FCC ID: S9NBNRGM0AL Bluetooth Low Energy Module

BLUENRG-M0A, BLUENRG-M0L Very low power network processor module for Bluetooth low energy v4.2 Datasheet - production data On-board chip antenna Operating supply voltage: from 1.7 to 3.6 V Operating temperature range: -40 C to 85 C Applications Watches Fitness, wellness and sports Consumer medical Security/proximity Remote control Home and industrial automation Assisted living Mobile phone peripherals PC peripherals Description The BLUENRG-M0x is an easy to use Bluetooth low energy master/slave network processor module, compliant with Bluetooth v4.2. The BLUENRG-M0x module supports multiple roles simultaneously, and can act at the same time as Bluetooth low energy sensor and hub device. The entire Bluetooth low energy stack and protocols are embedded into BLUENRG-M0x module. The external host application processor, where the application resides, is connected to the BLUENRG-M0x module through a standard SPI interface. The BLUENRG-M0x module provides a complete RF platform in a tiny form factor. Radio, antenna, high frequency and LPO oscillators are integrated to offer a certified solution to optimize the time to market of the final applications. The BLUENRG-M0x can be powered directly with a standard 3 V coin cell battery, a pair of AAA batteries or any power source from 1.7 to 3.6 V. Features Bluetooth v4.2 compliant Supports master and slave modes Multiple roles supported simultaneously Embedded Bluetooth low energy protocol stack GAP, GATT, SM, L2CAP, LL, RFPHY Bluetooth low energy profiles provided separately Embedded ST BlueNRG-MS network processor

+5.31 dBm available e.i.r.p. output power Down to -88 dBm Rx sensitivity Up to 94 dB link budget with excellent link reliability Host interface SPI, IRQ, and RESET On-field stack upgrading available via SPI AES security co-processor Certification CE qualified FCC, IC modular approval certified ARIB qualified BQE qualified December 2018 DocID027851 Rev 1.0 1/19 www.st.com Contents Contents Contents BLUENRG-M0x Applications ........................................................................................................................... 1 Features 1 Description ............................................................................................................................ 1 1 2 3 3.1 4 4.1 4.2 5 5.1 5.2 5.3 5.4 6 7 7.1 8 8.1 General description .................................................................................. 4 Block diagram ........................................................................................... 5 Software architecture ............................................................................... 6 Bluetooth firmware implementation .................................................................. 6 General characteristics ............................................................................ 7 Absolute maximum ratings ................................................................................ 7 Operating conditions .......................................................................................... 7 Electrical specification ............................................................................. 8 Electrical characteristics .................................................................................... 8 Digital I/O specifications ..................................................................................... 9 RF General characteristics ................................................................................. 9 Pin assignment.................................................................................................. 10 Mechanical dimensions.......................................................................... 11 Hardware design ..................................................................................... 11 Reflow soldering ............................................................................................... 11 Regulatory compliance .......................................................................... 13 FCC certification ............................................................................................... 13 8.1.1 Labeling instructions....................................................................... 13 8.1.2 Product manual instructions ........................................................... 14 8.2 IC certification ................................................................................................... 15 2/19 DocID027851 Rev 1.0 Contents BLUENRG-M0x 8.2.1 Labeling instructions....................................................................... 15 8.2.2 Product manual instructions ........................................................... 15 8.3 8.4 9 10 11 12 CE certification .................................................................................................. 16 Bluetooth certification ...................................................................................... 17 Ordering information .............................................................................. 17 ECOPACK

.............................................................................................. 18 Traceability .............................................................................................. 18 Revision history ...................................................................................... 18 3/19 DocID027851 Rev 1.0 BLUENRG-M0x Software architecture 1 General description The BLUENRG-M0x is a single-mode Bluetooth low energy master/slave network processor module compliant with Bluetooth v4.2. The BLUENRG-M0x module integrates a 2.4 GHz RF radio the ST BlueNRG-MS on which a complete power-optimized stack for Bluetooth single mode protocol runs, providing

- Master, slave role support

- GAP: central, peripheral, observer or broadcaster roles

-

-

-

-

ATT/GATT: client and server SM: privacy, authentication and authorization L2CAP Link Layer: AES-128 encryption and decryption The BlueNRG-MS radio embeds nonvolatile Flash memory allows on-field stack upgrading. In addition, according the Bluetooth specification v4.2 the BLUENRG-M0x module provides:

- Multiple roles simultaneously support

-

-

-

-

-

-

-

-

Support simultaneous advertising and scanning Support being slave of up to two masters simultaneously Privacy V1.1 Low duty cycle directed advertising Connection parameters request procedure LE Ping 32 bits UUIDs L2CAP connection oriented channels The BLUENRG-M0x module is equipped with Bluetooth low energy profiles in C source code, available for the ST radio BlueNRG-MS. The external host application processor, where the application resides, is interfaced with the BLUENRG-M0x module through an application controller interface protocol, which is based on a standard SPI interface. The BLUENRG-M0x module enables wireless connectivity into electronic devices, not requiring any RF experience or expertise for integration into the final product. The BLUENRG-M0x module provides a complete RF platform in a tiny form factor and being a certified solution optimizes the time to market of the final applications. The BLUENRG-M0x module allows applications to meet of the tight advisable peak current requirements imposed with the use of standard coin cell batteries. Optimized results are obtained when the embedded high-efficiency DC-DC step-down converter is used (BLUENRG-M0A). Instead, for the BLUENRG-M0L the best performances in terms of power consumption are achieved using a 1.8V DC power supply. BLUENRG-M0x can be powered directly with a standard 3 V coin cell battery, a pair of AAA batteries or any power source from 1.7 to 3.6 V. ST may update the FW provided with the modules at any time. ST recommends that users regularly check for documentation and the current FW version available at www.st.com/bluemodules. 4/19 DocID027851 Rev 1.0 BLUENRG-M0x Software architecture 2 Block diagram Figure 1a. HW block diagram for BLUENRG-M0A Figure 1b. HW block diagram for BLUENRG-M0L 5/19 DocID027851 Rev 1.0 BLUENRG-M0x 3 Software architecture Software architecture 3.1 Bluetooth firmware implementation The BlueNRG-M0x modules have been designed to work with an external Host processor. The external Host application processor, where the application resides, is interfaced with the BlueNRG-MS inside the BlueNRG-M0x modules through an application controller interface (ACI) protocol which is based on a standard SPI slave interface as transport layer, basing in five physical wires:

2 control wires (Clock and Chip Select) 2 data wires with serial shift-out (MOSI and MISO) in full duplex 1 wire to indicate data availability from the slave (IRQ) All the SPI pins have an internal pull-down except for the CS that has a pull-up. All the SPI pins, except the CS, are in high impedance state during the low-power states. The IRQ pin needs a pull-down external resistor. Figure 2. BLUENRG-M0A and BLUENRG-M0L application block diagram 6/19 DocID027851 Rev 1.0 BLUENRG-M0x 4 General characteristics 4.1 Absolute maximum ratings Table 1. Absolute maximum ratings Rating Min Typ. Max Unit Storage temperature range Supply voltage, VIN I/O pin Voltage (VIO five-volt tolerant pin) RF saturation input power

-40

-0.3

-0.3

-

-

-

-

8

+85 3.9 3.9

-

VESD-HBM Electrostatic discharge voltage 2.0 kV C V V dBm kV 4.2 Operating conditions Table 2. Operating conditions Rating Min Typ. Max Unit Storage temperature range Operating ambient temperature range Supply voltage, VIN Signals & I/O pin voltage

(according supply voltage) Frequency range

-40

-40 1.7 1.7 2402

-

-

3.3

-

-

+85

+85 3.6 3.6 C C V V 2480 MHz 7/19 DocID027851 Rev 1.0 BLUENRG-M0x 5 Electrical specification 5.1 Electrical characteristics Characteristic measured over recommended operating condition unless otherwise specified. Typical value are referred to VIN= 3.3 V, 25 C, SMPS on, XO 32KHz and 32MHz. Table 2a. Electrical characteristics for the BLUENRG-M0A Symbol Parameter Test conditions Min. Typ. Max. Unit Reset Standby Sleep mode: 32 kHz XO ON (12 KB retention RAM) Mode 1 Sleep mode: 32 kHZ XO ON (24 KB retention RAM) Mode 2 Active mode IDD Supply current RX TX +8 dBm TX +4 dBm TX +2 dBm TX -2 dBm TX -5 dBm TX -8 dBm TX -11 dBm TX -14 dBm 5 1.8 1.7 2.2 2.12 9.36 16.50 12.04 10.40 9.44 8.79 8.29 8.01 7.82 nA uA A mA mA mA mA mA mA mA mA mA mA Characteristic measured over recommended operating condition unless otherwise specified. Typical value are referred to VIN= 3.3 V, 25 C, SMPS off, RO 32KHz and 32MHz. Symbol Parameter Test conditions Min. Typ. Max. Unit Table 2b. Electrical characteristics for the BLUENRG-M0L Reset Standby Sleep mode: 32 kHz RO ON (12 KB retention RAM) Mode 1 Sleep mode: 32 kHZ RO ON (24 KB retention RAM) Mode 2 Active mode IDD Supply current RX TX +8 dBm TX +4 dBm TX +2 dBm 8/19 DocID027851 Rev 1.0 N/A 1.7 2.8 3.2 2.54 16.36 29.16 21.3 18.29 nA uA A mA mA mA mA mA BLUENRG-M0x TX -2 dBm TX -5 dBm TX -8 dBm TX -11 dBm TX -14 dBm 16.44 15.18 14.19 13.61 13.25 mA mA mA mA mA 5.2 Digital I/O specifications IO pins are directly connected to the embedded state of the art BlueNRG-MS chipset. For more details about the digital I/I specification, please refer directly to the BlueNRG-MS datasheet available on www.st.com. 5.3 RF General characteristics Characteristic measured over recommended operating condition unless otherwise specified. Typical value are referred to VIN= 3.3 V, 25 C, DC/DC on, XO 32KHz and XO 32MHz. Table 2. Electrical characteristics Symbol Parameter Test conditions Min. Typ. Max. Unit FREQ FCH RFch Frequency range Channel spacing RF Channel center frequency 2400

-

2402

-

2

-

2483.5 MHz

-

MHz 2480 MHz 9/19 DocID027851 Rev 1.0 BLUENRG-M0x 5.4 Pin assignment Figure 8. Pin connection Name Type Pin #

Description V max. Tolerant Table 5. Pin assignment SPI_IRQ SPI_CLK SPI_MISO SPI_MOSI SPI_CS Vin GND BT_RESET EXT_LPCLK GPIO2 ANA TEST 0 O I O I I I I I/O I SPI Interface SPI IRQ (SLAVE has data for MASTER) SPI CLOCK (Max. 8 MHz) SPI MISO (MASTER in / SLAVE out) SPI MOSI (MASTER out SLAVE in) 4 7 8 9 10 SPI Chip select (SPI slave select) Vin Vin Vin Vin Vin Power and ground 5 6 Vin GND Reset

(1.7V - 3.6V max.) 11 Reset input (active low < 0.35 Vin)

(1.7V - 3.6V max.) LPO 1 2 3 Not connected Not connected Not connected 10/19 DocID027851 Rev 1.0 BLUENRG-M0x 6 Mechanical dimensions Figure 9. Mechanical dimensions Figure 10. Recommend land pattern top view 7 Hardware design BLUENRG-M0x module supports SPI hardware interfaces. Note:

- All unused pins should be left floating; do not ground.

- All GND pins must be well grounded.

- The area around the module should be free of any ground planes, power planes, trace routings, or metal for 6 mm from the module antenna position, in all directions.

- Traces should not be routed underneath the module. 7.1 11/19 Reflow soldering DocID027851 Rev 1.0 BLUENRG-M0x The BLUENRG-M0x is a high temperature strength surface mount Bluetooth module supplied on a 11 pin, 4-layer PCB. The final assembly recommended reflow profiles are indicated here below. Soldering phase has to be executed with care: in order to avoid undesired melting phenomenon, particular attention has to be taken on the set up of the peak temperature. Here following some suggestions for the temperature profile based on following recommendations. Table 6. Soldering profile Profile feature Average ramp up rate (TSMAX to Tp) Preheat Temperature min (TS mn) Temperature max (TS max) Time (tS min to tS max) (tS) Time maintained above:

Temperature TL Time tL Peak temperature (TP) Time within 5 C of actual peak temperature (TP) Ramp down rate PB-free assembly 3C/ sec max 150 C 200 C 60-100 sec 217 C 60-70 sec 240 + 0 C 10-20 sec 6 C/sec Time from 25 C to peak temperature 8 minutes max Figure 11. Soldering profiles 12/19 DocID027851 Rev 1.0 BLUENRG-M0x 8 8.1 Regulatory compliance FCC certification This module has been tested and found to comply with the FCC part 15.247 rules. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This device may not cause harmful interference, and this device must accept any interference received, including interference that However, there is no guarantee that interference may not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. 2. may cause undesired operation. Modifications or changes to this equipment not expressly approved by STMicroelectronics may render void the user's authority to operate this equipment. In addition, the RF exposure compliance distance of the BLUENRG-M0x is set equal to 15 mm, as shown in the following Tables. The device is compliant with part 15.247 of Title 47 of the FCC rules. If the Link Module is integrated into a new host product, the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. If the module is integrated into a new host product, the should follow FCC KDB 996369 D04 Module Integration Guide. Modular approval FCC ID: S9NBNRGM0AL In accordance with FCC part 15, the BLUENRG-M0x is listed as a modular transmitter device. This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with colocation and RF exposure requirements in accordance with FCC multi-transmitter product procedures. Collocated transmitters operating in portable RF Exposure conditions (e.g. <20 cm from persons including but not limited to body worn and hand held devices) may require separate approval. 8.1.1 Labeling instructions When integrating the BLUENRG-M0x into the final product, the OEM must ensure that the FCC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning):

Contains FCC ID: S9NBNRGM0AL OR This product contains FCC ID: S9NBNRGM0AL The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches):

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

13/19 DocID027851 Rev 1.0 BLUENRG-M0x this device may not cause harmful interference, and this device must accept any interference received, including any interference that may cause undesired operation. 8.1.2 Product manual instructions This section applies to OEM final products containing the BLUENRG-M0x module, subject to FCC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning):

Note:

Note:

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (Part. 15.21) In the case where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. In the case where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. 14/19 DocID027851 Rev 1.0 BLUENRG-M0x 8.2 IC certification This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. In addition, accordingly to RSS-102 clause 2.6, the RF exposure compliance distance of the BLUENRG-M0x is set equal to 15 mm, as shown in the following Tables. Modular approval IC: 8976C-BNRGM0AL In accordance with IC RSS-247, the BLUENRG-M0x is listed as a modular transmitter device. This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with colocation and RF exposure requirements in accordance with IC multi-transmitter product procedures. Collocated transmitters operating in portable RF Exposure conditions (e.g. <20cm from persons including but not limited to body worn and hand held devices) may require separate approval. 8.2.1 Labeling instructions When integrating the BLUENRG-M0x into the final product, the OEM must ensure that the IC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates that the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning):

Contains IC: 8976C-BNRGM0AL OR This product contains IC: 8976C-BNRGM0AL The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches):

This device complies with RSS-247 of the IC Rules. Operation is subject to the following two conditions:

and this device may not cause harmful interference, this device must accept any interference received, including any interference that may cause undesired operation. Product manual instructions 8.2.2 This section applies to OEM final products containing the BLUENRG-M0x module, subject to IC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning):

15/19 DocID027851 Rev 1.0 BLUENRG-M0x Note:

Note:

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (RSS-247) In the case where an OEM seeks Class B (residential) limits for the final product, the following statement must be included in the final product manual:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to RSS-247 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. In the case where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to RSS-247 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense. 8.3 CE certification The BLUENRG-M0x module has been certified according to the following certification rules:

EN 300 328 V 2.1.1 (2016-11)(a) ETSI EN 301 489-17 V3.1.1 (2017-02)(b) ETSI EN 301 489-1 V2.1.1 (2017-02)(c) 16/19 DocID027851 Rev 1.0 BLUENRG-M0x EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013(d) EN 62311:2008 The module is provided by CE marking:

The module has obtained the RED certificate: No. TBD (under review) The Certificate of Conformity is available / downloadable at the following web page:

www.ST.com/product/bluenrg-m0a and www.ST.com/product/bluenrg-m0l The certified module production firmware release is: 7.X For additional information please refer to:

STMicroelectronics Via C. Olivetti 2, Agrate Brianza 20864 (ITALY) 8.4 Bluetooth certification The module with embedded stack and profile has been qualified in accordance with SIG qualification rules:

Declaration ID: TBD (under review) Qualified design ID: TBD (under review) Product type: End Product Core spec version: 4.2 Product description: Bluetooth low energy v4.2 module a. ETSI EN 300 328 V 2.1.1 (2016 11): electromagnetic compatibility and radio spectrum Matters (ERM);

Wideband transmission systems; data transmission equipment operating in the 2.4 GHZ ISM band and using wideband modulation techniques; harmonized EN covering essential requirements under article 3.2 of the R&TTE directive. b. ETSI EN 301 489-17 V 3.1.1 (2017 02): electromagnetic compatibility and radio spectrum Matters (ERM);

electromagnetic compatibility (EMC) standard for radio equipment and services; part 17: specific condition for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment. c. ETSI EN 301 489-1 V2.1.1 (2017 02): electromagnetic compatibility and radio spectrum Matters

(ERM); electromagnetic compatibility (EMC) standard for radio equipment and services; part 1:

Common technical requirements. d. EN60950-1:2006 +A11:2009+A1:2010+A12:2011+A2:2013: Information technology equipment - safety. 9 Ordering information Table 7. Ordering information Order code Description Packing MOQ BLUENRG-M0A Bluetooth V4.2 low energy Tape and reel 1000 pcs module BLUENRG-M0L Bluetooth V4.2 low energy Tape and reel 1000 pcs module 17/19 DocID027851 Rev 1.0 BLUENRG-M0x 10 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at:

www.st.com. ECOPACK is an ST trademark. 11 Traceability Each module is univocally identified by serial number stored in a 2D data matrix laser marked on the top side (shield) of the module itself. Each module bulk is identified by a bulk ID. BULK ID and module 2D data matrix are linked by a reciprocal traceability link. The module 2D data matrix traces the lot number of any raw material used. 12 Revision history Table 9. Document revision history Date Revision Changes 23-Nov-2018 04-Apr-2019 1 2 Initial release. Second release. 18/19 DocID027851 Rev 1.0 BLUENRG-M0x IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (ST) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to STs terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. 2017 STMicroelectronics All rights reserved 19/19 DocID027851 Rev 1.0 Le module BLUENRG-M0x a t test et dclar conforme avec la section 15.247 de la Rglementation FCC. Ces limitations sont stipules afin de procurer une protection raisonnable contre les interfrences gnantes dans les installations approuves. Cet appareil gnre, utilise et diffuse des ondes radio et, sil nest pas install et utilis en conformit avec les instructions dont il fait lobjet, peut causer des interfrences gnantes sur les communications radio. Il ny a cependant pas de garantie quune interfrence ne se produira pas dans une installation particulire. Cet appareil est en conformit avec la section 15 des rglements FCC. Lutilisation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interfrences nocives, et (2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir. Tout changement ou modification fait(e) cet appareil et non expressment approuv(e) par STMicroelectronics peut annuler lautorisation pour lutilisateur de faire fonctionner lappareil. En outre, la distance de conformit d'exposition RF du BLUENRG-M0x est fixe 15 mm, comme indiqu dans les tableaux suivants. Lappareil est conforme la partie 15.247 du titre 47 des rgles de la FCC. Si le module de liaison est intgr un nouveau produit hte, le produit hte final ncessite toujours des tests de conformit de la partie 15, sous-partie B avec le transmetteur modulaire install. Si le module est intgr un nouveau produit hte, le doit suivre le Guide d'intgration du module FCC KDB 996369 D04. Approbation du module FCC ID: S9NBNRGM0AL Conformment la section 15 des rglements FCC, le module BLUENRG-M0x est rpertori comme un dispositif metteur modulaire. Ce module nest valu que pour une utilisation autonome. Les produits finis incorporant plusieurs metteurs doivent tre conformes la colocation et aux exigences d'exposition RF en concordance avec les procdures FCC multi-metteurs. Dautres metteurs fonctionnant dans des dispositifs portables exposs aux RF (par exemple, situs moins de 20 cm des personnes avec dispositifs portatifs ou ports contre le corps) peuvent ncessiter d'une approbation spare. A.1.1 Instructions d'tiquetage Lors de l'intgration du module BLUENRG-M0x dans le produit final, le fabricant doit sassurer que les exigences en matire d'tiquetage de la FCC sont satisfaites. Une dclaration doit tre place sur ltiquette extrieure du produit final indiquant que le produit comprend un module certifi. L'tiquette doit comporter les informations suivantes (ou une mention analogue que recouvre la mme notion):

Contient FCC ID: S9NBNRGM0AL ou Ce produit contient FCC ID: S9NBNRGM0AL Le sous-traitant doit inclure les noncs suivants sur ltiquette extrieure du produit final moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces):

Cet appareil est en conformit avec la section 15 des rglements FCC. Lutilisation est soumise aux deux conditions suivantes:

(1) cet appareil ne doit pas causer d'interfrences nocives, et

(2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir. A.1.2 Instructions pour lutilisation du produit La prsente section concerne les produits finis contenant le module BLUENRG-M0x, assujettis aux normes FCC. Le manuel du produit final doit contenir la dclaration suivante (ou une mention analogue que recouvre la mme notion):

Avertissement: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet quipement.

(Section 15.21) Dans le cas o le produit finis dun fabriquant OEM rentre dans les limites de la Classe B

(rsidentiel), les noncs suivants doivent tre inclus dans le manuel du produit finis:

"Remarque : Cet quipement a t test et dclar conforme aux limitations prvues dans le cadre de la classe B des appareils numriques, dfinies par la section 15 du rglement de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre toute interfrence dangereuse issue d'une installation rsidentielle. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il se peut que des interfrences se produisent dans une installation particulire. Si cet appareil cause des interfrences nuisibles la rception des signaux de radio ou de tlvision, ce qui peut tre dtermin en allumant et en teignant l'appareil, on encourage l'utilisateur d'essayer de corriger ces interfrences par l'un des moyens suivants:

Rorienter ou repositionner l'antenne de rception. Augmenter la distance sparant lquipement du rcepteur. Connecter lquipement une prise appartenant un circuit diffrent de celui sur lequel le rcepteur est connect. Consulter le revendeur ou un technicien radio/TV expriment pour obtenir de laide. Dans le cas o le produit fini dun sous-traitant rentre dans les limites imposes aux appareils numriques de classe A, les noncs suivants doivent tre inclus dans le manuel du produit finis:

REMARQUE : Cet appareil a t test et certifi conforme aux spcifications d'un appareil lectronique de classe A (class A digital device), conformment la partie 15 du rglement de la FCC. Ces contraintes sont destines fournir une protection raisonnable contre les interfrences nuisibles quand l'appareil est utilis dans une installation commerciale. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation rsidentielle peut entraner des interfrences nuisibles et l'utilisateur devra corriger les interfrences ses propres frais. A.2 Certification IC (a) Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux CNR (CNR) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes:

1. 2. fonctionnement indsirable de l'appareil. Cet appareil ne doit pas causer d'interfrences. Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un En outre, conformment la clause 2.6 de la norme RSS-102, la distance de conformit d'exposition RF du BLUENRG-M2SA est fixe 15 mm, comme indiqu dans les tableaux suivants. Approbation du module IC: 8976C-BNRGM0AL Conformment IC CNR-247, le module BLUENRG-M0x est rpertori comme un dispositif metteur modulaire. Ce module nest valu que pour une utilisation autonome. Les produits finis incorporant plusieurs metteurs doivent tre conformes la colocation et aux exigences d'exposition RF en concordance avec les procdures FCC multi-metteurs. Dautres metteurs fonctionnant dans des dispositifs portables exposs aux RF (par exemple, situs moins de 20 cm des personnes avec dispositifs portatifs ou ports contre le corps) peuvent ncessiter d'une approbation spare. A.2.1 Instructions d'tiquetage v Lors de l'intgration du module BLUENRG-M0x dans le produit final, le fabricant doit sassurer que les exigences en matire d'tiquetage de la IC sont satisfaites. Une dclaration doit tre place sur ltiquette extrieure du produit final indiquant que le produit comprend un module certifi. L'tiquette doit comporter les informations suivantes (ou une mention analogue que recouvre la mme notion):

Contient IC ID: 8976C-BNRGM0AL ou Ce produit contient IC ID: 8976C-BNRGM0AL Le sous-traitant doit inclure les noncs suivants sur ltiquette extrieure du produit final moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces):

Cet appareil est en conformit aux normes IC. Lutilisation est soumise aux deux conditions suivantes:

(1) cet appareil ne doit pas causer d'interfrences nocives, et

(2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir A.2.2 Instructions pour lutilisation du produit La prsente section concerne les produits finis contenant le module BLUENRG-M0x, assujettis aux normes IC. Le manuel du produit final doit contenir la dclaration suivante (ou une mention analogue que recouvre la mme notion):

Avertissement: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet quipement.

(CNR-247) Dans le cas o le produit finis dun fabriquant OEM rentre dans les limites de la Classe B (rsidentiel), les noncs suivants doivent tre inclus dans le manuel du produit finis:

Remarque : Cet quipement a t test et dclar conforme aux limitations prvues dans le cadre de la classe B des appareils numriques, dfinies par la norme CNR-247 d'Industrie Canada. Ces limites sont conues pour fournir une protection raisonnable contre toute interfrence dangereuse issue d'une installation rsidentielle. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il se peut que des interfrences se produisent dans une installation particulire. Si cet appareil cause des interfrences nuisibles la rception des signaux de radio ou de tlvision, ce qui peut tre dtermin en allumant et en teignant l'appareil, nous encourageons l'utilisateur essayer de corriger ces interfrences par l'un des moyens suivants:

Rorienter ou repositionner l'antenne de rception. Augmenter la distance sparant lquipement du rcepteur. Connecter lquipement une prise appartenant un circuit diffrent de celui sur lequel le rcepteur est connect. Consulter le revendeur ou un technicien radio/TV expriment pour obtenir de laide. Dans le cas o le produit finis dun fabriquant OEM rentre dans le cadre des limites imposes aux appareils numriques de classe A, les noncs suivants doivent tre inclus dans le manuel du produit finis:

REMARQUE: Cet appareil a t test et certifi conforme aux spcifications d'un appareil lectronique de classe A (class A digital device), conformment la norme CNR-247 d'Industrie Canada. Ces contraintes sont destines fournir une protection raisonnable contre les interfrences nuisibles quand l'appareil est utilis dans une installation commerciale. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation rsidentielle peut entraner des interfrences nuisibles et l'utilisateur devra corriger les interfrences ses propres frais. A.3 Certification CE Le module BLUENRG-M0x a obtenu une certification de conformit aux normes suivantes:

-

-

-

-

-

EN 62479:2010 EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 ETSI EN 301 489-17 V3.1.1 (2017-02) ETSI EN 301 489-1 V2.1.1 (2017-02) ETSI EN 300 328 v 2.1.1 (2016-11) Le module est certifi CE: