TM INSTRUCTIONS LINKABLE SOLAR LED PATHWAY LIGHT ITEM: Q01DA0442-08 FOR FIRST TIME USE: SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 -12 HOURS WITH THE SWITCH IN THE ON POSITION TO FULLY CHARGE THE RECHARGEABLE BATTERY. IF INSTALLING MORE THAN 1 LIGHT, YOU MUST LINK YOUR LIGHTS FIRST BEFORE INSTALLATION BEGINS. YOU MAY LINK UP TO 20 LIGHTS. AFTER THE LIGHTS ARE LINKED YOU MAY BEGIN THE INSTALLATION PROCESS. The intelligent solar LED motion activated light measures the corresponding available battery power through the current voltage point of the battery, adjusts the energy and lumen output, and maximizes the lighting time. Tools Required INSTALLATION Hardware Included
(A) Screw X 2
(B) Wall Anchor X 2 Parts
(C) Light Fixture X 1 5.73in. x x B A A C REPLACING THE BATTERY Pencil Phillips-head Screwdriver Electric drill drill bit size:
7.5mm (3/10 in.) 1 Marking the location Mark the location where you want to mount the light xture (Part C). Measure the width of two holes on the back of the solar fence light to align holes for the 2 screws (Part A) on the surface. The distance between the two holes is 5.73in. (145.5mm). Drill two holes. 2 Mounting the light Insert the wall anchors (Part B) so they are ush with the surface. Insert the screws (Part A) and leave at least 1/4in. (6.3mm) of the screws (Part A) outside of the surface for holding the solar fence light. Mount the light on the screws (Part A) by placing the keyholes on the back of the light over the screw heads. TROUBLE SHOOTING If the light does not turn on, remove the battery cover and check if the battery pack is connected to the battery connector. If the connection is ok, replace the battery with a new one. Slide the power switch to the "OFF" position. Use a Phillips head screwdriver to remove the 5 screws holding the battery cover in place. Gently pull battery pack away from the light xture and disconnect the battery connector. Replace old battery pack with a new 3.7V, 2400 mAh lithium (18650) rechargeable battery pack. Connect the battery connector and insert battery pack into the light xture. Replace the battery cover by aligning it properly and replacing the 5 screws removed earlier. Slide the power switch to the ON position. For optimal performance, allow light xture to charge in direct sunlight for 8-12 hours to fully charge the battery. Screws Power switch Battery Cover Battery pack Battery connector WARNING: Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
Wal-Mart Stores, Inc. Hyper Tough is a registered trademark of Wal-Mart Stores, Inc. All Rights Reserved. Distributed by/Distribuido por Wal-Mart Stores, Inc., Bentonville, AR MADE IN COUNTRY/HECHO EN COUNTRY For assistance with assembly or instruction, parts and customer service, call: U.S.A. & Canada only: 1-844-551-0680 8am 5pm Monday Friday, Central Standard Time Or email: Customerservice@qx-usa.com 10/22/2019 1/2E TM LINKABLE SET-UP INSTRUCTIONS LINKABLE SOLAR LED PATHWAY LIGHT ITEM: Q01DA0442-08 1) 2) Make sure the LED lights are directed away from your eyes then move the power switch to the ON position. Among all the lights, select one as the parent light (PL), and the others as the children lights (CL).
(D) Power switch
(E) Link on button 3) (CL): Move the link button (Part E) to the LINK ON position (direction of arrow) on all children lights (CL) you want to connect to the parent light (PL). Keep in the LINK ON position for one second, then switch the link button (Part E) back to its initial position quickly. The (CL) will start ashing every second, now they are in link mode. All (CL) after complete step 3) operation, time to place the (PL) in link mode. 4) (PL): Move the link button (Part E) to the LINK ON position (direction of arrow). Keep in the LINK ON position for 5 seconds, then the parent light (PL) will ash very slowly
(ashing every 4 seconds). The(PL) is now in link mode and sending signals to pair with the selected (CL). 5) Once the (CL) in link mode receives and saves the paired ID code signal transmitted by the (PL), completes and exits the pairing mode. The blinking light(s) will stop
ashing and resumes normal use. Make sure that all (CL) pairs are completed. 6) (PL): Move the link button (Part E) for parent light (PL) back to its initial position. The blinking light(s) will stop ashing and resumes normal use. Now the (PL) is linked with the (CL), the linking process is complete. When any of the lights (PL) or (CL) are triggered by motion, all lights will activate. Note: Light will stay on 30 seconds when triggered by motion. Detection range is 19.69-26.2 ft (6-8m), detection angle is 120. Light use radio frequency technology to link, and should not be greater than 49.2 ft (15m) between the neighboring/adjacent lights. If you buy a new linkable solar light and want to add it into the family" , you can re-start this LINKABLE SET-UP INSTRUCTION again for all the lights you want to link. If you want one of the (CL) to unpair, turn link button (Part E) to the "LINK ON" position (direction of arrow), stay for more than 5 seconds, the (CL) will ash very slowly (ashing every 4 seconds). then turn back to the original position. Then this (CL) is unpaired. Precautions:
1: The luminaries that are paired with the code are not completed in the normal steps. After the power is turned off, the power is turned on again to resume normal operation. 2: The code switch is mis-operated when the code is not being used. It needs to be powered off again and then powered back on to resume normal operation. FCC WARNING Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. WARNING: Do not dispose of lithium batteries in municipal waste stream or by re as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .
Wal-Mart Stores, Inc. Hyper Tough is a registered trademark of Wal-Mart Stores, Inc. All Rights Reserved. Distributed by/Distribuido por Wal-Mart Stores, Inc., Bentonville, AR MADE IN COUNTRY/HECHO EN COUNTRY For assistance with assembly or instruction, parts and customer service, call: U.S.A. & Canada only: 1-844-551-0680 8am 5pm Monday Friday, Central Standard Time Or email: Customerservice@qx-usa.com 10/22/2019 2/2E TM INSTRUCCIONES LINKABLE SOLAR LED PATHWAY LIGHT ITEM: Q01DA0442-08 PARA EL PRIMER USO: LA LUZ SOLAR NECESITA CARGARSE BAJO LUZ SOLAR DIRECTA POR UN PERIODO DE ENTRE 8 Y 12 HORAS CON EL INTERRUPTOR EN LA POSICIN "ON" (PRENDIDO) PARA CARGAR TOTALMENTE LA BATERA RECARGABLE. SI INSTALA MS DE 1 LUZ, DEBE ACOPLAR SUS LUCES ANTES DE EMPEZAR LA INSTALACIN. PUEDE VINCULAR HASTA 20 LUCES. DESPUS DE ACOPLAR LAS LUCES, PUEDE COMENZAR EL PROCESO DE INSTALACIN. La luz inteligente activada por movimiento del LED solar mide la energa de la batera disponible correspondiente a travs del punto de voltaje actual de la batera, ajusta la energa y la salida de luz y maximiza el tiempo de iluminacin. Herramientas Necesarias INSTALACIN Herrajes Incluidos
(A) Tornillo X 2
(B) Anclajes de pared X 2
(C) Lmpara X 1 5.73in. x x Taladro elctrico tamao de la broca de taladro: 7.5 mm (3/10 plg) Partes Lpiz Cabeza de Phillips Destornillador 1 Cmo marcar el lugar de montaje Marque el lugar en el que quiere montar el artefacto de iluminacin
(Parte C). Mide el ancho de los dos oricios que estn en la parte posterior de la lmpara solar para cerca para alinearlos con 2 tornillos (Parte A) en la supercie. La distancia entre los oricios es de 5.73in. (145.5mm). Taladre dos oricios. 2 Cmo montar la lmpara Inserta los anclajes de pared (Parte B) de manera que queden al ras de la supercie. Inserta los tornillos (Parte A) y deja al menos 1/4in. (6.3mm) de los tornillos (Parte A) afuera de la supercie para sostener la lmpara solar para cerca. Monta la lmpara en los tornillos (Parte A) al colocarlos oricios de la parte posterior de la lmpara en las cabezas de los tornillos. SOLUCIN DE PROBLEMAS Si la luz no se enciende, retire la tapa de la batera y revise si si la batera est conectada al conector de la batera. Si la conexin es correcta, cambie la batera por una nueva. B A A C CAMBIANDO LA BATERA Deslice el interruptor a su posicin de "OFF" (apagado). Use un destornillador Phillips (estrella) para retirar los 5 tornillos que sostienen la tapa de las bateras. Retire con cuidado el paquete de bateras de la lmpara y desconecte el conector de las bateras. Reemplace la batera antigua con una nueva batera recargable de litio (18650) de 3.7V, 2400 mAh. Conecte el conector de bateras e inserte el paquete de baterasen la lmpara. Vuelva a colocar la tapa de las bateras alinendola adecuadamente y vuelva a colocar los 5 tornillos que retir anteriormente. Deslice el interruptor a su posicin de "ON" (prendido). Para un rendimiento ptimo, permita que la lmpara se cargue bajo la luz solar directa durante 8-12 horas para cargar completamente la batera. Tornillos Interruptor de encendido Tapa de las bateras Paquete de bateras Conector de las bateras CUIDADO: No deseche las bateras de litio en la corriente de desechos municipales o por el fuego, ya que las bateras pueden explotar. No abra, provoque cortocircuitos ni mutile las bateras. Deseche las bateras de acuerdo con los reglamentos locales, estatales y federales. No mezcle las bateras viejas con las nuevas. No mezcle las bateras alcalinas, estndar (carbono-zinc) ni recargables (nquel-cadmio, nquel e hidruro metlico o ion litio).
Wal-Mart Stores, Inc. Hyper Tough is a registered trademark of Wal-Mart Stores, Inc. All Rights Reserved. Distributed by/Distribuido por Wal-Mart Stores, Inc., Bentonville, AR MADE IN COUNTRY/HECHO EN COUNTRY Para recibir asistencia con el montaje o las instrucciones, repuestos y servicio al cliente, llame a: (solo EE.UU. y Canad) 1-844-551-0680 de 8am 5pm de lunes a viernes, hora estndar central O enve un correo electrnico a: Customerservice@qx-usa.com 10/22/2019 1/2S TM INSTRUCCIONES DE ACOPLAMIENTO LINKABLE SOLAR LED PATHWAY LIGHT ITEM: Q01DA0442-08
(E) Botn de vinculacin
(D) Interruptor de encendido 1) Asegrese de que las luces LED no estn apuntando hacia sus ojos y lleve el interruptor de encendido a la posicin de "ENCENDIDO". 2) Entre todas las luces, seleccione una como la luz principal (PL) y las otras como las luces dependientes (CL). 3) (CL): Lleve el botn de vinculacin (Parte E) a la posicin de "LINK ON"
(en la direccin indicada por la echa) en todas las luces dependientes (CL) que desee vincular con la luz principal (PL). Mantngalo en la posicin de
"LINK ON" durante un segundo, luego regrese el botn de vinculacin
(Parte E) a su posicin original rpidamente. Las (CL) comenzarn a parpadear a cada segundo, indicando que ya estn en modo de vinculacin. Todo (CL) despus de completar el paso 3) operacin, es hora de colocar la (PL) en modo de vinculacin. 4) (PL): Lleve el botn de vinculacin (Parte E) a la posicin de "LINK ON"
(en la direccin que indica la echa). Mantenga en la posicin de "LINK ON"
durante 5 segundos, la luz principal (PL) parpadear muy lentamente
(cada 4 segundos). La (PL) ahora est en modo de vinculacin, enviando seales para ser emparejada con las (CL) seleccionadas. 5) Una vez que (CL) en el modo de enlace recibe y guarda la seal del cdigo de identicacin emparejado transmitida por el (PL), completa y sale del modo de emparejamiento. Las luces parpadeantes dejarn de parpadear y reanudarn su uso normal. Asegrese de que todos los pares (CL) estn completos. 6) (PL): Vuelva a llevar el botn de vinculacin (Parte E) para la luz principal (PL) a su posicin original. Las luce(s) parpadeantes dejarn de parpadear y reanudarn su uso normal.Ahora la (PL) est vinculada con las (CL), el proceso de vinculacin est completo. Cuando cualquiera de las luces (PL) o (CL) sean activadas por algn movimiento, todas las luces se activarn. Nota: cuando la luz se active con un movimiento, permanecer encendida durante 30 segundos. El rango de deteccin es de 19.69-26.2 pies
(unos 6-8 metros), el ngulo de deteccin es de 120 . La luz utiliza la tecnologa de radiofrecuencia para la vinculacin, por lo cual no debe haber ms de 49.2 pies (unos 15 metros) entre luces adyacentes. Si compra una nueva lmpara solar vinculable y desea agregarla a la "familia", puede realizar nuevamente este PROCEDIMIENTO DE CONFIGURACIN DE LA VINCULACIN desde cero para todas las luces que desee vincular. Si desea desvincular una de las (CL), gire el botn de vinculacin (Parte E) a la posicin de "LINK ON" (en la direccin que indica la echa), mantenga por ms de 5 segundos y luego vulvalo a la posicin original. Dicha (CL) habr quedado desvinculada. Precauciones:
1: Las luminarias que estn emparejadas con el cdigo no se completan en los pasos normales. Una vez que se apaga la alimentacin, se vuelve a encender para reanudar el funcionamiento normal. 2: El interruptor de cdigo no funciona correctamente cuando el cdigo no se est utilizando. Debe volver a apagarse y volver a encenderse para reanudar el funcionamiento normal. ADVERTENCIA DE LA FCC Advertencia: los cambios o modicaciones a esta unidad no aprobados expresamente por la parte responsable del cumplimiento pueden anular la autorizacin del usuario para operar el equipo. Notas: Este equipo ha sido probado y cumple con los lmites para un dispositivo digital de Clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Estos limits estn diseados para la proteccin contra interferencias dainas en una instalacin residencial. Este equipo genera, utiliza y puede irradiar energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia perjudicial a la comunicaciones de radio. Sin embargo, no hay garanta de que no se produzcan interferencias en una instalacin en particular. Si este equipo causa interferencia perjudiciales a la recepcin de radio o televisin, lo cual puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o ms de las siguientes medidas:
Reorientar o reubicar la antena receptora. Aumente la separacin entre el equipo y el receptor. Conecte el equipo a una toma de corriente en un circuito distinto al que est conectado el receptor. Consulte con el distribuidor o un tcnico de radio / TV con experiencia para obtener ayuda. CUIDADO: No deseche las bateras de litio en la corriente de desechos municipales o por el fuego, ya que las bateras pueden explotar. No abra, provoque cortocircuitos ni mutile las bateras. Deseche las bateras de acuerdo con los reglamentos locales, estatales y federales. No mezcle las bateras viejas con las nuevas. No mezcle las bateras alcalinas, estndar (carbono-zinc) ni recargables (nquel-cadmio, nquel e hidruro metlico o ion litio).
Wal-Mart Stores, Inc. Hyper Tough is a registered trademark of Wal-Mart Stores, Inc. All Rights Reserved. Distributed by/Distribuido por Wal-Mart Stores, Inc., Bentonville, AR MADE IN COUNTRY/HECHO EN COUNTRY Para recibir asistencia con el montaje o las instrucciones, repuestos y servicio al cliente, llame a: (solo EE.UU. y Canad) 1-844-551-0680 de 8am 5pm de lunes a viernes, hora estndar central O enve un correo electrnico a: Customerservice@qx-usa.com 10/22/2019 2/2S