SonicWall SonicWave 224w Draft Quick Start Guide Regulatory Model: APL45-0D0 Topics:
Capabilities and Components on page 1 SonicWave 224w Ports and LEDs on page 1 Connecting PoE to the SonicWave 224w on page 3 Installation Safety Requirements on page 4 Capabilities and Components The SonicWall SonicWave 224w is a wallmountable wireless access point suitable for indoor singleunit or multiunit deployments. It provides 2x2 MIMO spatial streams for the 802.11b/g/n/ac radio module, with dual 2.4GHz and 5GHz radios, and four 1GbE LAN ports. It has internal antennas, and is powered with 802.3at compliant PoE. One 1GbE LAN port provides PoE out for an 802.3af device. SonicWave 224w Hardware Components Component 1GbE LAN ports Number or Description 4 Ethernet LAN ports, 10/100/1000 bps USB 2.0 port N/A Radios Bluetooth 2x2 802.11n + 2x2 802.11ac MUMIMO Bluetooth Low Energy (BLE) radio Antenna type Internal Antenna quantity 5 (2.4Ghz x 2 / 5Ghz x 2 / BLE x 1) Power source 802.3at PoE (standard, PoE sold separately) Chassis Rectangle Operating temperature SonicWave 224w Ports and LEDs 0 to 40C The LAN1/POE port is on the back panel of the SonicWave 224w. This is where you connect the access point to the PoE injector or PoEenabled switch. The back panel also has a blue Pass Through port, which is directly connected to the blue Pass Through port on the bottom edge of the unit. Neither of these ports access any functionality in the SonicWave 224w, but allow you to connect to a second network available in the same wall jack that provides your PoEenabled network connection. When the access point is installed, the back panel is attached to the wall. SonicWall SonicWave 224 w Beta Quick Start Guide 1 SonicWave 224w Back Panel The bottom edge provides more ports. The blue Pass Through port is directly connected to the blue Pass Through port on the back panel of the unit, allowing you to connect to a second network available in the same wall jack that provides your PoEenabled network connection. The LAN4/POE OUT port provides PoE out to power an 802.3af device, such as an IP camera. The LAN2 and LAN3 ports provide a way for you to connect directly to the SonicWave 224w over Ethernet for access to the internet or internal networks via the SonicWall firewall that is connected to the SonicWave 224w. SonicWave 224w Ports Along Bottom Edge The side panel of the SonicWave 224w has the LED indicators. SonicWave 224w LEDs SonicWall SonicWave 224 w Beta Quick Start Guide 2 Connecting PoE to the SonicWave 224w The SonicWave 224w is powered through Power over Ethernet (PoE), and should be connected with CAT5e or higher rated Ethernet cabling (max length 100 meters). A multigigabit 802.3at compliant PoE injector or PoEcapable switch is required to provide power to the SonicWave 224w. To connect a PoE injector to the SonicWave 224w:
1 Using an Ethernet cable, connect the Data In port on the SonicWall PoE Injector to an existing WLAN zone interface on the SonicWall firewall or to an unused interface to be configured later in SonicOS. 2 Using a second Ethernet cable, connect the Data and Power Out port on the SonicWall PoE injector to the LAN1/POE IN port on your SonicWave 224w. 3 Plug the power cord of the SonicWall PoE injector into an appropriate power outlet. 4 Wait for the LAN LED on the SonicWave 224w to illuminate. This indicates an active connection SonicWall SonicWave 224 w Beta Quick Start Guide 3 Mounting instructions. Mounting Plate (Direct to wall or junction box) Directly to wall On the wall surface, mark the location to make two screw holes. For drywall use screw in anchors For wood wall screw directly into wall. Make hole in center of plate for Ethernet wires. Junction Box Align holes on mounting plate with junction box. Use pan head screws appropriate junction box. Mounting AP to Bracket Place bracket tab in AP mounting holes and slide AP onto tabs Screw bracket screw into AP. SonicWall SonicWave 224 w Beta Quick Start Guide 4 Installation Safety Requirements The following conditions are required for proper installation:
1 Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104 F (40 C) is recommended. 2 Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers 3 Ensure that no water or excessive moisture can enter the unit. 4 Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended. 5 Consideration must be given to the connection of the equipment to the supply circuit and that the effect of overloading the circuits has minimal impact on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern. 6 This equipment is not intended for use at workplaces with visual display units, in accordance with 2 of the German ordinance for workplaces with visual display units. To avoid incommoding reflections at visual display workplaces, this device must not be placed in the direct field of view. Cable Connections All Ethernet and RS232 (Console) cables are designed for intrabuilding connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the appliance is located. Power Supply Information When this product's power is provided by the Ethernet cable plugged in to the LAN port, this is called Power over Ethernet or PoE. The PoE source should only be UL listed marked Class 2 or LPS with an output rated 48 VDC, minimum 0.6 A, Tma: minimum 40 degrees C. When powering via external power adapter via barrel jack, use only UL Listed power supply marked Class 2 or LPS with output rated 12Vdc, min. 2.0A, Tma: minimum 40 degrees Co. To use PoE output on LAN4 the POE power sourse must be used. POE output can supply power to single 802.3af compliant device, (output is 48 VDC, maximum 0.3 A). SonicWall SonicWave 224 w Beta Quick Start Guide 5 Exigences relatives l'installation AVERTISSEMENT :
Les conditions suivantes sont requises pour une installation correcte :
1. Procdez au montage dans un endroit l'abri des rayons du soleil et des sources de chaleur. Une temperature ambiante maximale de 60 C (140 F) est recommande. 2. Faites passer les cbles une distance raisonnable des lignes lectriques, des luminaires pour lampes fluorescentes et des sources de bruit telles que les radios, les metteurs et les amplificateurs large bande. 3. Veillez viter tout contact de l'appareil avec de l'eau ou une humidit excessive. 4. Veillez ce que l'air puisse circuler librement autour de l'appareil. Laissez un espace d'au moins 25,44 mm. 5. Portez une attention particulire au raccordement de l'quipement au circuit d'alimentation, de manire ce qu'une ventuelle surcharge des circuits ait un impact minime sur la protection contre les surintensits et sur les cbles d'alimentation. Respectez pour cela les mentions figurant sur la plaque d'identification du produit. Raccordements AVERTISSEMENT :
RS232 (console) sont conus pour un raccordement intrabtiment d'autres appareils. Les cbles RS232 (console) sont conus pour un raccordement intrabtiment d'autres appareils. Ne reliez pas ces ports directement des cbles de communication ou d'autres cbles qui sortent du btiment dans lequel se trouve l'appareil. Informations sur l'alimentation lectrique Lorsque ce produit est aliment par le cble Ethernet connect au port "LAN1"; ce type d'alimentation est appel "Power over Ethernet" ou "PoE" (Power over Ethernet). La source d'alimentation par cble Ethernet
(PoE) utilise doit imprativement tre homologue UL, porter la mention Classe 2 ou LPS , et avoir une puissance de sortie nominale de 48 V CC, 0,6 A minimum, TA : 40 C. Lors de l'alimentation via un adaptateur d'alimentation externe via une prise barillet, utilisez uniquement une alimentation homologue UL portant la mention Classe 2 ou LPS avec une sortie nominale de 12 Vcc, min. 2.0A, Tma: minimum 40 degrs C TA : 40 C. Pour utiliser la sortie PoE sur LAN4, vous devez utiliser l'adaptateur POE. La sortie POE peut alimenter un seul appareil compatible 802.3af (la sortie est de 48 VCC, maximum 0,3 A). Anforderungen an die Installation Verwarnung:
Fr eine ordnungsgeme Montage sollten die folgenden Hinweise beachtet werden:
SonicWall SonicWave 224 w Beta Quick Start Guide 6 1. Whlen Sie fr die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der Nhe von Wrmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 60 C betragen. 2. Fhren Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffrhren und Strquellen wie Funksendern oder Breitbandverstrkern. 3. Stellen Sie sicher, dass das Gert vor Wasser und hoher Luftfeuchtigkeit geschtzt ist. 4. Stellen Sie sicher, dass die Luft um das Gert herum zirkulieren kann,. Hier ist ein Belftungsabstand von mindestens 26 mm einzuhalten. 5. Prfen Sie den Anschluss des Gerts an die Stromversorgung, damit der berstromschutz sowie die elektrische Leitung nicht von einer eventuellen berlastung der Stromversorgung beeinflusst werden. Prfen Sie dabei sorgfltig die Angaben auf dem Aufkleber des Gerts. berlasten Sie nicht den Stromkreis. 6. Dieses Gert ist nicht zur Verwendung an Arbeitspltzen mit visuellen Anzeigegerten gem 2 der deutschen Verordnung fr Arbeitspltze mit visuellen Anzeigegerten vorgesehen. Um strende Reflexionen am Bildshirmarbeitsplatz zu vermeiden, darf dieses Produkt nicht im unmittelbaren Gesichtsfeld platziert verden. Verwarnung Kabelverbindungen RS232CKabel eignen sich fr die Verbindung von Gerten in Innenrumen. Schlieen Sie an die Anschlsse der SonicWall keine Kabel an, die aus dem Gebude herausgefhrt werden, in dem sich das Gert befindet. Informationen zur stromversorgung Wenn die Stromversorgung durch das EthernetKabel in die LAN1 Anschluss angeschlossen vorgesehen ist, wird dies als Power over Ethernet oder PoE. Dieses Produkt darf nur in Verbindung mit einem fr den Europischen Markt genehmigten und mit dem Logo LPS. Ausgang: 48 VDC Gleichsspannung, mind. 0,6 A, mindest TMA mindestens 40 Grad C, betrieben werden. Wenn dieses Produkt sollte nur mit einem fr den Europischen Markt genehmigten Netzteil mit dem Logo
"I.T.E. LPS" und einer Ausgangsleistung von12 VDC, mind. 2.0 A, Tma: mind. 40 Grad C, betrieben werden. Um den PoE-Ausgang auf LAN4 zu verwenden, muss der POE Netzadapter verwendet werden. Der POE-
Ausgang kann ein einzelnes 802.3af-kompatibles Gert mit Strom versorgen (Ausgang ist 48 VDC, maximal 0,3 A). SonicWall SonicWave 224 w Beta Quick Start Guide 7 EU and EFTA This SonicWall appliance contains radio equipment to provide 2.4 GHz and 5 GHz RLAN/WLAN. To maintain Radio Equipment Directive 2014/53/EU compliance, use only SonicOS software and accessories provided with this appliance and by SonicWall. Diese SonicWall Appliance enthlt Funkanlagen zur Bereitstellung von RLAN/WLAN im Frequenzbereich von 2,4 GHz und 5 GHz. Verwenden Sie zur Einhaltung der Funkanlagenrichtlinie 2014/53/EU (Radio Equipment Directive RED) ausschlielich SonicOS Software und Zubehr, das mit dieser Appliance und von SonicWall bereitgestellt wird. To maintain safe exposure levels to electromagnetic fields, place appliance a minimum of (30) cm from all persons and domestic animals. Zur Einhaltung unbedenklicher Expositionswerte durch elektromagnetische Felder sollte sich die Appliance mindestens (TBD) cm von Personen und Haustieren entfernt befinden. This SonicWall wireless appliance is restricted to indoor use. Diese SonicWall Appliance ist auf die Nutzung in Innenrumen beschrnkt. Frequency Band Maximum RadioFrequency Power Transmitted MHz dBm EIRP 2412 2472 18.92 dBm 5180 5240 21.84 dBm 5260 5320 21.78 dBm 5500 5700 28.65 dBm FCC ID: 2AKCZ0D0 This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. NOTICE: The FCC regulations provide that changes or modifications not expressly approved by SonicWall Inc. could void your authority to operate this equipment. SonicWall SonicWave 224 w Beta Quick Start Guide 8 These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna. Relocate the system with respect to the receiver. Move the system away from the receiver. Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of SonicWall Inc. or an experienced radio/television technician for additional suggestions. NOTE: This SonicWall Wireless WLAN device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by SonicWall could void your authority to operate the equipment. The following information is provided on the device or devices covered in this document in compliance with FCC regulations:
Product name:
SonicWall SonicWave 231c Regulatory Model: APL450D0 Company name:
SonicWall Inc. is the responsible party for this product. For an EMC compliance issue or a regulatory inquiry, please use the following contact information:
SonicWall Inc. 1033 McCarthy Boulevard Milpitas, California 95035 USA 4087459600 Radiation exposure statement (FCC) CAUTION: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, this device should be used in such a manner that the potential for human contact during normal operation is SonicWall SonicWave 224 w Beta Quick Start Guide 9 minimized. This device has been evaluated for and shown compliant with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 30 cm from a persons body). Details of the authorized configurations can be found at https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on the device. United States of America authorized channels SonicWall declares that the APL450D0 (FCC ID: 2AKCZ0D0) when sold in the USA is limited to CH1CH11 by specified firmware controlled in the USA. CAUTION: This device is restricted to indoor use due to its operation in the 5.15GHz to 5.25GHz frequency range. The FCC requires this product to be used indoors for the frequency range 5.15GHz to 5.25GHz to reduce the potential for harmful interference to cochannel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25GHz to 5.35GHz and 5.65GHz to 5.85GHz bands. These radar stations can cause interference with this device or can cause damage to this device, or both. The APL450D0 device has been designed to operate with an internal antenna. Antenna is not user accessible. Dynamic Frequency Selection (DFS) is required on all Wireless LAN Master devices
(usually Access Points) and Wireless LAN Clients (usually Wireless NICs) that operate within 5470MHz 5725MHz. SonicWaves that have these frequencies and channels enabled in this range comply with North American and International DFS requirements. Some frequencies are blocked, and cannot be selected by the user per each specific regional approval. Specific to the USA, at the urging of the Federal Communication Commission (FCC) user/installers should avoid operation frequencies near Terminal Doppler Weather Radar (TDWR) systems frequencies 56005650 MHz when installing a SonicWave within 35km of lineofsite of TDWR sites. If TDWR is within 35km the SonicWave, frequencies should be set to at least 30MHz above or below any TDWR system frequency at that site. TDWR locations and specific frequencies used can be found at http://spectrumbridge.com/udrs/home.aspx. Detailed current and background information can be found at http://www.wispa.org/?page_id=2341. SonicWall SonicWave 224 w Beta Quick Start Guide 1 0 FCC, Class B This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. NOTICE: The FCC regulations provide that changes or modifications not expressly approved by SonicWall Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the antenna of the radio/television receiver. Increase the separation between this equipment and the radio/television receiver. Plug the system into a different outlet so that the system and the receiver are on different power mains branch circuits. Consult a representative of SonicWall Inc. or an experienced radio/television technician for additional suggestions. SonicWall SonicWave 224 w Beta Quick Start Guide 1 1 Copyright 2018 SonicWall Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. SonicWall is a trademark or registered trademark of SonicWall Inc. and/or its affiliates in the U.S.A. and/or other countries. All other trademarks and registered trademarks are property of their respective owners. The information in this document is provided in connection with SonicWall Inc. and/or its affiliates' products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of SonicWall products. EXCEPT AS SET FORTH IN THE TERMS AND CONDITIONS AS SPECIFIED IN THE LICENSE AGREEMENT FOR THIS PRODUCT, SONICWALL AND/OR ITS AFFILIATES ASSUME NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. IN NO EVENT SHALL SONICWALL AND/OR ITS AFFILIATES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF SONICWALL AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SonicWall and/or its affiliates make no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserve the right to make changes to specifications and product descriptions at any time without notice. SonicWall Inc. and/or its affiliates do not make any commitment to update the information contained in this document. For more information, visit https://www.sonicwall.com/legal. To view the SonicWall End User Product Agreement, go to: https://www.sonicwall.com/legal/eupa. Select the language based on your geographic location to see the EUPA that applies to your region. Legend WARNING: A WARNING icon indicates a potential for property damage, personal injury, or death. CAUTION: A CAUTION icon indicates potential damage to hardware or loss of data if instructions are not followed. IMPORTANT NOTE, NOTE, TIP, MOBILE, or VIDEO: An information icon indicates supporting information. SonicWall SonicWave 224 w Beta Quick Start Guide 1 2 Last updated: 3/2/18 Beta Rev 00 SonicWall SonicWave 224 w Beta Quick Start Guide 1 3