FCC ID: RYK-WPEQ276AX 802.11 ax Mini PCIe Module

Specification Standards Chipset Data Rate WPEQ-276AX Manual IEEE 802.11ax 2T2R 6G Qualcomm Atheros QCN9072 802.11ax: HE0~11 IEEE 802.11ax Operating Frequency 5.925~7.125GHz Interface Form Factor Antenna

*Subject to local regulations WLAN: PCIe Mini PCIe 2 x IPEX MHF1 connectors Wi-Fi :

Modulation 802.11ax: OFDMA (BPSK, QPSK, DBPSK, DQPSK, 16-QAM, 64-QAM, 256-QAM, Power Consumption 1024-QAM, 4096-QAM ) TX mode: 1288mA(Max.) RX mode: 965mA(Max.) Operating Voltage DC 3.3V Operating Temperature Range

-20C ~ +70C Storage Temperature Range

-20C ~ +90C Humidity

(Non-Condensing) 5%~90% (Operating) 5%~90% (Storing) Dimension L x W x H (in mm) 50.80mm(0.15mm) x 29.85mm(0.15mm) x 9.30mm(0.3mm) Weight (g) Driver Support Security 14.82g Linux 64/128-bits WEP, WPA, WPA2,WPA3,802.1x Block diagram:

Installation Connect the Module to the PCIe slot of the computer. After the Wi-Fi Driver is installed , click the Network icon on the Windows, then search the network , Install Wi-Fi driver driver. and connect the Wireless Network you want. Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF exposure statements This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. CFR 47 SUBPART E (15.407) has been investigated. It is applicable to the modular transmitter. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. This radio transmitterRYK-WPEQ276AX has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. Antenna Type Brand Antenna Model Maximum Gain

(dBi) 6 GHz Dipole SparkLAN AD-506AX 4.98 dBi Dipole SparkLAN AD-501AX 5 dBi Dipole SparkLAN AD-509AX Dipole SparkLAN AD-507AX Dipole SparkLAN AD-508AX 5 dBi 4.94 dBi 4.94 dBi Remark Length of Antenna cable:150mmConnector type of Antenna cable: I-PEX/MHF4 to RP-

SMA(F) If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:RYK-WPEQ276AX Or Contains FCC ID:RYK-WPEQ276AX The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the users manual. The module is for indoor applications only. The module may not be used for the purposes of remote control of drones The antenna must be installed into the host device so that the end user does not have access to the antenna or its connector. Minimum antenna gain, including any cable losses, for the 6GHz bands must exceed 0dBi. Label Indoor Only Info & restrictions. FCC regulations restrict the operation of this device to indoor use only. Operation prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. OEM Integrator must refer to FCC KDB 996369 D04 Module Integration Guide v02 for modular transmitter integration guidance. Industry Canada statement:

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration dexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This radio transmitter (IC: 6158A-WPEQ276AX has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 6158A-WPEQ276AX a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs cidessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antenna Type Brand Antenna Model Maximum Gain

(dBi) 6 GHz Dipole SparkLAN AD-506AX 4.98 dBi Dipole SparkLAN AD-501AX 5 dBi Dipole SparkLAN AD-509AX Dipole SparkLAN AD-507AX Dipole SparkLAN AD-508AX 5 dBi 4.94 dBi 4.94 dBi Remark Length of Antenna cable:150mmConnector type of Antenna cable: I-PEX/MHF4 to RP-

SMA(F) If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 6158A-WPEQ276AX. Si le numro de certification ISDE n'est pas visible lorsque le module est install l'intrieur d'un autre appareil, alors l'extrieur de l'appareil dans lequel le module est install doit galement afficher une tiquette faisant rfrence au module inclus. Cette tiquette extrieure peut utiliser un libell comme celui- ci:

Contient IC: 6158A-WPEQ276AX. Plaque signaltique du produit final:

Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC:

6158A-WPEQ276AX ". Manual Information To the End User:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manue Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: RYK-WPEQ276AX, Contains IC:6158A-

WPEQ276AX The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc / (metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID:RYK-WPEQ276AX, contient IC :

6158A-WPEQ276AX Operation shall be limited to indoor use only. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft. Le fonctionnement doit tre limit une utilisation en intrieur uniquement. L'exploitation sur les plates-formes ptrolires, les voitures, les trains, les bateaux et les aronefs est interdite, sauf pour les gros aronefs volant au-dessus de 10 000 pieds.

The dimensions of the module:

Label format and location:

The label shown is permanently affixed at a conspicuous location on the device with a permanent adhesive and be readily visible to the user at the time purchase (Labeling requirements per 2.925).

Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: 802.11 ax/ac/n Mini PCle Module / WPEQ-276AX 1. This device will only associate with a low power indoor AP for WIFI 6E operations. Hotspot Mode, ad-hoc and any other P2P service is disabled for WIFI 6E operations. This device will not connect directly to another client device using WIFI 6E frequencies. This device will always initiate transmission under the control of a low power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. The transmissions will be lower or equal to the power advertised by the indoor low-power access point and never above the maximum output power allowed by the FCC grant for equipment class 6XD. Contention-based protocol as demonstrated in the test report is permanently embedded in the module and is not host-dependent. This device is prohibited for control of or communications with unmanned aircraft systems, including drones. Not allowed on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. For modules this requirement is extended to Host Integrator through integration instructions. Device protocol attestation and contention-based protocol apply to functions permanently embedded in the module and cannot be host-dependent. Otherwise, the module must be restricted and filed as a Software Defined Radio or with joint responsibility agreements. Device Restriction statements: We, the grantee, will document the physical restrictions associated with the equipment classes for host products (wired power, integral antenna, non-

weatherized enclosure) as conditions-of-use through the host manufacture's integration instructions. Sincerely,. Grody dn Company Name: SparkLAN Communications, Inc. Contact Name: Grady Lin Tel: +886 2 2659 1880 Fax: +886 2 2659 5538 Email: grady.lin@sparklan.com Address: 5F, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan Data : 2022/9/26

SparkLAN Communications, Inc. SF, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan Date: 2022/09/05 FCC ID:RYK-WPEQ276AX Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize Underwriters Laboratories Taiwan Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Underwriters Laboratories Taiwan Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing Underwriters Laboratories Taiwan Co., Ltd. as our representative, we still recognize that we are responsible to:

a) b) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

Make claims regarding certification only in respect of the scope for which certification has been granted;

Do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

Upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

Use certification only to indicate the products are certified as being in conformity with specified standards;

g) h) a) k) Endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

Document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Gch) A: ae o\

Company Name: SparkLAN Communications, Inc. Contact Name: Grady Lin Tel: +886 2 2659 1880 Fax: +886 2 2659 5538 Email: grady.lin@sparklan.com Address: 5F, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan

SparkLAN Communications, Inc. SF, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan Date: Sep. 5, 2022 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Subject: Request for Confidentiality FCC ID:RYK-WPEQ276AX To whom it may concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Permanent Confidentiality Schematics Diagrams Block Diagram Operation Description Software Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. v1.0 se pe ee peng Short Term Confidentiality In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requests that the commission to grant short-term confidentiality request on the following attachments for 180day. e External Photo e Internal Photo e Test Setup Photo e User Manual It is our understanding that measurement test reports and FCC ID label format cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Orly A -

Name/Title: Grady Lin / R&D Manager Company Name: SparkLAN Communications, Inc. Address: SF, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan TEL: +886 2 2659 1880 FAX: +886 2 2659 5538 Email: grady.lin@sparklan.com v1.0

SparkLAN Communications, Inc. Date: 2022/09/05 FCC ID:RYK-WPEQ276AX To the certification reviewer:

We are hereby applying for full modular approval of the above-referenced FCC ID, based on compliance with all of the criteria as detailed below The requirements of Section 15.212 have been met and shown on the following statements Requirements EUT Conditions The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The radio portion of this module has been shielded, please see exhibition External. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The EUT has buffered data inputs, it is integrated in chip QCN9072 The modular transmitter must have its own power supply regulation.. The part number of this regulator is QCN9072 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph

(b) of this section. The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. Requirements EUT Conditions The modular transmitter must be tested in a stand-

alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another debice, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The EUT was tested in a stand-alone configuration via a PCIE extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition user manual, there are instructions give to the OEM on how to label the end product. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The EUT is compliant with all applicable FCC rules. Detail instructions for mainaining compliance are give in the user manual. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The EUT is compliant with all applicable RF exposure requirements. RF exposure is addressed in the RF exposure exhibition. Company Natne: SparkLAN Communications, Inc. Contact Name: Grady Lin Tel: +886 2 2659 1880 Fax: +886 2 2659 5538 Email: grady.lin@sparklan.com Address: SF, No. 199, Ruihu St., Neihu Dist., Taipei City 114067, Taiwan