FCC ID: 2AJAC-T5IW Home Automation Control Panel

Regulatory Compliance & Safety Information for Model C4-T5IW8, C4-T5IW11 Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. Lisez ces instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings. Respectez tous les avertissements. 4. Follow all instructions. Suivez toutes les instructions. 5. Do not use this apparatus near water. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Only use attachments/accessories specified by the manufacturer. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 10. Rack Mount Instruction A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com B) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of airflow required for the safe operation of the equipment is not compromised. C) Mechanical Loading- Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. D) Circuit Overloading

- Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E) Reliable Earthing

- Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit

(e.g. use of power strips). Instructions de montage en rack A) Ambiance de fonctionnement leve

- En cas d'installation dans un rack ferm ou plusieurs units, la temprature ambiante de fonctionnement de l'environnement du rack peut tre suprieure la temprature ambiante de la pice. Par consquent, il convient d'envisager d'installer l'quipement dans un environnement compatible avec la temprature ambiante maximale (Tma) spcifie par le fabricant. B) Dbit d'air rduit

- L'installation de l'quipement dans un rack doit tre telle que la quantit d'air ncessaire au fonctionnement sr de l'quipement ne soit pas compromise. C) Chargement mcanique

- Le montage de l'quipement dans le rack doit tre tel qu'une condition dangereuse ne soit pas atteinte en raison d'une charge mcanique ingale. D) Surcharge du circuit

- Il faut tenir compte de la connexion de l'quipement au circuit d'alimentation et de l'effet que la surcharge des circuits pourrait avoir sur la protection contre les surintensits et le cblage d'alimentation. Une considration approprie des caractristiques nominales de l'quipement doit tre utilise pour rpondre cette proccupation. E) Mise la terre fiable

- Une mise la terre fiable des quipements monts en rack doit tre maintenue. Une 11. Wall Mounting Important! Do not mount over 6 ft high (2 m). Important! Mount the bracket with the tabs on the bottom (opening to the top) so the controller will not fall out of the bracket. Montage mural Important ! Ne pas monter plus de 6 pieds (2 m) de haut. Important! Montez le support avec les languettes en bas (ouverture vers le haut) afin que le contrleur ne tombe pas du support. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 14. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Unplug this apparatus during lightning storms or when unused for long periods of time. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 16. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com 18. WARNING Power Sources, Grounding, Polarization This product requires a properly grounded outlet for safety. This plug is designed to be inserted into a NEMA 5-15 (three-prong grounded) outlet only. Do not force the plug into an outlet that is not designed to accept it. Never dismantle the plug or alter the power cord, and do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. If you have a question about grounding, consult your local power company or qualified electrician. If a rooftop device such as a satellite dish connect to the product, ensure that the devices wires are also properly grounded. The bonding point can be used to provide a common ground to other equipment. This bonding point can accommodate minimum 14 AWG wire and should be connected using the required hardware specified by the other bonding point. Please use termination for your equipment in accordance with the applicable local agency requirements. AVERTISSEMENT - Sources d'alimentation, mise la terre, polarisation Ce produit ncessite une prise correctement mise la terre pour des raisons de scurit. Cette fiche est conue pour tre insre dans une prise NEMA 5-15 (trois broches mise la terre) uniquement. Ne forcez pas la fiche dans une prise qui n'est pas conue pour l'accepter. Ne dmontez jamais la fiche ou ne modifiez pas le cordon d'alimentation, et n'essayez pas de dsactiver la fonction de mise la terre en utilisant un adaptateur 3 2 broches. Si vous avez une question sur la mise la terre, consultez votre compagnie d'lectricit locale ou un lectricien qualifi. Si un appareil sur le toit tel qu'une antenne parabolique se connecte au produit, assurez-

vous que les fils des appareils sont galement correctement mis la terre. Le point de liaison peut tre utilis pour fournir une masse commune d'autres quipements. Ce point de connexion peut accueillir un fil de 12 AWG minimum et doit tre connect l'aide du matriel requis spcifi par l'autre point de connexion. Veuillez utiliser une terminaison pour votre quipement conformment aux exigences des agences locales applicables. 19. Notice For indoor use only, Internal components are not sealed from the environment. The device can only be used in a fixed location such as a telecommunication center, or a dedicated computer room. When you install the device, ensure that the protective earthing connection of the socket-outlet is verified by a skilled person. Suitable for installation in information technology rooms in accordance with Article 645 of the National Electrical Code and NFP 75. Avis Pour une utilisation en intrieur uniquement, les composants internes ne sont pas scells de l'environnement. L'appareil ne peut tre utilis que dans un lieu fixe tel qu'un centre de tlcommunication, ou une salle informatique ddie. Lors de l'installation de l'appareil, assurez-vous que la mise la terre de protection de la prise de courant est vrifie par une personne qualifie. Convient pour une installation dans des salles informatiques conformment l'article 645 du Code national de l'lectricit et NFP 75. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers, and microwave ovens if placed in close proximity. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. 21. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com 22. WARNING No user serviceable parts inside. If the product is not operating properly, do not remove any part of the unit (cover, etc.) for repair. Unplug the unit and consult the warranty section of the owners manual. AVERTISSEMENT Aucune pice rparable par l'utilisateur l'intrieur. Si le produit ne fonctionne pas correctement, ne retirez aucune pice de l'appareil (couvercle, etc.) pour rparation. Dbranchez l'appareil et consultez la section de garantie du manuel du propritaire. 23. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 24. PoE considered a Network Environment 0 per IEC TR62101, and thus the interconnected ITE circuits may be considered ES1. The installation instructions clearly state that the ITE is to be connected only to PoE networks without routing to the outside plant. PoE considr comme un environnement de rseau 0 selon IEC TR62101 et, par consquent, les circuits ITE interconnects peuvent tre considrs comme ES1. Les instructions d'installation indiquent clairement que l'ITE doit tre connect uniquement aux rseaux PoE sans acheminement vers l'installation externe. 25. CAUTION: The Optical Transceiver used with this product should use UL listed, and Rated Laser Class I, 3.3 Vdc. ATTENTION: L'metteur-rcepteur optique utilis avec ce produit doit utiliser la liste UL et la classe de laser nominale I, 3,3 Vcc. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B & ISED Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Canada Warning Statement:

CAN ICES-003 (B)/NMB-003(B) This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit rpond aux spcifications techniques applicables l'innovation, Science et Dveloppement conomique Canada. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Canada ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

Lappareil ne doit pas produire de brouillage; Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: 2AJAC-T5IW IC: 7848A-T5IW This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com

(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: FCCID$

IC: IC$

Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the regulatory webpage:

This product can be put into service in all of the EU member states, European Free Trade Association

(EFTA) and EU candidate countries without any restriction. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com CZ BG BE IE EE DE HR FR ES CY LT LV HU MT NL RO PT PL SE FI SK NO LI IS RS MK AL DK EL IT LU AT SI UK CH TR The frequency and maximum transmitted power in EU are listed as below:

2412 - 2472 MHz: ?$ dBm 5180 - 5240 MHz: ?$ dBm WLAN 5GHz:

Operations in the 5.15-5.35GHz band are restricted to indoor usage only. United Kingdom (UK) Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the UK Declaration of Conformity (DoC) is available on the regulatory webpage:

Recycling Snap One understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Snap One is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Snap One products, please contact your local Snap One representative or dealer. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com Australia & New Zealand Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. About this Document Copyright 2025 Snap One All rights reserved. 1355 W. Innovation Way, Suite 125 Lehi, UT 84043 adiglobal.com

Table of Contents Introduction Supported models Box contents Accessories available for purchase Warnings Specifications and Requirements Specifications Requirements Front view Back view Top view Touchscreen placement LED indicator Installing the Touchscreen Power and Network Power and network installation options Installing the Touchscreen Mounting Plate Installing the T5 Touchscreen Configuring the Touchscreen Configure the touchscreen for wireless (optional) Configure the touchscreen for Ethernet Add and configure in Composer Pro Troubleshooting Boot up time 3 4 5 5 6 8 8 9 10 12 13 13 14 14 15 18 22 23 23 25 26 27 27 1 Unresponsive screen Removing the touchscreen from the wall Technical support Warranty and legal notices More help 27 28 30 31 31 2 Introduction 3 The Control4 54 Series 8- and 11-inch In-Wall Touchscreens offer complete system control in an elegant and compact design. The touchscreens are equipped with full capacitive touchscreen, audio and video intercom (with built-in camera), facial recognition, proximity sensor, and more. This touchscreen works great in either new construction or retrofit installations. For power and network connectivity, choose from three options:

l Ethernet with PoEThe Ethernet network connection is provided through the PoE injector. No additional wiring is needed. l WiFi with PoEThe internal Wi-Fi communicates with the LANs wireless AP, so no additional network wiring is needed. PoE powers the touchscreen. l WiFi with AC power supplyThe internal Wi-Fi communicats with the LANs wireless AP and an optional AC power supply powers the touchscreen. Note: Note: 802.11b is not recommended for video intercom. We recommend using Wireless-N. See Specifications and Power and Network Installation Options for more information. Supported models C4-T5IW8-WH T5 TOUCHSCREEN IN-WALL 8" WHITE C4-T5IW11-WH T5 TOUCHSCREEN IN-WALL 11" WHITE 4 Box contents l 8" or 11" T5 In-Wall Touchscreen l Wall mounting bracket (to secure touchscreen to junction box) l White swappable trim-ring (pre-installed) l l l Two screws (to attach the power box to the wall box) Set screw (to secure the touchscreen to the power box) (pre-installed, to secure touchscreen to mount bracket) Set screw tool (3/32" straight-shaft hex driver) Accessories available for purchase Optional power supplies:

l l T5 Touchscreen AC Power Supply Adapter (C4-T5IW-AC) Araknis Networks Multi-gig PoE+ injector (AN-POE-INJ-MG-30W) In-wall touchscreen wall box kits - new construction:

l l

*Plastic (C4-NWB57C-P) Metal (C4-NWB57C-M) In-wall touchscreen wall box kits - retrofit:

l l

*Plastic (C4-RWB57C-P) Metal (C4-RWB57C-M) 5 Note: *Plastic wall box kits are not compatible with the AC power supply adapter. For wall box installation details, see:

l l In-Wall Touchscreen Wall Box Installation Guide-New Construction (ctrl4.co/wallbox-

new) In-Wall Touchscreen Wall Box Installation Guide-Retrofit (ctrl4.co/wallbox-retro) Warnings Warning: Do not place the touchscreen near sources of heat or expose to direct sunlight for an extended period of time. AVERTISSEMENT ! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. Warning: Install in accordance with all national, state, and local electrical codes. AVERTISSEMENT ! Installez selon tous les national, tat, et codes lectriques locaux. Warning: Warning! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. AVERTISSEMENT ! Ce produit produit de la chaleur. La salle doit avoir ventilation proportionne ou la capacit dabsorber la chaleur efficacement. 6 Warning: Warning! Use this product only in dry locations. AVERTISSEMENT ! Employez ce produit seulement dans des endroits secs. Caution! Do not use pens or sharp objects to navigate or make selections on the touchscreen. To select an item or scroll through a list, use your fingertip. AVERTISSEMENT ! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. Caution! Improper use or installation can cause DAMAGE OF PROPERTY. AVERTISSEMENT ! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. Note: Important! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. Important ! Utilisant ce produit en quelque sorte autre que dcrit dans ce document vide votre garantie. De plus, Control4 nest pas responsable daucun dommage encouru avec labus de ce produit. Voyez que Warranty. 7 Specifications and Requirements Specifications Model Numbers C4-T5IW11-WH, C4-T5IW8-WH Screen Resolution: 1920 1200, capacitive touch Camera: 720p Ethernet or Wi-Fi 802.11b/g/n 2.4 GHz 802.11a/n/ac 5 GHz Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP Notes: (1) While technically the touchscreen can use 802.11b, 802.11b is Network not supported. (2) 802.11n is recommended for best performance. Even with 802.11n, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. Power supply PoE (IEEE 802.3af) 12 W peak 8 Dimensions (W H D) 8" model: PENDING FROM ENGINEERING 11" model: PENDING FROM ENGINEERING 8" model: PENDING FROM Weight (with mounting ENGINEERING bracket) 11" model: PENDING FROM ENGINEERING Operating temperature 0 to 40 C (32 to 104 F) Storage temperature

-20 to 70 C (-4 to 158 F) Requirements l l l A controller fully installed and configured with Control4 OS 4.1.0 or later. Control4 Touchscreen wall box installed. See Accessories. If using Ethernet with PoE power:

l l l Ethernet network installed and available that includes a gateway/router/switch 20W PoE injector or switch. PoE injector must be UL/ANSI-certified. Two Ethernet Cat 5/6 cables: (1) one that runs from the Ethernet gateway/router/switch to the PoE injector/switch and (2) one that runs from the PoE injector/switch to the Ethernet connection in the touchscreens wall box. l If using Wi-Fi with a PoE injector:

9 l Wireless network (IEEE 802.11a/b/g/n/ac) installed and available with a wireless access point (AP).Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, or PEAP. Front view A Indicator LED (startup, camera in use) 10 B Camera C Proximity Time of Flight Sensor D Far-Field Microphone Array E Swappable trim ring F8" or 11" diagonal, capacitive 1920 x 1200 display G Speakers 11 Back view H PoE Ethernet port I Locking tab insert J Locking screw (secures touchscreen to wall mounting bracket) K AC adapter pins (only used with optional AC power supply adapter) 12 Top view L Locking screw (secures touchscreen to wall mounting bracket) M Reset pinhole - Press to reset, press and hold until "Erasing" appears on screen to restore to factory defaults. Touchscreen placement Place the touchscreen in a convenient location at eye level, typically near the entrance of the room, about 145 to 155 cm (57 to 61 inches) from the floor (Figure 3). Note: Consider the camera on the panel and the height of the people in the home who will use the camera for Video Intercom. Important Important: The top of the touchscreen must be mounted no higher than 2 m

(6.6 ft.) above the floor. Figure 1: Touchscreen placement 13 LED indicator The LED on the touchscreen indicates the camera status of the camera and booting information as described in the next table. Camera/LED color state Off White solid White flashing (1 Hz) White flashing slow (0.5 Hz) Touchscreen status Camera is off Camera is on Touchscreen is booting Factory reset Installing the Touchscreen Power and Network Important ! Before you can complete the instructions below, you must have a Touchscreen wall box installed according to the documentation provided in the wall box kit. See Accessories for details. Important ! Avant de lire les instruction ci-dessous, il vous faut un support mural install suivant la documentation fournie avec le kit du support mural. Plus de dtails dans la partie << Accessoires >>. 14 Important ! When cutting the opening for the wall box, do not cut the opening too large. Be conservative and cautiously enlarge it as needed. Important ! En coupant louverture pour le support mural, ne faites pas une ouverture trop grande. Soyez prudent, et agrandissez la avec prcaution. Power and network installation options This device uses an Ethernet or Wi-Fi network connection and can be powered using PoE. Choose one of the following options to install the power and network communication:

Option 1: Ethernet connection with PoE Power of Ethernet (PoE) supplies DC power on the Ethernet cable using an Araknis Networks Multi-gig PoE+ Injector (AN-POE-INJ-MG-30W) to provide the touchscreen with power and a network connection. The touchscreen works with the Araknis PoE Injector or a third-party PoE Injector. To set up your PoE and Ethernet connection with a PoE Injector:

1. Attach the PoE Injector according to the instructions in the injectors installation guide if provided. 2. Pull the Ethernet cable from that location to where you want to install the touchscreen. 15 Figure 2: Ethernet with PoERequires Ethernet connection to PoE injector Option 2: Wi-Fi with PoE injector A PoE injector supplies DC power to the touchscreen by an Ethernet cable. The touchscreen works with the PoE Injector or any compatible third-party PoE Injector. To set up your Wi-Fi connection and a PoE injector:

1. Attach the PoE Injector according to the instructions in the injectors installation guide, if provided. 2. Pull the Ethernet cable from that location to where you want to install the touchscreen. 16 Figure 2: Ethernet with PoERequires Ethernet connection to PoE injector Option 3: Wi-Fi with AC power To connect AC power:

1. Place the touchscreen above a power source, for example, an outlet. Make sure the location is within distance of your Wi-Fi signal. (Figure 5). Figure 5: AC power with Wi-Fi 17 2. Prepare the AC power adapter for installation into the wall box by inserting the AC power cable into the wall box. Important : Use only 14 AWG wire for AC connections. For supply connections, use wires suitable for at least 60 C (140 F). 3. Pull the power cable through a right-side knockout hole of the wall box. 4. Strip the line (hot) and neutral wire ends to 6 mm (about 1/4), Installing the Touchscreen Mounting Plate The mounting plate is provided to ensure a rigid back plane for plumb and level installs to the wall box and magnetic connections for secure and convenient touchscreen mounting. 18

(Options 1 and 2) Touchscreen installs with PoE power To install the mounting plate for PoE-power touchscreens:

1. Extend Ethernet cable out of wall box approximately 4-6". 2. Insert Ethernet cable through middle hole of mounting plate. 3. Secure mounting plate to wall box with the included screws. 19 Note: Three sets of screws are included with touchscreen. Use "A" or "B"

screws for standard wall boxes. Use "C" screws for Control4-branded back boxes. 20 Note: Install the mounting plate with the directional arrow facing up.

(Option 3) Touchscreen install with AC power supply The Control4 T5 Touchscreen In-Wall AC Power Supply (C4-T5IW-AC, sold separately) can be used to power the T5 touchscreen. To install the T5 touchscreen with the AC power supply:

1. Secure AC power supply adapter to rear of the mounting plate with the 4 included screws. Note: NOTE: AC power supply adapter is directional, install the adapter so that the power pins are on the LEFT side of the mounting plate. The adapter will connect flush up to the back of the mounting plate when it is oriented correctly. 2. Connect the power leads, hot/line and neutral, to the terminals on AC power supply adapter according to local electrical code and regulations. 3. If using a plastic wall box with an exposed bare copper ground, wrap the ground in electrical tape or heat shrink tape/tubing. If using a metal wall box, attach the ground wire to the wall box. 4. Bend wires back into wall box while pressing mounting plate and AC power supply adapter into place. 5. Secure mounting plate to wall box with included screws 21 Note: Three sets of screws are included with the touchscreen. Use "A" & "B"

screws for standard wall boxes. Use screws "C" when using Control4 branded back boxes. Note: Mounting plate is directional, ensure plate is mounted correctly with the up arrow on the front pointing up. Installing the T5 Touchscreen 1. If using POE power, insert Ethernet cable into back to touchscreen. 2. Align touchscreen with mounting plate and press into place. Magnets will assist with alignment. 3. Remove trim ring from touchscreen and tighten the security screw on the top edge of touchscreen. 22 4. Re-install trim ring. Configuring the Touchscreen Configure the touchscreen for wireless (optional) To configure the touchscreen for wireless:

1. After initialization, tap Network. The network configuration page opens. 2. Under Wi-Fi, make sure the Wi-Fi is enabled, then tap the Wi-Fi field to open a list of available networks. 3. Tap the network name you want to connect to. 23 4. Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 5. Tap Connect. If you dont see the network you want:

1. Tap +, then tap the Network SSID field and type the SSID (name) of the network by using the on-screen keyboard. 2. Tap the Security field, then select the type of security to use. 3. Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 4. Tap Save. The new network is added to the bottom of the network list. To set a wireless static IP address:

1. Scroll down and tap Show advanced options. 2. Tap IP settings, then tap Static. 3. Select each box one at a time and use the on-screen keyboard to type the:

l IP address 24 l l l l Gateway Network prefix length DNS 1 (preferred) DNS 2 (alternate) Configure the touchscreen for Ethernet If you want to use DHCP (default) for your Ethernet connection, no further setup is required. To configure a static IP address for Ethernet:

1. After initialization, tap Network. The network configuration page opens. 2. Tap Ethernet. The Ethernet settings screen opens. 3. Tap Static IP Settings, then tap Use static IP. 4. Select each box one at a time and use the on-screen keyboard to type the:

l l l l l IP Address Gateway Netmask DNS 1 (preferred) DNS 2 (alternate). 5. Tap SAVE when finished. 25 Add and configure in Composer Pro After the touchscreen is installed and appears on the home network, use Composer Pro to add it to the Control4 system and configure it. Use the Composer Pro System Design and Connections views to add and configure this device. To add and configure a T5 touchscreen to a project:

1. Add the T5 8/11" In-Wall Touchscreen driver to your project by double-clicking on the device in System Design > Items > Discovered. The touchscreen driver is added and automatically identified into the system. 2. Select the touchscreen or its Intercom component in the project trees System Design view. 3. View and change the properties in the Properties pane as needed. Properties include:

l l l l Network ConnectionReports the touchscreens current network connection type. Back LightUse the arrows or type numbers to set the light level, then click Set. Adaptive Brightness EnabledEnables or disables adaptive brightness. Proximity SensorEnables of disables the proximity sensor. Advanced Properties include:

l l Camera EnabledEnables or disables the camera. RebootRemotely reboots the touchscreen. 26 l Bluetooth Configure bluetooth settings as audio input for Control4 Ryff steaming. l Wake ExperienceConfigure device wake behavior once device is unlocked/woken from sleep/screensaver state. Troubleshooting Boot up time When the device is booting up, it may take 10 seconds before the logo image appears on the screen. When it turns on, you will see an image for a short time, then it will turn off. After that, either the setup menu or the rooms home screen will appear. Unresponsive screen If the logo image does not appear after 30 seconds, the device may need to be power cycled. If power cycling doesnt solve the problem, the touchscreen may need to be restored to factory defaults. To manually power-cycle the touchscreen:

1. Press and hold the power button for at least 10 seconds until the touchscreen turns off. To restore to factory defaults:

1. On the touchscreens main screen, tap Settings, System Info, then Factory data reset.

- OR -

27 1. If the touchscreen has not yet been configured, tap About, then Factory data reset.

- OR -

1. Remove trim ring from touchscreen. 2. Locate pinhole (labeled Reboot/Factory Restore) on top face of touchscreen. Press and hold for 10 seconds to initiate factory restore. Removing the touchscreen from the wall To remove the touchscreen:

28 1. Remove the trim ring and loosen the security screw. 2. Pull the bottom of the touchscreen away from the locking tab, then lift the screen up and off the power box. 29 Technical support For chat and telephone, visit ctrl4.co/techsupport. Email: [email protected] Visit tech.control4.com for discussions, instructional videos, news, and more. 30 Warranty and legal notices Find details of the products Limited Warranty and other resources such as regulatory notices and patent and safety information, at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489. More help For the latest version of this document, open this URL or scan the QR code on a device that can view PDFs. More T5 help and resources Latest version of this document ctrl4.co/t5-inwall-ig ctrl4.co/t5 31 Technical Support For chat and telephone, visit snp1.co/techsupport Email: [email protected]. Visit snp1.co/tc for discussions, instructional videos, news, and more. Warranty and Legal Notices Find details of the products Limited Warranty and other resources such as regulatory notices and patent and safety information, at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489. Copyright2025, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice. 250320 Arena SKU-A 32