WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5484969.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Wireless Module WPEA-252NIRB IEEE 802.11abgn (2T2R) Qualcomm Atheros QCA9592-AR1B 802.11b: 11Mbps / 802.11a/g: 54Mbps / 802.11n: 300Mbps IEEE 802.11 a/b/g/n ISM Band, 2.400GHz ~ 2.4835GHz, 5.150GHz ~ 5.825GHz
*Subject to local regulations Mini PCI Express Mini PCI-e 2 x HRS U.FL connectors for 2T2R 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11a/g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 3.3V 9% I/O supply voltage
-40C ~ +85C (Operating) / -50C ~ +90C (Storage) Operating Humidity (non-condensing): 10% ~ 85%
Storage Humidity (non-condensing): 5% ~ 90%
Continue TX: 700mA / Continue RX: 300mA 29.85 x 50.8 x 2.86 mm ( 0.5mm) 8g Linux 64/128-bits WEP, WPA, WPA2, 802.1x Specification Standards:
Chipset:
Data Rate:
Operating Frequency:
Interface:
Form Factor:
Antenna:
Modulation:
Operating Voltage:
Temperature Range:
Humidity
(Non-Condensing):
Power Consumption:
Dimension (in mm):
Weight (g):
Driver Support:
Security All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host which have similar RF exposure characteristic with equal or larger antenna separation distance. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling FOR MOBILE DEVICE USAGE (>20cm/low power) This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: RYK- WPEA252NIRB. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host which have similar RF exposure characteristic with equal or larger antenna separation distance. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre install et exploit avec plus de 20 cm entre l'antenne et les utilisateurs 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. 3) Approbation du Module valable que lorsque le module est install dans l'hte test ou de la srie de l'hte compatible qui ont mme caractristique de l'exposition aux RF avec la distance gale ou suprieure sparation antenne. Tant que les 3 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling FOR MOBILE DEVICE USAGE (>20cm/low power) This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 6158A-WPEA252NIRB. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 6158A-WPEA252NIRB". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(detachable antenna only)
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
(detachable antenna only)
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis pour les dispositifs utilisant les bandes de 5 250 5 350 MHz et de 5 470 5 725 MHz doit tre conforme la limite de la p.i.r.e; (detachable antenna only)
(iii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie, selon le cas;
(detachable antenna only)
(iv) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0 Wireless Module DETACHABLE ANTENNA USAGE This radio transmitter (IC: 6158A-WPEA252NIRB / Model: WPEA-252NIRB) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 6158A-WPEA252NIRB / Model: WPEA-252NIRB) a t approuv par ISED pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Approved antenna(s) list No. Transmitter Circuit Brand Model Antenna 2.4G gain with 5G gain with Type cable loss (dBi) cable loss (dBi) Connector Type 1 2 3 4 5 Chain(0) Chain(1) Chain(0) Chain(1) Chain(0) Chain(1) Chain(0) Chain(1) Chain(0) Chain(1) Sparklan AD-301N Dipole 4.4 Sparklan AD-103AG Dipole 2.02 Sparklan AD-305N Dipole 5.0 Sparklan AD-303N Dipole 3.0 Sparklan AD-302N Dipole 3.0 B1&2: 5.2 B3&4: 5.8 B1&2: 1.93 B3&4: 2.03 5.0 3.0 2.0 6 Chain(0) Chain(1) Taoglas Ma230.LBC
.002 PIFA 1.5 2.0 HRS U.FL at modular side & RP-SMA (M) at antenna side 1. 3M RG-174 with SMA(M) 2.3M CFD-200 with SMA(M) 3. 3M FD-200 with RP-SMA(M) All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFB-263ACNI(BT) ver.1.0