FCC ID: PY7-65375K GSM/WCDMA/LTE Phone with BT, DTS/UNII a/b/g/n/ac/ax, GPS, WPC and NFC

Safety Guidelines Important information about hearing aid compatibility FCC Statement Safety Guidelines Before a device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (i.e., at the ear and worn on the body) as required by the FCC for each model. Body worn measurements are made while the device is in use and worn on the body with a Sony Mobile accessory. The design and composition of an accessory can affect the body worn Specific Absorption Rate (SAR) levels for the device. Sony Mobile has not measured, and makes no representation about, the body worn SAR levels when the device is used with non-Sony Mobile accessories. Consumer Update on Wireless Devices Supplied by the U.S. Food and Drug Administration (FDA) - Center for Devices and Radiological Health Do wireless devices pose a health hazard?

The available scientific evidence does not show that any health problems are associated with using wireless devices. There is no proof, however, that wireless devices are absolutely safe. Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. They also emit very low levels of RF when in the stand-by mode. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low level RF that does not produce heating effects causes no known adverse health effects. Many studies of low level RF exposures have not found any biological effects. Some studies have suggested that some biological effects may occur, but such findings have not been confirmed by additional research. In some cases, other researchers have had difficulty in reproducing those studies, or in determining the reasons for inconsistent results. What is FDAs role concerning the safety of wireless devices?

Under the law, FDA does not review the safety of radiation-emitting consumer products such as wireless devices before they can be sold, as it does with new drugs or medical devices. However, the agency has authority to take action if wireless devices are shown to emit radio frequency energy (RF) at a level that is hazardous to the user. In such a case, FDA could require the manufacturers of wireless devices to notify users of the health hazard and to repair, replace or recall the devices so that the hazard no longer exists. Although the existing scientific data do not justify FDA regulatory actions, FDA has urged the wireless device industry to take a number of steps, including the following:

Support needed research into possible biological effects of RF of the type emitted by wireless devices;

Design wireless devices in a way that minimizes any RF exposure to the user that is not necessary for device function; and Cooperate in providing users of wireless devices with the best possible information on possible effects of wireless device use on human health. FDA belongs to an interagency working group of the federal agencies that have responsibility for different aspects of RF safety to ensure coordinated efforts at the federal level. The following agencies belong to this working group:

National Institute for Occupational Safety and Health Environmental Protection Agency Federal Communications Commission Occupational Safety and Health Administration National Telecommunications and Information Administration The National Institutes of Health participates in some interagency working group activities, as well. FDA shares regulatory responsibilities for wireless devices with the Federal Communications Commission (FCC). All devices that are sold in the United States must comply with FCC safety guidelines that limit RF exposure. FCC relies on FDA and other health agencies for safety questions about wireless devices. FCC also regulates the base stations that the wireless device networks rely upon. While these base stations operate at higher power than do the wireless devices themselves, the RF exposures that people get from these base stations are typically thousands of times lower than those they can get from wireless devices. Base stations are thus not the subject of the safety questions discussed in this document. What kinds of devices are the subject of this update?

The term wireless device refers here to hand-held wireless devices with built-in antennas, often called cell, mobile, or PCS devices. These types of wireless devices can expose the user to measurable radio frequency energy (RF) because of the short distance between the device and the users head. These RF exposures are limited by Federal Communications Commission safety guidelines that were developed with the advice of FDA and other federal health and safety agencies. When the device is located at greater distances from the user, the exposure to RF is drastically lower because a persons RF exposure decreases rapidly with increasing distance from the source. The so-called cordless devices, which have a base unit connected to the telephone wiring in a house, typically operate at far lower power levels, and thus produce RF exposures far below the FCC safety limits. What are the results of the research done already?

The research done thus far has produced conflicting results, and many studies have suffered from flaws in their research methods. Animal experiments investigating the effects of radio frequency energy (RF) exposures characteristic of wireless devices have yielded conflicting results that often cannot be repeated in other laboratories. A few animal studies, however, have suggested that low levels of RF could accelerate the development of cancer in laboratory animals. However, many of the studies that showed increased tumor development used animals that had been genetically engineered or treated with cancer-causing chemicals so as to be pre-disposed to develop cancer in the absence of RF exposure. Other studies exposed the animals to RF for up to 22 hours per day. These conditions are not similar to the conditions under which people use wireless devices, so we dont know with certainty what the results of such studies mean for human health. Three large epidemiology studies have been published since December 2000. Between them, the studies investigated any possible association between the use of wireless devices and primary brain cancer, glioma, meningioma, or acoustic neuroma, tumors of the brain or salivary gland, leukemia, or other cancers. None of the studies demonstrated the existence of any harmful health effects from wireless device RF exposures. However, none of the studies can answer questions about long-term exposures, since the average period of device use in these studies was around three years. What research is needed to decide whether RF exposure from wireless devices poses a health risk?

A combination of laboratory studies and epidemiological studies of people actually using wireless devices would provide some of the data that are needed. Lifetime animal exposure studies could be completed in a few years. However, very large numbers of animals would be needed to provide reliable proof of a cancer promoting effect if one exists. Epidemiological studies can provide data that is directly applicable to human populations, but 10 or more years follow-up may be needed to provide answers about some health effects, such as cancer. This is because the interval between the time of exposure to a cancer-causing agent and the time tumors develop - if they do - may be many, many years. The interpretation of epidemiological studies is hampered by difficulties in measuring actual RF exposure during day-to-day use of wireless devices. Many factors affect this measurement, such as the angle at which the device is held, or which model of device is used. What is FDA doing to find out more about the possible health effects of wireless device RF?

FDA is working with the U.S. National Toxicology Program and with groups of investigators around the world to ensure that high priority animal studies are conducted to address important questions about the effects of exposure to radio frequency energy (RF). FDA has been a leading participant in the World Health Organization International Electromagnetic Fields (EMF) Project since its inception in 1996. An influential result of this work has been the development of a detailed agenda of research needs that has driven the establishment of new research programs around the world. The Project has also helped develop a series of public information documents on EMF issues. FDA and the Cellular Telecommunications & Internet Association (CTIA) have a formal Cooperative Research and Development Agreement (CRADA) to do research on wireless device safety. FDA provides the scientific oversight, obtaining input from experts in government, industry, and academic organizations. CTIA-funded research is conducted through contracts to independent investigators. The initial research will include both laboratory studies and studies of wireless device users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world. How can I find out how much radio frequency energy exposure I can get by using my wireless device?

All devices sold in the United States must comply with Federal Communications Commission (FCC) guidelines that limit radio frequency energy (RF) exposures. FCC established these guidelines in consultation with FDA and the other federal health and safety agencies. The FCC limit for RF exposure from wireless telephones is set at a Specific Absorption Rate (SAR) of 1.6 watts per kilogram (1.6 W/kg). The FCC limit is consistent with the safety standards developed by the Institute of Electrical and Electronic Engineering (IEEE) and the National Council on Radiation Protection and Measurement. The exposure limit takes into consideration the bodys ability to remove heat from the tissues that absorb energy from the wireless device and is set well below levels known to have effects. Manufacturers of wireless devices must report the RF exposure level for each model of device to the FCC. The FCC website (http://www.fcc.gov/oet/rfsafety) gives directions for locating the FCC identification number on your device so you can find your devices RF exposure level in the online listing. Hearing Aid Compatibility FCC Statement What has FDA done to measure the radio frequency energy coming from wireless devices?

The Institute of Electrical and Electronic Engineers (IEEE) is developing a technical standard for measuring the radio frequency energy (RF) exposure from wireless devices and other wireless handsets with the participation and leadership of FDA scientists and engineers. The standard, Recommended Practice for Determining the Spatial-Peak Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques, sets forth the first consistent test methodology for measuring the rate at which RF is deposited in the heads of wireless device users. The test method uses a tissue-simulating model of the human head. Standardized SAR test methodology is expected to greatly improve the consistency of measurements made at different laboratories on the same device. SAR is the measurement of the amount of energy absorbed in tissue, either by the whole body or a small part of the body. It is measured in watts/kg (or milliwatts/g) of matter. This measurement is used to determine whether a wireless device complies with safety guidelines. What steps can I take to reduce my exposure to radio frequency energy from my wireless device?

If there is a risk from these products--and at this point we do not know that there is--it is probably very small. But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radio frequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless device will reduce RF exposure. If you must conduct extended conversations by wireless device every day, you could place more distance between your body and the source of the RF, since the exposure level drops off dramatically with distance. For example, you could use a headset and carry the wireless device away from your body or use a wireless device connected to a remote antenna. Again, the scientific data do not demonstrate that wireless devices are harmful. But if you are concerned about the RF exposure from these products, you can use measures like those described above to reduce your RF exposure from wireless device use. What about children using wireless devices?

The scientific evidence does not show a danger to users of wireless devices, including children and teenagers. If you want to take steps to lower exposure to radio frequency energy (RF) , the measures described above would apply to children and teenagers using wireless devices. Reducing the time of wireless device use and increasing the distance between the user and the RF source will reduce RF exposure. Some groups sponsored by other national governments have advised that children be discouraged from using wireless devices at all. For example, the government in the United Kingdom distributed leaflets containing such a recommendation in December 2000. They noted that no evidence exists that using a wireless device causes brain tumors or other ill effects. Their recommendation to limit wireless device use by children was strictly precautionary; it was not based on scientific evidence that any health hazard exists. What about wireless device interference with medical equipment?

Radio Frequency energy (RF) from wireless devices can interact with some electronic devices. For this reason, FDA helped develop a detailed test method to measure electromagnetic interference (EMI) of implanted cardiac pacemakers and defibrillators from wireless telephones. This test method is now part of a standard sponsored by the Association for the Advancement of Medical instrumentation (AAMI). The final draft, a joint effort by FDA, medical device manufacturers, and many other groups, was completed in late 2000. This standard will allow manufacturers to ensure that cardiac pacemakers and defibrillators are safe from wireless device EMI. FDA has tested hearing aids for interference from handheld wireless devices and helped develop a voluntary standard sponsored by the Institute of Electrical and Electronic Engineers (IEEE). This standard specifies test methods and performance requirements for hearing aids and wireless devices so that no interference occurs when a person uses a compatible device and a compatible hearing aid at the same time. This standard was approved by the IEEE in 2000. FDA continues to monitor the use of wireless devices for possible interactions with other medical devices. Should harmful interference be found to occur, FDA will conduct testing to assess the interference and work to resolve the problem. Where can I find additional information?

For additional information, please refer to the following resources:

FDA web page for Radiation-Emitting Products (https://

www.fda.gov/Radiation-EmittingProducts/

RadiationSafety/default.htm) Federal Communications Commission (FCC) RFSafety Program (http://www.fcc.gov/oet/rfsafety) International Commission on Non-Ionizing Radiation Protection (https://www.icnirp.org/) World Health Organization (WHO) International EMF Project (http://www.who.int/emf) National Radiological Protection Board (UK) (http://www. nrpb.org.uk/) Hearing Aid Compatibility Your phone is designed for Hearing Aid Compatibility (HAC) and can be used with hearing aids. Hearing Aid Settings You can choose the setting in the phone to match the setting in your hearing aid before making or receiving calls. To Select a Phone Setting for HAC 1. From the Home screen, tap 2. Tap an option menu > Settings > Calls > Accessibility. 3. Tap the on/off switch to turn on hearing aid

. compatibility. Hearing Aid Compatibility Information This phone has been tested and rated for use with hearing aids for some of the wireless technologies it uses. This phone complies with HAC requirements for pre-installed Google applications. However, there may be some newer wireless technologies used in this phone that have not been tested yet for use with hearing aids. It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Consult your service provider or the manufacturer of this phone for information on hearing aid compatibility. If you have questions about return or exchange policies, consult your service provider or phone retailer. Hearing Aid Compatibility Rating This model handset was designed to comply with the requirements set forth in Section 20.19 of the Federal Communication Commissions (FCC) rules governing hearing aid compatibility (HAC), for the reduction of RF interference and magnetic coupling (T-coil) to hearing aids. The Microphone (M) rating and T-coil (T) rating is defined and labeled on the handset box. Devices meeting HAC compliance must have a minimum M3 and/or T3 rating or above as defined by the FCC in accordance with the latest ANSI Standard C63.19. The (M) rating refers to lower RF emission levels of the handset. The (T) rating refers to the magnetic coupling between the handset and the T-coil compatible hearing aid. Some hearing aids are also provided an (M) rating, and are more immune than others to interference. To determine the (M) rating of your hearing aid, please contact your hearing health professional. More information about digital wireless devices and hearing aid compatibility can be found at http://blogs.sonymobile. com/about-us/sustainability/accessibility/overview/

hearing-aid-compatibility/. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any change or modification not expressly approved by Sony may void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. United States 1 855 806 8464 www.sony.com/contact Printed in XXX (Printers logotype)

1 SIM XQ-AT51 OR XQ-AT52 2 PWR ON Startup guide vodn pruka Kurzanleitung Installationsvejledning Alustusjuhend Gua de inicio Aloitusopas Guide de dmarrage Prirunik Hasznlatbavteli tmutat Rsihandbk Guida introduttiva Paleisties vadovas Skanas cevedis Opstartgids Oppstartsveiviser Instrukcja obsugi Manual de Iniciao Ghid de pornire Starthandbok Vodi za zaetek uporabe vodn prruka XQ-AT51/XQ-AT52 Printed in XXX (Printers logotype) OR https://rd1.sony.net/help/mobile/xperia-1m2/h_zz/

501902331_PDX203_SG leaflet RoW_GB ES RU UA KZ TH CT

- https://www.sonymobile.com/global-en/legal/.

FCC.

, (SAR)

(SAR) ,

[KZ]

Sony Mobile Communications Inc. Sony Mobile Communications Inc.

- : https://www.sonymobile.com/global-en/legal/.

(, FCC

, SAR

, SAR ( )

. Sony Mobile Communications Inc. Sony Mobile

[TH]

Communications Inc.

https://www.sonymobile.com/global-en/legal/

FCC ID

, SAR

, SAR (

[CT]

Sony Mobile Communications Inc. Sony Mobile Communications Inc.

https://www.sonymobile.com/global-en/legal/

FCC ID SAR SAR

Sony Mobile Communications Inc. 2020 Sony Mobile Communications Inc. Declaration of Conformity PM-1260-BV (XQ-AT51) / PM-1261-BV (XQ-AT52)

[GB] Hereby, Sony Mobile declares that this equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

http://www.compliance.sony.eu/

[GB] Notice for customers: the following information is only applicable to equipment sold in countries applying EU directives This product has been manufactured by or on behalf of Sony Mobile Communications Inc. EU Importer: Sony Europe B.V. Inquiries to the EU Importer or related to product compliance in Europe should be sent to the manufacturers authorized representative, Sony Belgium, bijkantoor van Sony Europe B.V., Da Vincilaan 7-D1, 1930 Zaventem, Belgium. Supported frequency bands XQ-AT51/XQ-AT52 For customers in countries/regions other than the United States:

UMTS HSPA+ (Bands 1, 2, 4, 5, 6, 8, 19) GSM GPRS/EDGE 850, 900, 1800, 1900 LTE (Bands 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 19, 20, 25, 26, 28, 29, 32, 34, 38, 39, 40, 41, 46, 66) 5GNR (n1, n3, n28, n77, n78) WLAN, 2.4GHz/5GHz, NFC GSM 850/900 : 33dBm, DCS(1800)/PCS(1900) : 30dBm, UMTS : 24dBm, LTE : 24dBm, 5GNR : 24dBm, 2.4GHz<100mW, 5.15-5.35GHz<200mW, 5.47-5.725GHz<200mW, 5.735-5.835GHz<25mW, NFC 13.56MHz For customers in the United States:

UMTS HSPA+ (Bands 1, 2, 4, 5, 6, 8, 19) GSM GPRS/EDGE 850, 900, 1800, 1900 LTE (Bands 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 19, 20, 25, 26, 28, 29, 32, 34, 38, 39, 40, 41, 46, 66) WLAN, 2.4GHz/5GHz, NFC GSM 850/900 : 33dBm, DCS(1800)/PCS(1900) : 30dBm, UMTS : 24dBm, LTE : 24dBm, 2.4GHz<100mW, 5.15-5.35GHz<200mW, 5.47-5.725GHz<200mW, 5.735-5.835GHz<25mW, NFC 13.56MHz

[GB] For customers in countries/regions other than the United States and Singapore:

The 5150 5350MHz band is restricted to indoor use only.

[CT]

5150 5350MHz

[GB] Supported frequency bands Some frequency bands might be turned off in certain markets or by certain operators. You can find your model number under Settings > About phone.

[ES] Bandas de frecuencia admitidas Es posible que algunas bandas de frecuencia estn desactivadas en determinados mercados o por operadores especficos. Puede consultar el nmero de modelo en Ajustes > Informacin del telfono.

[RU]

[UA]

[KZ]

[TH]

[CT]

For the XQ-AT52

[GB] 5G network connectivity is supported in Single SIM Activated mode only.

[CT] 5G FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. For additional information, please read the FCC Statement provided under Settings > About phone > Legal information > Important information >

Declaration of Conformity and statements on your device. High-temperature warning

[GB] High-temperature warning This mark is displayed when the surface temperature of the product rises during use. When the mark is displayed, there is a risk of burns if you continue using the product while holding it in your hands. In this case, please refrain from holding it in your hands.

[ES] Advertencia de temperatura alta Esta marca aparece cuando la temperatura superficial del producto aumenta durante su uso. Cuando esta marca aparece, significa que existe el riesgo de quemaduras si se contina usando y sosteniendo el producto con la mano. En tal caso, deje de sostener el producto con la mano.

[RU]

[UA]

[KZ]

[TH]

[CT]

Loudness warning

[GB] Loudness warning To prevent possible hearing damage, do not listen at high volume levels for long periods.

[ES] Advertencia de volumen alto Para evitar posibles daos auditivos, no escuche el sonido a niveles de volumen elevado durante periodos prolongados.

[RU]

[UA]

[KZ]

[TH]

[CT]

[GB] Legal information This Startup guide is published by Sony Mobile Communications Inc. or its local affiliated company, without any warranty. Improvements and changes to this Startup guide necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Sony Mobile Communications Inc. at any time and without notice. Such changes will, however, be incorporated into new editions of this Startup guide. All illustrations are for illustration only and may not accurately depict the actual device. All product and company names mentioned herein are the trademarks or registered trademarks of their respective owners. Any rights not expressly granted herein are reserved. Visit https://www.sonymobile.com/global-en/legal/ for more information. To view the regulatory compliance mark Find and tap Settings > About phone > Certificates. A regulatory compliance mark such as an FCC ID is displayed on the screen. Warranty, SAR and usage guidelines For information about warranty, SAR (Specific Absorption Rate) and safety guidelines, please read the Important information provided under Settings > About phone > Legal information on your device. Note: Sony Mobile advises users to backup their personal data and information. Some services are network- or subscription-dependent. Please contact your network operator or our call center for details. For customers in the United States Owners record The model and IMEI numbers are located on the box of the unit. Record the IMEI number in the space provided below. Refer to them whenever you call upon Sony Mobile Customer Support regarding this product. Model No. _______________ IMEI No. _______________ RECYCLING RECHARGEABLE BATTERIES Rechargeable batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, visit www.sony.com/electronics/eco/environmental-management Caution: Do not handle damaged or leaking rechargeable batteries. Class I Laser Product Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. factory ID: STTB

[ES] Informacin legal Esta Gua de inicio ha sido publicada por Sony Mobile Communications Inc. o por su empresa local afiliada sin ninguna garanta. Sony Mobile Communications Inc. puede realizar, en cualquier momento y sin previo aviso, las mejoras y los cambios que sean necesarios en esta Gua de inicio a causa de errores tipogrficos, falta de precisin en la informacin actual o mejoras de los programas y los equipos. No obstante, estos cambios se incorporarn en las nuevas ediciones de la Gua de inicio. Todas las ilustraciones son solo una referencia y no constituyen una descripcin exacta del dispositivo. Todos los nombres de productos y empresas mencionados en el presente documento son marcas comerciales o marcas registradas de sus respectivos propietarios. Quedan reservados todos los derechos no mencionados expresamente en el presente documento. Visite https://www.sonymobile.com/global-en/legal/ para obtener ms informacin. Para ver la marca de conformidad normativa Busque y puntee Ajustes > Informacin del telfono > Certificados. En la pantalla aparece una marca de conformidad normativa, tal como un ID de la FCC. Garanta, SAR y directrices de uso Para obtener informacin sobre la garanta, la SAR (Tasa de absorcin especfica) y las directrices de seguridad, consulte la Informacin importante, incluida en Ajustes > Informacin del telfono > Informacin legal en el dispositivo.

[RU]

Sony Mobile Communications Inc. -

. Sony Mobile Communications Inc.

https://www.sonymobile.com/global-en/legal/.

, FCC, .

, SAR

(SAR)

[UA]

Sony Mobile Communications Inc. Sony Mobile Communications Inc. -

XXXXX Radio wave exposure and Specific Absorption Rate (SAR) information United States THIS PHONE MODEL HAS BEEN CERTIFIED IN COMPLIANCE WITH THE GOVERNMENTS REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. The XXXXX mobile phone has been designed to comply with the applicable safety requirements for exposure to radio waves. Your wireless phone is a radio transmitter and receiver. It is designed to not exceed the limits of exposure to radio frequency (RF) energy set by governmental authorities. These limits establish permitted levels of RF energy exposure for the general population. The guidelines are based on standards that were developed by international scientific organizations through periodic and thorough evaluation in scientific studies. The standards include a safety margin designed to assure the safety of all individuals, regardless of age and health. The radio wave exposure guidelines employ a unit of measurement known as the Specific Absorption Rate (SAR). Tests for SAR are conducted using standardised methods with the phone transmitting at its highest certified power level in all used frequency bands. While there may be differences between the SAR levels of various phone models, they are all designed to meet the relevant guidelines for exposure to radio waves. The highest SAR value as reported to the authorities for this phone model when tested for use by the ear is 0.41 W/kg and when worn on the body is 0.48 W/kg and for WiFi hotspot mode is 0.77 W/kg. For body-worn operation, the phone has been tested when positioned a minimum of 15 mm from the body without any metal parts in the vicinity of the phone or when properly used with an appropriate accessory and worn on the body. For devices which include WiFi hotspot functionality, SAR measurements for the device operating in WiFi hotspot mode were taken using a separation distance of 10 mm. Use of third-

party accessories may result in different SAR levels than those reported. Before a phone model is available for sale to the public in the US, it must be tested and certified by the Federal Communications Commission (FCC) that it does not exceed the government-adopted requirement for safe exposure. The tests are performed in positions and limit established by the 2 locations (i.e., by the ear and worn on the body) as required by the FCC for each model. The FCC has granted an Equipment Authorization for this phone model with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. While there may be differences between the SAR levels of various phones, all mobile phones granted an FCC equipment authorization meet the government requirement for safe exposure. SAR information on this phone model is on file at the FCC and can be found under the Display Grant section of http://transition.fcc.gov/oet/ea/fccid/ after searching on FCC ID PY7-65375K. Additional information on SAR can be found on the Mobile Manufacturers Forum EMF website at http://

www.emfexplained.info/.

* In the United States, the SAR limit for mobile phones used by the public is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The standard incorporates a margin of safety to give additional protection for the public and to account for any variations in measurements. 3

Sony Mobile Communications Prepared by:

Contents responsible if other than preparer:

Approved by:

Internal Use Only General Document number:

000228821 Date:

12 Remarks:

1(1) Revision:

1 E-Label and Label Location PY7-65375K 1 E-Label Location Users can access the FCC ID information within 3 step as the followings. Setting from Main Menu Settings -> About Phone -> Certificates FCC ID: PY7-65375K 2 Access to the required information on the e-label

(1) The user manual directs the user where to find the FCC ID E-Label. To view the regulatory compliance mark Find and tap [Settings]->[About Phone]->[Certificates]

Regulatory compliance mark such as FCC ID is displayed on the screen. Special codes or permissions are not required the above steps beyond the normal security protection to unlock the screen.

(2) Products must not require special accessories or supplemental plug-ins.

(3) The regulatory information is clearly legible without the aid of magnification.

(4) The regulatory information is secure. The user can not access and modify the regulatory information.

(5) The physical temporary label or the label on the packaging for purchasing and importation is attached in case of the device is sold in the United States. 3 FCC Statement FCC15.19(a) statement can be seen in the manual. It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

Sony Mobile Communications, Inc. 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan Remarks This document is managed in Infodoc. Date: March 19, 2020 SPORTON INTERNATIONAL, INC No. 52, Hwa Ya 1st Road Hwa Ya Technology Park Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan R.O.C FCC ID: PY7-65375K To Whom It May Concern:

Authorization Letter for Sporton I, the undersigned, hereby authorize Sporton to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Sporton on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing Sporton as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use. Sony Mobile Communications, Inc. 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan Remarks This document is managed in Infodoc. f) use certification only to indicate the products are certified as being in conformity with specified standards;

manner;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. Yours sincerely, ________________________________ Tomonori Nagano Head of Type Approval, Product Compliance Quality Assurance & Customer Services Sony Mobile Communications Inc. It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

Remarks This document is managed in Infodoc. Sony Mobile Communications, Inc. 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan Date: January 16, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To Whom It May Concern:

Power of Attorney for FCC applications Below individual is hereby authorized to sign applications, attestations and cover letters in regards of Sony Mobile Communications INC. applications, Grantee Code PY7. Tomonori Nagano Senior Manager Sony Mobile Communications Inc. Tel: +81367103241 Address: 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan E-mail: Tomonori.Nagano@sony.com Yours sincerely, ________________________________ Mika Kaneko Chief Regulatory Compliance Manager Sony Mobile Communications Inc. Tel: +81 3 6710 3225 Address: 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan E-mail: mika.kaneko@sony.com It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

Sony Mobile Communications, Inc. 4-12-3 Higashi-shinagawa, Shinagawa-ku, Tokyo, 140-0002, Japan Remarks This document is managed in Infodoc. Date: March 19, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 FCC ID: PY7-65375K To Whom It May Concern:

Confidentiality Request Letter Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely.

- Schematic Diagram

- Block Diagram

- Theory of Operation

- Antenna Specification

- Parts List

- Tune up Information Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180days from date of the Grant of Equipment Authorization.

- External Photos

Internal Photos

- Test Setup Photos

- User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Yours sincerely, ________________________________ Tomonori Nagano Head of Type Approval, Product Compliance Quality Assurance & Customer Services Sony Mobile Communications Inc. It is the responsibility of the user to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.

Sony Mobile Communications Prepared by:

Contents responsible if other than preparer:

Approved by:

Public General Document number:

000229033 Date:

2020-04-02 Remarks:

1(1) Revision:

2 PY7-65375K Data Reuse justification and summary Sony Mobile Communications Inc., hereby declares FCC ID PY7-65375K (variant model) and FCC ID PY7-87261H (parent model) share the same PCB layout, antennas and most of the components. The difference between PY7-65735K and PY7-87261H is described in the appendix of the technical description. The unlicensed band data for the parent model remains representative for the variant model (equipment classes DSS, DTS and NII) and test reports for the parent model PY7-87261H plus spot check reports for the variant model have been submitted. The power to be listed on the F-731 and FCC grants for these bands are the values detailed in the parent report as the spot check data shows all values within expected tolerances of parent model. For the licensed bands (equipment class PCE) we have submitted test reports for the parent model and variant model. The variant model report has full test data for the new bands and the bands with higher power than the parent model plus spot check data for the bands that are common to parent and variant. The power to be listed on the F-731 and FCC grants for the PCE bands are the values detailed in the parent report for the common bands and from variant report for the new bands and bands with increased radiated / conducted power. FCC ID PY7-87261H Parent PY7-65375K Variant LTE WCDMA GSM 2 4 5 7 12 13 17 25 26 41 46 66 II IV V Test Report: FG9O1542-0B Parts 22/24/27 850 1900 FG9O1542-02A Parts 22/24 FG9O1534-03A for parts 22/24/27 Test Report: FG9O1534-03C for band 26 Part 90 Test Report: FG9O1534-03B for Parts 22/24/27 Indicates full set of test data. Values in this report to be listed on the grant for these bands. Partial test data used to confirm that parent model data is representative for the variant model. Data for these bands is for reference only Partial test data for test cases affected by increase in conducted and radiated power or increase in radiated power. Values in this report to be listed on the grant for these bands. Bands not supported in the parent model Band is downlink only SAR, HAC have been fully tested on the variant model. r to ensure that they have a correct and valid version. Any outdated hard copy is invalid and must be removed from possible use.