shows green, followed by red After 5 minutes, the Transponder switches off Transparent mode and returns to Standby. Transparent mode can also be switched off manually by pressing the Transponder button before automatic switch-off until the green LED goes out (approx. 1.5 sec). Biometric Transponder: TRA.FP.INF2 Page 12 5.0 Programming the Transponder with the SimonsVoss software The "Set validity" function and the "Quasi-proximity mode" are not available for the Biometric Transponder. 6.0 Changing the Batteries To replace the batteries, push the battery cover downwards and remove. Take out all the batteries and replace with new ones. Make sure that the polarity is correct (stamped into the base of the battery compartment). Biometric Transponder: TRA.FP.INF2 Page 13 7.0 Technical Data Dimensions: H x W x D Weight Colour Operating distance, locking cylinders Operating distance, Smart Relay Protection category Operating temperature range Battery type 2.8 x 1.3 x 0.7 in

(265 x 32 x18 mm) 0.8 oz (22 g) Dark Grey, with blue button approx. 16 inches (40 cm) if the transponder, lengthways, is held parallel with the cylinder antenna. approx. 47 inches (120 cm) if the transponder is parallel with the antenna of the SmartRelay. IP 54 (NEMA 3S)

-4F to 104F (-20C to 40C) without condensation 3 V DC lithium battery type CR-1/3N Biometric Transponder: TRA.FP.INF2 Page 14 8.0 Table of Diode Signals LED off off Slow green flashing light Fast green flashing light One green flash Slow yellow flashing light Fast yellow flashing light Yellow flashing light One or two yellow flashes Slow red flashing light Red flashing light Red flashing light Flash red 1x Flash red 2x Red, 0 to 6 times green, red Mode Standby moving finger on sensor followed by comparison with scanned fingerprint, please wait (max. 4 seconds) Recognize mode, wait for finger

(max. 30 seconds) Release for transparent mode, wait for finger

(max. 30 seconds) Successful action (recognize, learn, save, delete, trigger) Release for Learn mode, wait for Administrator finger (max. 30 seconds) Learn mode, wait for finger (max. 30 seconds) Save scanned finger, please wait (max. 5 seconds) Error message in Delete state (cf. 1x or 2x red flashing) Delete state, wait for finger (max. 30 seconds) Delete scanned fingerprint, please wait (max. 15 seconds) Transparent state (max. 5 minutes) Action unsuccessful Fingerprint not recognised Query number of scanned-in fingerprints

Transponder:

TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Published December 2006 Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Content 1.0 General Instructions .....................................................................3 Safety instructions........................................................................................... 3 1.2 Product description .............................................................................. 4 1.1 Higher Priority Locking Level.............................................................. 5 2.0 Special Models ..............................................................................6 2.1 Password Transponder ........................................................................ 6 2.2 Switching Transponder ........................................................................ 6 2.3 Explosion-Proof Transponder ............................................................. 6 Transponder, Sealed............................................................................. 6 2.4 2.5 Transponder, Sequentially Numbered................................................ 6 3.0 Explosion-Proof Standards..........................................................7 3.1 General Information.............................................................................. 7 3.2 Standards............................................................................................... 7 3.3 Grouping ................................................................................................ 7 4.0 Additional Functions.....................................................................8 4.1 Time Zone Control ................................................................................ 8 4.2 Validity Date........................................................................................... 8 4.3 Activation Transponder........................................................................ 8 5.0 Battery Replacement.....................................................................9 5.1 Standard, Switching, and Password Transponders.......................... 9 5.2 Battery Replacement for the Explosion Protection Transponder ... 9 6.0 Loss of the Transponder ..............................................................9 6.1 Emergency Opening ............................................................................. 9 6.2 Replacement Transponder................................................................... 9 7.0 Programming and Reading the Transponder .............................9 7.1 Programming a Transponder............................................................. 10 7.2 Reading a Transponder...................................................................... 10 8.0 Data Sheet....................................................................................11 Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 3 1.0 General Instructions Please take 15 minutes to familiarize yourself with how your Transponder works with the help of these operating instructions. Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help Industry Canada Statement per Section 4.0 of RSP-100 The term "IC:" before the certification / registration number only signifies that the Industry Canada technical specifications were met. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. o Caution! The batteries used in this product could burn or cause a fire if they are not handled properly. Do not charge, open or burn these batteries or heat to over 100C. o SimonsVoss Technologies, Inc. is not liable for any damage caused by incorrect programming. o An incorrectly programmed or faulty transponder can block access through a door. SimonsVoss Technologies, Inc. is not liable for the consequences of such an occurrence, such as blocked access to persons who are injured or in danger, material damage or any other damage. Safety instructions Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 4 1.2 Product description TRA TRA.ROT TRA.SCHALT TRA.PWD Transponder Transponder Switching Transponder Password Transponder Blue Button Red Button The Transponder is activated when the user presses the button in the center of the device. This device communicates an identity code to a SimonsVoss RF Lock or SmartRelay through an encrypted, rolling-code radio signal. If the identification corresponds with one that is authorized, the lock is unlocked or the SmartRelay is activated. The color of the button on the transponder has no significance beyond appearance. Since the Transponders communication is encrypted, it must be synchronized to the locks with a common encryption signature. This is accomplished when it is programmed with the configuration tool connected to the software used to define the lock system. Each Transponder has the ability to support up to three unique lock systems independently. This means that the user can use the same transponder on up to three different lock systems even if each lock system has a different system administrator that has no communication with the other two administrators. Private home Branch Example:

Company 900 lockings 85 lockings 3 lockings Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 5 1.1 Higher Priority Locking Level Company D Company C If it is necessary to have transponders that are authorized for more than 3 mutually independent lock systems, higher priority lock levels must be set up in these lock systems. A maximum of 3 higher priority locking levels are available for this. All transponders of a higher priority locking level have the same authorization. One digital lock distinguishes between a maximum of three higher priority levels. Example:

Higher priority transponder In this example, four companies are accommodated in an office building with a central lock that is used by all the companies. Each company administers its own lock system with its own password. Every employee receives a transponder that is authorized for 2 lock systems, namely the central lock and his or her own company. However, the fire department, for example, needs a transponder that is authorized for all five of the buildings lock systems. To accomplish this, a higher priority lock level with the same password must be set up in all five lock systems and the authorizations must be set up for the higher priority transponders. The transponders set up in this level all have the same authorization. If higher priority transponders with other authorizations are required, an additional higher priority lock level must be set up (max. 3 higher priority lock levels per lock!). The higher priority transponder must then be programmed into all shutdowns of all 5 lock systems. Central locking system Company B Company A Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 6 2.0 Special Models 2.1 2.2 2.3 2.4 2.5 Password Transponder Instead of manually entering the locking system password, you can transmit it over radio frequency with the help of a special transponder. Standard transponders cannot be used as password transponders. The Password Transponder is special version that sends an encoded password rather than an ID. The purpose of this device is to allow a system administrator to temporarily authorize someone to use the programming software without actually disclosing the password. The way this works is that the administrator encodes the password into this special transponder and then gives the transponder to the temporary operator. When the system requests the password, the new operator presses the button on the password transponder and the required password is sent to the software with the SmartCD configuration tool acting as the reader. When the temporary operator has completed his or her tasks and returns the password transponder, that person no longer has access and the system administrator does not have to worry that the password was compromised. Warning: If the Password Transponder is ever programmed as a normal Transponder, it can never again be used as a Password Transponder. Switching Transponder The Switching Transponder is identical to the Transponder with the addition of two wires connected in parallel to the button on the device. These wires allow a third-party electronic system to activate the Switching Transponder as if someone had pressed the button. The button on the Switching Transponder remains usable. Explosion-Proof Transponder This is a transponder with the same functions as the standard transponder, but in addition, this transponder can safely be used in an explosion protection zone 1.

(Note Chapter 3 in this regard). Transponder, Sealed This is the standard transponder as described above, but with the case glued shut. This prevents end-users from opening the case and using the transponder electronics improperly, but this also eliminates battery replacement so that the lifespan of the device is limited to the 1 million operations expected from the original battery. Transponder, Sequentially Numbered Sequentially numbered transponders can also be ordered if required. Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 7 3.0 Explosion-Proof Standards 3.1 3.2 3.3 General Information This special product is a transponder that is permitted to be carried into and used in areas subject to explosion hazards, called Zone 1. An area is denoted as Zone 1 when atmospheres capable of exploding occur occasionally. It is crucial that you keep in mind the following issues:

The user is not permitted to open the housing. Unlike the standard Transponder, only SimonsVoss Technologies AG is permitted to change the battery. Normally, you must comply with the general operating instructions of the BGR132

(German rules for occupational safety and health) when using the device in Zone 1. Directive 94/9/EC DIN EN 50014 (Electrical apparatus for potentially explosive atmospheres) DIN EN 50020 (Intrinsic safety "i") Standards The transponder has been tested according to the applicable explosion protection standards. Refer to:

Grouping The transponder is grouped in the following way:

This applies to areas in which a potentially explosive atmosphere can arise due to gases, vapors or mists. The information quoted relates to an ambient temperature of from -4F to

+104F (-20C to +40C) where the transponder is used. Explosion protection: zone 1 Intrinsic safety: ib Explosion group: IIC Temperature class: T3 Device group: II2 G Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 8 4.0 Additional Functions 4.1 4.2 4.3 The following functions can be activated in the lock plan software:

Time Zone Control If the Time Zone Control has been enabled in the SimonsVoss RF locks, you can program transponders that have lock authorization for specific times only. These time zones are deposited in the lock plan software, and the transponders are then assigned to an appropriate time zone group. Example:

Mr. Miller receives the following authorization:

Monday to Friday Saturday Sunday from 9:00 am, until 6:30 p.m. from 9:00 am, until 12:45 p.m. no authorization Validity Date It is possible to program transponders whose authorization is tied to a validity date:

Transponders that are valid from a specific point in time

(i.e. from 8:00 a.m. on July 12, 2003) Transponders that are valid up to a specific point in time

(i.e. until 5:00 p.m. on July 12, 2003) Transponders that are valid for a specific time interval

(i.e. from July 1, 2003 until July 31, 2003)

Note: One data record is assigned for each activation or expiration date!

Activation Transponder Within the scope of the block lock function, all authorized transponders for a SimonsVoss RF lock in the security area are blocked when the alarm system has been activated in order to avoid false alarms. For emergency situations, transponders can be programmed (for example, for the fire department) that release this block. Afterwards, the door can be opened with an authorized transponder. Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 9 5.0 Battery Replacement 5.1 5.2 6.1 6.2 Standard, Switching, and Password Transponders It is possible to damage the transponder if battery replacement is handled incorrectly. This procedure should only be attempted by a trained electronic technician. If it takes you longer than two minutes or if the battery terminals are shorted, the data in the transponder will be lost and the transponder must be reprogrammed. Before opening the transponder make sure that you are electrically grounded with an approved anti-static heel or wrist strap. Electrostatic discharge can destroy or shorten the life of a transponder. The SimonsVoss Technologies, Inc warranty does not cover damage caused by improper battery replacement. To replace the batteries, gently pry the case apart by inserting a fingernail or knife blade into the seam at the equator of the device. When the case has been opened you will see the battery held to the board by a clip. Orient the device so that the keychain hole is at the top and the antenna is to your right. Remove the clip by gently pressing on the bottom of the clip while sliding it to the left. The bottom of the clip should then be able to be pulled up and away from the board, allowing the battery to be removed. When inserting the new battery, make sure that the polarity is correct with the positive terminal up (the large side with the writing is the positive terminal). Replace the retaining clip being sure to press gently and slide it to the right to re-engage the tension on the battery. Replace the cover on the transponder. Read the transponder to verify that the data is still intact. Battery Replacement for the Explosion Protection Transponder Attention:

Only SimonsVoss Technologies, AG is permitted to change the battery for an Explosion Proof Transponder! Any attempt to change the battery outside SimonsVoss production facilities voids its use as an explosion-proof device. 6.0 Loss of the Transponder Emergency Opening An emergency opening can be carried out using the SmartCD + PDA (only use devices approved by SimonsVoss) and knowledge of the lock system password. Replacement Transponder If a transponder is lost, it can be deleted from the lock plan and a replacement transponder can be set up. When operating the lock system in overlay mode, the lost transponder is automatically blocked as soon as the replacement transponder is activated at the RF lock. 7.0 Programming and Reading the Transponder Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 10 7.1 7.2 See the appropriate software manual to learn the details of how to program and read the transponder but the following should be helpful. Programming a Transponder Before it can be used with a lock system, the Transponder must be programmed. This pro-

gramming is necessary to give it the identification code assigned by the lock system and to give it the encryption key appropriate to that system. Before you can program a transponder you must be authorized to do so. This is accomplished in the SimonsVoss software by selecting the function titled Authorize Transponder Program-

ming and providing the appropriate password. To program a transponder, it must be placed within 18 inches but no closer than four inches to the configuration tool, which is connected to the computer running the programming software. In the SimonsVoss software select the transponder you want to program on the lock plan by left-clicking on the transponder name; resulting in that transponder being highlighted. Select the function titled Program Transponder. A dialog will appear and you should confirm that the appropriate transponder is indicated before pressing the Program button. If for some, reason, the transponder listed is not the correct one, simply select the correct one from the combo box before proceeding. The software will then direct you to press the button on the transponder one or more times. Follow the instructions and the software will tell you whether the procedure was successful or not. If it was not successful, the reasons may be one of the following:

1) The transponder was too close to the configuration tool move the transponder at least 4 inches away from the configuration tool and try again. 2) The transponder has already been programmed for three different systems to use with this system the transponder must be reset (losing the other programming information). 3) There is too much RF interference move the computer, configuration tool, and trans-

ponder to another location and try again. Reading a Transponder Before it can be used with a lock system, the Transponder must be programmed. This pro-

gramming is necessary to give it the identification code assigned by the lock system and to give it the encryption key appropriate to that system. After the lock has been programmed, the Transponder can be read and will disclose the user name and time restrictions, if any. If the Transponder is unknown to the lock system, reading it will result in the display of the SID (system identification) and TID (transponder identifica-

tion). In order to read a transponder, select the Read Transponder function in either the LDB or LSM software. This function will direct you to press the button on the Transponder and will then display the result. Transponder: TRA, TRA.ROT, TRA.SCHALT, TRA.PWD Page 11 8.0 Data Sheet Dimensions: H x W x D Weight Color Operating distance, RF Locks Operating distance, SmartRelay Protection category Operating temperature range Battery type 1.7 in diameter x 0.5 in thick

(42 mm diameter x 13 mm thick) 0.5 oz (15 g) Dark Grey, with blue button approx. 16 inches (40 cm) if the transponder, lengthways, is held parallel with the RF Lock antenna approx. 47 inches (120 cm) if the transponder is parallel with the antenna of the SmartRelay IP 54 (NEMA 3S)

-4F to 104F (-20C to 40C) Noncondensing 3 V DC lithium battery type CR2032

Wireless Keypad:

TRA.PINCODE Published: December 2006 Wireless Keypad: TRA.PINCODE Content 6.0 5.0 2.0 5.1 5.2 1.1 1.2 2.1 2.2 2.3 4.1 4.2 4.3 3.0 4.0 1.0. GENERAL INFORMATION.................................................................................................................... 3 SAFETY REMARKS..................................................................................................................................... 3 PRODUCT DESCRIPTION............................................................................................................................. 4 FUNCTIONAL OVERVIEW.................................................................................................................... 4 FUNCTION OVERVIEW ............................................................................................................................... 4 OPERATING MODES.................................................................................................................................... 5 OPERATING................................................................................................................................................ 5 START-UP................................................................................................................................................... 6 PROGRAMMING PINS............................................................................................................................ 7 FIRST START-UP ........................................................................................................................................ 7 PROGRAMMING ADDITIONAL PINS........................................................................................................... 7 PROCEDURE............................................................................................................................................... 8 DELETING PINS........................................................................................................................................ 8 DESCRIPTION ............................................................................................................................................. 8 PROCEDURE............................................................................................................................................... 9 PROGRAMMING THE TRANSPONDER............................................................................................. 9 ASSIGNMENT OF PINS AND TRANSPONDERS ............................................................................................ 9 DESCRIPTION ........................................................................................................................................... 10 PROCEDURE............................................................................................................................................. 11 READING TRANSPONDERS................................................................................................................ 11 DESCRIPTION ........................................................................................................................................... 11 PROCEDURE............................................................................................................................................. 11 RESETTING TRANSPONDERS ........................................................................................................... 12 DESCRIPTION ........................................................................................................................................... 12 PROCEDURE............................................................................................................................................. 12 OPENING .................................................................................................................................................. 13 9.0 10.0 MEANING OF THE LED........................................................................................................................ 13 11.0 BATTERY WARNING ............................................................................................................................ 14 12.0 BATTERY REPLACEMENT................................................................................................................. 14 SPECIAL FUNCTIONS........................................................................................................................... 16 13.0 13.1 HIDDEN LOCK FOR SIMONSVOSS VDS SHUNTLOCK 3066...................................................................... 16 13.2 MISCELLANEOUS..................................................................................................................................... 17 14.0 TECHNICAL SPECIFICATION ........................................................................................................... 17 6.1 6.2 6.3 7.1 7.2 8.1 8.2 7.0 8.0 Wireless Keypad: TRA.PINCODE Page 3 1.0. General information Please read through these instructions in order to familiarize yourself with the functions of your Wireless Keypad. Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help Industry Canada Statement per Section 4.0 of RSP-100 The term "IC:" before the certification / registration number only signifies that the Industry Canada technical specifications were met. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Safety Remarks Caution! Incorrect handling of the batteries used in this product can result in the risk of fire or burns. Do not charge, open or burn these batteries or heat them to more than 212F (100C). Make sure that the Wireless Keypad remains free of dirt and scratches; do not drop the keypad or otherwise subject it to heavy impacts. 1.1 Wireless Keypad: TRA.PINCODE Page 4 Furthermore, please note that you should program the keypad with a PIN code immediately after you start it up. Use of a SimonsVoss Wireless Keypad requires knowledge of the use of the product and of the SimonsVoss software. For this reason, only trained and authorized personnel should program the Wireless Keypad. SimonsVoss Technologies, Inc. will not accept any liability for damages caused by incorrect programming. If the Wireless Keypad is incorrectly programmed or is defective, access through a door may be blocked. SimonsVoss Technologies, Inc. is not liable for the consequences, such as blocked access to injured or endangered persons, property damage or other damages. The casing of the Wireless Keypad is secured with two Torx screws (TX6) for increased security against unauthorized opening. 1.2 Product Description The Wireless Keypad is a digital "key" (transponder), which opens SimonsVoss locks without contact via radio transmission after the correct numerical code is entered. To configure the system, you must first correctly configure at least one PIN and the associated integrated transponder for the lock. The associated lock is then released after a correct PIN has been entered. The Wireless Keypad that you have purchased is a product that can be used both indoors and outdoors. The product has its own power supply, so that it can be operated self-sufficiently. Installation is simple, because no cabling is required. This component can be seamlessly integrated into the SimonsVoss System 3060, and, like all SimonsVoss components, it can be programmed with either LDB or LSM software. 2.0 Functional Overview 2.1 Function Overview The Wireless Keypad has the following components:

PIN code input and evaluation Integrated transponder, which opens the associated SimonsVoss RF lock when it is triggered after the PIN code has been evaluated successfully. Consequently, the Wireless Keypad allows you to address all SimonsVoss RF locks

(Cylindrical, Mortise, and Smart Relays) using the PIN code. Individual PIN codes can be assigned to up to 3 people or groups of people. When a PIN is reprogrammed, only one of up to three user groups needs to be informed. Furthermore, in the appropriate SimonsVoss locks, it is possible to grant a person or group of people access to a building only during certain times, and to keep a record of which PIN accessed the lock at what time. Wireless Keypad: TRA.PINCODE Page 5 2.2 Operating modes The Wireless Keypad has four distinct operating modes:

Mode:

Standby Opening Programming Explanation:

The Wireless Keypad is in standby mode, and uses very little power. After a correct PIN has been entered, the lock is addressed via radio transmission and can be operated. In this mode, the following can be programmed or reset:

the individual PINs (max. 3) - directly via the Keypad or the associated integrated transponders (max. 3) - using the SimonsVoss software Battery warning A multi-level battery warning system provides plenty of advance notice when it is almost time to change the batteries. 2.3 Operating Using the Wireless Keypad is a simple matter of entering the correct number of digits in the correct order. If the correct PIN is entered the appropriate transponder integrated in the keypad sends a signal to the adjacent SimonsVoss lock or SmartRelay resulting in unlocking the door or activating the relay respectively. Each of the three integrated transponders in the Keypad can be programmed, read, or reset with the LDB or LSM software. The following pages describe the procedures for using and programming the Wireless Keypad. Wireless Keypad: TRA.PINCODE Page 6 3.0 Start-up The first time the Wireless Keypad is installed, you will need to replace the factory-set master PIN: 1 2 3 4 5 6 7 8 with your own master PIN. Requirement:

The new master PIN must be 8 digits and may not start with a "0"

Enter "0000"

Your personal master PIN is needed to authenticate all programming processes. Choose a number that is easy for you to remember and keep it in a safe place where it cannot be accessed by unauthorized persons. To change the default master PIN, follow this procedure:

Repeat "your master PIN"

Enter "your master PIN Enter "1 2 3 4 5 6 7 Wireless Keypad: TRA.PINCODE Page 7 4.0 Programming PINs 4.1 4.2 The Master PIN required for all programming procedures is defined by the user

(typically the System Administrator). Please keep this PIN safe and inaccessible to unauthorized persons, since the Master PIN enables all reprogramming of the Wireless Keypad. First Start-up For the first start-up, the safety of your lock system requires that you program at least one PIN. Only after the Wireless Keypad has been programmed can it be guaranteed that only authorized users receive access. Proceed as follows:

1. Press the "0" to change to programming mode. 2. Enter the "master PIN ". 3. Select the PIN that you want to program;

in this example, press "1" for "PIN 1". 4. Enter the length of the PIN (you can choose a number with 4 to 8 digits). 5. Enter the "PIN"

6. If the input was correct, the PIN is saved and confirmed. A PIN is not permitted to begin with "0" and you may not assign the same PIN more than once. The master PIN is used only for programming the PIN. It is not possible to operate locks with the master PIN. Programming Additional PINs. 1. To program additional PINs, please proceed as follows: Press the "0" to change to programming mode. 2. Enter the "master PIN". 3. Press

"2" for "PIN 2" or

"3" for "PIN 3". 4. Enter the length of the PIN (you can choose a number with 4 to 8 digits). 5. Enter the corresponding "PIN". 6. If the input was correct, the PIN is saved and confirmed. It is not possible to enter programming mode when there is a battery warning. This means that when the battery is weak, you cannot change or delete a PIN. Programming mode will only be available again after you have successfully changed the battery (see the section "Battery Replacement). Wireless Keypad: TRA.PINCODE Page 8 4.3 Procedure Input "1

(for PIN 1) 5.0 Deleting PINs Input "0"

Input "master PIN"

Input "2"

(for PIN 2) Input "3"

(for PIN 3) Input PIN length 4, 5, 6, 7 or 8 Input "PIN"

5.1 Description To deactivate a PIN, follow these steps:

1. 2. 3. 4. 5. Press "0" to change to programming mode. Enter the "master PIN ". Press For the PIN length, enter "0". If the input was correct, the PIN in question is deleted.

"1" for "PIN 1" or

"2" for "PIN 2" or

"3" for "PIN 3". In this way, you can deactivate one or more PINs. They can only be reactivated if you program them again. If you do not need all the PINs, you can leave one or two unprogrammed. Wireless Keypad: TRA.PINCODE Page 9 It is not possible to enter programming mode when there is a battery warning. This means that it is not possible to change or delete PINs when there is a weak battery. Programming mode will only be available again after you have successfully changed the battery (see the section "Battery Replacement). Procedure 5.2 Input "0"

Input "master PIN"

Input "1"

(for PIN 1) Input "2"

(for PIN 2) Input "3"

(for PIN 3) Input PIN length "0"

6.0 Programming the Transponder Assignment of PINs and Transponders 6.1 PIN1 Transponder 1 PIN2 Transponder 2 PIN3 Transponder 3 Each integrated transponder has its own transponder ID (TID); the TIDs are saved in the SimonsVoss locks as part of the audit trail. In this way, you have a record of which PIN was used to gain access and when. Wireless Keypad: TRA.PINCODE Page 10 6.2 Description Generally to program a transponder using the SimonsVoss software you activate the appropriate function in the software and then it directs you to press the button on the transponder one or more times. The Wireless Keypad acts as three separate transponders and programming them requires a little more of a procedure. To program the various transponders with the SimonsVoss software, please follow the procedure described in the following (also see the appropriate SimonsVoss software manual):

1. On the Wireless Keypad, Press the "0" button twice in order to enter the transponder programming mode. Enter the "master PIN ". (you are now ready to program the Keypad) 2. Start the Transponder programming function in the SV software 3. 4. When you are instructed to push the button on the transponder Press the "1" button on the Keypad for transponder #1 Press the "2" button on the Keypad for transponder #2 Press the "3" button on the Keypad for transponder #3 Please check in the user interface to see that the programming was successful (yellow programmer flash must have been removed in the display). 5. In order to be able to carry out the programming without problems, please first start the programming command in the SV software and only then select the required transponder using the Keypad. Otherwise it is not possible to guarantee successful programming. The Keypad's three integrated transponders must be located in the same lock plan as the lock that you wish to address. It is not possible to enter programming mode when there is a battery warning. This means that it is not possible to change or delete transponders when there is a weak battery. Programming mode will only be available again after you have successfully changed the battery (see the section "Battery Replacement). Wireless Keypad: TRA.PINCODE Page 11 Input "00"

Input "master PIN Start Transponder programming function in the SV software!!!

Procedure 1. 2. Procedure 6.3 7.1 7.2 Transponder 1 =

press "1" button Transponder 2 =

press "2" button Transponder 3 =

press "3" button 7.0 Reading Transponders You can use the SimonsVoss software and configuration tool to examine the transponders integrated in the Keypad. Description To examine the Keypad programming, proceed as follows:

Start the "Read Transponder" function in the software For the specific transponder:

Transponder 1 = enter "PIN 1"

Transponder 2 = enter "PIN 2"

Transponder 3 = enter "PIN 3"

Start the "Read out transponder"

function in the SV software Input "PIN 1"

Input "PIN 2"

Input "PIN 3"

Wireless Keypad: TRA.PINCODE Page 12 8.0 Resetting Transponders 8.1 Description To reset the transponders integrated in the Keypad, please proceed as follows:

1. 2. 3. 4. Press the "0" button twice. Enter the master PIN. Start the Reset Transponder" function n the SimonsVoss software. For the specific transponder :

Transponder 1 = press "1" button, Transponder 2 = press "2" button Transponder 3 = press "3" button It is not possible to enter programming mode when there is a battery warning. This means transponder. Programming mode will only be available again after you have successfully changed the battery (see the section "Battery Replacement). is weak, you cannot reset a the battery that when 8.2 Procedure Input "master PIN Function: Start "Reset transponder" in the Start the "Reset transponder" function in the SV Input "00"

Input "00"

SV LDB software Trans-

ponder 2 =

Transponder 1 =

press "1" button Transpond er 3

Transponder 2 =

press "2" button Transponder 3 =

press "3" button Wireless Keypad: TRA.PINCODE Page 13 9.0 Opening In order to use the Wireless Keypad to open the appropriate lock, proceed as follows:

Enter a PIN that has already been programmed. You are not permitted to wait more than 5 seconds between the entries of the individual numbers. If you have entered the correct number and the integrated transponder has been programmed, the LED lights GREEN and a signal is sounded. Then the integrated transponder opens the lock. 10.0 Meaning of the LED The built-in LED can light in one of three colors: green, yellow or red. These colors have the following meanings:

Green Digit that was input has been accepted PIN input was OK, which means that the correct PIN has been Yellow Red recognized and an open signal is being sent PIN length OK PIN programming procedure was successful Battery warning PIN input was incorrect Input of master code was incorrect Repeated incorrect input of the PIN (manipulation) PIN length was not entered correctly. Wireless Keypad: TRA.PINCODE Page 14 11.0 Battery Warning 12.0 Battery Replacement To minimize operating errors the Wireless Keypad follows a multi-level battery warning system. When the battery capacity begins to drop, you will be notified of this in plenty of time to allow you to replace the batteries. Battery warning level 1: The opening procedure is carried out after a delay. The diode blinks YELLOW and the buzzer sounds for 10 seconds. The Keypad does not send the open command until after these 10 seconds. Battery warning level 2: In this case, the opening procedure is again carried out after a delay. The diode blinks YELLOW and the buzzer now sounds for 20 seconds. The Keypad does not send the open command until after these 20 seconds. You should not wait any longer to replace the battery. Otherwise, the Keypad will stop functioning after a short time. Failure of the Keypad does not prevent the lock from being opened with other transponders. In general, the batteries must be replaced by trained experts only. To do this, proceed as follows:

1. 2. 3. 4. 5. 6. 7. 8. Completely unscrew the two screws in the bottom of the housing. Remove the front of the housing. Carefully release the battery clip from the printed circuit board (Figure 1). Remove both batteries (Figure 1). Insert the new batteries; the positive pole must be pointing up (Figure 2). Carefully hook the battery clip back into the printed circuit board (Figure 3). Put the housing back on. Screw the two housing screws back into the housing from below. After you have replaced the batteries, all functions will be available again. Always replace both batteries at the same time, because they have been charged to approximately the same level. Wireless Keypad: TRA.PINCODE Page 15 When replacing the batteries, be absolutely sure that no water is allowed to penetrate into the housing and that the electronics do not come into contact with water. If necessary, carefully wipe dry the housing section that is attached to the wall.

(figure 2)

(figure 1)

(figure 3) Wireless Keypad: TRA.PINCODE Page 16 13.0 Special Functions 13.1 Hidden Lock for SimonsVoss VdS Shuntlock 3066 The Wireless Keypad can be used for activating SimonsVoss activation units (VdS Shuntlock 3066). This is done by mounting the Keypad within the transmitting range of the activation unit. After you have input the correct PIN, the activation unit is addressed and the alarm system is activated or deactivated via the shuntlock. This allows the requirements of VdS Class C up to SG 6 to be fulfilled by including a hidden lock. The VdS-certified activation units from SimonsVoss need a doubled opening protocol for activation/deactivation procedures (double-click when the transponder should activate or deactivate the system). The following explains the configuration of the Wireless Keypad in order to have it emulate the "double-click" and consequently be suitable for carrying out activation or deactivation procedures. 1. 2. 3. Press the "0" button three times. Input the master PIN. Then press:

either "91" for normal operation (default setting) or "92" for a double-click for shuntlock operation. Input "000"

Input "master PIN"

If the input was correct, the Wireless Keypad stores the change and gives a positive acknowledgement (LED and buzzer). Input "91" (nor-

mal operation)

(shuntlock opera-

Input "92"

tion) Wireless Keypad: TRA.PINCODE Page 17 Important: Please set the two-time opening protocol (double-click) only when you are using a SimonsVoss VdS Shuntlock 3066. Otherwise, there may be malfunctions or unwanted side effects. You can switch from one configuration to the other at any time. It is not possible to enter programming mode when there is a battery warning. This means that when the battery is weak, you cannot change or delete any functions. Programming mode will only be available again after you have successfully changed the battery (see the section "Battery Replacement). 13.2 Miscellaneous The quasi-proximity and validity and expiry mode functions are not available with the Wireless Keypad. 14.0 Technical Specification Dimensions W x H x D Weight Material Color Maximum number of operations with one battery set Operating distance from SimonsVoss lock Operating distance from SmartRelay 3.8 in x 3.8 in x 0.5 in 96 mm x 96 mm x 14 mm 3.3 oz (102 g) including batteries Plastic Grey with transparent ring Approx. 100,000 operations or 10 years on standby Up to a max. of 16 inches (40 cm) when the transponder antenna is parallel to the cylinder antenna Up to a max. of 47 inches (120 cm) when the transponder antenna is parallel to the SmartRelay antenna IP 65 NEMA 12 Protection class Working temperature range -4F to 122F (-20C to 50C) noncondensing Battery type 2 x 3 V DC lithium battery type CR2032