FCC ID: REY-WIFIMODULE WiFi Module

Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTES FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Co-location warning:

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Limited Channels fixed for use in the US:

IEEE 802.11b or 802.11g or 802.11n(HT20) operation of this product in the U.S. is firmware-limited to Channel 1 through 11, whereas IEEE 802.11n(HT40) operation limited to Channel 3 through 9. Integrating this module in a host device / OEM integration instructions:

This device is intended only for OEM integrators under the following conditions:

1). The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the integrated on-board antenna as originally tested and certified with this module. As long as these two integration instructions are met, further tests on this modular transmitter will not be required. However, the OEM integrator is still responsible for testing the end-product for any additional compliance requirements required with this module installed (for example, rule part 15B digital device emissions, PC peripheral requirements, RF exposure requirements on host level when located with other transmitters in the same device, etc.) Validity of using the module certification:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a additional FCC authorization. End product labeling:

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: REY-WIFIMODULE. Information that must be placed in the end user manual:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warnings as show in this manual.

Wifi Module Instruction 1. General Instruction It is a device used to set, operate and monitor SKYRC ESC and charger via smart phone. 2. Connectors 1).3Pin connector for ESC 2).Micro USB for charger The power source of the Wifi Module will be the ESC or charger. 3. Apps Application 1).ESC Link for ESC 2).Charger Link for charger 4. Connection Connect ESC/Charger. the ESC/Charger as following, and power on the 5. Getting started 1).When the module is powered on, the power LED will light. The wifi status LED will start to blink when it is building the internet. When the wifi status LED stays on, it is ready to work. 2).The default mode is AP mode and the SSID is SkyRCXXXX. XXXX are the last 4 numbers of MAC. The password is 12341234 3).Start APPS then it is ready to test. 4). User could change the name and password of the module. 5). User could join other internet via Apps. 6). Factory default setting: Press and hold the RESTORE button until the power LED extinguishes. When the power LED is light again, the factory default setting is restored successfully. And user could go back to step 2.