WNFQ-258ACN(BT) Standard IEEE802.11ac/a/b/g/n, Bluetooth V4.1,V4.0 LE, V3.0+HS, V2.1+EDR Chipset solution QCA6174A-5 Radio stream [Note1]
2T2R (Support WiFi/BT co-existence) Antenna Type / con. IPEX MHF4 connector Bus Interface Form Factor Data Rate WiFi: PCI Express BT: USB M.2 2230 WiFi:
802.11b: 11, 5.5, 2, 1 Mbps;
802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz 802.11ac: MCS 0 to 9 for VHT20MHz MCS 0 to 9 for VHT40MHz MCS 0 to 9 for VHT80MHz BT:
1 Mbps, 2Mbps and Up to 3Mbps EDR WiFi:
802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM) Spreading /Modulation 802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM) Techniques 802.11ac: OFDM (BPSK,QPSK,16-QAM,64-QAM, 256-QAM) BT:
Header: GFSK Payload 2M: 4-DQPSK Payload 3M: 8-DPSK WiFi:
11b/g/n: 2.412GHz ~ 2.484GHz 11ac/a/n: 5.15GHz ~ 5.85GHz BT:
2.402GHz ~ 2.480 GHz WiFi:
802.11a: 11dBm@54Mbps 802.11b: 19dBm@11Mbps 802.11g: 16dBm@54Mbps 5180 802.11gn HT20: 16dBm@MCS7 Frequency Range [Note2]
Transmit Output Power
(Tolerance: +/-2dBm) 802.11gn HT40: 15dBm@MCS7 802.11an HT20: 9dBm@MCS7 802.11an HT40: 9dBm@MCS7 802.11ac VHT80: 7dBm@MCS9 BT: (Class 2 Device) 0 Output Power +4 dBm WiFi:
802.11b: -81dBm@11Mbps 802.11g: -66dBm@54Mbps 802.11a: -66dBm@54Mbps Receiver Sensitivity 802.11gn HT40: -61dBm@MCS7 802.11gn HT20: -65dBm@MCS7 802.11an HT20: -65dBm@MCS7 802.11an HT40: -61dBm@MCS7 802.11ac VHT80: -56dBm@MCS9 BT:
< 0.1% BER at -70dBm Operating Voltage DC 3.3V Power Consumption TX Mode: 405 mA RX Mode: 200 mA Temperature Range
-10~+70C (Operating), -40~+85C (Storing) [Note3]
Humidity (non-condensing) 5~90%(Operating), 5~90 % (Storing) [Note3]
Security OS supported WEP / WPA / WPA2,802.1X Win7/Win8.1/Win10 Note:
1. For Radio stream with diversity or MIMO design, all RF connectors on the module must be fitting antennas in order to guarantee the module performance. 2. The frequency range is subject to local regulations. 3. The storing condition is only for product functionality, no included for parts appearance. NCC
(1)
-
-
(2)
(3)
(1)
(2)
(3) FCC Label Compliance Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
(4)
(5)
(6) End Product Labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: RYK-WNFQ258ACNBT . The grantee's FCC ID can be used only when all FCC compliance requirements are met. Radiation Exposure Statement This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Radiation Exposure Statement:
1) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. 2) The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
(7)
(8)
(1)
(1) End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: RYK-WNFQ258ACNBT. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual IC Compliance Statement:
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions :
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet appareil radio est conforme au CNR-247 dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
(2)
(2)
(3) Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
(iii) pour les dispositifs dots d'antenne (s) dtachable (s), le gain maximal d'antenne autoris pour les appareils de la bande 5725-5850 MHz doit tre tel que l'quipement soit toujours conforme aux normes e.i.r.p. Limites spcifies pour les oprations point point et non point--point selon le cas This radio transmitter (IC:6158A-258ACNBT) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Name Antenna Type Wanshin R3410110203 GEC6200 Dipole Dipole Peak Gain(dBi) 2.4G 2 dbi 3 dbi 5G 2dbi 5 dbi
(3)
(4)
(4)
(5)
(5) Le prsent metteur radio (IC: 6158A-258ACNBT) at approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Compliance with IC requirement RSS-247 data transmission is always initiated by software, which is then passed down through the MAC, through the digital and analog baseband, and finally to the RF transceiver. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted. est conforme au CNR-247 la transmission de donnes est toujours initie par le logiciel, qui est ensuite transmis travers la MAC, travers la bande de base numrique et analogique et, enfin, l'metteur-rcepteur RF. Plusieurs paquets spciaux sont inities par le MAC. Ce sont les seuls moyens de la partie bande de base numrique se met en marche l'metteur RF, ce qui lui puis s'teint la fin du paquet. Par consquent, l'metteur sera sur que lorsque l'un des paquets ci-dessus sont transmises. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrl. L'antenne doit tre install de faon garder une distance minimale de 20 centimtres entre la source de rayonnements et votre corps. L'metteur ne doit pas tre colocalis ni fonctionner conjointement avec autre antenne ou autre metteur.
(1)
(1)
(2)
(2)
(3) This device is intended only for OEM integrators under the following conditions:
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
(2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
(1)L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et
(2)Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. End Product Labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:6158A-258ACNBT. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:
"Contient des IC:6158A-258ACNBT ". Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final:
L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel.
(3)