3 4 5 Alp_UG.book Page 1 Monday, November 12, 2007 10:41 AM User guide English Language Language Language HBH-PV708 1 Charging connector Charging connector Indicator light Indicator light Call handling key Call handling key 2 Increase volume Increase volume Decrease volume Decrease volume Ear hook Ear hook Speaker Speaker Microphone Microphone 6 7 First time charging: about 8 hours Normal charging: about 2 hours First time charging: about 8 hours Normal charging: about 2 hours Charging Charging Fully charged Fully charged Battery needs charging Battery needs charging CLA-60/
CLA-61 CST-60/CST-70/
CST-75 CST-61 English The Bluetooth headset HBH-PV708 can be connected to any device with Bluetooth wireless technology that supports the handsfree or headset profile. This User guide focuses on usage with a Sony Ericsson mobile phone. Charging the headset Before using the HBH-PV708 for the first time, charge it with, for example, the supplied charger or your phone charger, see figure 3. For compatible chargers, see figure 4. Pairing the headset Before you can use the headset it has to be paired once with your phone. Upon a successful pairing, the headset will automatically connect to the phone as soon as it is turned on and within range. To pair the headset with your phone 1. Make sure the headset is turned off. 2. Turn on the Bluetooth function in the phone. For instructions, see the phone User guide. 3. Turn on Bluetooth visibility in the phone. This makes the phone visible to other Bluetooth devices. 4. Place the phone within 20 cm (8 inches) from the headset. 5. Press and hold down the call handling key until the headset beeps, shows a steady green light and then flashes red and green alternately. If the indicator light only flashes green or red, simultaneously press and hold down both volume keys until the headset beeps and flashes green and red alternately. 6. Press Yes when Add device? appears in the phone. If required, the passcode is 0000. The headset beeps and flashes green when successfully paired. xxx xxx xx Note: If auto pairing is not supported by your phone, or not successful, follow the first 5 steps above. Then add the headset to your phone as described in the phone User guide. The passcode is 0000. Putting on the headset See figure 5. Make sure you twist the speaker round into your ear. For left ear use, change the position of the ear hook as instructed. Turning on and off the headset To turn on the headset Press and hold down the call handling key until the indicator light shows a steady green light. It will then start flashing green. To turn off the headset Press and hold down the call handling key until the indicator light shows a steady green light. It will then turn off. Calling When you have paired the headset with your phone, you can make and receive calls as long as the headset is turned on. Solid objects, walls and a greater distance than 5 metres (16.5 feet) can affect the sound quality negatively. For best performance, wear the headset and the phone on the same side of your body. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Declaration of conformity for HBH-PV708 We, Sony Ericsson Mobile Communications AB of Nya Vattentornet SE-221 88 Lund, Sweden declare under our sole responsibility that our product Sony Ericsson type DDA-0002010 to which this declaration relates is in conformity with the appropriate standards EN 300 328:V1.7.1, EN 301 489-7:V1.3.1, EN 301 489-
17:V1.2.1 and EN 60950-1:2006 following the provisions of Radio Equipment and Telecommunication Equipment directive 1999/5/EC. Lund, September 2007 To make a call Use the phone keys, and dial the number in the same way as you would normally do. The call is automatically activated in the headset. To end a call Press the call handling key briefly. To answer a call Press the call handling key briefly. To reject a call Press and hold down the call handling key until you hear a short beep (after 2 seconds). To redial the last number Press the call handling key twice within a second. To turn off the microphone (mute) Simultaneously press both volume keys. Repeat to turn on the microphone again. Adjusting volume To adjust the ring volume When you are not engaged in a call, or while the phone is ringing, press a volume key. Jacob Sten, Head of Product Business Unit Accessories We fulfil the R&TTE Directive. We fulfil the R&TTE Directive. To adjust the speaker volume During a call, press a volume key. Language 2 Calling using voice commands Voice commands can be useful when you are using the headset and the phone is not close at hand. For more information on voice commands, see your phone User guide. To make a call using voice commands Press the call handling key briefly, wait for a beep and say your command. Note: Make sure voice commands are enabled and recorded in your phone before you try to use them. Transferring sound To transfer the sound from the phone to the headset During a call on the phone, press the call handling key briefly. The sound is transferred to the headset. To transfer the sound from the headset to the phone See the phone User guide. Resetting the headset Reset the headset if it behaves unexpectedly. To reset the headset 1. Simultaneously press and hold down both volume keys until the headset beeps and flashes red and green alternately. 2. Simultaneously press and hold down both volume keys until the headset turns off. 3. Pair the headset with the phone in the same way as you paired it the first time. Battery A battery that has been infrequently used, or a new one, could have reduced capacity. It may need to be recharged a number of times. When the battery needs charging, the indicator light flashes red and you hear a low beep. If you do not charge the headset, it automatically turns off. To check the battery status Simultaneously press both volume keys briefly:
one green flash the battery needs charging soon two green flashes the battery is medium full three green flashes the battery is fully charged Attaching the strap To attach the enclosed strap, see figure 6. Viewing regulatory information To view the regulatory information, see figure 7. Troubleshooting No connection to the phone Make sure the headset is charged and within range of the phone. Check or redo the Bluetooth settings in the phone. Try to pair the headset again. Unexpected behaviour Reset the headset. Redial does not work If the call list in the phone is empty you cannot use the redial function. Sony Ericsson Mobile Communications AB SE-221 88 Lund, Sweden 1202-2061.1 Printed in XXXXX 6 7 Alp_UG.book Page 2 Monday, November 12, 2007 10:41 AM Bluetooth Headset HBH-PV708 3 User guide User guide User guide User guide Sony Ericsson HBH-PV708 This User guide is published by Sony Ericsson Mobile Communications AB, without any warranty. Improvements and changes to this User guide necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Sony Ericsson Mobile Communications AB at any time and without notice. Such changes will, however, be incorporated into new editions of this User guide. All rights reserved. Sony Ericsson Mobile Communications AB, 2007 Publication number: 1202-2061.1 Some of the services in this User guide are not supported by all networks. This also applies to the GSM International Emergency Number 112. Contact your network operator or service provider if you are in doubt whether you can use a particular service. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Ericsson is under license. Sony and WALKMAN are trademarks or registered trademarks of Sony Corporation. Ericsson is a trademark or registered trademark of Telefonaktiebolaget LM Ericsson. This product is leadfree and halogenfree. First time charging: about 8 hours Normal charging: about 2 hours First time charging: about 8 hours Normal charging: about 2 hours Charging Charging Fully charged Fully charged Battery needs charging Battery needs charging CST-60/CST-70/
CST-75 CST-61 1 Charging connector Charging connector Indicator light Indicator light Call handling key Call handling key 2 CLA-60/
CLA-61 4 5 Increase volume Increase volume Decrease volume Decrease volume Ear hook Ear hook Speaker Speaker Microphone Microphone Language 3 The Bluetooth headset HBH-PV708 can be connected to any device with Bluetooth wireless technology that supports the handsfree or headset profile. This User guide focuses on usage with a Sony Ericsson mobile phone. Charging the headset Before using the HBH-PV708 for the first time, charge it with, for example, the supplied charger or your phone charger, see figure 3. For compatible chargers, see figure 4. Pairing the headset Before you can use the headset it has to be paired once with your phone. Upon a successful pairing, the headset will automatically connect to the phone as soon as it is turned on and within range. To pair the headset with your phone 1. Make sure the headset is turned off. 2. Turn on the Bluetooth function in the phone. For instructions, see the phone User guide. 3. Turn on Bluetooth visibility in the phone. This makes the phone visible to other Bluetooth devices. 4. Place the phone within 20 cm (8 inches) from the headset. 5. Press and hold down the call handling key until the headset beeps, shows a steady green light and then flashes red and green alternately. If the indicator light only flashes green or red, simultaneously press and hold down both volume keys until the headset beeps and flashes green and red alternately. 6. Press Yes when Add device? appears in the phone. If required, the passcode is 0000. The headset beeps and flashes green when successfully paired. xxx xxx xx Note: If auto pairing is not supported by your phone, or not successful, follow the first 5 steps above. Then add the headset to your phone as described in the phone User guide. The passcode is 0000. Putting on the headset See figure 5. Make sure you twist the speaker round into your ear. For left ear use, change the position of the ear hook as instructed. Turning on and off the headset To turn on the headset Press and hold down the call handling key until the indicator light shows a steady green light. It will then start flashing green. To turn off the headset Press and hold down the call handling key until the indicator light shows a steady green light. It will then turn off. Calling When you have paired the headset with your phone, you can make and receive calls as long as the headset is turned on. Solid objects, walls and a greater distance than 5 metres (16.5 feet) can affect the sound quality negatively. For best performance, wear the headset and the phone on the same side of your body. To make a call Use the phone keys, and dial the number in the same way as you would normally do. The call is automatically activated in the headset. To end a call Press the call handling key briefly. To answer a call Press the call handling key briefly. To reject a call Press and hold down the call handling key until you hear a short beep (after 2 seconds). To redial the last number Press the call handling key twice within a second. To turn off the microphone (mute) Simultaneously press both volume keys. Repeat to turn on the microphone again. Adjusting volume To adjust the ring volume When you are not engaged in a call, or while the phone is ringing, press a volume key. To adjust the speaker volume During a call, press a volume key. Language 4 Calling using voice commands Voice commands can be useful when you are using the headset and the phone is not close at hand. For more information on voice commands, see your phone User guide. To make a call using voice commands Press the call handling key briefly, wait for a beep and say your command. Note: Make sure voice commands are enabled and recorded in your phone before you try to use them. Transferring sound To transfer the sound from the phone to the headset During a call on the phone, press the call handling key briefly. The sound is transferred to the headset. To transfer the sound from the headset to the phone See the phone User guide. Resetting the headset Reset the headset if it behaves unexpectedly. To reset the headset 1. Simultaneously press and hold down both volume keys until the headset beeps and flashes red and green alternately. 2. Simultaneously press and hold down both volume keys until the headset turns off. 3. Pair the headset with the phone in the same way as you paired it the first time. Battery A battery that has been infrequently used, or a new one, could have reduced capacity. It may need to be recharged a number of times. When the battery needs charging, the indicator light flashes red and you hear a low beep. If you do not charge the headset, it automatically turns off. To check the battery status Simultaneously press both volume keys briefly:
one green flash the battery needs charging soon two green flashes the battery is medium full three green flashes the battery is fully charged Attaching the strap To attach the enclosed strap, see figure 6. Viewing regulatory information To view the regulatory information, see figure 7. Troubleshooting No connection to the phone Make sure the headset is charged and within range of the phone. Check or redo the Bluetooth settings in the phone. Try to pair the headset again. Unexpected behaviour Reset the headset. Redial does not work If the call list in the phone is empty you cannot use the redial function. Sony Ericsson Mobile Communications AB SE-221 88 Lund, Sweden 1202-2061.1 Printed in XXXXX