all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User manual | Users Manual | 386.79 KiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | Cover Letter(s) | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User manual | Users Manual | 386.79 KiB |
Users Manual Version: 1.0 Wireless 802.11g Multi-mode AP WAPR-141 Trademarks Copyright @2005 Contents are subject to change without notice. All trademarks belong to their respective proprietors. Copyright Statement THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF THIS COMPANY. AND NO PART OF THIS DOCUMENTATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRICAL OR MECHANICAL, BY PHOTOCOPYING, RECORDING, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN CONSENT OF THIS COMPANY. INFORMATION TO USER Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help. Installation and use of this Wireless 802.11g Multi-mode AP device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency (RF) signal. In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. SparkLAN declares that US model of WAPR-141, ( FCC ID: RYK-WAPR141) is limited in CH 1 ~ CH 11 for 2.4 G band by specific firmware controlled by the manufacturer and is not user changeable. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. REGULATORY INFORMATION Wireless 802.11g Multi-mode AP must be installed and used in strict accordance with the instructions. This device complies with the following radio frequency and safety standards. USA - Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference that may cause undesired operation. Europe- R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity
(R&TTE) CE Declaration of Conformity For the following equipment:
Wireless 802.11g Multi-mode AP
(Product Name) WAPR-141
(Model Designation) is herewith confirmed to comply with the requirements set out in the Council
(European parliament) Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device
(1999/5/EC). For the evaluation regarding this Directive, the following standards were applied:
EN 300 328 V1.6.1 (2004-11) EN 301 489-1 V1.5.1 (2004-11), EN 301 489-17 V1.2.1 (2002-08) EN 60950-1: 2001 EN 50385 EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Norway, and Switzerland. EU Countries Not intended for use None. Potential restrictive use France: Only channels 10,11,12, and 13 The channel identifiers, channel center frequencies, and regulatory domains of each 22-MHz-wide channel are shown in following Table. Channel Identifier 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Center Frequency
(MHZ) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2484 Regulatory Domains Japan ETSI North America Israel France Mexico USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Table of Contents REVISION HISTORY .....................................................................................................................I TERMINOLOGY ........................................................................................................................... II 1 INTRODUCTION.................................................................................................................... 1 1.1 PACKAGE CONTENTS ............................................................................................................ 1 1.2 PRODUCT SPECIFICATIONS ................................................................................................... 1 1.3 PRODUCT FEATURES ............................................................................................................ 2 1.4 UPPER PANEL DESCRIPTION ................................................................................................. 3 1.5 REAR PANEL DESCRIPTION................................................................................................... 4 2 INSTALLATION ..................................................................................................................... 5 2.1 HARDWARE INSTALLATION .................................................................................................. 5 SOFTWARE INSTALLATION.................................................................................................... 5 2.2 3 SOFTWARE CONFIGURATION ......................................................................................... 6 3.3.1 3.3.2 3.1 PREPARE YOUR PC TO CONFIGURE THE WIRELESS 802.11G MULTI-MODE AP...................... 6 3.2 CONNECT TO THE WIRELESS 802.11G MULTI-MODE AP....................................................... 8 3.3 MANAGEMENT AND CONFIGURATION ON THE WIRELESS 802.11G MULTI-MODE AP ............ 8 Status.......................................................................................................................... 8 Setup Wizard.............................................................................................................. 9 LAN Interface Setup.................................................................................................... 10 I II Wireless Basic Settings................................................................................................ 11 III Wireless Security Setup ........................................................................................... 12 3.3.3 Wireless - Basic Settings.......................................................................................... 12 3.3.4 Wireless - Advanced Settings .................................................................................. 14 3.3.5 Wireless - Security Setup......................................................................................... 15 I WEP Key Setup ........................................................................................................... 17 3.3.6 Wireless - Access Control........................................................................................ 18 3.3.7 WDS Settings........................................................................................................... 20 I WDS Security Setup .................................................................................................... 21 II WDS AP Table ............................................................................................................. 21 Site Survey............................................................................................................... 22 TCP/IP Settings........................................................................................................ 23 3.3.8 3.3.9 i USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Log ........................................................................................................................... 25 3.3.10 3.3.11 Statistics ................................................................................................................... 26 3.3.12 Upgrade Firmware ................................................................................................... 27 Save/ Reload Settings .............................................................................................. 27 3.3.13 3.3.14 Password Setup ........................................................................................................ 28 Logout...................................................................................................................... 29 3.3.15 4 FREQUENTLY ASKED QUESTIONS (FAQ).................................................................... 30 4.1 WHAT AND HOW TO FIND MY PCS IP AND MAC ADDRESS? .............................................. 30 4.2 WHAT IS WIRELESS LAN? ................................................................................................. 30 4.3 WHAT ARE ISM BANDS? .................................................................................................... 30 4.4 HOW DOES WIRELESS NETWORKING WORK?....................................................................... 30 4.5 WHAT IS BSSID? ............................................................................................................... 31 4.6 WHAT IS ESSID? ............................................................................................................... 31 4.7 WHAT ARE POTENTIAL FACTORS THAT MAY CAUSES INTERFERENCE? ................................. 32 4.8 WHAT ARE THE OPEN SYSTEM AND SHARED KEY AUTHENTICATIONS? .............................. 32 4.9 WHAT IS WEP? .................................................................................................................. 32 4.10 WHAT IS FRAGMENT THRESHOLD?..................................................................................... 32 4.11 WHAT IS RTS (REQUEST TO SEND) THRESHOLD?.............................................................. 33 4.12 WHAT IS BEACON INTERVAL?............................................................................................. 33 4.13 WHAT IS PREAMBLE TYPE?................................................................................................ 34 4.14 WHAT IS SSID BROADCAST? ............................................................................................. 34 4.15 WHAT IS WI-FI PROTECTED ACCESS (WPA)? .................................................................... 34 4.16 WHAT IS WPA2?................................................................................................................ 35 4.17 WHAT IS 802.1X AUTHENTICATION? .................................................................................. 35 4.18 WHAT IS TEMPORAL KEY INTEGRITY PROTOCOL (TKIP)? ................................................. 35 4.19 WHAT IS ADVANCED ENCRYPTION STANDARD (AES)? ...................................................... 35 4.20 WHAT IS INTER-ACCESS POINT PROTOCOL (IAPP)?........................................................... 35 4.21 WHAT IS WIRELESS DISTRIBUTION SYSTEM (WDS)?......................................................... 36 4.22 WHAT IS CLONE MAC ADDRESS?...................................................................................... 36 ii USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Revision History DATE 2006/5/19 REVISION OF USERS MANUAL First release (Version 1.0) FIRMWARE a1.4.0 i USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Terminology AES ANSI AP CCK CSMA/CA CSMA/CD DHCP DSSS EAP ESP FCC IEEE IP ISM LAN MAC NT PSD RF SNR SSID TCP TFTP TKIP WDS WEP WLAN WPA Advanced Encryption Standard American National Standards Institute Access Point Complementary Code Keying Carrier Sense Multiple Access/ Collision Avoidance Carrier Sense Multiple Access/ Collision Detection Dynamic Host Configuration Protocol Direct Sequence Spread Spectrum Extensible Authentication Protocol Encapsulating Security Payload Federal Communications Commission Institute of Electrical and Electronic Engineers Internet Protocol Industrial, Scientific and Medical Local Area Network Media Access Control Network Termination Power Spectral Density Radio Frequency Signal to Noise Ratio Service Set Identification Transmission Control Protocol Trivial File Transfer Protocol Temporal Key Integrity Protocol Wireless Distribution System Wired Equivalent Privacy Wireless Local Area Network Wi-Fi Protected Access ii USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 1 Introduction The Wireless 802.11g Multi-mode AP is an affordable IEEE 802.11b/g Wireless 802.11g Multi-mode AP solution; setting SOHO and enterprise standard for high performance, secure, manageable and reliable WLAN. This document describes the steps required for the initial IP address assign and other WLAN router configuration. The description includes the implementation of the above steps. 1.1 Package contents The package of the Wireless 802.11g Multi-mode AP includes the following items,
The Wireless 802.11g Multi-mode AP
The AC to DC power adapter
The Documentation CD
1.8M RJ-45 Cable Line 1.2 Product Specifications Wireless 802.11g Multi-mode AP 802.11b/g(Wireless), 802.3(10BaseT), 802.3u(100BaseT) 54Mbps(Wireless), 100Mbps(Ethernet) CCK(802.11b), OFDM(802.11g) 2.4GHz 2.4835GHz ISM Band, DSSS CCK< 18 dBm, OFDM< 15 dBm 802.11b -80 dBm@8%, 802.11g -68 dBm@5%
30 to 280 meters (depend on surrounding) External Antenna Power, Active (WLAN/Ethernet) 64 bit/ 128 bit WEP, WPA, WPA2 One 10/100BaseT with RJ45 connector 7.5V DC Power Adapter Product Name Standard Data Transfer Rate Modulation Method Frequency Band RF Output Power Receiver Sensitivity Operation Range Antenna LED Security LAN interface Power Consumption Operating Temperature 0 ~ 50oC ambient temperature Storage Temperature Humidity Dimension
-20 ~ 70oC ambient temperature 5 to 90 % maximum (non-condensing) 118 x 75 x 25 mm 1 USERS MANUAL OF Wireless 802.11g Multi-mode AP 1.3 Product Features Version: 1.0
Complies with IEEE 802.11b/g standard for 2.4GHz Wireless LAN.
Supports AP/Client/WDS/AP+WDS modes on wireless interfaces.
Supports 64-bit and 128-bit WEP, WPA, WPA2 encryption/decryption function to protect the wireless data transmission.
Supports IEEE 802.1x Authentication.
Support Wi-Fi Protected Access Authentication with Radius and Pre-Shared Key mode.
Supports Inter-Access Point Protocol (IAPP).
Supports Wireless Distribution System (WDS).
Supports IEEE 802.3x full duplex flow control on 10/100M Ethernet interface.
Supports DHCP server to provide clients auto IP addresses assignment.
Supports DHCP client auto IP address assignment from ISP.
Supports clone MAC address function.
Supports WEB based management and configuration.
Supports Log table and remote Log service.
Support Setup Wizard mode. 2 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 1.4 Upper Panel Description Power LED WLAN LED LAN LED Figure 1 Wireless 802.11g Multi-mode AP Upper Panel LED Indicator 1. Power LED 2. WLAN LED 3. LAN LED ACT State On Off Flashing Off Flashing On Off Description The Wireless 802.11g Multi-mode AP is powered on. The Wireless 802.11g Multi-mode AP is powered off. Data is transmitting or receiving on the antenna. No data is transmitting or receiving on the antenna. Data is transmitting or receiving on the LAN interface. Port linked. No link. 3 USERS MANUAL OF Wireless 802.11g Multi-mode AP 1.5 Rear Panel Description Antenna Version: 1.0 Power LAN Reset Figure 2 Wireless 802.11g Multi-mode AP Rear Panel Interfaces 1. Antenna Description The Wireless LAN Antenna.
(Fixed / SMA) 2. Power The power jack allows an external DC +7.5 V power supply 3. LAN connection. The external AC to DC adaptor provide adaptive power requirement to the Wireless 802.11g Multi-mode AP. The RJ-45 sockets allow LAN connection through Category 5 cables. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. 4. Reset Push continually the reset button 5 ~ 10 seconds to reset the configuration parameters to factory defaults. 4 USERS MANUAL OF Wireless 802.11g Multi-mode AP 2 Installation 2.1 Hardware Installation Version: 1.0 Step 1: Place the Wireless 802.11g Multi-mode AP to the best optimum transmission location. The best transmission location for your Wireless 802.11g Multi-mode AP is usually at the geographic center of your wireless network, with line of sign to all of your mobile stations. Step 2: Connect the Wireless 802.11g Multi-mode AP to your wired network. Connect the Ethernet LAN interface of Wireless 802.11g Multi-mode AP by category 5 Ethernet cable to your switch/ hub/ xDSL modem or cable modem. A straight-through Ethernet cable with appropriate cable length is needed. Step 3: Supply DC power to the Wireless 802.11g Multi-mode AP. Use only the AC/DC power adapter supplied with the Wireless 802.11g Multi-mode AP; it may occur damage by using a different type of power adapter. The hardware installation finished. 2.2 Software Installation
There are no software drivers, patches or utilities installation needed, but only the configuration setting. Please refer to chapter 3 for software configuration. Notice: It will take about 55 seconds to complete the boot up sequence after powered on the Wireless 802.11g Multi-mode AP; Power LED will be active, and after that the WLAN Activity LED will be flashing to show the WLAN interface is enabled and working now. 5 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 3 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily. The Wireless 802.11g Multi-mode AP is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.254 Default IP subnet mask: 255.255.255.0 WEB login User Name: <empty>
WEB login Password: <empty>
3.1 Prepare your PC to configure the Wireless 802.11g Multi-mode AP For OS of Microsoft Windows 95/ 98/ Me:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. Note: Windows Me users may not see the Network control panel. If so, select View all Control Panel options on the left side of the window 2. Move mouse and double-click the right button on Network icon. The Network window will appear. 3. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless 802.11g Multi-mode AP.
IP Subnet Mask: 255.255.255.0 8. Click OK and reboot your PC after completes the IP parameters setting. For OS of Microsoft Windows 2000, XP:
1. Click the Start button and select Settings, then click Control Panel. The Control 6 USERS MANUAL OF Wireless 802.11g Multi-mode AP Panel window will appear. Version: 1.0 2. Move mouse and double-click the right button on Network and Dial-up Connections icon. Move mouse and double-click the Local Area Connection icon. The Local Area Connection window will appear. Click Properties button in the Local Area Connection window. 3. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless 802.11g Multi-mode AP.
IP Subnet Mask: 255.255.255.0 8. Click OK to completes the IP parameters setting. For OS of Microsoft Windows NT:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Move mouse and double-click the right button on Network icon. The Network window will appear. Click Protocol tab from the Network window. 3. Check the installed list of Network Protocol window. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless 802.11g Multi-mode AP.
IP Subnet Mask: 255.255.255.0 8. Click OK to complete the IP parameters setting. 7 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 3.2 Connect to the Wireless 802.11g Multi-mode AP Open a WEB browser, i.e. Microsoft Internet Explore, then enter 192.168.1.254 on the URL to connect the Wireless 802.11g Multi-mode AP. 3.3 Management and configuration on the Wireless 802.11g Multi-mode AP 3.3.1 Status This page shows the current status and some basic settings of the device, includes system, wireless, and Ethernet LAN configuration information. Screen snapshot Status Item System Uptime Firmware version Description It shows the duration since Wireless 802.11g Multi-mode AP is powered on. It shows the firmware version of Wireless 802.11g Multi-mode AP. 8 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Wireless configuration Mode Band SSID Channel Number Encryption Associated Clients BSSID Associated Clients TCP/IP Configuration Attain IP Protocol IP Address Subnet Mask Default Gateway MAC Address 3.3.2 Setup Wizard It shows wireless operation mode It shows the current wireless operating frequency. It shows the SSID of this Wireless 802.11g Multi-mode AP. The SSID is the unique name of Wireless 802.11g Multi-mode AP and shared among its service area, so all devices attempts to join the same wireless network can identify it. It shows the wireless channel connected currently. It shows the status of encryption function. It shows the number of connected clients (or stations, PCs). It shows the BSSID address of the Wireless 802.11g Multi-mode AP. BSSID is a six-byte address. It shows total numbers of WLAN clients connected, It shows how the Wireless 802.11g Multi-mode AP gets the IP address. The IP address can be set manually to a fixed one or set dynamically by DHCP server. It shows the IP address of WAN interface of Wireless 802.11g Multi-mode AP. It shows the IP subnet mask of LAN interface of Wireless 802.11g Multi-mode AP. It shows the default gateway setting for outgoing data packets. It shows the MAC address of Wireless 802.11g Multi-mode AP. This page guides you to configure wireless Access Point for first time 9 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot Setup Wizard I LAN Interface Setup This page is used to configure local area network IP address and subnet mask Screen snapshot LAN Interface Setup 10 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 II Wireless Basic Settings This page is used to configure basic wireless parameters like Band, Mode, Network Type SSID, Channel Number, Enable Mac Clone(Single Ethernet Client) Screen snapshot Wireless Basic Settings 11 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 III Wireless Security Setup This page is used to configure wireless security Screen snapshot Wireless Security Setup 3.3.3 Wireless - Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Access Point. Here you may change wireless encryption settings as well as wireless network parameters. 12 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot Wireless Basic Settings Item Disable Wireless LAN Interface Band Mode Description Click on to disable the wireless LAN data transmission. Click to select 2.4GHz(B) / 2.4GHz(G) / 2.4GHz(B+G) Click to select the WLAN AP / Client / WDS / AP+WDS wireless mode. The Site Survey button provides tool to scan the wireless network. If any Access Point or IBSS is found, you could choose to connect it manually when client mode is enabled. Refer to 3.3.9 Site Survey. It is the wireless network name. The SSID can be 32 bytes long. Select the wireless communication channel from pull-down menu. Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address, transmit-packet, receive-packet and transmission-rate for Site Survey SSID Channel Number Associated Clients 13 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Enable Mac Clone
(Single Ethernet Client) Enable Universal Repeater Mode SSID of Extended Interface Apply Changes Reset each associated wireless client. Take Laptop NIC MAC address as wireless client MAC address. [Client Mode only]
Click to enable Universal Repeater Mode Assign SSID when enables Universal Repeater Mode. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 3.3.4 Wireless - Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your Wireless 802.11g Multi-mode AP. Screen snapshot Wireless Advanced Settings 14 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Item Authentication Type Fragment Threshold RTS Threshold Beacon Interval Data Rate Preamble Type Broadcast SSID IAPP 802.11g Protection RF Output Power Turbo Mode Apply Changes Reset Description Click to select the authentication type in Open System, Shared Key or Auto selection. Set the data packet fragmentation threshold, value can be written between 256 and 2346 bytes. Refer to 4.10 What is Fragment Threshold?
Set the RTS Threshold, value can be written between 0 and 2347 bytes. Refer to 4.11 What is RTS(Request To Send) Threshold?
Set the Beacon Interval, value can be written between 20 and 1024 ms. Refer to 4.12 What is Beacon Interval?
Select the transmission data rate from pull-down menu. Data rate can be auto-select, 11M, 5.5M, 2M or 1Mbps. Click to select the Long Preamble or Short Preamble support on the wireless data packet transmission. Refer to 4.13 What is Preamble Type?
Click to enable or disable the SSID broadcast function. Refer to 4.14 What is SSID Broadcast?
Click to enable or disable the IAPP function. Refer to 4.20 What is Inter-Access Point Protocol(IAPP)?
Protect 802.11b user. To adjust transmission power level. Click to enable/disable turbo mode.(Only apply to WLAN IC of Realtek). Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 3.3.5 Wireless - Security Setup This page allows you setup the wireless security. Turn on WEP, WPA, WPA2 by using encryption keys could prevent any unauthorized access to your wireless network. 15 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot Wireless Security Setup Item Encryption Description Select the encryption supported over wireless access. The encryption method can be None, WEP, WPA(TKIP), WPA2 or WPA2 Mixed Refer to 4.9 What is WEP?
4.15 What is Wi-Fi Protected Access (WPA)?
4.16 What is WPA2(AES)?
4.17 What is 802.1X Authentication?
4.18 What is Temporal Key Integrity Protocol (TKIP)?
4.19 What is Advanced Encryption Standard (AES)?
While Encryption is selected to be WEP. Click the check box to enable IEEE 802.1x authentication function. Refer to 4.16 What is 802.1x Authentication?
While Encryption is selected to be WPA. Click to select the WPA Authentication Mode with Enterprise (RADIUS) or Personal (Pre-Shared Key). Refer to 4.15 What is Wi-Fi Protected Access (WPA)?
Enable TKIP or AES. Depends on which encryption you Use 802.1x Authentication WPA Authentication Mode WPA Cipher Suite 16 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 WPA2 Cipher Suite set. Enable TKIP or AES. Depends on which encryption you set. Pre-Shared Key Format While Encryption is selected to be WPA. Pre-Shared Key Enable Pre-Authentication Authentication RADIUS Server Apply Changes Reset Select the Pre-shared key format from the pull-down menu. The format can be Passphrase or Hex (64 characters). [WPA, Personal(Pre-Shared Key) only]
Fill in the key value. [WPA, Personal(Pre-Shared Key) only]
Click to enable Pre-Authentication. [WPA2/WPA2 Mixed only, Enterprise only]
Set the IP address, port and login password information of authentication RADIUS sever. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. I WEP Key Setup Screen snapshot WEP Key Setup Item Description 17 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Key Length Key Format Default Tx Key Encryption Key 1 Encryption Key 2 Encryption Key 3 Encryption Key 4 Apply Changes Close Reset Select the WEP shared secret key length from pull-down menu. The length can be chose between 64-bit and 128-bit (known as WEP2) keys. The WEP key is composed of initialization vector (24 bits) and secret key (40-bit or 104-bit). Select the WEP shared secret key format from pull-down menu. The format can be chose between plant text
(ASCII) and hexadecimal (HEX) code. Set the default secret key for WEP security function. Value can be chose between 1 and 4. Secret key 1 of WEP security encryption function. Secret key 2 of WEP security encryption function. Secret key 3 of WEP security encryption function. Secret key 4 of WEP security encryption function. Click the Apply Changes button to complete the new configuration setting. Click to close this WEP Key setup window. Click the Reset button to abort change and recover the previous configuration setting. WEP encryption key (secret key) length:
Length ASCII HEX 64-bit 5 characters 128-bit 13 characters 10 hexadecimal codes 26 hexadecimal codes Format 3.3.6 Wireless - Access Control If you enable wireless access control, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When this option is enabled, no wireless clients will be able to connect if the list contains no entries. 18 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot Wireless Access Control Item Wireless Access Control Mode Description Click the Disabled, Allow Listed or Deny Listed of drop down menu choose wireless access control mode. This is a security control function; only those clients registered in the access control list can link to this Wireless 802.11g Multi-mode AP. Fill in the MAC address of client to register this Wireless 802.11g Multi-mode AP access capability. Fill in the comment tag for the registered client. Click the Apply Changes button to register the client to new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. It shows the registered clients that are allowed to link to this Wireless 802.11g Multi-mode AP. Click to delete the selected clients that will be access right removed from this Wireless 802.11g Multi-mode AP. Click to delete all the registered clients from the access allowed list. MAC Address Comment Apply Changes Reset Current Access Control List Delete Selected Delete All 19 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Reset 3.3.7 WDS Settings Click the Reset button to abort change and recover the previous configuration setting. Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other AP that you want to communicate with in the table and then enable the WDS. Screen snapshot WDS Setup Item Enable WDS MAC Address Comment Apply Changes Reset Description Click the check box to enable wireless distribution system. Refer to 4.21 What is Wireless Distribution System (WDS)?
Fill in the MAC address of AP to register the wireless distribution system access capability. Fill in the comment tag for the registered AP. Click the Apply Changes button to register the AP to new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 20 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Set Security Show Statistics Delete Selected Delete All Reset Click button to configure wireless security like WEP(64bits), WEP(128bits), WPA(TKIP), WPA2(AES) or None It shows the TX, RX packets, rate statistics Click to delete the selected clients that will be removed from the wireless distribution system. Click to delete all the registered APs from the wireless distribution system allowed list. Click the Reset button to abort change and recover the previous configuration setting. I WDS Security Setup Requirement: Set [Wireless]->[Basic Settings]->[Mode]->AP+WDS This page is used to configure the wireless security between APs. Refer to 3.3.6 Wireless Security Setup. Screen snapshot WDS Security Setup II WDS AP Table This page is used to show WDS statistics 21 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot WDS AP Table Item MAC Address Tx Packets Tx Errors Rx Packets Tx Rare (Mbps) Refresh Close 3.3.8 Site Survey Description It shows the MAC Address within WDS. It shows the statistic count of sent packets on the wireless LAN interface. It shows the statistic count of error sent packets on the Wireless LAN interface. It shows the statistic count of received packets on the wireless LAN interface. It shows the wireless link rate within WDS. Click to refresh the statistic counters on the screen. Click to close the current window. This page is used to view or configure other APs near yours. 22 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot Wireless Site Survey Item SSID BSSID Channel Type Encrypt Signal Select Refresh Description It shows the SSID of AP. It shows BSSID of AP. It show the current channel of AP occupied. It show which type AP acts. It shows the encryption status. It shows the power level of current AP. Click to select AP or client youd like to connect. Click the Refresh button to re-scan site survey on the screen. Click the Connect button to establish connection. Connect 3.3.9 TCP/IP Settings This page is used to configure the parameters for local area network that connects to the LAN ports of your Wireless 802.11g Multi-mode AP. Here you may change the setting for IP address, subnet mask, DHCP, etc. 23 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Screen snapshot LAN Interface Setup Item IP Address Description Fill in the IP address of LAN interfaces of this Wireless 802.11g Multi-mode AP. Fill in the subnet mask of LAN interfaces of this Wireless 802.11g Multi-mode AP. Fill in the default gateway for LAN interfaces out going data packets. Click to select Disabled, Client or Server in different operation mode of wireless Access Point. Fill in the start IP address and end IP address to allocate a range of IP addresses; client with DHCP function set will be assigned an IP address from the range. Click to open the Active DHCP Client Table window that shows the active clients with their assigned IP address, MAC address and time expired information. [Server mode only]
Manual setup DNS server IP address. Subnet Mask Default Gateway DHCP DHCP Client Range Show Client DNS Server 24 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Domain Name Assign Domain Name and dispatch to DHCP clients. It is optional field. 802.1d Spanning Tree Select to enable or disable the IEEE 802.1d Spanning Tree function from pull-down menu. Fill in the MAC address that is the MAC address to be cloned. Refer to 4.24 What is Clone MAC Address?
Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. Clone MAC Address Apply Changes Reset 3.3.10 Log This page is used to configure the remote log server and shown the current log. Screen snapshot Log Item Enable Log System all Wireless only Description Click the checkbox to enable log. Show all log of wireless Access Point. Only show wireless log. 25 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Enable Remote Log Log Server IP Address Apply Changes Refresh Clear 3.3.11 Statistics Click the checkbox to enable remote log service. Input the remote log IP address Click the Apply Changes button to save above settings. Click the refresh the log shown on the screen. Clear log display screen This page shows the packet counters for transmission and reception regarding to wireless and Ethernet LAN networks. Screen snapshot Statistics Item Wireless LAN Sent Packets Wireless LAN Received Packets Ethernet LAN Sent Packets Ethernet LAN Received Packets Refresh Description It shows the statistic count of sent packets on the wireless LAN interface. It shows the statistic count of received packets on the wireless LAN interface. It shows the statistic count of sent packets on the Ethernet LAN interface. It shows the statistic count of received packets on the Ethernet LAN interface. Click the refresh the statistic counters on the screen. 26 USERS MANUAL OF Wireless 802.11g Multi-mode AP 3.3.12 Upgrade Firmware Version: 1.0 This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system. Screen snapshot Management - Upgrade Firmware Item Select File Description Click the Browse button to select the new version of web firmware image file. Click the Upload button to update the selected web firmware image to the Wireless 802.11g Multi-mode AP. Click the Reset button to abort change and recover the previous configuration setting. Upload Reset 3.3.13 Save/ Reload Settings This page allows you save current settings to a file or reload the settings from the file that was saved previously. Besides, you could reset the current configuration to factory default. Screen snapshot Management - Save/Reload Settings 27 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 Item Save Settings to File Description Click the Save button to download the configuration parameters to your personal computer. Load Settings from File Click the Browse button to select the configuration files then click the Upload button to update the selected configuration to the Wireless 802.11g Multi-mode AP. Click the Reset button to reset the configuration parameter to factory defaults. Reset Settings to Default 3.3.14 Password Setup This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection.
+
Screen snapshot Management - Password Setup Description Item Fill in the user name for web management login control. User Name Fill in the password for web management login control. New Password Confirmed Password Because the password input is invisible, so please fill in Apply Changes Reset the password again for confirmation purpose. Clear the User Name and Password fields to empty, means to apply no web management login control. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 28 USERS MANUAL OF Wireless 802.11g Multi-mode AP 3.3.15 Logout Version: 1.0 This page is used to logout web management page. This item will be activated next time you login after you define user account and password. Screen snapshot Logout Screen snapshot Logout - OK Item Apply Change Description Click the Apply Change button, Then click OK button to logout. 29 USERS MANUAL OF Wireless 802.11g Multi-mode AP 4 Frequently Asked Questions (FAQ) Version: 1.0 4.1 What and how to find my PCs IP and MAC address?
IP address is the identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 191.168.1.254 could be an IP address. The MAC (Media Access Control) address is your computer's unique hardware number.
(On an Ethernet LAN, it's the same as your Ethernet address.) When you're connected to the Internet from your computer (or host as the Internet protocol thinks of it), a correspondence table relates your IP address to your computer's physical (MAC) address on the LAN. To find your PCs IP and MAC address,
Open the Command program in the Microsoft Windows.
Type in ipconfig /all then press the Enter button.
Your PCs IP address is the one entitled IP Address and your PCs MAC address is the one entitled Physical Address. 4.2 What is Wireless LAN?
A wireless LAN (WLAN) is a network that allows access to Internet without the need for any wired connections to the users machine. 4.3 What are ISM bands?
ISM stands for Industrial, Scientific and Medical; radio frequency bands that the Federal Communications Commission (FCC) authorized for wireless LANs. The ISM bands are located at 915 +/- 13 MHz, 2450 +/- 50 MHz and 5800 +/- 75 MHz. 4.4 How does wireless networking work?
The 802.11 standard define two modes: infrastructure mode and ad hoc mode. In infrastructure mode, the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations. This configuration is called a Basic Service Set (BSS). An Extended Service Set (ESS) is a set of two or more BSSs forming a single subnetwork. Since most corporate WLANs require access 30 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 to the wired LAN for services (file servers, printers, Internet links) they will operate in infrastructure mode. Example 1: wireless Infrastructure Mode Ad hoc mode (also called peer-to-peer mode or an Independent Basic Service Set, or IBSS) is simply a set of 802.11 wireless stations that communicate directly with one another without using an access point or any connection to a wired network. This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services, such as a hotel room, convention center, or airport, or where access to the wired network is barred (such as for consultants at a client site). Example 2: wireless Ad Hoc Mode 4.5 What is BSSID?
A six-byte address that distinguishes a particular a particular access point from others. Also know as just SSID. Serves as a network ID or name. 4.6 What is ESSID?
The Extended Service Set ID (ESSID) is the name of the network you want to access. It is used to identify different wireless networks. 31 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 4.7 What are potential factors that may causes interference?
Factors of interference:
Obstacles: walls, ceilings, furniture etc.
Building Materials: metal door, aluminum studs.
Electrical devices: microwaves, monitors and electrical motors. Solutions to overcome the interferences:
Minimizing the number of walls and ceilings.
Position the WLAN antenna for best reception.
Keep WLAN devices away from other electrical devices, eg: microwaves, monitors, electric motors, etc.
Add additional Wireless 802.11g Multi-mode APs if necessary. 4.8 What are the Open System and Shared Key authentications?
IEEE 802.11 supports two subtypes of network authentication services: open system and shared key. Under open system authentication, any wireless station can request authentication. The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station. The receiving station then returns a frame that indicates whether it recognizes the sending station. Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel. 4.9 What is WEP?
An optional IEEE 802.11 function that offers frame transmission privacy similar to a wired network. The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers. WEP relies on a secret key that is shared between a mobile station (e.g. a laptop with a wireless Ethernet card) and an access point (i.e. a base station). The secret key is used to encrypt packets before they are transmitted, and an integrity check is used to ensure that packets are not modified in transit. 4.10 What is Fragment Threshold?
The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several 32 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 fragments each of size equal to fragment threshold. By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead. Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented. If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible. 4.11 What is RTS (Request To Send) Threshold?
The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance. 4.12 What is Beacon Interval?
In addition to data frames that carry information from higher layers, 802.11 includes management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling 33 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). 4.13 What is Preamble Type?
There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and the short is 56 bits. 4.14 What is SSID Broadcast?
Broadcast of SSID is done in access points by the beacon. This announces your access point (including various bits of information about it) to the wireless world around it. By disabling that feature, the SSID configured in the client must match the SSID of the access point. Some wireless devices don't work properly if SSID isn't broadcast (for example the D-link DWL-120 USB 802.11b adapter). Generally if your client hardware supports operation with SSID disabled, it's not a bad idea to run that way to enhance network security. However it's no replacement for WEP, MAC filtering or other protections. 4.15 What is Wi-Fi Protected Access (WPA)?
Wi-Fis original security mechanism, Wired Equivalent Privacy (WEP), has been viewed as insufficient for securing confidential business communications. A longer-term solution, the IEEE 802.11i standard, is under development. However, since the IEEE 802.11i standard is not expected to be published until the end of 2003, several members of the WI-Fi Alliance teamed up with members of the IEEE 802.11i task group to develop a significant near-term enhancement to Wi-Fi security. Together, this team developed Wi-Fi Protected Access. To upgrade a WLAN network to support WPA, Access Points will require a WPA software upgrade. Clients will require a software upgrade for the network interface card, and possibly a software update for the operating system. For enterprise networks, an 34 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 authentication server, typically one that supports RADIUS and the selected EAP authentication protocol, will be added to the network. 4.16 What is WPA2?
It is the second generation of WPA. WPA2 is based on the final IEEE 802.11i amendment to the 802.11 standard. 4.17 What is 802.1x Authentication?
802.1x is a framework for authenticated MAC-level access control, defines Extensible Authentication Protocol (EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for dial-up authentication with Point-to-Point Protocol in RFC 2284. Beyond encapsulating EAP packets, the 802.1x standard also defines EAPOL messages that convey the shared key information critical for wireless security. 4.18 What is Temporal Key Integrity Protocol (TKIP)?
The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard for wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP. 4.19 What is Advanced Encryption Standard (AES)?
Security issues are a major concern for wireless LANs, AES is the U.S. governments next-generation cryptography algorithm, which will replace DES and 3DES. 4.20 What is Inter-Access Point Protocol (IAPP)?
The IEEE 802.11f Inter-Access Point Protocol (IAPP) supports Access Point Vendor interoperability, enabling roaming of 802.11 Stations within IP subnet. IAPP defines messages and data to be exchanged between Access Points and between the IAPP and high layer management entities to support roaming. The IAPP protocol uses TCP for inter-Access Point communication and UDP for RADIUS request/response exchanges. It also uses Layer 2 frames to update the forwarding tables of Layer 2 devices. 35 USERS MANUAL OF Wireless 802.11g Multi-mode AP Version: 1.0 4.21 What is Wireless Distribution System (WDS)?
The Wireless Distribution System feature allows WLAN AP to talk directly to other APs via wireless channel, like the wireless bridge or repeater service. 4.22 What is Clone MAC Address?
Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address. Since that all the clients will communicate outside world through the Wireless 802.11g Multi-mode AP, so have the cloned MAC address set on the Wireless 802.11g Multi-mode AP will solve the issue. 36
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2006-09-20 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2006-09-20
|
||||
1 | Applicant's complete, legal business name |
SparkLAN Communications, Inc.
|
||||
1 | FCC Registration Number (FRN) |
0015463375
|
||||
1 | Physical Address |
8F., No.257, Sec. 2, Tiding Blvd., Neihu District
|
||||
1 |
Taipei, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
RYK
|
||||
1 | Equipment Product Code |
WAPR141
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
G**** L******
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
+886-******** Extension:
|
||||
1 | Fax Number |
+886-********
|
||||
1 |
g******@sparklan.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation (Hwa Ya)
|
||||
1 | Name |
G**** C****
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
G******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation
|
||||
1 | Name |
E******** W****
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
e******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless 802.11g Multi-mode AP | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R******** C****
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0720000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC