WLAN+BLE Module MODEL :
Quick Installation Guide Installation steps I. WLAN 1. First, install Murara Wireless+BLE combo Driver of EVM Board. 2. Make "RCT" folder in a root directory of the micro SD card. 3. Make "WlanTest.txt" file in the RCT folder.
(WLAN continuous transmission/receiving mode) 4. Insert MICRO SD CARD into EVM Board 5. Click the Power key, wait for 5 seconds entry test mode. BLE 1. First, install Murara Wireless+BLE combo Driver of EVM Board. 2. Make "RCT" folder in a root directory of the micro SD card. 3. Make " BTTest.txt" file in the RCT folde.
(Bluetooth Low Energy continuous transmission/receiving mode) 4. Insert MICRO SD CARD into EVM Board 5. Click the Power key, wait for 5 seconds entry test mode. Power Key II. DC/RF Characteristics Supply Voltage Storage Temperature Supply Voltage VBA VDDIO
-40~+85 degree C DC 3.3V from host DC 3.3V from host DC/RF Characteristics for IEEE802.11 b/g/n Specification Data rate Output Power Operating Channel IEEE 802.11b, DSSS/CCKup to, 11Mbps Max 19 dBm DC/RF Characteristics for Bluetooth(LE) items Bluetooth specification (power class) Channel frequency (spacing) Number of RF Channel Item / Condition Center Frequency Channel Spacing Number of RF channel Output power III. Antenna Information Antenna NO. Brand Model IEEE 802.11g, IEEE 802.11n, OFDMup to 54Mbps OFDMup to 65Mbps Max 23 dBm CH1~CH11 Max 23 dBm Contents Version 4.1(LE) 2402 to 2480 MHz (2MHz) 40 Min 2402
-
-
-
Typ
-
2 40
-
Max 2480
-
-
8 unit MHz MHz
-
dBm 1 2 Walsin RFANT5220110A0T Walsin RFPCA280815EMAB301 2.66 1.17 2.4~2.4835GHz 2.4~2.4835GHz PCB Antenna Net Gain(dBi) Frequency range Antenna Type Monopole Antenna)
(Chip Connecter Type N/A I-PEX Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: Contains FCC ID: SER1DX. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module) 1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: Contains IC: 11195A-1DX. Plaque signaltique du produit final L'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC:
11195A-1DX". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. This radio transmitter (IC: 11195A- 1DX / Model: 1DX) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 11195A- 1DX / Model: 1DX) a t approuv par ISED pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Approved antenna(s) list Type Monopole
(Chip Antenna) Gain 2.66dBi Brand Walsin PCB 1.17dBi Walsin Manufacturer Walsin Technology Corporation Walsin Technology Corporation