comply with IC CAUTION This device contains licence-exempt transmitter(s)/receiver(s) that Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ce matriel est conforme aux limites de dose d'exposition aux rayonnements autre environnement.cet metteur ne doit pas tre situes ou oprant conjointement avec toute autre antenne ou l'metteur. nonces pour rss-102 un ic FCC STATEMENT Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Compliance Statement available in the phone app at:
Settings > Legal & Compliance > Compliance 45 mm LVD01 & LDC01 Video Doorbell Doorbell is the rst entrance of the security around your property. It can see any person at your door or prevent crime wherever you go. Items Included LVD01 LDC01 Video Doorbell Chime Wall bracket Wall Anchors Screws Screw Driver 135 mm Get to know your Video Doorbell and Chime Install your Video Doorbell Setup your Video Doorbell and Chime 1 2 3 4 5 6 7 8 9 10 11 1. Camera lens 2. Microphone 3. Light sensor 4. Doorbell 5. Sensor 6. Speaker 7. SET key 8. Micro USB plug 9. LED indicator 10. Set button 11. Speaker Open the APP to add camera. Press and hold the SET button until LED light blinks to enter the setup mode. Following camera voice navigation to finish the setup. 1. 2. 3. Drill holes for wall anchor placements Insert wall anchors Mount wall bracket with screws Charge your Video Doorbell Pairing your Video Doorbell 4. Place the doorbell on bracket. 5. Tighten the lock screw with cross screw drive Open the back cover, plug in micro usb cable to charge the camera. Press and hold the Set button until LED light blinks Press doorbell button to pair with chime 6. Place the adhesive tape to the back of the chime and stick to the wall in a suitable location inside your home 7 8 m m