FCC ID: RYK-WNFQ268AXBT Wi-Fi 6E BT M.2 Module

Wireless Module WNFQ-268AXI(BT) WNFQ-268AX(BT) Specification Standards Chipset Data Rate Operating Frequency Interface IEEE 802.11ax/ac/a/b/g/n (2T2R) Bluetooth V5.2, V5.1, V5.0, V4.2, V4.1, V4.0LE, V3.0, V2.1+EDR Qualcomm Atheros WCN6856 802.11b: 11Mbps 802.11a/g: 54Mbps 802.11n: MCS0~15 802.11ac: MCS0~9 802.11ax: HE0~11 Bluetooth: 1 Mbps, 2Mbps and Up to 3Mbps IEEE 802.11ax/ac/a/b/g/n ISM Band, 2.412GHz~2.484GHz, 5.150GHz~5.850GHz ,5.925~7.125GHz(FCC only)

*Subject to local regulations WLAN: PCIe Bluetooth: USB Form Factor M.2 2230 E Key and AE key Antenna 2 x IPEX MHF4 connectors Ant 1 for WLAN/BT, Ant 2 for WLAN Wi-Fi:

802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) Modulation 802.11ac: OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM) 802.11ax: OFDMA (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM) BT:

Header: GFSK Payload 2M: /4-DQPSK Payload 3M: 8-DPSK All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 Wireless Module Operating Voltage DC 3.3V Operating Temperature Range WNFQ-268AXI(BT) Operating Temp: -40C ~75C;

WNFQ-268AX(BT) Operating Temp: -10C ~65C Storage Temperature Range

-45C~90C Humidity 5%~90% (Operating)

(Non-Condensing) 5%~90% (Storing) Dimension L x W x H (in mm) 30mm( 0.15mm) x 22mm( 0.15mm) x 3.5mm( 0.3mm) Weight (g) Security 3.2g 64/128-bits WEP, WPA, WPA2, WPA3, 802.1x All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 Block Diagram Wireless Module Mechanical Dimension (mm) All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 Wireless Module Pin Assignment (TBD) The following section illustrate signal pin-outs for the module connector. Pin#

Pin Name 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 GND USB_D+

USB_D-

GND SDIO_CLK/SYSCLK SDIO_CMD SDIO_DATA0 SDIO_DATA1 SDIO_DATA2 SDIO_DATA3 SDIO_WAKE#

SDIO_RESET#/TX_BLANKING NOTCH FOR KEY E NOTCH FOR KEY E NOTCH FOR KEY E NOTCH FOR KEY E GND PERp0 PERn0 GND PETp0 PETn0 GND REFCLKp0 REFCLKn0 GND CLKREQ0# (3.3V) PEWAKE0# (3.3V) GND RESERVED/PERp1 TOP Type G Ground connections Description I/O I/O G NC NC NC NC NC NC NC NC NC NC NC NC G I I G O O G I I USB serial differential data Positive USB serial differential data Negative Ground connections No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection Ground connections PCI Express receive data-Positive PCI Express receive data-Negative Ground connections PCI Express transmit data- Positive PCI Express transmit data- Negative Ground connections PCI Express differential clock input- Positive PCI Express differential clock input- Negative G Ground connections OD OD PCIe clock request PCIe wake signal G Ground connections NC No Connection All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 Wireless Module 61 63 65 67 69 71 73 75 RESERVED/PERn1 GND RESERVED/PETp1 RESERVED/PETn1 GND RESERVED/REFCLKp1 RESERVED/REFCLKn1 GND Pin Assignment NC No Connection G NC NC G NC NC G Ground connections No Connection No Connection Ground connections No Connection No Connection Ground connections Pin#

Pin Name BOTTOM Type Description 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 3.3 V 3.3 V LED_1#

PCM_CLK/I2S_SCK (1.8V) PCM_SYNC/I2S_WS (1.8V) PCM_OUT/I2S_SD_OUT (1.8V) PCM_IN/I2S_SD_IN (1.8V) LED_2#

GND UART_WAKE# (3.3V) UART_TXD NOTCH FOR KEY E NOTCH FOR KEY E NOTCH FOR KEY E NOTCH FOR KEY E UART_RXD UART_RTS UART_CTS VENDOR DEFINED VENDOR DEFINED VENDOR DEFINED COEX3 COEX_TXD COEX_RXD P P O I I O I O G NC NC NC NC NC NC NC NC NC NC NC NC NC VDD system power supply input VDD system power supply input WLAN LED I2S Continuous Serial Clock (SCK). I2S Word Select. I2S Serial Data IN. I2S Serial Data OUT. Bluetooth LED Ground connections No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection DNC Do Not Connect DNC Do Not Connect All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 50 52 SUSCLK PERST0#

54 W_DISABLE2#

56 W_DISABLE1#

58 60 62 64 66 68 70 72 74 I2C_DATA I2C_CLK ALERT#

RESERVED UIM_SWP/PERST1#

UIM_POWER_SNK/CLKREQ1#

UIM_POWER_SRC/GPIO_1/PEWAKE1#

3.3 V 3.3 V Wireless Module NC No Connection I I I NC NC NC NC NC NC NC P P PCIe host indication to reset the device Active low. BT enable signal. WLAN enable signal. No Connection No Connection No Connection No Connection No Connection No Connection No Connection VDD system power supply input VDD system power supply input Note: Power (P), Ground (G), Open-Drain (OD), Input (I), Output (O), Do Not Connect (DNC), No Connection (NC) All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880 WNFQ-268AXI(BT) ver.0.93 Installation Connect the Module to the PCIe slot of the computer. After the Wi-Fi Driver is installed , click the Network icon on the Windows, then Install Wi-Fi driver driver. search the network , and connect the Wireless Network you want. Federal Communication Commission Interference Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF exposure statements This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. CFR 47 FCC PART 15 SUBPART C (15.247) and SUBPART E (15.407) has been investigated. It is applicable to the modular transmitter. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. This radio transmitterRYK-WNFQ268AXBT has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. Antenna Type Brand Antenna Model Maximum Gain (dBi) 2.4 GHz 5GHz 6GHz Remark Length of Antenna Dipole SparkLAN AD-500AX 2.65 dBi 4.81 dBi 4.98 dBi cable:550mm Connector type of Dipole SparkLAN AD-501AX 3.7 dBi 5 dBi 5 dBi Antenna cable: I-PEX/MHF4 Length of Antenna cable:150mm Connector type of Antenna cable: I-PEX/MHF4 to RP-SMA Length of Antenna PIFA SparkLAN AD-502AX 3.5 dBi 5 dBi 3.9 dBi cable:300mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna Dipole SparkLAN AD-503AX 3.7 dBi 5 dBi 5 dBi cable:150mm Connector type of Antenna cable: I-PEX/MHF4 CHIP SparkLAN 2450AD18A6050 2 dBi 1.5 dBi 2.7 dBi N/A Dipole SparkLAN Length of Antenna AD-504AX 2.67dBi 4.87 dBi 4.94 dBi cable:150mm Connector type of Dipole SparkLAN Antenna cable: I-PEX/MHF4 Length of Antenna AD-505AX 2.67dBi 4.87 dBi 4.94 dBi cable:250mm Connector type of Antenna cable: I-PEX/MHF4 If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:RYK-

WNFQ268AXBT Or Contains FCC ID:RYK-WNFQ268AXBT The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the users manual. The module is for indoor applications only. The module may not be used for the purposes of remote control of drones The antenna must be installed into the host device so that the end user does not have access to the antenna or its connector. Minimum antenna gain, including any cable losses, for the 6GHz bands must exceed 0dBi. Industry Canada statement:

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Caution:

1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and Avertissement:

1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

2) Le gain maximal dantenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer la imitation P.I.R.E.;

3) Le gain maximal dantenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer la limitation P.I.R.E spcifie pour lexploitation point point et non point point, selon le cas. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration dexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This radio transmitter (IC: 6158A-WNFQ268AXBT has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 6158A-WNFQ268AXBT a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs cidessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Antenna Type Brand Antenna Model Maximum Gain (dBi) 2.4 GHz 5GHz Remark Dipole SparkLAN AD-500AX 2.65 dBi 4.81 dBi Length of Antenna cable:550mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:150mm Dipole SparkLAN AD-501AX 3.7 dBi 5 dBi Connector type of Antenna Dipole SparkLAN AD-310N 2.65 dBi 4.86 dBi PIFA SparkLAN AD-502AX 3.5 dBi 5 dBi Dipole SparkLAN AD-503AX 3.7 dBi 5 dBi cable: I-PEX/MHF4 to RP-

SMA Length of Antenna cable:550mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:300mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:150mm Connector type of Antenna cable: I-PEX/MHF4 CHIP SparkLAN 2450AD18A6050 2 dBi 1.5 dBi N/A Length of Antenna cable:150mm Dipole SparkLAN AD103AG 2.02 dBi 2.03 dBi Connector type of Antenna cable: I-PEX/MHF4 to RP-

SMA Dipole SparkLAN AD-302N 3.14 dBi 2.74 dBi Connector type of Antenna Length of Antenna cable:150mm Dipole SparkLAN AD-303N 3.14 dBi 3.24 dBi Connector type of Antenna cable: I-PEX/MHF4 to RP-

SMA Length of Antenna cable:150mm Dipole SparkLAN AD-308N 3 dBi 5 dBi Dipole SparkLAN AD-504AX 2.67 dBi 4.87 dBi Dipole SparkLAN AD-505AX 2.67 dBi 4.87 dBi cable: I-PEX/MHF4 to RP-

SMA Length of Antenna cable:150mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:150mm Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:250mm Connector type of Antenna cable: I-PEX/MHF4 If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 6158A-WNFQ268AXBT. Si le numro de certification ISDE n'est pas visible lorsque le module est install l'intrieur d'un autre appareil, alors l'extrieur de l'appareil dans lequel le module est install doit galement afficher une tiquette faisant rfrence au module inclus. Cette tiquette extrieure peut utiliser un libell comme celui-ci: Contient IC:

6158A-WNFQ268AXBT. Plaque signaltique du produit final:

Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:

"Contient des IC: 6158A-WNFQ268AXBT ". Manual Information To the End User:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manue Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: RYK-WNFQ268AXBT, Contains IC:6158A-WNFQ268AXBT The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc / (metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID:RYK-

WNFQ268AXBT, contient IC : 6158A-WNFQ268AXBT

Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Product/ Model Number: Wi-Fi 6E BT M.2 Module/ WNFQ-268AXI(BT) 1. This device will only associate with a low power indoor AP for WIFI 6E operations. Hotspot Mode, ad-hoc and any other P2P service is disabled for WIFI 6E operations. This device will not connect directly to another client device using WIFI 6E frequencies. 2. This device will always initiate transmission under the control of a low power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. 3. The transmissions will be lower or equal to the power advertised by the indoor low-power access point and never above the maximum output power allowed by the FCC grant for equipment class 6XD. 4. Contention-based protocol as demonstrated in the test report is permanently embedded in the module and is not host-dependent. 5. This device is prohibited for control of or communications with unmanned aircraft systems, including drones. 6. Device protocol attestation and contention-based protocol apply to functions permanently embedded in the module and cannot be host-dependent. Otherwise, the module must be restricted and filed as a Software Defined Radio or with joint responsibility agreements. 7. Device Restriction statements: We, the grantee, will document the physical restrictions associated with the equipment classes for host products (wired power, integral antenna, non-weatherized enclosure) as conditions-of-use through the host manufacture's integration instructions. Sincerely,. seedy A Company Name: SparkLAN Communications, Inc. Contact Name: Grady Lin Tel: +886 2 2659 1880 Fax: +886 2 2659 5538 Email: grady.lin@sparklan.com Address: 8F., No.257, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.) Data : 2022/1/17