WPEQ-256ACNRBI WPEQ-256ACN 1 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
Product Introduction Standard Chipset solution Radio stream [Note1]
Antenna type / connector. Bus Interface Form Factor IEEE802.11ac/a/b/g/n QCA9892-BR4B 2T2R External with IPEX connector PCI Express Mini-PCIe 802.11b: 11, 5.5, 2, 1 Mbps;
802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n:
MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz 802.11ac:
MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz 1. In HT (High Throughput) mode, the data rate depends on the MCS Index. 2. The MCS index for HT (High Throughput) mode is from 0 to 32 as described in the MCS table. 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM) 802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM) 802.11ac: OFDM (BPSK,QPSK,16-QAM,64-QAM, 256-QAM) Data Rate Spreading /Modulation Techniques Frequency Range
[Note2]
11b/g/n: 2.412GHz ~ 2.484GHz 11ac/a/n: 5.15GHz ~ 5.85GHz 2 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
Transmit Output Power
(Tolerance: +/-2dBm) Receiver Sensitivity 802.11a: 14dBm@54Mbps 802.11b: 20dBm@11Mbps 802.11g: 16dBm@54Mbps 802.11gn HT20: 15dBm@MCS7 802.11gn HT40: 15dBm@MCS7 802.11an HT20: 13dBm@MCS7 802.11an HT40: 13dBm@MCS7 802.11ac VHT80: 10dBm@MCS9 802.11a: -74dBm@54Mbps 802.11b: -87dBm@11Mbps 802.11g: -74dBm@54Mbps 802.11gn HT20: -70dBm@MCS7 802.11gn HT40: -68dBm@MCS7 802.11an HT20: -71dBm@MCS7 802.11an HT40: -68dBm@MCS7 802.11ac VHT80: -59dBm@MCS9 Operating Voltage DC 3.3V Power Consumption TX Mode:1050mA (Max.) Temperature Range Humidity (non-condensing) Security OS supported
-40C~+85C (Operating), -40C~+85C (storing) 10~85 % (Operating), 5~90 % (Storing) [Note3]
WEP / WPA / WPA2,802.1X Linux (Linux supports have different versions based on different CPU platforms and O/S. Please contact SPK support group.) Note:
1. For Radio stream with diversity or MIMO design, all RF connectors on the module must be fitting antennas in order to guarantee the module performance. 2. The frequency range is subject to local regulations. 3. The storing condition is only for product functionality, no included for parts appearance. 3 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
2. Hardware Specification 2.1 Hardware Dimension Dimension: 50.8mm * 29.85mm * 4.1mm(0.5mm) 4 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
2.3 Pin Assignment The following section illustrate signal pin-outs for the system connector. Pin#
Pin Name Description Pin#
Pin Name Description Output and open Drain active Low signal. This signal is used to request that the system return from a sleep/suspended state to service a function initiated wake event.
-
-
Output for reference clock request signal 2
+3.3V 4 6 8 GND No Connection No Connection 1 WAKE_L(NA) No Connection No Connection CLKREQ_L 3 5 7 9 GND GND 10 No Connection 11 REFCLK-
13 REFCLK+
Input signal for PCI Express differential reference clock (100 MHz) Input signal for PCI Express differential reference clock (100 MHz) 15 17 GND GND No Connection 19 No Connection
-
-
12 No Connection 14 No Connection 16 18 No Connection GND 20 W_DISABLE_L
(OPT) 5
+3.3V GND
-
-
-
-
-
-
GND Input and active low signal. This signal is used by the system to disable radio operation on add-in cards that implement radio frequency applications. When implemented, PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
21 GND GND 22 PERST_L 23 PERn0 25 PERp0 27 29 GND GND 31 PETn0 33 PETp0 PCI Express x1 data interface: one differential receive pair PCI Express x1 data interface: one differential receive pair 24
+3.3V 26 GND GND GND 28 30 No Connection No Connection PCI Express x1 data interface: one differential transmit pair PCI Express x1 data interface: one differential transmit pair 32 No Connection 34 GND 36 38 40 42 No Connection No Connection GND No Connection 35 37 39 41 GND GND No Connection No Connection GND GND
-
-
43 GND GND 44 LED_WLAN_L
(OPT) 45 47 49 51 No Connection No Connection No Connection No Connection
-
-
-
-
No Connection No Connection GND
+3.3V 46 48 50 52 6 this signal requires a pull-up resistor on the card Input signal for functional reset to the card
+3.3V GND
-
-
-
GND
-
-
GND
-
Output and open drain active low signal. This signal is used to allow the PCI Express Mini Card add-in card to provide status indicators via LED devices that will be provided by the system
-
-
GND
+3.3V PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
* NA: No active
* OPT: Optional (Depends on S/W and H/W design of the module and customer platform main board, functionalities of end devices and drivers.) 7 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This device is restricted to indoor use. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The module is limited to OEM installation ONLY. This module is intended for OEM integrators under the following conditions:
1. This module is restricted to installation in products for use only in mobile and fixed applications. 2. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. 3. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. 4. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. 5. Fixed outdoor applications for point to multipoint operations are subject to the conditions in Part 8 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
15.407(a)(1)(i). The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations
(e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations The user manual of the end product should include 1. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. the restriction of operating this device in indoor could void the users authority to operate the equipment. 2. 3. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 4. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. 5. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label of the end product:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
RYK-WPEQ256ACN". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 9 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This radio transmitter [IC: 6158A-WPEQ256ACN] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. FCC/ISED Antenna List
#
1 2 3 4 5 6 Brand Model Connector Type Type SparkLAN SparkLAN SparkLAN SparkLAN SparkLAN SparkLAN AD-103AG AD-301N AD-302N AD-303N AD-305N AD-300N I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex Dipole Dipole Dipole Dipole Dipole Dipole 5GHz Band 1 Band 2 Band 3 Band 4 5.8 5.2 2.03 2.87 3.45 5.53 5 2.4GHz 2.02 4.4 3.14 3.14 5 3 Le prsent metteur radio [IC: 6158A-WPEQ256ACN] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. FCC/ISED Antenna List
#
1 2 3 4 5 6 Brand Model Connector Type Type 5GHz Band 1 Band 2 Band 3 Band 4 SparkLAN SparkLAN SparkLAN SparkLAN SparkLAN SparkLAN AD-103AG AD-301N AD-302N AD-303N AD-305N AD-300N I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex 5.8 5.2 2.03 2.87 3.45 5.53 5 Dipole Dipole Dipole Dipole Dipole Dipole 10 2.4GHz 2.02 4.4 3.14 3.14 5 3 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps Modular OEM Integrator Notice This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the ISED compliance requirement of the end product, which integrates this module. 3. Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations and different antenna configurations End Product Labeling The final end product must be labeled in a visible area with the following: Contains transmitter module IC:
6158A-WPEQ256ACN. Contient le module d'mission IC: IC: 6158A-WPEQ256ACN 11 PRODUCT APPROVAL SHEET WPEQ-256ACNRBI [W]
The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. Japan Antenna List
#
Brand Model vso GRF1351 RFDPA131000SBLB808 ALX17P-221XX9-00 ALX17P-221XXG-00 RFA-25-C17M5-1 AN2450-5511BRS ANTDP-027A0 MA231.LBC.002 GPOT113-020A 1 Walsin 2 Cortec SANSEI 3 4 Taoglas 5 WIESON 6 AN2450-16HM01BRS Cortec 7 ARISTOTLE RFA-25-AP252-70-500 8 ARISTOTLE RFA-25-AP287-4B-350F 9 LYNwave 10 LYNwave 11 ARISTOTLE 12 13 14 15 16 EX06-2458-B1-SMA-MR 17 ARISTOTLE RFA-25-C2M2-U-M70 18 ARISTOTLE RFA-25-C2M2-M32-N 19 SparkLAN 20 SparkLAN 21 SparkLAN 22 SparkLAN 23 SparkLAN 24 SparkLAN 25 SparkLAN AD-103AG AD-301N AD-302N AD-303N AD-305N AD-300N AD-300PF C0255-ANG0027 C0255-ANG0029 C0255-ANG0018 exceltek exceltek exceltek Anjie Connector Type I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex I-Pex Type Dipole Dipole Dipole Flat Bar Dipole Dipole PCB PCB PCB PCB Dipole Dipole PCB PCB Dipole Dipole Dipole Dipole Dipole Dipole Dipole Dipole Dipole Dipole Pifa Band 1 5GHz Band 2 4.4 3.14 1.3 2.84
-5.96 1.3 2.84
-5.96 3.5 3.6 3.6 2 2 2.8 2.34 6.27 2.6 4.8 5.2 3.5 3.6 3.6 3 2 2 2.6 1.9 2.34 1.81 2.03 2.87 3.45 5.53 5 5 2.4GHz Band 3 3.58 1.2 2.84
-5.96 6.67 3.62 3.5 3.6 3.6 4.9 2 2 2.9 2.34 5.8 2.93 2.89 1.5 2.41
-0.79 2.15 2.47 2.8 3.7 3.7 1.5 2.9 2 2 2.4 1.5 2.9 2.56 2.02 4.4 3.14 3.14 5 3 3 12