| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 1.15 MiB | / November 11 2005 | |||
| 1 | Cover Letter(s) | / November 11 2005 | ||||||
| 1 | Cover Letter(s) | / November 11 2005 | ||||||
| 1 | Cover Letter(s) | / November 11 2005 | ||||||
| 1 | External Photos | / November 11 2005 | ||||||
| 1 | ID Label/Location Info | / November 11 2005 | ||||||
| 1 | Internal Photos | / November 11 2005 | ||||||
| 1 | Cover Letter(s) | / November 11 2005 | ||||||
| 1 | Test Setup Photos | / November 11 2005 | ||||||
| 1 | Cover Letter(s) | / November 11 2005 | ||||||
| 1 | Test Report | / November 11 2005 |
| 1 | User Manual | Users Manual | 1.15 MiB | / November 11 2005 |
2-347-712-13(1) Wireless Microphone Package Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. UWP-C1/C2/C3 UWP-S1/S2 UWP-X1/X2 2003 Sony Corporation COPY For the AC adapter supplied with UWP-S1/S2 Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-
over. 2 Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. IMPORTANT The name plate is located on the bottom (AC-911). WARNING This unit has no power switch. When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power cord to socket-outlet which must be provided near the unit and easily accessible. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power cord. COPY lappareil qu un technicien qualifi. IMPORTANT La plaquette signaltique est pose sur le dessous de lappareil (AC-911). AVERTISSEMENT Cet appareil ne possde pas dinterrupteur dalimentation. Lors de linstallation de lappareil, incorporer un dispositif de coupure facilement accessible dans le cblage fixe ou brancher le cordon dalimentation dans une prise murale proche de lappareil et facilement accessible. En cas de problme lors du fonctionnement de lappareil, enclencher le dispositif de coupure dalimentation ou dbrancher le cordon de la prise. ATTENTION Pour viter tout choc lectrique, ajuster la lame large de la fiche sur la fente large et linsrer fond. WARNUNG Um die Gefahr von Brnden oder elektrischen Schlgen zu verringern, darf dieses Gert nicht Regen oder Feuchtigkeit ausgesetzt werden. Um einen elektrischen Schlag zu vermeiden, darf das Gehuse nicht geffnet werden. berlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. 3 This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION To prevent electric shock, match wide blade of plug to wide slot, fully insert. AVERTISSEMENT Afin de rduire les risques dincendie ou dlectrocution, ne pas exposer cet appareil la pluie ou lhumidit. Afin dcarter tout risque dlectrocution, garder le coffret ferm. Ne confier lentretien COPY AVVERTENZA Il presente apparecchio non dotato di interruttore di alimentazione. Quando si installa lapparecchio, includere nellimpianto fisso un dispositivo di disconnessione rapidamente accessibile o collegare il cavo di alimentazione ad una presa in prossimit dellapparecchio e che sia facilmente raggiungibile. Nel caso in cui si dovesse verificare una anomalia durante il funzionamento dellapparecchio, agire sullinterruttore del dispositivo di disconnessione o disconnettere il cavo di alimentazione. ATTENZIONE Per evitare scosse elettriche assicurarsi che la spina sia inserita correttamente e completamente nella presa. ADVERTENCIA Para reducir el riesgo de electrocucin, no exponga este aparato a la lluvia ni a la humedad. Para evitar descargas elctricas, no abra el aparato. Solicite asistencia tcnica nicamente a personal especializado. IMPORTANTE La placa de caracteristicas se encuentra en la parte inferior (AC-
911). WICHTIG Am Boden des Gerts befindet sich das Typenschild (AC-911). WARNUNG Dieses Gert hat keinen Netzschalter. Beim Einbau des Gerts ist daher im Festkabel ein leicht zugnglicher Unterbrecher einzufgen, oder das Netzkabel muss mit einer in der Nhe des Gerts befindlichen, leicht zugnglichen Wandsteckdose verbunden werden. Wenn whrend des Betriebs eine Funktionsstrung auftritt, ist der Unterbrecher zu bettigen bzw. das Netzkabel abzuziehen, damit die Stromversorgung zum Gert unterbrochen wird. ACHTUNG Um die Gefahr elektrischer Schlge zu verhindern, immer den Stecker richtig und vollstndig einstecken. ATTENZIONE Per ridurre il rischio di incendi o scosse elettriche, non esporre questo apparato alla pioggia o allumidit. Per evitare scosse elettriche, non aprire lapparecchio. Per le riparazioni, rivolgersi solo a personale qualificato. IMPORTANTE La targhetta con il nome si trova sul fondo (AC-911). 4 COPY ADVERTENCIA Esta unidad no tiene interruptor elctrico. Cuando instale la unidad, incluya un dispositivo de desconexin de fcil acceso en el cableado fijo o enchufe el cable elctrico a un tomacorriente cerca de la unidad y de fcil acceso. Si se produce una falla durante el funcionamiento de la unidad, utilice el dispositivo de desconexin para desconectar la electricidad o desenchufe el cable elctrico. PRECAUCIN Para evitar descarga elctrica, alinee la pata ancha del enchufe en la ranura ancha y enchufe a fondo. 5 COPY For UTX-B1, UTX-H1, and UTX-P1 Transmitters Notice for customers in the U.S.A. Use of Sony wireless devices is regulated by the Federal Communications Commission as described in Part 74 subpart H of the FCC regulations and users authorized thereby are required to obtain an appropriate license. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate this device. This device complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR). Owners Record The model and serial numbers are located at the rear or on the bottom of the unit. Record the model and serial numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. _____________________ Serial No. _____________________ IMPORTANT The name plate is located on the bottom and the serial number is located inside the battery compartment
(UTX-P1). IMPORTANT La plaquette signaltique est pose sur le dessous de lappareil et le numro de srie dans le logement des piles
(UTX-P1). WICHTIG Am Boden des Gerts befindet sich das Typenschild und die Seriennummer befindet sich innen im Batteriefach (UTX-P1). IMPORTANTE La targhetta con il nome si trova sul fondo e il numero di serie si trova allinterno del vano pile (UTX-P1). IMPORTANTE La placa de caracteristicas se encuentra en la parte inferior y el nmero de serie est en el interior del compartimiento de pilas (UTX-P1). 6 COPY Notice for customers in Canada:
Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123. A licence is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the licence is issued on no-interference, no-
protection basis with respect to broadcast signals. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the radio certification number only signifies that Industry Canada technical specifications were met. Remarque lintention des utilisateurs au Canada:
Lusage des appareils sans fil Sony est rglement par lIndustrie Canada comme dcrit dans leur Cahier des Normes Radiolectriques CNR-123. Une licence est normalement requise. Le bureau de lIndustrie Canada doit tre contact. Lorsque le fonctionnement de lappareil respecte les limites de la bande de radiodiffusion, la licence est accorde sur la base dune non-interfrence, non-protection pour les signaux de radiodiffusion. Lutilisation de cet appareil est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer dinterfrences, et (2) cet appareil doit accepter toutes les interfrences, y compris les interfrences capables de provoquer un fonctionnement non souhait de lappareil. Lexpression <<IC:>> avant le numro dhomologation/
enregistrement signifie seulement que les spcifications techniques de lIndustrie Canada ont t respectes. Fr Kunden in Deutshland (UTX-
B1/H1/P1) Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gert abschaltet und signalisiert Batterie leer oder nach lngerer Gebrauchsdauer der Batterien nicht mehr einwandfrei funktioniert. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Voor de Klanten in Nederland
(UTX-B1/H1/P1) Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). 7 COPY Notice for customers in Europe Notification aux clients europens Hinweis fr die Kunden in Europa Avvertenza per gli utilizzatori in Europa Aviso para los clientes de Europa Nota para utilizadores da Europa Mededeling voor de klanten in Europa Att observera fr kunder i Europa Meddelelse til kunderne i Europa Huomautus Euroopassa asuville asiakkaillemme 854.125 - 862 MHz U.K. 790 - 814 MHz Germany 800 - 820 MHz Norway Luxembourg 800 - 830 MHz, Belgium Denmark France Italy Sweden Switzerland Finland Iceland 854.125 - 862 MHz 854.125 - 862 MHz 800.100 - 819.900 MHz 798 - 830 MHz 800 - 820 MHz 800 - 820 MHz 800 - 820 MHz 800.100 - 819.900 MHz 800 - 814 MHz 8 Hereby, Sony Corporation declares that this UTX-B1/UTX-H1/UTX-P1 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL:
http://www.compliance.sony.de/
Note:
In some countries additional frequency bands may be used with the agreement of the national authority. Sony Corporation dclare par ces prsentes que le UTX-B1/UTX-H1/
UTX-P1 est conforme aux exigences essentielles et aux dispositions applicables de la Directive 1999/5/CE. Pour les dtails, accdez lURL suivante:
http://www.compliance.sony.de/
Remarque:
Dans certains pays, des bandes de frquences additionnelles pourront tre utilises avec laccord des autorits nationales. Hiermit erklrt Sony Corporation, dass die vorliegende Einheit UTX-B1/
UTX-H1/UTX-P1 den wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EC entspricht. Fr Einzelheiten siehe folgende URL:
http://www.compliance.sony.de/
Hinweis:
In manchen Lndern ist mit Genehmigung der zustndigen Behrden u.U. die Nutzung weiterer Frequenzbnder mglich. COPY Con questo Sony Corporation dichiara che questo UTX-B1/UTX-H1/UTX-
P1 in conformit con i requisiti essenziali e altri provvedimenti in materia della Direttiva 1999/5/CE. Per dettagli, si prega di accedere alla seguente URL:
http://www.compliance.sony.de/
Nota:
In alcuni paesi possono essere usate bande di frequenza supplementari con il permesso delle autorit nazionali. Sony Corporation declara aqu que este modelo, UTX-B1/UTX-H1/UTX-
P1, cumple los requisitos esenciales y dems provisiones pertinentes de la Directiva 1999/5/EC.Con respecto a los detalles, realice el acceso a la URL:
http://www.compliance.sony.de/
Nota:
En algunos pases pueden utilizarse bandas de frecuencia adicionales de acuerdo con la autoridad nacional. A Sony Corporation declara que o modelo UTX-B1/UTX-H1/UTX-P1 est em conformidade com as exigncias essenciais e outras provises pertinentes da Directiva 1999/5/EC. Mais informaes neste endereo da Internet:
http://www.compliance.sony.de/
Sony Corporation verklaart hierbij dat de UTX-B1/UTX-H1/UTX-P1 voldoet aan de primaire vereisten en andere relevante voorschriften van de Europese Bepaling 1999/5/EC. Nadere bijzonderheden vindt u op de volgende website:
http://www.compliance.sony.de/
Opmerking:
In bepaalde landen kan er gebruik gemaakt worden van aanvullende frequentiebanden, mits toegestaan door de nationale instanties. Sony Corporation frkunnar hrmed att denna UTX-B1/UTX-H1/UTX-P1 uppfyller de huvudsakliga kraven och andra relevanta villkor i direktivet 1999/5/EC. Se fljande URL fr nrmare detaljer:
http://www.compliance.sony.de/
Observera:
I vissa lnder kan det hnda att ytterligare frekvensband anvnds efter verenskommelse med det landets myndigheter. Sony Corporation erklrer herved, at denne UTX-B1/UTX-H1/UTX-P1 er i overensstemmelse med de essentielle krav og andre relevante bestemmelser i direktiv 1999/5/EC. bn venligst den flgende URL angende detaljer:
http://www.compliance.sony.de/
Obs.:
Em alguns pases uma faixa adicional de frequncias pode ser utilizada com autorizao do governo nacional. Bemrk:
I nogle land kan yderligere frekvensbnd blive anvendt med de nationale autoriteters samtykke. 9 COPY Sony Corporation julistaa tten, ett tm UTX-B1/UTX-H1/UTX-P1 vastaa direktiivin 1999/5/EC olennaisia vaatimuksia ja muita asiaankuuluvia mryksi. Katso tarkemmat tiedot osoitteesta:
http://www.compliance.sony.de/
Huom!
Joissakin maissa listaajuuskaistoja voidaan kytt viranomaisten suostumuksella. Note for customers in Switzerland:
Before use, a request of concession for a wireless microphone (Frequency Class 3) has to be submitted to Bakom. Note concernant les utilisateurs en Suisse:
Une demande de concession de microphone sans fil (frquence classe 3) doit tre prsente au Bakom avant dutiliser lappareil. 10 Hinweis fr Kunden in der Schweiz:
Vor Inbetriebnahme ist eine Konzessionsanforderung fr ein drahtloses Mikrofon (Frequenzklasse 3) bei Bakom einzureichen. Note for customers in Finland:
To own and use, it is necessary to obtain an individual licence of the Telecommunications Administration Center. Huomautus Suomessa asuville asiakkaillemme Omitusta ja kytt varten on tarpeen hankkia henkilkohtainen lupa tietoliikennehallintokeskuksesta. Note for customers in Luxembourg:
Before any use of an equipment, the frequencies required have to be, if necessary according to the regulations in force, assigned prior to usage by the ILT. Remarque pour les clients au Luxembourg:
Avant tout emploi de cet appareil, si ncessaire conformment la rglementation en vigueur, les frquences requises doivent tre assignes, avant lusage par le ILT. Hinweis fr Kunden in Luxemburg:
Vor Inbetriebnahme eines Gerts mssen die Frequenzen gegebenenfalls nach den geltenden Vorschriften vor dem Gebrauch von der ILT zugewiesen werden. COPY Note for customers in Italy:
The use of this product within Italy is subject to article 334 of the Postal and Telecommunications regulations. Nota per i clienti in Italia:
Luso del prodotto sul territorio italiano soggetto alle regolamentazioni del Codice Postale e delle Telecomunicazioni art. 334. Note for customers in Belgium:
Using the UTX-B1/UTX-H1 with 30 mW RF output power is not allowed. Be sure to set the RF output power to 5 mW. The UTX-P1s RF output power is 50 mW. Using the UTX-P1 in Belgium is not allowed. Remarque concernant les utilisateurs en Belgique:
Lemploi du UTX-B1/UTX-H1 avec une puissance de sortie RF 30 mW nest pas autoris. Bien rgler la puissance de sortie RF 5 mW. La puissance de sortie RF du UTX-P1 est 50 mW. Lemploi du UTX-P1 nest pas autoris en Belgique. Hinweis fr Kunden in Belgien:
Verwendung des UTX-B1/UTX-H1 mit 30 mW HF-Ausgangsleistung ist nicht zulssig. Immer die HF-
Ausgangsleistung auf 5 mW einstellen. Die Ausgangsleistung des UTX-P1 betrgt 50 mW. Verwendung des UTX-P1 in Belgien ist nicht zulssig. Mededeling voor de klanten in Belgi:
Het is niet toegestaan de UTX-B1/
UTX-H1 te gebruiken met een RF uitgangsvermogen van 30 mW. Zorg dat het RF uitgangsvermogen is ingesteld op 5 mW. Het RF uitgangsvermogen van de UTX-P1 is 50 mW. De UTX-P1 mag niet in Belgi worden gebruikt. Note for customers in Norway:
Using this transmitter requires the Individual License. Hinweis fr Kunden in Deutschland:
Vor Inbetriebnahme muss bei der zustndigen Auenstelle der Regulierungsbehrde (Reg TP) eine Kanalzuweisung beantragt werden. Note for customers in Iceland:
Using this transmitter requires the Individual License. Note for customers in Sweden:
Using this transmitter requires the Individual License. Att observera fr kunder i Sverige:
Fr att anvnda denna sndare krvs Individuell Licens. 11 COPY For URX-P1, URX-M1, and URX-R1 Tuners Owners Record The model and serial numbers are located at the rear or on the side of the unit. Record the model and serial numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. _____________________ Serial No. _____________________ Notice for customers in the U.S.A. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Declaration of Conformity Trade Name:
Model No.:
SONY URX-P1 URX-M1 URX-R1 Responsible Party:
Address:
Sony Electronics Inc. 16450 W. Bernardo Dr, San Diego, CA. 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. 12 If you have any questions about this product, you may call:
Sony Customer Information Service Center 1-800-222-7669 or http://
www.sony.com/
Notice for customers in Canada:
Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123. A licence is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the licence is issued on no-interference, no-
protection basis with respect to broadcast signals. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the radio certification number only signifies that Industry Canada technical specifications were met. Remarque lintention des utilisateurs au Canada:
Lusage des appareils sans fil Sony est rglement par lIndustrie Canada comme dcrit dans leur Cahier des Normes Radiolectriques CNR-123. Une licence est normalement requise. Le bureau de lIndustrie Canada doit tre contact. Lorsque le fonctionnement de lappareil respecte COPY les limites de la bande de radiodiffusion, la licence est accorde sur la base dune non-interfrence, non-protection pour les signaux de radiodiffusion. Lutilisation de cet appareil est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer dinterfrences, et (2) cet appareil doit accepter toutes les interfrences, y compris les interfrences capables de provoquer un fonctionnement non souhait de lappareil. Lexpression <<IC:>> avant le numro dhomologation/
enregistrement signifie seulement que les spcifications techniques de lIndustrie Canada ont t respectes. Fr Kunden in Deutshland (URX-
P1) Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gert abschaltet und signalisiert Batterie leer oder nach lngerer Gebrauchsdauer der Batterien nicht mehr einwandfrei funktioniert. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Voor de Klanten in Nederland
(URX-P1) Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA). Notice for customers in Europe Notification aux clients europens Hinweis fr die Kunden in Europa Avvertenza per gli utilizzatori in Europa Aviso para los clientes de Europa Nota para utilizadores da Europa Mededeling voor de klanten in Europa Att observera fr kunder i Europa Meddelelse til kunderne i Europa Huomautus Euroopassa asuville asiakkaillemme 854.125 - 862 MHz U.K. 790 - 814 MHz Germany 800 - 820 MHz Norway Luxembourg 800 - 830 MHz, Belgium Denmark France Italy Sweden Switzerland Finland Iceland 854.125 - 862 MHz 854.125 - 862 MHz 800.100 - 819.900 MHz 798 - 830 MHz 800 - 820 MHz 800 - 820 MHz 800 - 820 MHz 800.100 - 819.900 MHz 800 - 814 MHz Hereby, Sony Corporation declares that this URX-P1/M1/R1 is in compliance with the essential 13 COPY endereo da Internet:
http://www.compliance.sony.de/
Sony Corportion verklaart hierbij dat de URX-P1/M1/R1 voldoet aan de primaire vereisten en andere relevante voorschriften van de Europese Bepaling 1999/5/EC. Nadere bijzonderheden vindt u op de volgende website:
http://www.compliance.sony.de/
Sony Corporation frkunnar hrmed att denna URX-P1/M1/R1 uppfyller de huvudsakliga kraven och andra relevanta villkor i direktivet 1999/5/
EC. Se fljande URL fr nrmare detaljer:
http://www.compliance.sony.de/
Sony Corporation erklrer herved, at denne URX-P1/M1/R1 er i overensstemmelse med de essentielle krav og andre relevante bestemmelser i direktiv 1999/5/EC. bn venligst den flgende URL angende detaljer:
http://www.compliance.sony.de/
Sony Corporation julistaa tten, ett tm URX-P1/M1/R1 vastaa direktiivin 1999/5/EC olennaisia vaatimuksia ja muita asiaankuuluvia mryksi. Katso tarkemmat tiedot osoitteesta:
http://www.compliance.sony.de/
requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL:
http://www.compliance.sony.de/
Sony Corporation dclare par ces prsentes que le URX-P1/M1/R1 est conforme aux exigences essentielles et aux dispositions applicables de la Directive 1999/5/CE. Pour les dtails, accdez lURL suivante:
http://www.compliance.sony.de/
Hiermit erklrt Sony Corporation, dass die vorliegende Einheit URX-P1/
M1/R1 den wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EC entspricht. Fr Einzelheiten siehe folgende URL:
http://www.compliance.sony.de/
Con questo Sony Corporation dichiara che questo URX-P1/M1/R1 in conformit con i requisiti essenziali e altri provvedimenti in materia della Direttiva 1999/5/CE. Per dettagli, si prega di accedere alla seguente URL:
http://www.compliance.sony.de/
Sony Corporation declara aqu que este modelo, URX-P1/M1/R1 cumple los requisitos esenciales y dems provisiones pertinentes de la Directiva 1999/5/EC. Con respecto a los detalles, realice el acceso a la URL:
http://www.compliance.sony.de/
A Sony Corporation declara pela presente que o modelo URX-P1/M1/
R1 est em conformidade com as exigncias essenciais e outras provises pertinentes da Directiva 1999/5/EC. Mais informaes neste 14 COPY Para os clientes no Brasil O uso dos modulos UWP-C1, S1, X1 e UWP-C2, S2, X2 atende s normas e resolues da Anatel, conforme homologao a seguir:
15 COPY Table of Contents Table of Contents Configuration of the Packages ........................... 17 UWP-C1 ................................... 17 UWP-C2 ................................... 18 UWP-C3 ................................... 19 UWP-S1 ................................... 20 UWP-S2 ................................... 21 UWP-X1 .................................. 22 UWP-X2 .................................. 23 Features .................................. 24 Using the CD-ROM Manual.... 26 CD-ROM system requirements ............................. 26 Preparations ............................. 26 To read the operating instructions ............................... 26 To read the Sony Wireless Microphone System Frequency List ........................................... 26 Precautions............................. 28 Parts Identification ................. 29 Body-pack transmitter
(UTX-B1)................................. 29 Hand-held microphone
(UTX-H1) ................................ 30 Plug-on transmitter
(UTX-P1) ................................. 31 Portable diversity tuner
(URX-P1) ................................. 33 Half-rack size diversity tuner
(URX-R1) ................................ 35 Diversity tuner module
(URX-M1) ............................... 36 Power Supply ......................... 38 Inserting the batteries ............... 38 Attachment and Installation Procedures ........................ 41 Attaching the supplied accessories to the body-pack transmitter (UTX-B1) .............. 41 16 Attaching the supplied accessory to the hand-held microphone
(UTX-H1) ................................ 42 Inserting the plug-on transmitter
(UTX-P1) into the supplied soft case........................................... 42 Attaching optional accessory to the plug-on transmitter
(UTX-P1) ................................. 43 Attaching the supplied accessories to the portable diversity tuner (URX-P1)......... 43 Installing the diversity tuner module (URX-M1) .................. 44 Settings ................................... 47 Setting the transmission channel ..................................... 47 Setting the reception channel ... 48 Detecting and selecting the available channels automatically
(diversity tuner module
(URX-M1) only) ...................... 50 Setting the attenuation level of the audio input ..................... 50 Resetting the accumulated battery use time indication ....... 51 Setting the RF output level ...... 52 Setting the monitor level
(portable diversity tuner
(URX-P1) only) ....................... 52 Operation ................................ 53 System Configurations .......... 54 Configuration examples of the UWP-C1/C2/S1/S2/X1/X2 ...... 54 Configuration example of the UWP-C3................................... 57 Error Messages ...................... 58 Troubleshooting ..................... 59 Specifications ......................... 61 COPY Configuration of the Packages This operation manual is for the UWP-C1/C2/C3/S1/S2/X1/X2 wireless microphone packages. The contents of each package are described below. UWP-C1 The UWP-C1 consists of a body-pack transmitter (UTX-B1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C1 makes a mobile system for ENG (Electronic News Gathering) or EFP
(Electronic Field Production) purposes. Body-pack transmitter
(UTX-B1) (1) Portable diversity tuner
(URX-P1) (1) Supplied accessories Omni-directional lavalier microphone
(1) Wind screen (1) Holder clip (1) XLR-BMP conversion cable (1) Shoe mount adapter (1) Belt clip (2) Stereo mini plug-BMP conversion cable (1) Microphone stand adapter (1) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1) (for AU66 and CE67 models) Warranty card (1) (for U62 and U66 models) 17 COPY Configuration of the Packages UWP-C2 The UWP-C2 consists of a hand-held microphone (UTX-H1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C2 makes a mobile system for ENG (Electronic News Gathering) or EFP
(Electronic Field Production) purposes. Hand-held microphone
(UTX-H1) (1) Portable diversity tuner
(URX-P1) (1) Supplied accessories Microphone holder (1) Belt clip (1) Shoe mount adapter (1) XLR-BMP conversion cable (1) Stereo mini plug-BMP conversion cable (1) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1)
(for AU66 and CE67 models) Warranty card (1) (for CE62 and U66 models) Microphone stand adapter (1) 18 COPY UWP-C3 The UWP-C3 consists of a plug-on transmitter (UTX-P1) and a portable diversity tuner (URX-P1). When used in conjunction with a compact camcorder, the UWP-C3 makes a mobile system for ENG (Electronic News Gathering) or EFP
(Electronic Field Production) purposes. Plug-on transmitter
(UTX-P1) (1) Portable diversity tuner
(URX-P1) (1) Supplied accessories Soft case (1) Belt clip (1) Shoe mount adapter (1) XLR-BMP conversion cable (1) Stereo mini plug-BMP conversion cable (1) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1) (for CE67 model) Warranty card (1) (for U62 and U66 models) 19 COPY Configuration of the Packages UWP-S1 The UWP-S1 consists of a body-pack transmitter (UTX-B1) and a half-rack size diversity tuner (URX-R1). The UWP-S1 is suitable for constructing a wireless system for AV presentations. Body-pack transmitter
(UTX-B1) (1) Half-rack size diversity tuner
(URX-R1) (1) Supplied accessories Unidirectional lavalier microphone (1) Wind screen (1) Holder clip (1) AC adapter (1) Belt clip (1) AC-S906T (for U62 and U66 models) AC-S906 (for CE62 model) AC-S911 (for CE67 model) AC-X1 (for AU66 model) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1)
(for AU66 and CE67 models) Warranty card (1) (for U62 and U66 models) 20 COPY UWP-S2 The UWP-S2 consists of a hand-held microphone (UTX-H1) and a half-rack size diversity tuner (URX-R1). The UWP-S2 is suitable for constructing a wireless system for AV presentations. Hand-held microphone
(UTX-H1) (1) Half-rack size diversity tuner
(URX-R1) (1) Supplied accessories Microphone holder (1) AC adapter (1) AC-S906T (for U62 and U66 models) AC-S906 (for CE62 model) AC-S911 (for CE67 model) AC-X1 (for AU66 model) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1) (for AU66 and CE67 models) Warranty card (1) (for U62 and U66 models) 21 COPY Configuration of the Packages UWP-X1 The UWP-X1 consists of a body-pack transmitter (UTX-B1) and a diversity tuner module (URX-M1). By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible. Body-pack transmitter
(UTX-B1) (1) Diversity tuner module
(URX-M1) (1) Supplied accessories Unidirectional lavalier microphone (1) Wind screen (1) Holder clip (1) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1)
(for AU66 and CE67 models) Warranty card (1) (for U62 and U66 models) Belt clip (1) 22 COPY UWP-X2 The UWP-X2 consists of a hand-held microphone (UTX-H1) and a diversity tuner module (URX-M1) . By installing the tuner module into a tuner base unit or a powered mixer, the system construction to meet the desired purpose of use and required system scale becomes possible. Hand-held microphone
(UTX-H1) (1) Diversity tuner module
(URX-M1) (1) Supplied accessories Microphone holder (1) Operation manual (1) CD-ROM (1) (for U62, U66, CE62, and CE67 models) Sony Wireless Microphone System Frequency List (1)
(for AU66 and CE67 models) Warranty card (1) (for U62 and U66 models) 23 COPY Features Features Each of the UWP-C1/C2/C3/S1/S2/
X1/X2 wireless microphone packages
(referred to as the UWP series hereafter) combines a transmitter
(body-pack transmitter (UTX-B1), hand-held microphone (UTX-H1), or plug-on transmitter (UTX-P1)) and a receiver (portable diversity tuner
(URX-P1), half-rack size diversity tuner (URX-R1), or diversity tuner module (URX-M1)). The UWP series can be used with a compact camcorder for ENG (Electronic News Gathering) purposes, and with a powered mixer for AV presentations or as a PA
(public address) system. Note The UWP series is not compatible with conventional WRT series transmitters, WRR series tuners, or WRU series tuner units. The features of each package are described below. UWP-C1 Body-pack transmitter (UTX-B1) This is a small and lightweight transmitter with a crystal-controlled PLL (phase lock loop) synthesized system and a BMP-type microphone input connector. The RF power output can be set at 30 mW or at 5 mW. 24 Portable diversity tuner
(URX-P1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with an adapter for mounting the tuner on the compact camcorder
(DSR-PD170/PD170P, HVR-Z1, etc.). UWP-C2 Hand-held microphone (UTX-H1) This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 30 mW or at 5 mW. Portable diversity tuner
(URX-P1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with an adapter for mounting the tuner on the compact camcorder
(DSR-PD170/PD170P, HVR-Z1, etc.). UWP-C3 Plug-on transmitter (UTX-P1) This is a small and lightweight plug-
on transmitter with a crystal-
controlled PLL (phase lock loop) synthesized system and an XLR-type microphone input connector. The RF power output is set at 50 mW. COPY Portable diversity tuner (URX-
P1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with an adapter for mounting the tuner on the compact camcorder
(DSR-PD170/PD170P, HVR-Z1, etc.). Half-rack size diversity tuner
(URX-R1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with two types of audio connectors (1/4-inch jack and XLR type) on the rear panel. UWP-S1 UWP-X1 Body-pack transmitter (UTX-B1) This is a small and lightweight transmitter with a crystal-controlled PLL (phase lock loop) synthesized system and a BMP-type microphone input connector. The RF power output can be set at 30 mW or at 5 mW. Body-pack transmitter (UTX-B1) This is a small and lightweight transmitter with a crystal-controlled PLL (phase lock loop) synthesized system and a BMP-type microphone input connector. The RF power output can be set at 30 mW or at 5 mW. Half-rack size diversity tuner
(URX-R1) This tuner employs a space diversity system with little signal dropout and two angle-adjustable antennas. It comes with two types of audio connectors (1/4-inch jack and XLR type) on the rear panel. UWP-S2 Hand-held microphone (UTX-H1) This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 30 mW or at 5 mW. Diversity tuner module
(URX-M1) This tuner module can be incorporated into the MB-806A Tuner Base Unit or SRP-X500P/X700P Powered Mixer. UWP-X2 Hand-held microphone (UTX-H1) This microphone is equipped with a built-in antenna and a unidirectional dynamic microphone unit. The RF power output can be set at 30 mW or at 5 mW. Diversity tuner module
(URX-M1) This tuner module can be incorporated into the MB-806A Tuner Base Unit or SRP-X500P/X700P Powered Mixer. 25 COPY Using the CD-ROM Manual Using the CD-ROM Manual The supplied CD-ROM includes operating instructions for the UWP series wireless microphone packages
(English, Japanese, French, German, Italian, and Spanish versions) and Sony Wireless Microphone System Frequency Lists (English, French, German, and Spanish versions). CD-ROM system requirements The following are required to access the supplied CD-ROM disc. Computer: PC with Intel Pentium CPU Installed memory: 64 MB or more CD-ROM drive: 8 or faster Monitor: Monitor supporting resolution of 800 600 or higher Operating system: Microsoft Windows XP Professional or Windows XP Home Edition When these requirements are not met, access to the CD-ROM disc may be slow, or not possible at all. Preparations One of the following programs must be installed on your computer in order to use the operating instructions contained on the CD-ROM disc. Adobe Acrobat Reader Version 4.0 or higher Adobe Reader Version 6.0 or higher 26 Note If Adobe Reader is not installed, you can download it from the following URL:
http://www.adobe.com/
To read the operating instructions To read the operating instructions contained in the CD-ROM disc, do the following. 1 Insert the CD-ROM disc in your CD-ROM drive. A cover page appears automatically in your browser. If it does not appear automatically in the browser, open My Computer, access the CD-ROM drive, and double-click the index.htm file. 2 Select and click the operating instructions that you want to read. A PDF file of the operating instructions opens. To read the Sony Wireless Microphone System Frequency List The frequency lists for U62 and U66 models (for the U.S.A.) and CE62 and CE67 models (for Europe) are contained in the CD-ROM disc. To read the frequency lists, do the following. COPY 1 Insert the CD-ROM disc in your CD-ROM drive. A cover page appears automatically in your browser. 2 Select and click the frequency list that you want to read. A PDF file of the frequency list opens. Note If you lose the CD-ROM disc or become unable to read its content, you can purchase a new CD-ROM disc to replace one that has been lost or damaged. Contact your Sony service representative. Trademarks Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/
or other countries. Adobe, Acrobat, and Adobe Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries. 27 COPY To prevent electromagnetic interference from portable communication devices The use of portable telephones and other communication devices near the UWP series product may result in malfunction and interference with audio signals. It is recommended that portable communication devices near the UWP series product be turned off. Precautions Precautions The UWP series product must be used within a temperature range of 0C to 40C (32F to 104F). Operating the UWP series product near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the UWP series product as far from such equipment as possible. The presence of the lighting equipment may produce electrical interference over the entire frequency range. Position the UWP series product so that interference is minimized. To avoid degradation of the signal-
to-noise ratio, do not use the UWP series product in noisy places or in locations subject to vibration, such as the following:
near electrical equipment, such as motors, transformers or dimmers near air conditioning equipment or places subject to direct air flow from an air conditioner near public address loudspeakers where adjacent equipment might knock against the tuner Keep the UWP series product as far from such equipment as possible or use buffering material. Clean the surface and the connectors of the UWP series product with a dry, soft cloth. Never use thinner, benzene, alcohol or any other chemicals, since these may mar the finish. 28 COPY Parts Identification Body-pack transmitter
(UTX-B1) 1 Antenna 2 Audio input connector Connect the supplied lavalier microphone here. 3 Power indicator Lights up red when the transmitter is tuned on. 4 Display section A B C D AF RF BATT H L CH E The E channel indication for U66 model is shown. A AF (audio frequency) indication Appears whenever the input audio signal is stronger than the reference level. B RF (radio frequency) indication Appears during signal transmission from the antenna. C RF (radio frequency) level indication Shows the RF output level setting. For details, see Setting the RF output level on page 52. D BATT (battery) indication Shows the battery condition. For details, see Power Supply on page 38. E CH (channel) indication Shows the transmission channel. Each time you press the SET button in transmission mode, the channel indication changes as follows. For details, see Settings on page 47. Transmission channel Transmission frequency Attenuation level of the input signal Accumulated battery use time Press the SET button. The channel/frequency indications for U66 model are shown. 29 COPY Parts Identification 5 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The button resets the accumulated battery use time to 00:00. 6 Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see Power Supply on page 38. 7 SET button Press to change and enter display parameters. For details, see Settings on page 47. 8 POWER switch Turns the power of the transmitter ON or OFF. Hand-held microphone
(UTX-H1) The rear side of the battery compartment 30 1 Power indicator Lights up red when the microphone is turned on. 2 POWER switch Turns the power of the microphone ON or OFF. 3 Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see Power Supply on page 38. 4 Display section A B C D H L E The E channel indication for U66 model is shown. A AF (audio frequency) indication Appears whenever the input audio signal is stronger than the reference level. B RF (radio frequency) indication Appears during signal transmission from the antenna. C RF (radio frequency) level indication Shows the RF output level setting. For details, see Setting the RF output level on page 52. COPY D BATT (battery) indication Shows the battery condition. For details, see Power Supply on page 38. E CH (channel) indication Shows the transmission channel. Each time you press the SET button, the channel indication changes as follows. For details, see Settings on page 47. Transmission channel Transmission frequency Attenuation level of the input signal Accumulated battery use time Press the SET button. Plug-on transmitter
(UTX-P1) Front side 6 The channel/frequency indications for U66 model are shown. Bottom side 5 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The button resets the accumulated battery use time to 00:00. 6 SET button Press to change display parameters. For details, see Settings on page 47. 1 Audio input connector (XLR type) Connect a microphone or a line output connector of an audio mixer, etc. 31 COPY 4 Display section A B AF RF BATT CH The D channel indication for U66 model is shown. A AF (audio frequency) indication Appears whenever the input audio signal is stronger than the reference level. B RF (radio frequency) indication Appears during signal transmission. C BATT (battery) indication Shows the battery condition. For details, see Power Supplyon page 38. D CH (channel) indication Shows the transmission channel. Each time you press the SET button in transmission mode, the channel indication changes as follows. For details, see Settings on page 47. Parts Identification 2 AF/PEAK (audio frequency/
peak) level indicator The color indicates the strength of the audio input signal. On in red: Audio input level is 40 dBV or more (when the INPUT selector is set to MIC) or +8 dBV or more (when the INPUT selector is set to LINE). On in green: Audio input level is 60 dBV or more and less than 40 dBV (when the INPUT selector is set to MIC) or 9 dBV or more and less than +8 dBV
(when the INPUT selector is set to LINE). Off: Audio input level is less than 60 dBV (when the INPUT selector is set to MIC) or less than 9 dBV (when the INPUT selector is set to LINE). 3 INPUT (input signal) selector Set this selector to MIC when a microphone is conneted to the audio input connector; set it to LINE when an audio mixer, etc. is conneted to the audio input connector. Notes The UTX-P1 does not support external power supply. Do not connect a mirophone which requires external power supply. Do not set the INPUT selector to MIC position while the audio signal is being input from the audio mixer, etc. Doing so may cause excessive audio input, resulting in distorted playback or recorded sound or damage to the playback or recording equipment. 32 COPY Portable diversity tuner
(URX-P1) Press the SET button. Transmission channel Transmission frequency Attenuation level of the input signal Accumulated battery use time The channel/frequency indications for U66 model are shown. 5 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the transmission channel, frequency, or attenuation level of the input signal. The - button resets the accumulated battery use time to 00:00. 6 SET button Press to change display parameters. For details, see Settings on page 47. 7 POWER switch Turns the power of the transmitter ON or OFF. 1 Antennas a/b The angle of the antennas can be adjusted manually. 2 MONITOR connector (3.5-mm diameter stereo mini jack) To monitor the tuner output, connect the headphones to this connector. 3 RF (radio frequency) indicator The color indicates the strength of the RF input signal. On in green: RF input is 15 dB*
8 Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see Power Supply on page 38. ..................................................................................................................................................................... Off: RF input is less than 15 dB*. or more.
* 0 dB = 1 VEMF 33 COPY Reception channel group and number Reception frequency Accumulated battery use time Press the SET button. 5 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the reception channel and frequency. The button resets the accumulated battery use time to 00:00. These buttons can also be used to adjust the monitor level. 6 Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see Power Supply on page 38. 7 SET button Press to change display parameters. For details, see Settings on page 47. 8 POWER switch Turns the power of the tuner ON or OFF. Parts Identification 4 Display section A B RF AF C BATT CH D A RF (radio frequency) indications The number of dots indicates the RF input level. B AF (audio frequency) indication Appears whenever the output audio signal is stronger than the reference level. C BATT (battery) indication Shows the battery condition. For details, see Power Supply on page 38. D GP (group)/CH (channel) indication Shows the reception channel group and channel number. Each time you press the SET button, the channel indication changes as follows. For details, see Settings on page 47. 34 COPY 9 OUTPUT (audio output) connector (3.5-mm diameter stereo mini jack) Connect one end of the supplied XLR-
BMP conversion cable or the stereo mini plug-BMP conversion cable here and the other end to the microphone input on a camcorder, mixer, or amplifier. If the microphone input connector on the device connected to the tuner is a stereo mini jack, connect the straight (BMP) plug to the tuner and the L-shaped (stereo mini) plug to the microphone input connector on the device. Half-rack size diversity tuner (URX-R1) Front panel Rear panel 1 POWER switch Turns the power of the tuner ON or OFF. 2 Antennas a/b The angle of the antennas can be adjusted manually. 3 MONITOR connector (phone jack) To monitor the tuner output, connect the headphones to this connector and adjust the monitor level with the MONITOR control. Use either stereo or monaural headphones. 4 MONITOR control Turn to adjust the output monitoring level (through the headphones). 5 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the reception channel and frequency. 6 Display section A B RF AF CH C A RF (radio frequency) indications The number of dots indicates the RF input level. 35 COPY Parts Identification B AF (audio frequency) indication Appears whenever the output audio signal is stronger than the reference level. C GP (group)/CH (channel) indication Shows the reception channel group and channel number. Each time you press the SET button, the channel indication changes as follows. For details, see Settings on page 47. 0 LEVEL (audio output level) switch Sets the output level of the TUNER OUTPUT connector to 28 dBm or 58 dBm. Select the setting according to the input level of the equipment connected to the tuner. qa TRS PHONE (tuner audio output) connector (1/4-inch jack) Connect to the audio input connector of a mixer or amplifier, etc. The output level from this connector is 30 dBm. Reception channel group and number Reception frequency Press the SET button. qs DC IN 9V (DC power input) connector Connect the supplied AC adapter here. 7 RF (radio frequency) indicator The color indicates the strength of the RF input signal. On in green: RF input is 25 dB*
or more. Off: RF input is less than 25 dB*. 8 SET button Press to change display parameters. For details, see Settings on page 47. 9 TUNER OUTPUT (audio output) connector (XLR type) Connect to the audio input connector of a mixer or amplifier, etc. Diversity tuner module
(URX-M1) 1 SET button Press to change display parameters. For details, see Settings on page 47. .....................................................................................................................................................................
* 0 dB = 1 VEMF 36 COPY 2 RF (radio frequency) indicator The color indicates the strength of the RF input signal. On in green: RF input is 25 dB*
or more. Off: RF input is less than 25 dB*. Reception channel group and number Reception frequency Press the SET button. 4 + (+ selection) / ( selection/
reset) buttons Press these buttons to set the reception channel and frequency. 3 Display section A B RF AF CH C A RF (radio frequency) indications The number of dots indicates the RF input level. B AF (audio frequency) indication Appears whenever the output audio signal is stronger than the reference level. C GP (group)/CH (channel) indication Shows the reception channel group and channel number. Each time you press the SET button, the channel indication changes as follows. For details, see Settings on page 47. .....................................................................................................................................................................
* 0 dB = 1 VEMF 37 COPY Power Supply Power Supply This section explains the power supply for each component. Inserting the batteries Half-rack size diversity tuner
(URX-R1) Connect the supplied AC adapter to the DC IN 9V connector on the rear panel, and then connect the AC adapter to a wall outlet. Diversity tuner module
(URX-M1) When incorporated into another component (e.g., MB-806A, SRP-
X700P, etc.), the tuner module draws its power from that component. For details on the power supply to the diversity tuner module, refer to the operating instructions of the component in which the diversity tuner module is installed. Body-pack transmitter (UTX-
B1), hand-held microphone
(UTX-H1), plug-on transmitter
(UTX-P1), and portable diversity tuner (URX-P1) These components can be powered by two LR6 (size AA) alkaline batteries for about six hours of continuous operation (at 25 C
(77F)). Details on inserting the batteries and the battery condition indication are given below:
Body-pack transmitter (UTX-
B1)/portable diversity tuner
(URX-P1) The procedure below uses the body-
pack transmitter (UTX-B1) in the illustrations. Batteries are, however, inserted in the portable diversity tuner
(URX-P1) in the same manner. 1 Slide the latches on both sides of the transmitter/tuner at the same time and open the battery compartment. Latch 2 Align two new LR6 (size AA) alkaline batteries with the polarity markings and insert them into the battery compartment, and then close the cover. 38 COPY Hand-held microphone
(UTX-H1) 1 Turn the grip in the direction of the arrow to open the battery compartment. Plug-on transmitter (UTX-P1) 1 Slide the battery cover to release the lock and open the battery compartment. 2 Align two new LR6 (size AA) alkaline batteries with the polarity markings and insert them into the battery compartment. 2 Align two new LR6 (size AA) alkaline batteries with the polarity markings and insert them into the battery compartment, and then close the cover. 3 Turn the grip in the direction opposite to the arrow in step 1 to close the battery compartment. Note If you open the battery compartment during signal transmission, the noise may occur. Be sure to turn the microphone off before opening the battery compartment. 39 COPY Power Supply Battery indication When you turn the power on, the battery condition is shown by the BATT indication in the display section. When the indication in column 4 starts to flash, replace the batteries with new ones. Be sure to check the expiration date printed on the new batteries before using them. 1 2 3 4 BATT indication Lights Lights Lights Flashes Battery status Good Less than 50% charged Less than 20% charged Almost drained Note The indicated battery condition may not be correct if the batteries were not new when installed. If you plan to use the component for a long period, it is recommended that you replace the batteries with brand new ones. Notes on batteries Batteries may leak or explode if mistreated. Be sure to follow these instructions. Be sure to install the batteries with the correct polarity. Always replace the two batteries together. Do not use different types of batteries or old and new one together. The batteries are not rechargeable. When not using the component for a long period of time, remove the batteries to avoid leakage. If the batteries do leak, clean all leakage from the battery compartment and the component. Leakage left in the compartment and the component may cause poor battery contact. If there seems to be poor battery contact, consult your Sony dealer. 40 COPY Attachment and Installation Procedures This section describes the procedures for attaching the supplied accessories to components and the installation of the diversity tuner module (URX-M1) into the MB-806A Tuner Base Unit or SRP-X700P Powered Mixer. Attaching the supplied accessories to the body-pack transmitter
(UTX-B1) Attaching the microphone Microphone (supplied) Attaching the wind screen to the microphone Insert the microphone into the hole at the bottom of the windscreen. Attaching the belt clip For a secure connection, be sure to turn and lock the connector cover. Attaching the holder clip to the microphone Push the holder clip against the bottom of the microphone until the holder clip clicks into place. Insert one end of the belt clip into one of two holes on either side of the transmitter, and then insert the other end into the hole on the other side. 41 COPY Attachment and Installation Procedures Removing the belt clip Insert a pointed object such as a ballpoint pen between the belt clip and the transmitter to make some space between them, and then remove the end of the belt clip from the hole on the side of the transmitter. Inserting the plug-on transmitter (UTX-P1) into the supplied soft case Insert the UTX-P1 into the supplied soft case with the rear side up, and close the flap. Attaching the supplied accessory to the hand-
held microphone
(UTX-H1) Attaching the microphone holder Insert the bottom part of the microphone into the holder. 42 COPY Attaching optional accessory to the plug-
on transmitter (UTX-P1) Attaching a microphone or a cable Attaching the supplied accessories to the portable diversity tuner
(URX-P1) Connecting a supplied conversion cable to the OUTPUT connector Example: XLR-BMP conversion cable
(supplied) For a secure connection, be sure to turn and lock the connector cover. Attaching the belt clip See Attaching the belt clip on page 41. Push the microphone or cable connector
(XLR-3-12C connector) against the audio input connector of the UTX-P1 until it clicks into place. Detaching a microphone or a cable Microphone or cable connector Release button Press the release button and pull off the microphone or cable slowly. 43 COPY Attachment and Installation Procedures Attaching the shoe mount adapter Attaching the microphone stand adapter After attaching the belt clip and the shoe mount adapter, insert the microphone stand adapter into the screw hole at the top of the shoe mount adapter, and then rotate the microphone stand adapter until it is securely attached. Installing the diversity tuner module (URX-M1) Notes Before installing the diversity tuner module (URX-M1), make sure the unit into which the diversity tuner module (URX-M1) will be installed is turned off. Do not install or uninstall the diversity tuner module
(URX-M1) while the unit is turned on, as this may damage the connector or cause noise. Be sure to hold the horizontal part of the belt clip with the horizontal groove on the shoe mount adapter. After attaching the belt clip, insert the shoe mount adapter between the portable diversity tuner (URX-P1) and the belt clip, with the vertical parts of the belt clip aligned with the two vertical parallel grooves on the shoe mount adapter. Then, push the shoe mount adapter in the direction of the arrow, and then catch the horizontal part of the belt clip with the horizontal groove on the shoe mount adapter to hold the belt clip in place. 44 COPY The buttons and display on the front panel of the diversity tuner module
(URX-M1) may be damaged if they are gripped too strongly. Always hold the diversity tuner module by the side. Do not put your fingers on the connectors on the rear panel of the diversity tuner module (URX-M1) or into the slot on the unit into which the diversity tuner module (URX-
M1) will be installed. Keep the diversity tuner module
(URX-M1) away from static electricity. Installing a diversity tuner module (URX-M1) into an MB-
806A Tuner Base Unit The MB-806A Tuner Base Unit can accommodate up to 6 diversity tuner modules (URX-M1). 1 Holding both sides of the diversity tuner module (URX-M1), insert it into the slot. Push it in until you hear a click. 2 To install two or more diversity tuner modules (URX-M1) , detach the necessary number of blank panels by pressing the top and bottom tabs on each panel towards each other and pulling the panel out. Then do step 1 for each module. Removing a diversity tuner module (URX-M1) On the bottom panel of the MB-806A, locate the lever corresponding to the slot of the diversity tuner module
(URX-M1) to be removed and pull the lever forward. The diversity tuner module (URX-M1) is ejected from the slot. Lever 45 COPY Attachment and Installation Procedures LINE 4 SELECT MASTER B A SCENE RECALL A B C D E F GPGP RFRF BATTBATT CHCH AFAF GPGP Diversity tuner module
(URX-M1) Installing a diversity tuner module (URX-M1) into an SRP-X700P Powered Mixer The SRP-X700P Powered Mixer can accommodate up to 2 diversity tuner modules (URX-M1). 1 Remove the tuner slot cover from the SRP-X700P and inspect the top and bottom sides of the diversity tuner module. Then, holding the tuner module on both sides, insert it into the slot. Diversity tuner module
(URX-M1) LINE 4 SELECT MASTER B A SCENE RECALL A B C D E F GP RF BATT CH AF GP Removing the diversity tuner module (URX-M1) Insert a screwdriver with a shaft diameter of between 2 to 4 mm and a shaft length of 30 mm or longer into the hole under the lower part of the tuner slot and remove the tuner module. 46 COPY Settings Setting the transmission channel The procedure below is the same for all UWP series transmitters (UTX-B1/H1/P1). Refer to the pdf files Sony Wireless Microphone System Frequency List on the supplied CD-ROM for details on the selectable channel groups and channels (for U62, U66, CE62, and CE67 models) or the supplied leaflet Sony Wireless Microphone System Frequency List (for AU66 and CE67 models). 1 Turn on the transmitter while pressing down the SET button. Keep pressing the SET button until the display section parameters that were displayed when the unit was last turned off start to flash. 2 Press the SET button repeatedly until the channel number (or frequency) indication appears. 3 Press the + or button to select the channel number (or frequency). Pressing the + button cycles the indication in the order shown in the tables in the pdf files Sony Wireless Microphone System Frequency List on the supplied CD-ROM (for U62, U66, CE62, and CE67 models) or the supplied leaflet Sony Wireless Microphone System Frequency List (for AU66 and CE67 models). Pressing the button cycles the indications in the opposite direction. Hold down the + or button to change the channel number (or frequency) faster. Notes on the European model Select the group number before selecting the channel number as follows. 1) While the left two digits are flashing, select the group number by pressing the + or button. 2) When the desired group number appears, press the SET button. The right four digits start to flash to allow the selection of the channel number. 3) Select the channel number by pressing the + or button. Group selection Channel selection Frequency selection V : + button v : button Group, channel, and frequency selection examples for CE62 model are shown. 47 COPY Settings 4 When the desired channel number
(or frequency) appears, set the POWER switch to OFF to complete the setting, or press the SET button to set other items. The results are stored in memory. The stored channel number (or frequency) will appear in the display section the next time you turn on the transmitter by setting the POWER switch to ON. Notes When you are setting the transmission channel, the transmitter cannot be used to transmit signals. Do not remove the batteries while setting the transmission channel. If they are inadvertently removed, re-
insert them immediately and redo the procedure Setting the transmission channel from step 1. Make sure that the selected channel is the same on the transmitter and tuner being used in the same system. If you turn off the transmitter and then immediately turn it on right after setting the transmission channel, the unit may not operate normally. Wait a few seconds before turning it on again. Setting the reception channel The procedure below is the same for all UWP series tuners
(URX-P1/R1/M1). 48 Refer to the pdf files Sony Wireless Microphone System Frequency List on the supplied CD-ROM for details on the selectable channel groups and channels (for U62, U66, CE62, and CE67 models) or the supplied leaflet Sony Wireless Microphone System Frequency List (for AU66 and CE67 models). 1 Press down the SET button for more than one second. Keep pressing the SET button until the display section parameters start to flash. 2 Press the SET button repeatedly until the channel group and the channel number indications appear. The channel group indication starts to flash. 3 Press the + or button to select the channel group. Pressing the + button cycles the indication in the order shown in the tables in the pdf files Sony Wireless Microphone System Frequency List on the supplied CD-ROM (for U62, U66, CE62, and CE67 models) or the supplied leaflet Sony Wireless Microphone System Frequency List (for AU66 and CE67 models). COPY Pressing the button cycles the indications in the opposite direction. Hold down the + or button to change the channel group faster. 4 When the desired channel group number appears, press the SET button. The selected group is entered. The right four digits start to flash to allow the selection of the channel number. 5 Press the + or button to select the channel number. The channel indication changes in the order shown in the tables in the pdf files Sony Wireless Microphone System Frequency List on the supplied CD-ROM
(for U62, U66, CE62, and CE67 models) or the supplied leaflet Sony Wireless Microphone System Frequency List (for AU66 and CE67 models). Example: When the channel group 00 is selected 6 When the desired channel number appears, leave the tuner for about 10 seconds until the selected channel number stops flashing and the selection is stored in memory. To select the channel by frequency indication 1 Press the SET button for more than one second. Keep pressing the SET button until the display seciton parameters start to flash. 2 Press the SET button repeatedly until the frequency indication appears and starts flashing. 3 Press the + or button to select the frequency. 4 When the desired frequency appears, leave the tuner for about 10 seconds until the selected channel frequency stops flashing and the selection is stored in memory. Notes When you are setting the reception channel, the tuner can be used to receive signals. Do not remove the batteries while setting the reception channel. If they are inadvertently removed, re-insert them immediately and redo the procedure Setting the reception channel from step 1. 49 COPY Settings Make sure that the selected channel is the same on the transmitter and tuner being used in the same system. If you turn off the tuner and then immediately turn it on right after setting the reception channel, the unit may not operate normally. Wait a few seconds before turning it on again. Detecting and selecting the available channels automatically (diversity tuner module (URX-M1) only) When multiple diversity tuner modules (URX-M1) are installed into the MB-806 to perform simultaneous multiple-channel operation, select the channel group on the tuner module installed into the slot 1 of the MB-
806, then all the tuner mudules installed into the MB-806 can be set to different channels within the selected channel group. 1 Turn off all the microphones and transmitters. 2 Select the channel group on the tuner module installed into the slot 1 of the MB-806. 3 After confirming that the channel group indication has stopped flashing (about 10 seconds after you have selected the channel group), keep pressing the + button on the tuner module installed into the slot 1 of the MB-806. 50 All the tuner modules installed into the MB-806 are set to the available channels within the selected channel group. After the automatic detection and selection of available channels finish, you can change the group and channel on each tuner module manually. Notes Do the automatic detection and selection of available channels with the channel group other than channel group 00. When there are unavailable channels due to extraneous radio wave and the channel could not be selected on some tuner modules, NO CH appears on the display of those tuner modules. If this happens, select the channel group with no interference from extraneous radio wave, and repeat the procedure above. Setting the attenuation level of the audio input The procedure below is the same for all UWP series transmitters (UTX-B1/H1/P1). The attenuation level can be set during signal transmission. 1 Do the following while there is no signal transmission. Turn on the transmitter while pressing down the SET button, and press the SET button repeatedly until the attenuation level indication appears in the display section. COPY Do the following while there is signal transmission. Press the SET button repeatedly until the attenuation level indication appears in the display section. 2 Press the + or button to select the attenuation level. The selectable range is from 0 dB to 21 dB in steps of 3 dB (the factory setting is 0 dB). 3 Do the following while there is no signal transmission. Set the POWER switch to OFF to complete the setting, or press the SET button to set other items. The results are stored in memory. The change becomes effective the next time you turn on the transmitter by setting the POWER switch to ON. Resetting the accumulated battery use time indication The procedure below is the same for all UWP series transmitters (UTX-B1/H1/P1) and the portable diversity tuner
(URX-P1). The accumulated battery use time is the total time (in hours and minutes) that the batteries have been used. It is recorded whenever the transmitter/
microphone/tuner is on. Reset the indication to 00:00 whenever you replace the batteries. 1-a For transmitters (UTX-B1/H1/
P1) Turn on the unit while pressing down the SET button. 1-bFor the portable diversity tuner (URX-P1) Press down the SET button for more than one second. Keep pressing the SET button until the display section parameters start to flash. 2 Press the SET button repeatedly until the accumulated time indication appears in the display section. 3 Press the button. The time indication resets to 00:00. While 00:00 is still displayed, you can return to previous value by pressing the + button. 4-a For transmitters (UTX-B1/H1) Set the POWER switch to OFF to complete the setting, or press the SET button to set other items. The results are stored in memory. 51 COPY Settings The change becomes effective the next time you turn on the unit by setting the POWER switch to ON. 4 Set the POWER switch to OFF to complete the setting, or press the SET button to set other items. 4-bFor the portable diversity tuner (URX-P1) Leave the tuner for about 10 seconds until the time indication stops flashing and the setting is stored in memory. Setting the RF output level The procedure below is the same for the body-pack transmitter (UTX-B1) and the hand-held microphone (UTX-
H1). You can select an RF output level of H (30 mW) or L (5 mW) in setting mode. Set the RF output level to L (5 mW) for simultaneous operation of multiple channels, and set it to H (30 mW) for long-distance operation. 1 Turn on the transmitter while pressing down the SET button. 2 Press the SET button repeatedly until the RF output level indication appears in the display section. 3 Press the + button to select H (30 mW), or press the button to select L (5 mW). 52 The results are stored in memory. The change becomes effective the next time you turn on the transmitter by setting the POWER switch to ON. Setting the monitor level (portable diversity tuner (URX-P1) only) You can set the monitor level for monitoring the tuner output within the range of 01 to 24. 1 While the parameters on the display section are not flashing, press the + or button once. The monitor level indication appears in the display section. 2 Press the + button to increase the monitor level, or press the button to decrease the level. When you leave the tuner for about two seconds or more, current monitor level setting is stored in memory and the normal display resumes. Note that monitor level setting is effective after you turn off the tuner, then turn it on again. COPY Operation The procedure below is the same for all UWP series components (UTX-B1/H1/P1 and URX-P1/R1/M1). 1 Make all necessary connections on the tuner. For examples of UWP series component connections, see System Configurations on page 54. 2 Set the transmission channel on the transmitter, and then turn off the unit. For details on setting the transmission channel, see Setting the transmission channel on page 47. 3 Turn on the tuner. The parameters that were in the display section when the tuner was last turned off appear again. Note Before turning on the tuner, turn down the volume of the equipment connected to the tuner. Otherwise, noise will be produced when the tuner is turned on. 4 Set the reception channel on the tuner. For details on setting the reception channel, see Setting the reception channel on page 48. 5 Turn on the transmitter. If noise is heard Depending on the environment where the UWP series components are installed, external noise or radio waves may disrupt transmission on certain channels. When selecting a channel under these circumstances, turn off the transmitter. Then, on the tuner, select a channel for which the RF indications do not appear in the display section or for which the RF indicator does not light up (i.e., a channel free from noise or radio wave interference). Set the same channel on the transmitter. Note To prevent interference or noise, please take the following precautions. Do not use two or more transmitters with the same wireless channels. When operating two or more UWP series simultaneously, set each series to a different channel within the same channel group. Keep the reception antenna and the transmitter separated more than 3 meters (9 feet 11 inches). When operating two or more UWP series simultaneously with the same channel group, make sure that they are at least 100 meters (330 feet) apart, but within clear sight of each other. (The actual distance may differ depending on the circumstances.) 53 COPY System Configurations System Configurations Note Production of the peripheral and relating devices may have been discontinued. Upon selecting the devices to be used with this product, consult your nearest Sony representative or the dealer from whom you purchased the product. Configuration examples of the UWP-C1/C2/S1/S2/X1/X2 Sample configurations for ENG (Electronic News Gathering) or EFP (Electronic Field Production) with a digital camcorder Portable diversity tuner (URX-P1)
(with the belt clip and the shoe mount adapter attached) Body-pack transmitter
(UTX-B1) or DVCAM Digital Camcorder (DSR-
PD170/PD170P, HVR-Z1, etc .) Portable diversity tuner (URX-P1)
(with the belt clip and the shoe mount adapter attached) Hand-held microphone
(UTX-H1) DVCAM Digital Camcorder (DSR-PD170/
PD170P, HVR-Z1, etc .) 1 XLR-BMP conversion cable (supplied) 54 COPY Sample configurations for AV presentations Portable diversity tuner (URX-P1) (with the belt clip, the shoe mount adapter, and the microphone stand adapter attached) Hand-held microphone
(UTX-H1) Body-pack transmitter
(UTX-B1) To DVD player, PC, or VTR, etc. Hand-held microphone
(UTX-H1) To DVD player, PC, or VTR, etc. or SRP-X500P/X700P Powered Mixer Half-rack size diversity tuner (URX-R1) SRP-X500P/X700P Powered Mixer AN-820 UHF antenna Diversity tuner module (URX-M1) Body-pack transmitter
(UTX-B1) 1 XLR cable with the XLR-BMP conversion cable (supplied) 2 BNC cable 3 XLR cable or pin cable 55 COPY System Configurations Sample configuration of a PA system Hand-held microphone (UTX-H1) AN-820 UHF antenna Diversity tuner module
(URX-M1) Body-pack transmitter
(UTX-B1) To DVD player, PC, or VTR, etc. SRP-X500P/X700P Powered Mixer 1 BNC cable 2 XLR cable 3 XLR cable or pin cable
*1 WD-820A Antenna Divider
*2 MB-806A Tuner Base Unit
*3 SRP-X100 Audio Mixer Diversity tuner module (URX-M1) 56 COPY Configuration example of the UWP-C3 DMX-P01 Digital Portable Mixer F-112 Dynamic Microphone or Plug-on transmitter
(UTX-P1) Portable diversity tuner
(URX-P1) (with the belt clip and the shoe mount adapter attached) or DMX-P01 Digital Portable Mixer Portable diversity tuner (URX-P1) DVCAM Digital Camcorder
(DSR-PD170/PD170P, HVR-Z1, etc.) 1 XLR cable 2 XLR cable with the stereo mini plug-BMP conversion cable (supplied) 57 COPY Error Messages Error Messages When a problem occurs, one of the following error messages may appear on the display. Messages Meanings Err 01 Err 02 An error has occurred in the backup memory data. The PLL synthesized circuit is abnormal. Remedy Contact your Sony dealer. Restart the unit. If the message appears again, contact your Sony dealer. Err 03*
The battery voltage exceeds the allowable limit. Use the specified batteries.
* Body-pack transmitter (UTX-B1)/hand-held microphone (UTX-H1)/plug-on transmitter (UTX-
P1)/portable diversity tuner (URX-P1) only. 58 COPY Troubleshooting If you have any problem using the UWP system, use the following checklist. Should any problem persist, consult your Sony dealer. Symptom The unit does not turn on*. Meanings/Remedy The polarity orientation of the batteries in the battery compartment is incorrect. b Insert the batteries with the correct polarity orientation. The batteries are exhausted. b Replace the batteries with new ones. The battery terminals in the transmitter are dirty. b Clean the + and terminals with a cotton swab. The batteries become drained quickly*. The batteries are exhausted. b Replace the batteries with new ones. The channel cannot be changed. There is no sound. The sound is weak. Manganese batteries are being used. b Use alkaline batteries. The battery life of a manganese battery is less than half that of an alkaline battery. The UWP series is being used under cold conditions. b The batteries drain quickly under cold conditions. An attempt was made to change the channel by pressing the SET button only. b Restart the unit while holding down the SET button. Then change the channel with the + and buttons. The channel setting on the transmitter is different from that on the tuner. b Use the same channel setting on both the transmitter and tuner. The RF indications (RF indicator) on the tuner do not appear at all (or does not turn on). b Confirm that the transmitter is turned on. The attenuation level on the transmitter is too high. b The output level of the transmitter is low. Press the +
button on the transmitter in attenuation level setting mode to decrease the attenuation level. The volume on the amplifier or mixer is low. b Adjust the volume.
* Body-pack transmitter (UTX-B1)/hand-held microphone (UTX-H1)/plug-on transmitter (UTX-
P1)/portable diversity tuner (URX-P1) only. 59 COPY Troubleshooting Symptom Meanings/Remedy There is distortion in the sound. There is sound interruption or noise. The attenuation level of the transmitter is too low. b The input level of the tuner is extremely high. Press the button on the transmitter in attenuation level setting mode to raise the attenuation level. The transmitter and the tuner are set to different channels. b Set the transmitter to the same channel. The RF indications on the tuner appear (the RF indicator lights up) even when the transmitter is off. b Jamming radio waves are being received. Determine which channels are usable (i.e., channels for which the RF indications on the tuner do not appear (or for which the RF indicator on the tuner does not light up) and set the tuner and transmitter to the same usable channel. When two or more transmitters are used simultaneously, use another channel group that is unaffected by jamming radio waves. The transmitter and the tuner are set to different channels. b Set the transmitter to the same channel. Two or more transmitters are set to the same channel. b Set each transmitter to a different channel. The transmitters are not set to the channels within the same channel group. b The channel plan which the UWP series components use is set so that no signal interference occurs when 2 or more transmitters are used simultaneously. Set each transmitter to a different channel within the same channel group. 60 COPY Specifications Transmitters (UTX-B1/
H1/P1) Items common to all transmitters Oscillator type Crystal-controlled PLL synthesizer Carrier frequencies Model available in USA:
758 to 806 MHz Model available in Europe:
798 to 862 MHz Model available in Australia: 792 to 806 MHz Operating frequency band Model available in USA and Europe: 24 MHz BW Model available in Australia: 14 MHz BW Pre-emphasis 50 s Frequency characteristics 50 Hz to 18 kHz Signal-to-noise ratio 60 dB or more Tone signal 32 kHz Attenuation 0 to 21 dB, in 3-dB steps Display Channel, frequency, audio level, RF level, accumulated battery use time Power requirements 3.0 V DC (two LR6/AA-
size alkaline batteries) Battery life Approx. 6 hours (measured with two Sony LR6/AA-
size alkaline batteries at 25C (77F), with output power of 30 mW (UTX-
B1/H1) or 50 mW (UTX-
P1)) Body-pack transmitter
(UTX-B1) Antenna 1/4 wave length wire Audio input connector 3.5-mm dia. mini jack Audio input level 60 dBV to 39 dBV RF output level 30 mW/5 mW selectable Reference deviation 5 kHz Distortion 1.0% or less Indicator Power on Dimensions 61 COPY Specifications 63 100 27 mm (2 1/2 4 1 1/8 inches) (w/h/d)
(excluding the antennas) Approx. 140 g (5 oz) including batteries Mass Hand-held microphone
(UTX-H1) Microphone unit Dynamic Directivity Unidirectional Antenna 1/4 wave length wire
(internal) RF output level 30 mW/5 mW selectable Reference deviation 5 kHz Distortion 1.0% or less Indicator Power on Dimensions Plug-on transmitter (UTX-P1) RF output level 50 mW Reference deviation 10 kHz Maximum deviation 40 kHz Distortion 1.0% or less at 1 kHz, 60 dBV (MIC INPUT) Audio reference level Mic: 60 dBV Line: +4 dBu Audio input connector XLR-3-11type Indicator AF/PEAK level Dimensions 52 240 mm (2 1/8 9 1/2 inches) (dia/length) Approx. 300 g (11 oz) including batteries Mass 62 44 99 36 mm (1 3/4 4 1 7/16 inches) (w/h/d)
(including the audio input connector) Approx. 185 g (6.5 oz) including batteries Mass COPY Tuners (URX-P1/R1/M1) Items common to all tuners Type of reception Space diversity Oscillator type Crystal-controlled PLL synthesizer Reception frequencies Model available in USA:
758 to 806 MHz Model available in Europe:
798 to 862 MHz Model available in Australia: 792 to 806 MHz Operating frequency band Model available in USA and Europe: 24 MHz BW Model available in Australia: 14 MHz BW Signal-to-noise ratio 60 dB or more De-emphasis 50 s Reference deviation 5 kHz Frequency characteristics 50 Hz to 18 kHz Distortion 1.0% or less at 1 kHz modulation Tone signal 32 kHz Indicator RF input level Portable diversity tuner
(URX-P1) Antenna 1/4 wave length wire
(adjustable angle) Squelch level 15 dB Audio output level 58 dBm Audio output connector 3.5 mm dia. mini jack Headphones output level 5 mW (16) Display Channel, frequency, audio level, RF level, accumulated battery use time, monitor level Power requirements 3.0 V DC (two LR6/AA-
size alkaline batteries) Battery life Approx. 6 hours (measured with two Sony LR6/AA-
size alkaline batteries at 25 C (77F)) Dimensions 63 100 30 mm (2 1/2 4 1 3/16 inches) (w/h/d)
(excluding the antennas) Mass Approx. 180 g (6 oz) including batteries 63 COPY Half-rack size diversity tuner
(URX-R1) Antenna 1/4 wave length wire
(adjustable angle) Squelch level 25 dB Audio output level 212 44 209 mm (8 3/8 1 3/4 8 1/4 inches) (w/h/d)
(excluding the antennas) Approx. 1.3 kg (2 lb 14 oz) Mass Diversity tuner module
(URX-M1) 28 dBm (LINE level)/58 Squelch level dBm (MIC level) selectable Audio output connectors 25 dB Display Channel, frequency Dimensions 1/4-inch jack, unbalanced
(LINE level only) XLR-3-32 type, balanced Headphones output level 5 mW (16) Display Channel, frequency Power requirements 9.0 V DC Dimensions 57 26 121 mm (2 1/4 1 1/16 4 7/8 inches) (w/h/d) Approx. 150 g (5 oz) Mass Design and specifications are subject to change without notice. Sony Corporation COPY
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2005-11-11 | 758.125 ~ 805.875 | TBF - Licensed Broadcast Transmitter Held to Face | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2005-11-11
|
||||
| 1 | Applicant's complete, legal business name |
Sony Corporation
|
||||
| 1 | FCC Registration Number (FRN) |
0003739166
|
||||
| 1 | Physical Address |
1-7-1 Konan
|
||||
| 1 |
Tokyo, N/A 108-0075
|
|||||
| 1 |
Japan
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
m******@ccsemc.com
|
||||
| 1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
AK8
|
||||
| 1 | Equipment Product Code |
UTXP1
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
R**** T****
|
||||
| 1 | Title |
Senior Manager
|
||||
| 1 | Telephone Number |
81-50********
|
||||
| 1 | Fax Number |
81-50********
|
||||
| 1 |
c******@jp.sony.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | TBF - Licensed Broadcast Transmitter Held to Face | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | UHF Synthesized Transmitter | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operating instructions for satisfying RF exposure compliance requirements. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Japan Qlty. Assur. Org. Kita-Kansai Testing Center
|
||||
| 1 | Name |
K****** S****
|
||||
| 1 | Telephone Number |
81-72********
|
||||
| 1 | Fax Number |
81-72********
|
||||
| 1 |
s******@jqa.jp
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 74.861 | M4 | 758.12500000 | 805.87500000 | 0.0430000 | 0.0050000000 % | 110KF3E | |||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC