PRODUCT SPECIFICATION Standard Chipset Radio stream [Note1]
Antenna Type / con. Bus Interface Form Factor Data Rate Media Access Control Spreading /Modulation Techniques Frequency Range [Note2]
Transmit Output Power
(Tolerance: +/-2dBm) Receiver Sensitivity
(Tolerance: +/-2dBm) Operating Voltage Power Consumption Temperature Range WPEA-127NI IEEE802.11 abgn Atheros AR9390-AL1B 3T3R 3 U.FL connectors (diversity ant) PCI Express Mini PCIe 802.11b: 11, 5.5,2,1Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 23 for HT20MHz MCS 0 to 23 for HT40MHz CSMA/CA with ACK 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM) 802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM) 2.4GHz 11b/g/n: 2.400 ~ 2.4835GHz 5GHz 11a/n: 5.150GHz ~ 5.825GHz 802.11a: 11dBm 2dBm@54Mbps 802.11b: 19dBm 2dBm@11Mbps 802.11g: 16dBm 2dBm@54Mbps 802.11gn HT20: 15dBm 2dBm@MCS7 802.11gn HT40: 15dBm 2dBm@MCS7 802.11an HT20: 11dBm 2dBm@MCS7 802.11an HT40: 11dBm 2dBm@MCS7 802.11a: -78dBm 2dBm@54Mbps 802.11b: -95dBm 2dBm@11Mbps 802.11g: -79dBm 2dBm@54Mbps 802.11gn HT20: -76dBm 2dBm@MCS7 802.11gn HT40: -74dBm 2dBm@MCS7 802.11an HT20: -75dBm 2dBm@MCS7 802.11an HT40: -72dBm 2dBm@MCS7 3.3V 10% I/O supply voltage TX Mode: 970mA RX Mode: 300mA Associated Idle: 50 mA
-40~+80C (Operating) [Note3]
Humidity (non-condensing) Security OS supported Note:
1. For Radio stream with diversity or MIMO design, all RF connectors on the module must be fitting 20~80%(Operating), 5~95%(Storing) [Note3]
WEP / WPA / WPA2 Windows XP/Vista/Win7, Linux antennas in order to guarantee the module performance. 2. The frequency range need to local regulations. 3. The storing condition is only for product functionality, no included for parts appearance. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: RYK-WPEA127NI. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:6158A-WPEA127NI. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC:
6158A-WPEA127NI". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;
(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. This device has been designed to operate with an antenna having a maximum gain of 5 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (IC: 6158A-WPEA127NI / Model: WPEA-127NI) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Ce dispositif a t conu pour fonctionner avec une antenne ayant un gain maximal de 5 dBi. Une antenne gain plus lev est strictement interdite par les rglements d'Industrie Canada. L'impdance d'antenne requise est de 50 ohms. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pourl'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent metteur radio (IC: 6158A-WPEA127NI / Modle: WPEA-127NI) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Approved antenna(s) list Type The cavity-backed slot antenna Gain For 5G: 4.58 dBi