PRODUCT SPECIFICATION 802.11b/g/n 2T2R Wireless LAN USB Module WN4645R MT7603U User Manual Page 1/12 CONTENT PRODUCT FEATURES .................................................................................................................... 7 PRODUCT SPECIFICATIONS ........................................................................................................ 8 MAIN CHIPSET ....................................................................................................................................... 8 FUNCTIONAL SPECIFICATIONS................................................................................................................ 8 RECOMMENDED OPERATION CONDITIONS ........................................................................ 10 DC CHARACTERISTICS ............................................................................................................... 10 RESET TIMING SPEC .................................................................................................................... 10 PIN ASSIGMENT ............................................................................................................................. 11 USB CONNECTOR SPEC ............................................................................................................... 11 EEPROM INFORMATION ............................................................................................................ 12 ENVIRONMENTAL ........................................................................................................................ 12 OPERATING .......................................................................................................................................... 12 STORAGE .............................................................................................................................................. 12 Page 2/12 FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be colocated with any other transmitters except in accordance with FCC multitransmitter product procedures. Refering to the multitransmitter policy, multipletransmitter(s) and module(s) can be operated simultaneously without C2PC. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Page 3/12 IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20 cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radiofrequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: AK8WN4645R ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Page 4/12 OEM Integrator Checklist The party below will implement the LITE-ON Module in host systems in accordance with the instructions specified in this document and the documents referenced herein. 1. The OEM integrator will ensure the Module is integrated in a host systems using only the approved antenna model(s) described in this document. 2. The OEM integrator will ensure the antenna placement inside the host system will maintain the required spacing to end user for RF Exposure compliance, as specified in this document. 3. If other radios are integrated inside the host with the LITE-ON Module, the OEM integrator will contact its test lab, TCB or LITE-ON to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. 4. The OEM integrator will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. 5. The OEM integrator will ensure the Module is programmed in the factory with compliant transmit power not exceeding the levels specified in this document. LITE-ON requests that the OEM integrator acknowledge its receipt of this document and the above instructions. You may contact LITE-ON with any questions concerning this document or the responsibilities of the OEM integrator. IC Statement:
This device complies with Industry Canada license exempt RSS standard(s). Operation i s subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats Uni peuvent tre exploits. Slection d'autres canaux n'est pas possible. s / Canada du march, seul le canal 1 11 Page 5/12 ures. This device and its antenna(s) must not be co located with any other transmitters except in accordance with IC multi transmitter product proced Refering to the multi transmitter policy, multiple transmitter(s) and module(s) can be operated simultaneously without reassessment permissive change. Cet appareil et son antenne (s) ne doit pas tre co localiss ou fonctionnement en association avec une autre antenne ou transmetteur. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS 102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC:
409B-WN4645R ". Page 6/12 PRODUCT FEATURES Operate at ISM frequency Band (2.4GHz) IEEE Standards Support, 802.11b, 802.11g and 802.11n Support USB 2.0 host interface Enterprise level security supporting: WPA, WPA2, WPS2.0, WAPI Two-stream IEEE 802.11n support for 20MHz and 40MHz bandwidth channels provides PHY layer rates up to 300Mbps Integrated LNA, PA and T/R switch Support Wi-Fi Direct RoHS compliance Low Halogen compliance Page 7/12 PRODUCT SPECIFICATIONS MAIN CHIPSET MAC/ Baseband/ RF: MediaTek MT7603U FUNCTIONAL SPECIFICATIONS Wi-Fi Function Standard IEEE802.11b; IEEE 802.11g; IEEE 802.11n Bus Interface Data Rate Media Access Control Modulation Techniques Network Architecture Operation Channel Frequency Range Receiver Sensitivity USB2.0 802.11b:
802.11g:
802.11n:
11, 5.5, 2, 1 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz CSMA/CA with ACK 802.11b:
CCK, DQPSK, DBPSK 802.11g:
802.11n:
64QAM, 16QAM, QPSK, BPSK 64QAM, 16QAM, QPSK, BPSK Ad-hoc mode (Peer-to-Peer) Infrastructure mode 2.4GHz 11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 14: (Ch. 1-14) Japan 802.11bg 802.11b:
2.400 ~ 2.4835 GHz 802.11g:
-88 dBm@1Mbps
-82 dBm@11Mbps
-86 dBm@6Mbps
-71 dBm@54Mbps 802.11n:
20MHz
-86 dBm@MCS0 Page 8/12 Security Operating Voltage OS Supported Power Consumption Antenna Type
-68 dBm@MCS7 40MHz
-83 dBm@MCS0
-65 dBm@MCS7 WPA, WPA2, WPS, WEP 64b&128bit, IEEE 802.1X, IEEE 802.11i 5V 10% I/O supply voltage Linux based Mode Peak 2.4G 700mA Average 2.4G 332mA 210mA 100mA 48mA TX RX Unassociated Idle Standby@ wake mode Metal antenna Page 9/12 Min n 4.5 Min n 2.97 7 1.14 4 1.34 4 Min n
-0.2 8 2.0
-0.2 8 2.4 Ty yp 5 Max x 5.5 5 Units V Typ yp 3.3 3 1.2 2 1.6 6 Ty yp
-
-
-
-
Max x 3.63 3 1.26 6 1.76 6 Units V V V Max x 0.6 6 3.63 3 0.4 4 3.63 3 Units V V V DED OPER RATION CO ONDITION NS RE COMMEND Module For Sy ymbol V VCC Rating 5 5V Supply V oltage IC For MT7603U I ymbol Sy DD33 VD VD DD12 DD16 VD 3 1 1 Rating
.3V Supply
.2V Supply
.6V Supply Voltage Voltage Voltage DC C CHARAC ymbol Sy VIL VIH V VOL V VOH CTERISTIC CS In nput Low Vo In nput High V O Output Low V O Output High V Parameter r oltage oltage Voltage Voltage RE SET TIMIN NG SPEC Page 10/12 PIN N ASSIGME ENT Pin n. 1 2 3 4 5 6 7 8 Define CC CC _D-
_D+
Pin D
+5VC
+5VC USB_ USB_ GND RESE WoW GND ET#
WLAN#
ription Descr urce 5V sou urce 5V sou Data-
USB D USB D Data+
nd Groun System m reset MT7 up system v Wake Groun nd 7603U, low a via wifi, low active active Status YES YES YES YES YES YES YES YES US Man Thic B CONNE nufacture P ckness of go ECTOR SPE P/N: S1315-
old flash pla EC 08RVB-SB3 ated: 1u 3-KH Page 11/12 EEPROM INFORMATION Reg Domain World Wide 2.4G Read from registry; Control by driver Offset 0x39 for 2.4G: 0xFF Vendor ID Product ID 0x0E8D 0x7603 ENVIRONMENTAL Operating Operating Temperature: 0 to 70 C (32 to 158 F) Relative Humidity: 5-90% (non-condensing) Storage Temperature: -20 to 70 C (-4 to 158 F) Relative Humidity: 5-95% (non-condensing Page 12/12