FCC ID: PY7-RD0050 Smart Watch

Startup guideSmartWatch 2SW2Sony Mobile Communications ABSE-221 88 Lund, Swedenwww.sonymobile.comXXXX-XXXX.1BasicsChargingBefore using your SmartWatch 2 for the first time, youneed to charge it for approximately 30 minutes. Sonychargers/USB cables are recommended.To charge your SmartWatch 21Plug one end of the USB cable into the charger or intothe USB port of a computer.2Plug the other end of the cable into the Micro USB portof your SmartWatch 2.A charger may not be included at purchase in allmarkets.Overview17823645 1. Light sensor2. Power key3. Actions key4. Home key5. Back key6. Touchscreen7. NFC detection area8. Port for charger/USB cableTurning on and offTo turn on your SmartWatch 2Press and hold down the power key until thedisplay turns on.To turn off your SmartWatch 2When the display is active, press and hold down thepower key until the display turns off.Setting up yourSmartWatch 2The quickest way to get started with your SmartWatch 2 isby connecting it to your device using NFC. If your devicedoes not support NFC, you can connect manually.Setting up using NFCTo save data costs, make sure that your device isconnected to a Wi-Fi network.1Device: Make sure that the NFC function is turned onand that the screen is active and unlocked.2SmartWatch 2: Turn on your SmartWatch 2.3If the Smart Connect application is not pre-installed onyour device, place the device over the back of yourSmartWatch 2 so that the NFC detection area of eachdevice touches each other. Then follow the instructionsthat appear on the device's screen to install the SmartConnect application from Google Play.4One-touch pair and connect by placing the device overthe back of your SmartWatch 2 so that the NFCdetection area of each device touches each other.5Device: Accept the pairing request from SmartWatch 2.6Device: Follow the instructions to install the SmartWatch2 application from Google Play. Then SmartWatch 2restarts automatically to finish setting up.Setting up manuallyIf your device does not support NFC, you can connectmanually using Bluetooth function.To set up using the Bluetooth functionTo save data costs, make sure that your device isconnected to a Wi-Fi network.1Device: Make sure that you have the Smart Connectapplication, which is available on Google Play,installed on your device.2Device: Make sure that the Bluetooth function isturned on.3SmartWatch 2: Turn on your SmartWatch 2.4Device: Scan for Bluetooth devices, then selectSmartWatch 2 in the list of available devices.5Device: Accept the pairing request from SmartWatch2.6Device: Follow the instructions to install theSmartWatch 2 application from Google Play.SmartWatch 2 restarts automatically when theapplication is installed.Getting to know yourSmartWatch 2You can use your SmartWatch 2 as a regular watch andaccess most applications when it is not connected to adevice. When it is connected, you get a richer set offunctions.Installing extra applicationsInstall extra applications via the Smart Connect applicationon the Android device to optimise the functionality ofyour SmartWatch 2.To install an extra application1SmartWatch 2: Find and tap the App recommender icon.2SmartWatch 2: Select an application in the list ofrecommended applications, then tap View & install.3Device: When Google Play opens, tap install.4Device: Follow the instructions that appear on thescreen to install the application that you selected. Anicon of the application shows on the screen ofSmartWatch 2 after the installation is completed.Support on the webVisit www.sonymobile.com/support to get the most fromyour accessory, including Troubleshooting and a Userguide for your SmartWatch 2. Sony SW2Prior to use, please read the Important information leafletseparately provided.This User guide is published by Sony Mobile Communications AB or its localaffiliated company, without any warranty. Improvements and changes to this Userguide necessitated by typographical errors, inaccuracies of current information, orimprovements to programs and/or equipment, may be made by Sony MobileCommunications AB at any time and without notice. Such changes will, however,be incorporated into new editions of this User guide.All rights reserved.Sony Mobile Communications AB, 2013Publication number: XXXX-XXXX.1Interoperability and compatibility among Bluetooth devices varies. Devicegenerally supports products utilizing Bluetooth spec. 1.2 or higher, and Headset orHandsfree profile.Sony is the trademark or registered trademark of Sony Corporation. Bluetooth isthe trademark of the Bluetooth (SIG) Inc. and is used under license. All othermarks are the property of their respective owners. All rights reserved.All product and company names mentioned herein are the trademarks orregistered trademarks of their respective owners. Any rights not expressly grantedherein are reserved. All other trademarks are property of their respective owners.Visit www.sonymobile.com for more information.All illustrations are for illustration only and may not accurately depict the actualaccessory.Declaration of Conformity forSW2We, Sony Mobile Communications AB ofNya VattentornetSE-221 88 Lund, Swedendeclare under our sole responsibility that our productSony type RD-0050and in combination with our accessories, to which thisdeclaration relates is in conformity with the appropriatestandards EN 300 328:V1.7.1, EN 301 489-17:V2.1.1, EN301 489-3:V1.4.1 and EN 60 950-1:2006+A11:2009+A1:2010 following the provisions of, RadioEquipment and Telecommunication Terminal Equipmentdirective 1999/5/EC.Lund, July 2013Anders GryngeDirector, Head of Global Type ApprovalWe fulfil the requirements of the R&TTE Directive (1999/5/EC).FCC StatementThis device complies with Part 15 of the FCC rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation.Any change or modification not expressly approved by Sony may void the user'sauthority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.Consult the dealer or an experienced radio/TV technician for help.Industry Canada StatementThis device complies with RSS-210 of Industry Canada.Operation is subject to the following two conditions: (1) this device may notcause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numrique de la classe B est conforme la norme NMB-003 duCanada.Avis dindustrie CanadaLe prsent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence.L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil nedoit pas produire de brouillage, et, and (2) l'utilisateur de l'appareil doitaccepter tout brouillage radiolectrique subi, mme si le brouillage estsusceptible d'en compromettre le fonctionnement.www.sonymobile.com

Prepared by HW PM Daniel Flinck Contents responsible if other than preparer Approved by HW PM Daniel Flinck Company Internal Specification Document number 1275-3715 Date 2013-07-11 Remarks This document is handled in SPACE Type number: RD-0050 FCC id: PY7-RD0050 IC id: 4170B-RD0050 1(4) Revision 6 Specification Core Unit Marking Contents 1 2 2.1 2.2 3 Printing information............................................................................ 2 Contents and positioning of lazer etch printing .................................. 2 Contents ............................................................................................ 2 Positioning of printing ........................................................................ 4 REVISION INFORMATION ............................................................... 4 Abstract This document describes the label printing for SW2 (SmartWatch 2) 1271-4651 Company Internal Specification Document number 1275-3715 2(4) Revision 6 1 Printing information The printing is lazer etched in a grey color. The printing shall be sharp and well readable and shall withstand wearing. Material can be found in SPACE under 1271-4651 Contents and positioning of lazer etch printing The label shall have the following content, Position and alignment may vary:

2 2.1 Contents RTL type Position Text Icon middle Text middle Model: SW2 Text middle 1271-4651.1 Text middle Type number: RD-0050 Text middle FCC ID: PY7-RD0050 Text middle IC: 4170B-RD0050 Icon middle Text middle Made in Malaysia Text middle yyWww Note Align SONY-icon height:1.5mm Isolation zone:

1.5mm height:1.0mm height:1.0mm height:1.0mm height:1.0mm height:1.0mm NFC icon height: 3.0mm Isolation zone:

1.5mm height:1.0mm height:1.0mm Text middle BDA: XXXXXXXXXXXX actual unique BT address Text middle S/N: YYWWSSPCXXXXXXC Icon middle Icon middle yy = production year ww = production week height:1.0mm height:1.0mm Note 1 height:1.0mm width:9.5 mm

, height:3.0mm Japanese Lithium Ion battery statement Size: 1.0x9.5mm Japanese TA number and logo Symbol size: 3mm, text 1mm height Company Internal Specification Document number 1275-3715 3(4) Revision 6 Icon middle Icon left N12878 Icon left Z354 con right height: 5.0mm C-tick height:

3.0mm Text height:1.0mm mm height:0.9 width:3.1 height:5.0 width:4.5 CE-mark, symbol height 5.0mm C-tick icon with N12878 number Australian EMC requirement. Ref. doc C-tick mark height 3.0mm and text height 1.0mm 1001-5788 New Zealand EMC-requirement. Shall be put together with C-tick Recycling WEEE icon ref.doc. Min size: 5mm height of cross 1003-0743 Note1:

Serial No according to 4/159 35-LXE 108 179 YYWWSSPCXXXXXXC YY = Year WW = Week of production SS = Supplier/site PC = Production Line/Product Code XXXXXX = Serial value C = Checksum (in two positions) Company Internal Specification Document number 1275-3715 4(4) Revision 6 2.2 Positioning of printing The logotype, text and safety approval symbols mentioned under content shall be placed according to the following schematic sketch (only layout, no measurements). REVISION INFORMATION Version Date Note 2013 July, 88h 2013 July, 9th 2013 July, 11th 2013 Development revisions New release Complete re-make including size and position Added NFC icon and adjusted height of some icons 3 1-3 4 5 6

Confidentiality Request 2013-07-16 CGQBA13_334 Rev.A SOMC/CGQBADL/Fredrik3 Svensson +46 10 80 17253 Receiver Federal Communications Commission Request for Confidentiality FCC ID: PY7-RD0050 Block Diagram Schematic Diagram Part List Operational/Technical Descriptions Subject:

To Whom It May Concern:

In accordance with 0.459 of CFR 47, Sony Mobile Communications AB requests confidentiality for the below listed items for our Bluetooth Watch type: RD-0050, FCC ID: PY7-RD0050. 1. 2. 3. 4. These items contain detailed system and equipment description and related information about the product which Sony Mobile Communications AB considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sony Mobile Communications AB also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Please contact the undersigned if there are any further questions or additional information needed in this matter. Best Regards, ______________________ Fredrik Svensson Senior Verification Engineer Sony Mobile Communications AB