FCC ID: 2AGPT-ENET SolarEdge Energy Net

SolarEdge Energy Net Plug-in Installation 1. Install the Antenna To avoid electric shock, refer to safety instructions in inverter manual before removing inverter cover. 1 Turn off inverter and DC safety switch (if applicable). 2 Turn off AC to inverter on main service panel. 3 Wait five minutes. 4 Open inverter and Connection Unit (if applicable) cover. 5MIN 2. Install and Connect the Plug-in OFF

AC OFF ENET-HBNP-01 1 2 1 Connect EnergyNet plug-in to socket on communication board. 2 Connect antenna to EnergyNet plun-in. ENET-HBRP-01 1 2 ENET-HBCL-01 1 2 3 Tie antenna cable to communication board bracket with plastic tie

(supplied). 5 Clip antenna (supplied) to heatsink fin. 6 Pass antenna cable through communication gland. 4 Mount inverter cover and Connection Unit cover (if applicable). Tighten screws to 8.4Nm/74lbin. 3. Verify Connection 1 Run SetApp 2 Scan the QR code on the inverter. 3 Verify connection. Commissioning SetApp Status Communication Energy Net OK Regulatory Statements Professional Installation Instructions Installation Personnel This product is designed for a specific application, and needs to be installed by qualified personnel. The user should not attempt to install the product or change any of the product settings. External Antenna Use only the antennas, which have been approved by the applicant. Unapproved antenna(s) may produce unwanted spurious or excessive RF transmitting power, which may lead to violation of FCC/IC limits and is prohibited. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

This module has been tested for compliance to FCC Part 15 The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. RF Exposure Considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. Approved antenna(s) list:

Manufacturer RALTRON RALTRON SolarEdge SolarEdge Model RST-TUA3-TUB7-320020-17M-A-002 RST-TUA3-TUB7-19550200-17M-A-001 AS4034-1 AS4035-1 Antenna Type Dipole Dipole Dipole Dipole Max Gain (dBi) 3dBi 3dBi 0dBi 0dBi Impedance () 50ohm 50ohm 50ohm 50ohm Label and Compliance Information The final end product must be labeled in a visible area with the following: Contains FCC ID: 2AGPT-ENET. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Information on Test Modes and Additional Testing Requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. Additional Testing, Part 15 Subpart B Disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host Manufacturer Responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment. Industry Canada Statement This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre install et exploit avec plus de 20 cm entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 20916-ENET . Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des 20916-ENET". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Detachable Antenna Usage This radio transmitter [IC: 26049-DLWPH-8M] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 26049-DLWPH-8M] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Approved antenna(s) list:

Manufacturer RALTRON RALTRON SolarEdge SolarEdge Model RST-TUA3-TUB7-320020-17M-A-002 RST-TUA3-TUB7-19550200-17M-A-001 AS4034-1 AS4035-1 Antenna Type Dipole Dipole Dipole Dipole Max Gain (dBi) 3dBi 3dBi 0dBi 0dBi EU Hereby, SolarEdge declares that the radio equipment type ENET is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

Impedance () 50ohm 50ohm 50ohm 50ohm The frequency and maximum transmitted power in EU are listed as bellows:

863876 MHz: 17.00 dBM NCC-1 Warning Statements NCC-2 Warning Statements 1. XXXyyyLPDzzzz-x 2. VCCI Statement

solar ze/e(-"

Label Artwork Model:ENET Gams Baer _FCC ID:2AGPT-ENET

|_IC: 20916- ENET ca rc _CAN ICES-3 (B)/NMB-3(B) |

Made in: MMMMMM Label Location Product/Certification Label wr. eS eee

SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya 4673335, Israel TEL: +972-9-9576620 FAX: +972-9-9576591 Date: 2021-04-18 FCC ID: 2AGPT-ENET A U T H O R I Z A T I O N L E T T E R To Whom It May Concern:

SolarEdge Technologies Ltd. hereby authorizes Andrea Hsia, Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission

(FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia, Supervisor of BV CPS Taoyuan on SolarEdge Technologies Ltd.s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

Oren Bachar, Authorized Signatory SolarEdge Technologies Ltd. Tel: +972-9-9576620 Fax: +972-9-9576591 E-mail: oren.b@solaredge.com

SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya 4673335, Israel TEL: +972-9-9576620 FAX: +972-9-9576591 P R O F E S S I O N A L I N S T A L L A T I O N A T T E S T A T I O N Date: 2021-06-06 FCC ID: 2AGPT-ENET We, SolarEdge Technologies Ltd. hereby declare that requirements of KDB 353028 D01 Antennas Part 15 Transmitters v01 have been met and shown on the following questions. Further we declare that the info listed below are correct and represent the product in consideration under this filing. 1. Professional installation must be justified. Description: Device is sub-GHz transceiver and must need special trained professional in configuring and installing the product, more details please refer to user manual exhibit. 2. Professional installation does not permit use of any antenna with the transmitter; the permitted types of antenna specified as below. Description: Below listed of Antennas has been compliance FCC Rule Part 15 requirement, more details please refer to test reports. 3. The applicant should address the following items when justifying professional installation.

(1) To qualify for professional installation, please explain why the hardware is not readily available to average consumer. Description: Due to this product will not be sold directly to the general public through retail store, therefore the hardware is not readily available to average consumer.

(2) Marketing Applicant must ensure device cannot be sold via retail to the general public or by mail order. Description: This product will not be sold directly to the general public through retail store. It will be sold to authorized dealers or installers only. SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya 4673335, Israel TEL: +972-9-9576620 FAX: +972-9-9576591

(3) Applicant must show that device intended use is not for consumers and general public. Description: The product will not be intended for use by consumers and general public. The product must be installed by a professional with special training

(4) Explain what is unique, sophisticated, complex, or specialized about the equipment that REQUIRES it to be installed by a professional installer?

Description:The sub-GHz transceiver can be matched with different external antennas, different antennas have different settings need to be in installed, and so special person is required in configuring and installing the product. 4. Other professional installation requirements

(1) Installation must be controlled. Description: The product will be distributed through controlled distribution channel which has special trained professional to install this product

(2) Installed by licensed professionals. Description: Device sold to dealer who hires installers and need special trained professional in configuring and installing the product.

(3) Installation requires special training. Description: The product needs special programming, access to keypad, field strength measurements made, so must need special trained professional in configuring and installing the product. If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Oren Bachar, Authorized Signatory SolarEdge Technologies Ltd. Tel: +972-9-9576620 Fax: +972-9-9576591 E-mail: oren.b@solaredge.com

SolarEdge Technologies Ltd. 1 HaMada Street, Herzeliya 4673335, Israel TEL: +972-9-9576620 FAX: +972-9-9576591 Date: 2021-04-18 FCC ID: 2AGPT-ENET To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

Oren Bachar / Certification Engineer Tel: +972-9-9576620 Fax: +972-9-9576591 E-mail: oren.b@solaredge.com

FCC ID: 2AGPT-ENET Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch May 20, 2021 Dear Application Examiner, SolarEdge Technologies Ltd., SolarEdge Energy Net, FCC ID: 2AGPT-ENET would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. The modular transmitter must have its own RF shielding. The radio portion of this module has been shielded, please see exhibition External Photo. 2. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs, it is integrated in chip EFR32XXX. 3. The modular transmitter must have its own power supply regulation. The part number of this regulator is EFR32XXX.. 4. The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C). The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. The modular transmitter must be labeled with its own FCC ID number. Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: 2AGPT-ENET 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Andrea Hsia Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch